Page 1
MOD QA60
User Instructions
Page 2
©2018 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and
instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of
their respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
DOCUMENT VERSION
Please check www.adj.com for the latest revision/update of this guide.
Date
01/19/18
Document
Version
1 1.00
Software
Version
>
DMX
Channel
Mode
Notes
4/5/6/9/10 Initial Release
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when
they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!
Page 3
MOD QA60 Table of Contents
Introduction
Features / Warranty Registration / Installation
Safety Precautions
Control Panel Layout
DMX Set Up
DMX Addressing
DMX Channel Modes
System Menu
Operating Instructions
Master-Slave Conguration
UC IR/Airstream IR Control
3
4
5
6
7
9
11
20
21
24
25
Dimmer Curve Chart
Dimensional Drawings
Housing Change / Frost Filter
Power Linking / Trouble Shooting / Cleaning
Warranty
Technical Specications
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 2
26
27
28
29
30
31
Page 4
MOD QA60 Introduction
Unpacking: Thank you for purchasing the MOD QA60 by ADJ Products, LLC. Every MOD QA60 has
been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged,
carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit
has arrived intact. In the case damage has been found or parts are missing, please contact our toll free
customer support number for further instructions. Do not return this unit to your dealer without rst
contacting customer support.
Introduction: The ADJ MOD QA60 is a DMX intelligent, high powered LED par fixture. This xture can
be used in a stand alone set up or connected in a Master/Slave set up. The MOD QA60 has seven
operating modes: Sound Active mode, Auto Run mode, Color Change mode, Color Fade mode, RGBA
Dimmer mode, Static Color mode, and DMX controlled. To optimize the performance of this product,
please read these operating instructions carefully to familiarize yourself with the basic operations of
this unit. These instructions contain important safety information regarding the use and maintenance
of this unit. Please keep this manual with the unit, for future reference.
Customer Support: ADJ provides a customer support line, to provide set up help and to answer any
question should you encounter problems during your set up or initial operation. You may also visit us
on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through
Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.
Voice: (323) 582-2650
Fax: (323) 582-2941
E-mail: support@AmericanDJ.com
Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or
moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufactures warranty. In the unlikely event your unit may require service
please contact ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 3
Page 5
MOD QA60 Features
• Multi-Colors
• Seven Operating Modes
• Electronic Dimming 0-100%
• Built in Microphone
• DMX-512 protocol
• 3-Pin & 5-Pin DMX Connection
• Five DMX Modes: 4 Channel Mode, 5 Channel Mode, 6 Channel Mode, 9 Channel Mode, and
10 Channel Mode.
• ADJ UC IR compatible and Airstream IR compatible
• Multiple Unit Power Linking (See page 29)
INCLUED:
1 x Scissor Yoke
1 x powerCON Cable
3 x Frost Filters (20/40/60 Degrees)
OPTIONAL ACCESSORIES:
MOD Kit Pearl White Housing Case (Order Code: MOD510)
MOD QA60 Warranty Registration
The MOD QA60 carries a 2 year limited warranty. Please fill out the enclosed warranty card to validate
your purchase. All returned service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside
of the return package. A brief description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If the unit is under warranty, you
must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by contacting
our customer support team on our customer support number. All packages returned to the service
department not displaying a R.A. number on the outside of the package will be returned to the shipper.
MOD QA60 Installation
The unit should be mounted using a mounting clamp (not provided), axing it to the mounting
bracket that is provided with the unit. Always ensure that the unit is rmly xed to avoid vibration
and slipping while operating. Always ensure that the structure to which you are attaching the unit is
secure and is able to support a weight of 10 times the unit’s weight. Also, always use a safety cable
that can hold 12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be installed in a place where it is out
of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 4
Page 6
MOD QA60 Safety Precautions
• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to
remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”
(15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product outdoors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 29
for cleaning details.
• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the fixture.
