Page 1
MONSTER BEAM
©2013 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all afliated companies hereby disclaim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsufcient and negligent assembly,
installation, rigging, and operation of this product.
9/13
User Instructions
Page 2
Monster Beam Introduction
Monster Beam General Instructions
Unpacking: Thank you for purchasing the Monster Beam by ADJ
Products, LLC. Every Monster Beam has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your xture for
any damage and be sure all accessories necessary to operate the unit
has arrived intact. In the case damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Do not return this unit to your dealer without rst contacting customer support.
Introduction: The Monster Beam is part of ADJ’s continuing pursuit
for creating high quality affordable intelligent fixtures. The Monster
Beam is a high performance, DMX intelligent, LED moonflower fixture.
This unit can be used as a stand alone unit, or in a Master/Slave conguration. The unit has three operating modes; sound active, show mode,
or controlled via DMX controller. This fixture is a great piece for retail
stores, displays, mood, architectural, interior and exterior decoration,
and clubs. This fixture is suitable for theaters, studios, retail stores, and
other similar locations.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide set up help and to answer any question
should you encounter problems during your set up or initial operation.
You may also visit us on the web at www.adj.com for any comments
or suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this manual
with the unit, for future reference.
Monster Beam Features
• 25 x 1W LEDs
• Color Strobe Effect
• Built in Microphone
• DMX-512 protocol
• 1 DMX Channel
• 3 Operating Modes - Sound Active, Show Mode, or DMX Control
• UC3 Remote Control Compatiable (Not Included)
• Power Cord Daisy Chaining (See Page 14)
Monster Beam Warranty Registration
The Monster Beam carries a 3 year (1095 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.
americandj.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ Products, LLC
customer support for a R.A. number.
Monster Beam Installation
The unit should be mounted using a mounting clamp (not provided),
afxing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slipping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
ADJ Products, LLC Supply - www.adj.com - Monster Beam User Manual Page 2
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 3
Page 3
Monster Beam Safety Precautions
Monster Beam Set Up
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 14 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
Power Supply: The ADJ Products, LLC Monster Beam contains a
automatic voltage switch, which will auto sense the voltage when it is
plugged into a power source. With this switch there is no need to worry
about the correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The Monster Beam can be controlled via DMX-512 protocol. The Monster Beam is a 1 Channel DMX unit. The DMX address is set on the rear
panel of the Monster Beam. Your unit and your DMX controller require
a approved DMX-512 110 Ohm Data cable for data input and data
output (Figure 1). We recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all professional sound and
lighting stores). Your cables should be made with
a male and female XLR connector on either end
of the cable. Also remember that DMX cable must
be daisy chained and cannot be split.
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 4
Figure 1
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 5
Page 4
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
Monster Beam Set Up
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
1
2
XLR Male Socket
1 Ground
Figure 3
DMX512 OUT
3-PIN XLR
2 Cold
3 Hot
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
5-Pin XLR DMX Connectors.
connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
3
XLR Female Socket
2 Cold
COMMON
DMX +
DMX -
3
1
2
DMX512 IN
3-PIN XLR
Figure 2
XLR Pin Conguration
1 Ground
3 Hot
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
Some manufactures use 5-pin XLR
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
Monster Beam System Menu
001
DMX Address
512
Master
Slave Mode
Slave 1
Slave 2
Sh ow 0
Sh ow 1
Show Mode
Show 12
On
Sound State
Off
0
MENU
Sound Sense
10 0
Master Slave
DMX State
Bl ackout
Last State
On
Back Light
Off
Auto Test
Fixture Time
Firmware Version
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 6
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 7
Page 5
Monster Beam System Menu
Monster Beam System Menu
DMX Address - Set the DMX Address -
1. Press the MENU button until “DMX Addresss” is displayed,
press ENTER.
2. “X” will now be displayed, “X” represents the displayed address.
Press the UP or DOWN buttons to nd your desired address.
