Adj Pinpoint GO User Manual

PINPOINT GO

©2015 ADJ Products, LLC all rights reserved. Information,

specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby dis­claim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indi­rect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsucient and negligent assembly,
installation, rigging, and operation of this product.

2/15

User Instructions

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!

PinPoint GO Introduction

PinPoint GO General Instructions

Unpacking: Thank you for purchasing the PinPoint GO by ADJ Prod-

ucts, LLC. Every PinPoint GO has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the ship­ping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your xture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are miss­ing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without rst contact­ing customer support.

Introduction: The ADJ PinPoint GO is part of a continuing pursuit to

create high quality intelligent lighting. The PinPoint GO is a bright, bat­tery powered, LED pinspot.

Customer Support: ADJ provides a customer support line, to pro-

vide set up help and to answer any question should you encounter
problems during your set up or initial operation. You may also visit us
on the web at www.adj.com for any comments or suggestions. Service
Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Stan­dard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - PinPoint GO User Manual Page 2

To optimize the performance of this product, please read these operat­ing instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this manual
with the unit, for future reference.

PinPoint GO Features

• DC Powered and Battery Powered

• Dimming 0-100%

• Fast Fade and Slow Fade

• ADJ LED RC3 Compatible (Sold Separately)

PinPoint GO Warranty Registration

The PinPoint GO carries a two year limited warranty. Please fill out the
enclosed warranty card to validate your purchase. All returned service
items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our customer support number. All pack­ages returned to the service department not displaying a R.A. number
on the outside of the package will be returned to the shipper.

PinPoint GO Cleaning

Due to fog residue, smoke, and dust cleaning the internal and exter­nal optical lenses must be carried out periodically to optimize light
output.

1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.

2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.

3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).

ADJ Products, LLC - www.adj.com - PinPoint GO User Manual Page 3

PinPoint GO Safety Precautions

PinPoint GO Battery Precautions

• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt­ age for your unit.

• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user
serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 3 for cleaning details.

• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu­ d ing amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.

ADJ Products, LLC - www.adj.com - PinPoint GO User Manual Page 4

1. Handling of Batteries

1.1 Do Not Short Circuit the Battery

Try to never short circuit the battery. It generates a very high current
which could cause the battery to overheat which may result in elec­trolyte gel leakage, harmful fumes, or explosion. The LIR tabs may
easily short-circuit by placing them on conductive surface. A short cir­cuit may lead to heat build up and damage of the battery. An appro­priate circuitry with PCM is employed to protect accidental short
circuit of the battery pack.

1.2 Mechanical shock

Droping the unit, impact hit, bending, etc. may cause failure or short­end life of the LIR battery.

2. Other

2.1 Battery connection

1). Direct soldering of wire leads or devices to the battery is strictly
prohibited.

2). Lead tabs with pre-soldered wiring shall be spot welded to the
batteries. Direct soldering may cause damage of components, such
as separator and insulator, by heat build up.

2.2 Prevention of short circuit within a battery pack

There is enough insulation layers between wiring and the batteries to
provide extra safety protection. The battery pack is constructed in a
way that no short circuit will occur which may cause smoke or re.

2.3 Do No Disassemble the Batteries

1). Never disassemble the batteries.
Doing this may cause a internal short circuit in the battery, which may
lead to harmful fumes, re, explosion, or other problems.

2). Electrolyte Gel is harmful
Electrolyte Gel should not leak from the LIR battery. Should the
electrolyte gel come into contact with the skin or eyes, ush the area
of contact immediately with fresh water and seek medical attention

immediately.

2.4 Do Not Expose the Battery to Heat or Fire

Never incinerate or dispose of the batteries in re. This may cause an
explosion, which would be very dangerous.

ADJ Products, LLC - www.adj.com - PinPoint GO User Manual Page 5

PinPoint GO Battery Precautions

PinPoint GO Operating Instructions

2.5 Do Not Expose the Battery to water or liquids

Never soak/drop the batteries in liquids such as water, seawater,
drinks such as soft drinks, juices, coee or other.

2.6 Battery Replacement

For battery replacement please contact ADJ customer support (800)
322-6337.

2.7 Do Not use a damaged Battery

The battery could be damaged during shipping, caused by shock.
Should the battery be found damaged, including damages to the
plastic casing of the battery, deformation of the battery package,
smelling of an electrolyte, or leakage of the electrolyte gel, or other,
DO NOT use the battery. A battery with a odor of electrolyte or a gel
leakage should be placed away from re to avoid re or explosion.

3. Battery Storage

When storing the battery, it should be stored at room temperature,
with a charge of at least 50%. We recommend that during long peri­ods of storage that the battery be charged every 6 months. Doing
this will prolong the life of the battery and will also make sure that the
battery charge does not fall below the 30% mark.

4. Other Chemical Reaction

Because batteries utilize a chemical reaction, battery performance
will deteriorate over time even if stored for a long period of time
without being used. In addition, if the various usage conditions such
as charge, discharge, ambient temperature, etc. are not maintained
within the specied ranges, the life expectancy of the battery maybe
shortened or the device in which the battery is used may be damaged
by electrolyte gel leakage. If the batteries cannot maintain a charge
for long periods of time, even when they are charged correctly, this
may indicate it is time to change the battery.

5. Battery Disposal

Please dispose of battery according to local regulations.

Energy Saving Mode:

There are 2 ways you can set the PinPoint GO into energy saving
mode. When the PinPoint GO is set into energy saving mode, it will
decrease the LED brightness gradually when the battery life is less
than 80% to extend the battery life. NOTE: When the unit is using

DC power, the energy saving mode cannot be used.