C. The fixture has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a marked change in performance.
E. The fixture has fallen and/or subjected to extreme handling.
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 5
Page 7
MOD QA60 Control Panel Layout
LCD DISPLAY
MODE BUTTON
SET UP BUTTON
POWER IN
POWER OUT
MODE
SET UP
UP
DOWN
DMX INPOWER IN
DMX IN
UP BUTTON
DOWN BUTTON
DMX IN
DMX OUT
DMX OUTDMX OUTPOWER OUT
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 6
Page 8
MOD QA60 DMX Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-
nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions
from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only
have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be
linked together and operate from a single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use
the shortest cable path possible. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed
anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation): The MOD QA60
can be controlled via DMX-512 protocol. The MOD QA60 has 5 DMX channel
modes. The DMX address is set on the rear panel of the MOD QA60. Your unit and
your DMX controller require a standard 3-pin XLR connector for data input and data
output (Figure 1). We recommend Accu-Cable DMX cables. If you are making your
own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may
be purchased at almost all pro lighting stores). Your cables should be made with a
male and female XLR connector on either end of the cable. Also remember that
Figure 1
DMX cable must be daisy chained and cannot be split.
Notice: Be sure to follow gures two and three when making your own cables. Do not use the ground
lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the
shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a
short circuit and erratic behavior.
XLR Male Socket
1 Ground
Figure 3
DMX512 OT
3-PIN XLR
2 Cold
3 Hot
1
3
2
COMMON
DMX +
DMX -
XLR Female Socket
2 Cold
1 Ground
3 Hot
1
3
2
DMX512 IN
3-PIN XLR
Figure 2
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 7
Page 9
MOD QA60 DMX Set Up
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
and PIN 3 (DMX +) of the last fixture.
Special Note: Line Termination.
When longer runs of cable are used, you may need to use a terminator
on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the
female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.
Termination reduces signal errors and
1
3
avoids signal transmission problems
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
Figure 4
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-512 data cables for DATA transmis-
sion in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line. When inserting
standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily
available at most electric stores. The chart below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 8
Page 10
MOD QA60 DMX Addressing
DMX ADDRESSING
All xtures should be given a DMX starting address when using a DMX controller, so the correct xture
responds to the correct control signal. This digital starting address is the channel number from which
the xture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment
of this starting DMX address is achieved by setting the correct DMX address on the digital control
display on the xture.
You can set the same starting address for all xtures or a group of xtures, or set dierent addresses
for each individual xture. Setting all xtures to the same DMX address will cause all xtures to react
in the same way, in other words, changing the settings of one channel will aect all the xtures
simultaneously.
If you set each xture to a dierent DMX address, each unit will start to “listen” to the channel number
you have set, based on the quantity of DMX channels of each xture. That means changing the settings
of one channel will only aect the selected xture.
In the case of the MOD QA60, when in 10 Channel you should set the starting DMX address of the rst