3. Press ENTER to conrm, and then press and hold the MENU
button for at least three seconds to assign.
Slave Mode - This will let you set unit as a master or
slave in a master/slave conguration.
Note: If the unit is being run as a Stand Alone unit, it must be
set to Master.
1. Press the MENU button until “Slave Mode” is displayed,
press ENTER. Either “Master”, “Slave 1”, or “Slave 2” will be
displayed.
2. Press the UP or DOWN buttons until your desired slave mode
is displayed, press ENTER to conm.
NOTE: In a Master/Slave conguration you can make one xture the Master and then set the next xture to “Slave 2”, the
xtures will now have contrast movements to each other.
Show Mode - Show modes 0 - 12 (Factory Shows). Show
mode can run with or without sound active mode.
Note: If the unit is being run as a Stand Alone unit, it must
rst be set to Master under the Slave Mode.
1. Press the MENU button until “Show Mode” is displayed, press
ENTER.
2. “Show X” will now be displayed, “X” representing a number
between 0-12. Programs 1-12 are factory programs, while “Sh 0”
is random mode.
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 8
3. Press the UP or DOWN buttons to nd your desired show and
press ENTER to conrm. After pressing ENTER, press and hold
the MENU button for at least 3 seconds to activate.
Sound State - In this mode the unit will run in sound
active mode.
Note: If the unit is being run as a Stand Alone unit, it must
rst be set to Master under the Slave Mode.
1. Press the MENU button until “Sound State” is displayed, press
ENTER.
2. Either “On” or “Off” will now be displayed. Use the UP or
DOWN buttons to toggle between “On” and “Off”.
3. Press ENTER to conrm your selection, the press and hold the
MENU button to activate.
Sound Sense - In this mode you can adjust the sound
sensitivity of the sound active mode.
1. Press the MENU button until “Sound Sense” is displayed,
press ENTER.
2. Press the UP or DOWN buttons to adjust the sensitivity level.
The sensitivity level can be adjusted between 0 (the lowest) and
100 (most sensitive).
3. Press ENTER to set you desired level.
DMX State - This mode can be used as a precaution
mode, that in case the DMX signal is lost, the operating
mode chosen in the setup is the running mode the xture will
go into when the DMX signal is lost. You can also set this as
the operating mode you would like the unit to return to when
power is applied.
1. Press the MENU button until “DMX State” is displayed, press
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 9
Page 6
Monster Beam System Menu
Monster Beam System Menu
ENTER.
2. Either “Master/Slave”, “Blackout”, or “Last State” will be displayed. Choose an operating mode you would like the unit to
start up in when power is applied or the DMX signal is lost.
• Master/Slave - If the DMX signal is lost or power is applied, the
unit will automatically go into Master Slave mode.
• Blackout - If the DMX signal is lost or power is applied, the unit
will automatically go into stand by mode.
• Last State - If the DMX signal is lost the xture will stay in the
last DMX set up. If power is applied and this mode is set, the unit
will automatically go into the last DMX set up.
3. Press ENTER to conrm your desired set up.
Back Light - With this function you can make the back-
light automatically turn off after one minute.
1. Press the MENU button until “Back Light” is displayed, press
ENTER.
Fixture Time - With this function you can display the
running time of the unit.
1. Press the MENU button until “Fixture Time” is displayed,
press ENTER.
2. The running time of the xture will now be displayed. Press
MENU to exit.
Firmware Version - This will display the software ver-
sion
1. Press the MENU button until “Firmware Version” is displayed.
Press the ENTER button and the software vesion will be dis-
played.
2. Press the MENU button to leave this function.
2. Either “ON” or “OFF” will now be displayed. Press the UP or
DOWN buttons to select “ON” to keep the backlight on at all
times, or “OFF” to allow the backlight to turn off after 2 minutes.
Press any button to turn the backlight on again.
3. Press ENTER to conrm.
Auto Test - This function will run a self test program.
1. Press the MENU button until “Auto Test” is displayed, press
ENTER.