1. Press the MODE button for 5 seconds to switch between normal
mode and energy saving mode. When the white LED flashes 3 times,
the PinPoint GO is in normal mode. When the white LED flashes for 5
seconds the PinPoint GO is in energy saving mode.

2. Using the ADJ LED RC3, press the BLACKOUT button for 5 sec­onds to switch between normal mode and energy saving mode. When
the white LED flashes 3 times, the PinPoint GO is in normal mode.
When the white LED flashes for 5 seconds the PinPoint GO is in ener-

gy saving mode.

Low Battery Warning:

When the battery power gets below 30%, the LED will flash rapidly for
5 seconds each time the power is switched ON. After the 5 seconds,
the unit will function normally. This is a warning letting you know that
you must charge the unit soon.

Battery Recharge:

To recharge the battery, plug the supplied DC power supply into the
DC input located on the rear of the unit and plug the other end into a
matching power supply. It takes about 4.5 hours to reach full charge
with the power switch o.

Operating Power:

There are two ways to supply power to this unit; battery power or DC
power.

• DC Power - To run the unit using DC power, plug the unit into a DC
power source, and put the POWER switch into the ON position.

• Battery Power - To run the unit using Battery power, put the POWER
switch in the ON position.

ADJ Products, LLC - www.adj.com - PinPoint GO User Manual Page 6

Mode Button Lock:

The MODE button will lock itself after 30 seconds if nothing is

ADJ Products, LLC - www.adj.com - PinPoint GO User Manual Page 7

PinPoint GO Operating Instructions

PinPoint GO Color Filter Install

pressed. To unlock the unit, press the MODE button for 3 sec­onds.

Mode Operation:

Each press of the MODE button will cycle through the different oper­ating modes. The operating modes are listed below in the order that

they appear. NOTE: When power is turned OFF and turned back
ON, the unit will start in the last operating mode.

Order of Operating Modes:

• 100% Brightness • 95% Brightness • 90% Brightness

• 84% Brightness • 78% Brightness • 72% Brightness

• 66% Brightness • 60% Brightness • 54% Brightness

• 48% Brightness • 42% Brightness • 36% Brightness

• 30% Brightness • 24% Brightness • 18% Brightness

• 12% Brightness • 6% Brightness • LED Off • Fast Fade • Slow
Fade
Pressing the MODE button again after Slow Fade will return the unit
to 100% brightness. Starting the operating mode order at the begin-

ning.

PinPoint GO ADJ LED RC3 Remote

The ADJ LED RC3 infrared remote (Sold Separately) has many dif­fernet functions and gives you complete control of your PinPoint GO.
To control the your desired fixture you must aim the controller at the
front of the fixture and be no more the 30 feet away.

The PinPoint GO comes with 4 color filters and 1 frost filter. To install
one of the filters carefully remove the retainer ring in front of the lens.
Install the filter and replace the retainer ring. Make sure the filter cut out

for the infrared receiver is in the correct place.

PinPoint GO Installation

The unit has two ways that it can be installed. The unit includes
a X-Clip so that it can be installed on drop down ceilings. Always
ensure that the unit is rmly xed to avoid vibration and slipping while
operating. Always ensure that the structure to which you are attach­ing the unit is secure and is able to support a weight of 10 times the
unit’s weight. Always use a safety cable that can hold 12 times the
weight of the unit when doing this type of installation. The safety
cable should go through the eye hole nut that holds the X-Clip base in

place.

You can also install using the magantic base. To do this, remove the
X-Clip base by unscrewing the eye hole bolt. Once removed the x­ture can be stuck to anything magnetic.

The equipment must be installed by a professional, and it must
be installed in a place where it is out of the reach of people’s
grasp.

PinPoint GO Photometric Chart

BLACKOUT - Pressing this button will blackout the fixture. This but-

ton is also used to switch between normal mode and energy saving
mode. Please see Energy Saving Mode on the previous page.

AUTO RUN MODE - Press the AUTO RUN button to switch between
Fast Fade & Slow Fade. Press the SPEED button and use the “+” & “-”
buttons to adjust the fade speed. You can press the FLASH button
to activate strobing and use the “+” & “-” buttons to adjust the strobe

speed.

MANUAL MODE - Press the SELECT PROG button to activate CW
color. Use the “+” & “-” buttons to adjust the output intensity. Press
the FLASH button to activate strobing and use the “+” & “-” buttons
to adjust the strobe speed.

ADJ Products, LLC - www.adj.com - PinPoint GO User Manual Page 8 ADJ Products, LLC - www.adj.com - PinPoint GO User Manual Page 9

PinPoint GO Warranty

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the
product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product
only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or
service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay
return shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

 •LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)

 •LaserProducts=90-DayLimitedWarranty
 •L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power

supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty).

ADJ Products, LLC - www.adj.com - PinPoint GO User Manual Page 10

PinPoint GO Specifications

Model:

SPECIFICATIONS:

PinPoint GO

LED: 1 X 3W Single Cool White LED
Power: Rechargable Battery & Power
Adapter (DC13V 1A)
Power Consumption: 3W
15W (Battery Charging)
Beam Angle: 5 Degrees
15 Degrees (With Frost Filter)
Battery Charge Time: 4.5 Hours (With Power Switch Off)
Battery Life: 7.5 Hours (Full On)
11 Hours (Energy Saving Mode &
With a Full Charge)
Weight: 1 lbs./ 0.44 Kgs.
Dimensions: 7.25”(L) x 3.5”(W) x 3.75”(H)
183 x 92 x 95mm
Working Position: Any safe working position
Warranty: 2 Year (730 days)

Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: [phone] / Fax: [phone]

Web: www.adj.com / E-mail: [e-mail]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

[e-mail] / www.adj.com

Tel: [phone] / Fax: [phone]