unit to 1, the second unit to 11 (10 + 1), the third unit to 21 (11 + 10), and so on. (See chart below for
more details.)
Channelmode
4 channels 1 5 9 13
5 channels 1 6 11 16
6 channels 1 7 13 19
9 channels
10 channels
Unit1
Address
1
1
Unit2
Address
10
11 21
Unit3
Address
19
Unit4
Address
28
31
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 9
Page 11
MOD QA60 4 Channel Mode
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
MOD QA60 5 Channel Mode
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
5 MASTER DIMMER
0 - 255 0% - 100%
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 10
Page 12
MOD QA60 6 Channel Mode
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
5 STROBING
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 PULSE STROBING SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBING SLOW - FAST
224 - 255 LED ON
6 MASTER DIMMER
0 - 255 0% - 100%
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 11
Page 13
MOD QA60 9 Channel Mode
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
5 STROBING
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 PULSE STROBING SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBING SLOW - FAST
224 - 255 LED ON
6 MASTER DIMMER
0 - 255 0% - 100%
7 PROGRAM SELECTION MODE
0 - 51 DIMMING MODE
52 - 102 COLOR MACRO MODE
103 - 153 COLOR CHANGE MODE
154 - 204 COLOR FADE MODE
205 - 255 SOUND ACTIVE MODE
9 CHANNEL MODE IS CONTINUED ON THE NEXT PAGE
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 12
Page 14
MOD QA60 9 Channel Mode
Channel Value Function
8 COLOR MACROS/PROGRAMS
0 - 255 COLOR MACRO MODE
SEE THE COLOR MACRO CHART ON PAGES 18-19
COLOR CHANGE PROGRAMS
0 - 15 COLOR CHANGE 1
16 - 31 COLOR CHANGE 2
32 - 47 COLOR CHANGE 3
48 - 63 COLOR CHANGE 4
64 - 79 COLOR CHANGE 5
80 - 95 COLOR CHANGE 6
96 - 111 COLOR CHANGE 7
112 - 127 COLOR CHANGE 8
128 - 143 COLOR CHANGE 9
144 - 159 COLOR CHANGE 10
160 - 175 COLOR CHANGE 11
176 - 191 COLOR CHANGE 12
192 - 207 COLOR CHANGE 13
208 - 223 COLOR CHANGE 14
224 - 239 COLOR CHANGE 15
240 - 255 COLOR CHANGE 16
COLOR FADE PROGRAMS
0 - 15 COLOR FADE 1
16 - 31 COLOR FADE 2
32 - 47 COLOR FADE 3
48 - 63 COLOR FADE 4
64 - 79 COLOR FADE 5
80 - 95 COLOR FADE 6
96 - 111 COLOR FADE 7
112 - 127 COLOR FADE 8
128 - 143 COLOR FADE 9
144 - 159 COLOR FADE 10
160 - 175 COLOR FADE 11
176 - 191 COLOR FADE 12
192 - 207 COLOR FADE 13
208 - 223 COLOR FADE 14
224 - 239 COLOR FADE 15
240 - 255 COLOR FADE 16
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 13
Page 15
MOD QA60 9 Channel Mode
Channel Value Function
8 COLOR MACROS/PROGRAMS
SOUND ACTIVE PROGRAMS
0 - 15 SOUND ACTIVE MODE 1
16 - 31 SOUND ACTIVE MODE 2
32 - 47 SOUND ACTIVE MODE 3
48 - 63 SOUND ACTIVE MODE 4
64 - 79 SOUND ACTIVE MODE 5
80 - 95 SOUND ACTIVE MODE 6
96 - 111 SOUND ACTIVE MODE 7
112 - 127 SOUND ACTIVE MODE 8
128 - 143 SOUND ACTIVE MODE 9
144 - 159 SOUND ACTIVE MODE 10
160 - 175 SOUND ACTIVE MODE 11
176 - 191 SOUND ACTIVE MODE 12
192 - 207 SOUND ACTIVE MODE 13
208 - 223 SOUND ACTIVE MODE 14
224 - 239 SOUND ACTIVE MODE 15
240 - 255 SOUND ACTIVE MODE 16
9 PROGRAM SPEED/SOUND SENSITIVITY
0 - 255 PROGRAM SPEED SLOW - FAST
0 - 255 SOUND SENSITIVITY LEAST - MOST SENSITIVE
When Channel 7 is between the values of 0-51, Channels 1-4 are used, and Channel 5 will
control strobing.
When Channel 7 is between the values of 52-102, Channel 8 is in Color Macros Mode, and
Channel 5 will control strobing.
When Channel 7 is between the values of 103-153, Channel 8 is in Color Change Mode, and
Channel 9 will control the color change speed.
When Channel 7 is between the values of 154-204, Channel 8 is in Color Fade Mode, and
Channel 9 will control the color fade speed.
When Channel 7 is between the values of 205-255, Channel 8 is in Sound Active Mode, and
Channel 9 will control the sound sensitivity.
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 14
Page 16
MOD QA60 10 Channel Mode
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
5 STROBING
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 PULSE STROBING SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBING SLOW - FAST