2. The xture will now run a self test. Press the MENU button to
exit.
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 10
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 11
Page 7
Monster Beam Universal DMX Control
Monster Beam DMX Values & Traits
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs. The Monster Beam has 1
DMX Channel.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller such as the
Elation® Show Designer™ or the Elation® DMX Operator.™
2. To run your fixture in DMX mode, set your desired DMX address
following the directions on page 8, and the set-up specifications
that come with your DMX controller.
3. Plug in the fixture via the XLR connections to any standard DMX
controller.
4. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
Monster Beam Master-Slave Configuration
Master-Slave Conguration: This function will allow you to link up
to 16 units together and operate without a controller. The units will be
sound activated. In Master-Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs.
Any unit can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina tor at the last fixture.
2. Set the Master unit to the Master setting by pressing the MENU
button until “Slave Mode” is displayed, and Press ENTER. Use the
UP and DOWN button to find “Master” and then press ENTER.
Next, set the unit to your desired operating mode.
3. For the slave units press the MENU button until “Slave Mode” is
displayed, and Press ENTER. Choose either “Slave 1” or “Slave 2”
and press ENTER. See page 8 for more info.
4. The slave units will now follow the Master unit.
Channel Value Function
1 SHOWS
0 - 7 BLACKOUT
8 - 27 SHOW 1
28 - 47 SHOW 2
48 - 67 SHOW 3
68 - 87 SHOW 4
88 - 107 SHOW 5
108 - 127 SHOW 6
128 - 147 SHOW 7
148 - 167 SHOW 8
168 - 187 SHOW 9
188 - 207 SHOW 10
208 - 227 SHOW 11
228 - 247 SHOW 12
248 - 255 RANDOM
Monster Beam UC3 Control
Blackout Blackout the unit
Function Strobe
1.Synchronous strobe in
all
2.Sound strobe in all
3.Sound strobe in color
Mode Sound(LED OFF) Show(LED is on)
Select Show
1 - 12
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 13ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 12
Page 8
Monster Beam Power Cord Daisy Chaining
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 7 xtures maximum. After 7 xtures you will need to
use a new power outlet. They must be the same xtures. DO NOT
mix xtures.
Monster Beam Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry out
the fuse holder. Remove the bad fuse and replace with a new one. The
fuse holder has a built-in socket for a spare fuse be sure not to confuse
the spare fuse with active fuse.
Monster Beam Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use a soft cloth to wipe down the outside casing.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
Monster Beam Troubleshooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
If problems are not resolved; Contact ADJ Products, LLC for service.
1-800-322-6337
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 14
Monster Beam Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the
product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product
only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or
service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay
return shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LEDs and lamps)
•LaserProducts=90-DayLimitedWarranty
•L.E.D.Products=3-year(1095days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty). Only the L.E.D.s carry a 3-year warranty
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 15
Page 9
Monster Beam Notes Monster Beam Notes
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 16
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 17
Page 10
Monster Beam Specifications
SPECIFICATIONS:
Voltage: 100V~240V 50Hz/60Hz
LEDs: 25 x 1W RGBWA LEDs (5 Red,
5 Green, 5 Blue, 5 White & 5
Amber)
Power Consumption: 40W
Beam Angle: 29 Degrees
Fuse: 7Amp
Power Cord Daisy Chain: 7 Fixtures Max. (120V)
12 Fixtures Max. (230V)
Weight: 8lbs./ 3.3Kgs.
Dimensions: 12.5” (L) x 10” (W) x 8.25” (H)
213 x 254 x 207mm
Colors: RGBWA
DMX Channels: 1 DMX Channel
Working Position: Any safe working position
Warranty: 3 Year (1095 days)
Auto Sensing Voltage: This xture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
ADJ Products, LLC - www.adj.com - Monster Beam User Manual Page 18
©ADJ Products, LLC Supply
ADJ Products, LLC World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
ADJ Products, LLC Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.americandj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...