224 - 255 LED ON
6 MASTER DIMMER
0 - 255 0% - 100%
7 PROGRAM SELECTION MODE
0 - 51 DIMMING MODE
52 - 102 COLOR MACRO MODE
103 - 153 COLOR CHANGE MODE
154 - 204 COLOR FADE MODE
205 - 255 SOUND ACTIVE MODE
10 CHANNEL MODE IS CONTINUED ON THE NEXT PAGE
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 15
Page 17
MOD QA60 10 Channel Mode
Channel Value Function
8 COLOR MACROS/PROGRAMS
0 - 255 COLOR MACRO MODE
SEE THE COLOR MACRO CHART ON PAGES 18-19
COLOR CHANGE PROGRAMS
0 - 15 COLOR CHANGE 1
16 - 31 COLOR CHANGE 2
32 - 47 COLOR CHANGE 3
48 - 63 COLOR CHANGE 4
64 - 79 COLOR CHANGE 5
80 - 95 COLOR CHANGE 6
96 - 111 COLOR CHANGE 7
112 - 127 COLOR CHANGE 8
128 - 143 COLOR CHANGE 9
144 - 159 COLOR CHANGE 10
160 - 175 COLOR CHANGE 11
176 - 191 COLOR CHANGE 12
192 - 207 COLOR CHANGE 13
208 - 223 COLOR CHANGE 14
224 - 239 COLOR CHANGE 15
240 - 255 COLOR CHANGE 16
COLOR FADE PROGRAMS
0 - 15 COLOR FADE 1
16 - 31 COLOR FADE 2
32 - 47 COLOR FADE 3
48 - 63 COLOR FADE 4
64 - 79 COLOR FADE 5
80 - 95 COLOR FADE 6
96 - 111 COLOR FADE 7
112 - 127 COLOR FADE 8
128 - 143 COLOR FADE 9
144 - 159 COLOR FADE 10
160 - 175 COLOR FADE 11
176 - 191 COLOR FADE 12
192 - 207 COLOR FADE 13
208 - 223 COLOR FADE 14
224 - 239 COLOR FADE 15
240 - 255 COLOR FADE 16
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 16
Page 18
MOD QA60 10 Channel Mode
Channel Value Function
8 COLOR MACROS/PROGRAMS
SOUND ACTIVE PROGRAMS
0 - 15 SOUND ACTIVE MODE 1
16 - 31 SOUND ACTIVE MODE 2
32 - 47 SOUND ACTIVE MODE 3
48 - 63 SOUND ACTIVE MODE 4
64 - 79 SOUND ACTIVE MODE 5
80 - 95 SOUND ACTIVE MODE 6
96 - 111 SOUND ACTIVE MODE 7
112 - 127 SOUND ACTIVE MODE 8
128 - 143 SOUND ACTIVE MODE 9
144 - 159 SOUND ACTIVE MODE 10
160 - 175 SOUND ACTIVE MODE 11
176 - 191 SOUND ACTIVE MODE 12
192 - 207 SOUND ACTIVE MODE 13
208 - 223 SOUND ACTIVE MODE 14
224 - 239 SOUND ACTIVE MODE 15
240 - 255 SOUND ACTIVE MODE 16
9 PROGRAM SPEED/SOUND SENSITIVITY
0 - 255 PROGRAM SPEED SLOW - FAST
0 - 255 SOUND SENSITIVITY LEAST - MOST SENSITIVE
10 DIMMER CURVES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT TO UNIT SETTING7
When Channel 7 is between the values of 0-51, Channels 1-4 are used, and Channel 5 will
control strobing.
When Channel 7 is between the values of 52-102, Channel 8 is in Color Macros Mode, and
Channel 5 will control strobing.
When Channel 7 is between the values of 103-153, Channel 8 is in Color Change Mode, and
Channel 9 will control the color change speed.
When Channel 7 is between the values of 154-204, Channel 8 is in Color Fade Mode, and
Channel 9 will control the color fade speed.
When Channel 7 is between the values of 205-255, Channel 8 is in Sound Active Mode, and
Channel 9 will control the sound sensitivity.
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 17
Page 19
Color No. DMX
VAULE
RED GREEN BLUE AMBER
Color33 129-132 255 206 143 0
Color34 133-136 254 177 153 0
Color35 137-140 254 192 138 0
Color36 141-144 254 165 98 0
Color37 145-148 254 121 0 0
Color38 149-152 176 17 0 0
Color39 153-156 96 0 11 0
Color40 157-160 234 139 171 0
Color41 161-164 224 5 97 0
Color42 165-168 175 77 173 0
Color43 169-172 119 130 199 0
Color44 173-176 147 164 212 0
Color45 177-180 88 2 163 0
Color46 181-184 0 38 86 0
Color47 185-188 0 142 208 0
Color48 189-192 52 148 209 0
Color49 193-196 1 134 201 0
Color50 197-200 0 145 212 0
Color51 201-204 0 121 192 0
Color52 205-208 0 129 184 0
Color53 209-212 0 83 115 0
Color54 213-216 0 97 166 0
Color55 217-220 1 100 167 0
Color56 221-224 0 40 86 0
Color57 225-228 209 219 182 0
Color58 229-232 42 165 85 0
Color59 233-236 0 46 35 0
Color60 237-240 8 107 222 0
Color61 241-244 0
Color62 245-248 0
Color63 249-252 0 0 0
Color64 253-255
MOD QA60 Color Macro Chart
Color No. DMX
VAULE
OFF 0 0 0 0 0
Color1 1-4 80 255 234 80
Color2 5-8 80 255 164 80
Color3 9-12 77 255 112 77
Color4 13-16 117 255 83 83
Color5 17-20 160 255 77 77
Color6 21-24 223 255 83 83
Color7 25-28 255 243 77 77
Color8 29-32 255 200 74 74
Color9 33-36 255 166 77 77
Color10 37-40 255 125 74 74
Color11 41-44 255 97 77 74
Color12 45-48 255 71 77 71
Color13 49-52 255 83 134 83
Color14 53-56 255 93 182 93
Color15 57-60 255 96 236 96
RED GREEN BLUE AMBER
RGBA COLOR INTENSITY
Color16 61-64 238 93 255 93
Color17 65-68 196 87 255 87
Color18 69-72 150 90 255 90
Color19 73-76 100 77 255 77
Color20 77-80 77 100 255 77
Color21 81-84 67 148 255 67
Color22 85-88 77 195 255 77
Color23 89-92 77 234 255 77
Color24 93-96 158 255 144 144
Color25 97-100 255 251 153 153
Color26 101-104 255 175 147 147
Color27 105-108 255 138 186 138
Color28 109-112 255 147 251 147
Color29 113-116 151 138 255 138
Color30 117-120
Color31 121-124 138 169 255 138
99 0 255 100
Color32 125-128 255 255 255 255
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 18
Page 20
MOD QA60 Color Macro Chart
Color No. DMX
VAULE
Color33 129-132 255 206 143 0
Color34 133-136 254 177 153 0
Color35 137-140 254 192 138 0
Color36 141-144 254 165 98 0
Color37 145-148 254 121 0 0
Color38 149-152 176 17 0 0
Color39 153-156 96 0 11 0
Color40 157-160 234 139 171 0
Color41 161-164 224 5 97 0
Color42 165-168 175 77 173 0
Color43 169-172 119 130 199 0
Color44 173-176 147 164 212 0
Color45 177-180 88 2 163 0
Color46 181-184 0 38 86 0
RED GREEN BLUE AMBER
RGBA COLOR INTENSITY
Color47 185-188 0 142 208 0
Color48 189-192 52 148 209 0
Color49 193-196 1 134 201 0
Color50 197-200 0 145 212 0
Color51 201-204 0 121 192 0
Color52 205-208 0 129 184 0
Color53 209-212 0 83 115 0
Color54 213-216 0 97 166 0
Color55 217-220 1 100 167 0
Color56 221-224 0 40 86 0
Color57 225-228 209 219 182 0
Color58 229-232 42 165 85 0
Color59 233-236 0 46 35 0
Color60 237-240 8 107 222 0
Color61 241-244 0
Color62 245-248 0
0 255 0
0 0 255
Color63 249-252 0 0 0
Color64 253-255
0 255 0 0
255
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 19
Page 21
MOD QA60 System Menu
MENU DESCRIPTION
DMX MODE ADDR:001~512 Sets the DMX starting address
DMX MODE Set the unit DMX channels
CHAN:4/5/6/9/10
DMX MODE NO:BLACK When DMX signal is lost or interrupted,the unit will default to BLACKOUT option.It will
switch all LED’s off
DMX MODE NO:HOLD When DMX signal is lost or interrupted,the unit will default to HOLD option.It will hold the
last state before signal was lost.
DMX MODE NO:AUTO When DMX signal is lost or interrupted,the unit will default to AUTO option.It will run the
internal programs.
DMX MODE NO:MANUA When DMX signal is lost or interrupted,,the unit will default to the manual color setting
DMX MODE DELAY:0~4 Select the unit delay mode
SLAVE MODE Set the unit into slave mode
SOUND PRO:01~16 Select the 16 sound active modes
SOUND SENS:00~08 Adjust the sound active sensitivity level,00 is sound active off,01 is the lowest level,8 is
highest level.
MANUAL RED:000~255 Adjust the intensity of the red color
MANUAL GREN:000~255 Adjust the intensity of the green color
MANUAL BLUE:000~255 Adjust the intensity of the blue color
MANUAL AMBE:000~255 Adjust the intensity of the amber color
MANUAL STROB:00~15 Adjust the flash speed,00 is flash off,01 is slowest,15 is fastest
JUMP RUN SNAP:01~16 Select the 16 color change modes
JUMP RUN SPEED:01~16 Adjust the speed of the color change mode
FADE RUN SNAP:01~16 Select the 16 color dreaming modes
FADE RUN SPEED:01~16 Adjust the speed of the color dreaming mode
AUTO RUN FAD+SNAP Select the auto run mode
AUTO RUN SPEED:01~16 Adjust the speed of the auto run mode
CLR MACS COLOR:00~64 Select the 64 static colors
CLR MACS STROB:00~15 Adjust the strobe speed,00 is strobe off,01 is slowest,15 is fastest
OPTION BLGT:ON LCD backlight always on
OPTION BLGT:OFF LCD backlight will be off after 20 seconds
OPTION IR:ON IR remote function on
OPTION IR:OFF IR remote function off
OPTION SYSRESET Initialize the unit at the extra factory setting
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 20
Page 22
MOD QA60 Operating Instructions
The control panel will lock up after 5 seconds of inactivity. Press the MODE button for at least
5 seconds to unlock the contron panel.
LCD Backlight On/Off:
To set the LCD backlight to turn off after 20 seconds, press the MODE button until “OPTION BLGT: XX”
is displayed. “XX” represents the current state. Press the UP or DOWN buttons to set the backlight
to turn “OFF” after 20 seconds or “ON” to stay on at all times.
Operating Modes:
The MOD QA60 has seven operating modes:
• RGBA Dimmer Mode - Choose one of the four colors to remain static or adjust the intensity of
each color to make your desired color.
• Color Change mode - There are 16 color change modes to choose from. In color change mode the
unit will change through the various colors depending on the color change mode that is chosen.
The color change running speed is adjustable.
• Color Fade mode - There are 16 color fade modes to choose from. In color fade mode the unit will
fade through the various colors depending on the color fade mode that is chosen. The fade running
speed is adjustable.
• Auto Run Mode - In Auto Run Mode, the fixture will run a combination of color change and color
fade. The running speed is adjustable.
• Sound Active mode - The unit will react to sound, chasing through the built in programs. There
are 16 sound active modes.
• Static Color Mode - There are 64 colors to choose from.
• DMX control mode - This function will allow you to control each individual fixtures traits with a
standard DMX 512 controller.
DMX Mode:
Operating through a DMX controller gives the user the freedom to create their own programs tailored
to their own individual needs. The MOD QA60 has 5 DMX modes: 4 channel mode, 5 channel mode,
6 channel mode, 9 channel mode, and 10 channel mode. See pages 10-17 for each mode’s DMX
traits.
1. This function will allow you to control each individual fixture’s traits with a standard DMX 512
controller.
2. To run your fixture in DMX mode press the MODE button until “DMX MODE:XXX” is displayed.
“XXX” represents the current displayed DMX address. Use the UP or DOWN buttons to select
your desired DMX address, then press the SETUP button to select your DMX channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX channel modes. The channel modes are
listed below:
• “CHAN: 04” is 4 Channel DMX Mode.
• “CHAN: 05” is 5 Channel DMX Mode.
• “CHAN: 06” is 6 Channel DMX Mode.
• “CHAN: 09” is 9 Channel DMX Mode.
• “CHAN: 10” is 10 Channel DMX Mode.
4. Please see pages 10-17 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in the fixture via the XLR connections
to any standard DMX controller.
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 21
Page 23
MOD QA60 Operating Instructions
RGBA Dimmer Mode:
1. Plug the fixture in and press the MODE button until “MANUAL” is displayed. Press the SET UP
button to cycle through the RGBA colors.
2. When “RED” is displayed you are in Red dimming mode. Use the UP and DOWN buttons to
adjust intensity.
3. When “GREN” is displayed you are in Green dimming mode. Use the UP and DOWN buttons to
adjust intensity.
4. When “BLUE” is displayed you are in Blue dimming mode. Use the UP and DOWN buttons to
adjust intensity.
5. When “AMBE” is displayed you are in Amber dimming mode. Use the UP and DOWN buttons to
adjust intensity.
6. After you have adjusted the colors to make your desired color you can then activate strobing by
pressing the SET UP button to enter strobing.
7. “STROB” will be displayed, this is strobing mode. The strobing can be adjusted between “00”
(strobing off) to “15” (fastest strobing).
Color Change Mode:
1. Plug the fixture in and press the MODE button until “JUMP RUN SNAP: XX” is displayed. “XX”
represents a number between 01-16.
2. Use the UP and DOWN buttons to find your desired color change mode.
3. Press the SET UP button and “SPEED: XX” will be displayed. Use the UP and DOWN buttons to
adjust the speed of the color change. The speed can be adjusted between “01” (slowest) to
“16” (fastest).
Color Fade Mode:
1. Plug the fixture in and press the MODE button until “FADE RUN SNAP: XX” is displayed. “XX”
represents a number between 01-16.
2. Use the UP and DOWN buttons to find your desired color fade mode.
3. Press the SET UP button and “SPEED: XX” will be displayed. Use the UP and DOWN buttons to
adjust the speed of the color fade. The speed can be adjusted between “01” (slowest) to “16”
(fastest).
Auto Run Mode:
1. Plug the fixture in and press the MODE button until “AUTO RUN FAD+SNAP” is displayed.
2. Press the SET UP button and “SPEED: XX” will be displayed. Use the UP and DOWN buttons to
adjust the speed of the Auto Run. The speed can be adjusted between “01” (slowest) to “16”
(fastest).
Sound Active Mode:
1. Plug the fixture in and press the MODE button until “SOUND PROG: XX” is displayed. “XX”
represents a number between 01-16.
2. Use the UP and DOWN buttons to find your desired sound active program.
3. Press the SET UP button and “SENS: XX” will be displayed. Use the UP and DOWN buttons to
adjust the sound sensitivity. The sensitivity can be adjusted between “00” (least sensitive) to
“08” (most sensitive).
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 22
Page 24
MOD QA60 Operating Instructions
Static Color Mode:
1. Plug the fixture in and press the MODE button until “CLR MACS COLOR: XX” is displayed. “XX”
represents a number between 00-64.
2. Use the UP and DOWN buttons to scroll through the 64 colors and find you desired color. After
you have found your desired color you can activate strobing by pressing the SET UP button to
enter the strobe mode.
3. “STROB: XX” will be displayed, this is strobe mode. The strobing can be adjusted between “00”
(flash off) to “15” (fastest flash).
System Reset:
This will return the fixture to its factory settings.
1. Plug the fixture in and press the MODE button until “OPTION” is displayed.
2. Press the SET UP button until “SYSRESET” is displayed.
3. Press the UP and DOWN buttons simultaneously to reset or press the MODE button to exit.
Dimmer Curve:
This is used to set the dimming curve used with DMX mode. See page 26 for the different dimming
curves.
1. Plug the fixture in and press the MODE button until “DMX MODE ADDR: XXX” is displayed.
2. Press the SET UP button until “DELAY: X” is displayed. “X” represents the displayed dimmer
curve (0-4).
• 0 - Standard
• 1 - Stage
• 2 - TV
• 3 - Architectural
• 4 - Theatre
3. Press the UP or DOWN buttons to scroll through and select your desired dimming curve.
DMX State:
This mode can be used as a precaution mode, that in case the DMX signal is lost, the operat-
ing mode chosen in the setup is the running mode the xture will go into when the DMX signal is
lost. You can also set this as the operating mode you would like the unit to return to when power is
applied.
1. Plug the fixture in and press the MODE button until “DMX MODE ADDR:XXX” is displayed.
2. Press the SET UP button until “DMX MODE NO” is displayed. The current DMX state will be
displayed.
• “BLACK” (Blackout) - If the DMX signal is lost or interrupted, the unit will automatically go into
stand by mode.
• “HOLD” (Last State) - If the DMX signal is lost or interrupted, the xture will stay in the last DMX
set up.
• “AUTO” (Auto Run) - If the DMX signal is lost or interrupted, the unit will automatically go into
Auto Run mode.
• “MANUA” (Manual) - if the DMX signal is lost or interrupted, the unit will automatically go into the
last color set up in manual dimmer mode.
3. Press the UP or DOWN buttons to scroll through and select your desired DMX state.
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 23
Page 25
MOD QA60 Operating Instructions
ADJ UC IR & Airstream:
This function is used to activate and deactivate the infared sensor. When this function is activated
the unit can be controlled using the ADJ UC IR or Airstream IR app. Please see page 25 for remote
controls and functions.
1. Plug the fixture in and press the MODE button until “OPTION” is displayed.
2. Press the SET UP button until “IR: XX” is displayed.
3. Press the UP or DOWN buttons to either activate the remote function (On) or deactivate it (Off).
MOD QA60 Master-Slave Configuration
Master-Slave Configuration:
This function will allows the user to link units together to run in a Master-Slave set-up. In a MasterSlave set up. one unit will act as the controlling unit and the others will react to the controlling units
running mode. Any unit can act as a Master or as a Slave, however, only one unit can be programmed
to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain the units via the XLR connectors on the bottom of the unit. Use standard XLR data
cables to link the units together. Remember that the Male XLR connector is the input and the
Female XLR connector is the ouput. The first unit in the chain (master) will use the female XLR
connector only. The last unit in the chain will use the male XLR connector only.
2. Connect the rst “Slave” unit to the “Master.”
3. Set the “Master” unit to a desired mode of operation. On the “Slave” unit’s press the MODE
button until “SLAVE MODE” is displayed. The “Slave” unit(s) will now follow the “Master”.
MOD QA60 Snoot Effect
The body of the MOD QA60 can easily be adjiusted to create a Snoot Effect to eliminate side glare.
Loosen the bracket knobs and slide the innards up and down using the bracket. Find your optimal
setting and tighten the bracket knobs to lock the body in place.
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 24
Page 26
MOD QA60 ADJ UC IR/ Airstream IR Control
The UC IR infrared remote gives you control of various functions (See below). To control the fixture
you must aim the remote at the front of the fixture and be no more than 30 feet away. To use the ADJ
UC IR you must first activate the fixtures infrared sensor, to activate the sensor please see the in-
structions on page 24.
The Airstream IR remote transmitter plugs into the headphone jack of your iOS phone or tablet. To
control your IR fixture you must raise the volume to the maximum on your iOS phone or tablet and
aim the transmitter at the fixture sensor and be no more than 15 feet away. After you have purchased
the Airstream IR transmitters, the app is a free download from the app store for your iOS phone or
tablet. The app comes with 3 pages of control depending on the fixture you are using. Please see
below for IR functions including the corresponding app page.
Works with App page 1
STAND BY - Pressing this button will blackout the fixture. Press the button again to return to the
initial state.
FULL ON - Press this button down to fully light up the unit. Press any button to exit this mode..
FADE/GOBO - Press this button to switch between Color Change Mode, Color Fade Mode, and
Auto Run Mode. Use buttons 1-9 to select your desired show. Press this button twice for show 10.
Press button 1 twice for show 11.
“DIMMER +” and “DIMMER -” - Use these buttons to adjust the output intensity when color macro
mode is active.
STROBE - Press this button to activate strobing. Use buttons 1-4 to adjust the strobe speed. “1”
being the slowest, “4” being the fastest. Press this button again to stop strobing.
COLOR - Press this button to activate color mode. Use buttons 1-9 to find your desired color.
1-9 - Use buttons 1-9 to select a desired color when color macro mode is active or a desired program
when color change or color fade mode is active. Use buttons 1-4 to select a desired strobe rate
when strobing is active.
SOUND ON & OFF - Use the buttons to activate and deactivate sound active mode. When activated
sound sensitivity is at the highest. When SOUND OFF is pressed sensitvity is at its lowest.
SHOW 0 - Press this button to activate color fade mode. Use buttons 1-9 to select your desired
show. Press this button twice for show 10. Press button 1 twice for show 11.
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 25
Page 27
MOD QA60 Dimmer Curve Chart
DIMMER
100%
50%
10%
0%
Time (ms)
Rise Time Down Time
0 Sec
0 sec Fade Time 1 sec Fade Time
255 255
Dimming Curve
Ramp Effect
0 0
Rise Time (ms) Down Time (ms) Rise Time (ms) Down Time (ms)
Standard (default) 0 0 0 0
Stage 780 1100 1540 1660
TV 1180 1520 1860 1940
Architectural 1380 1730 2040 2120
Theatre 1580 1940 2230 2280
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 26
Page 28
MOD QA60 Dimensional Drawings
7.71”/196mm
5.5”/140mm
8.75”/222mm
5.48”/139.3mm
6.77”/172mm
10.37”/263.4mm
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 27
Page 29
MOD QA60 Housing Change
The MOD units housing is interchangeable. You can purchase the white housing kit through ADJ.
Changing the housing is very simple process. Follow the instructions below to change the housing.
For more help contact ADJ Customer Support.
1
2
Start by unscrewing
and removing the
bracket knobs.
4
When the screw has been
removed the and safety cable
is disconnected you are able
to remove the innards through
the top of the unit.
3
Once the knobs and bracket
have been removed, unscrew
and remove the safety cable
screw.
5
You are now able to switch
shells by carefully lowering
the innards into the new case
and reassemble. Reconnect the
safety cable and attache the
bracket and knobs.
6
MOD QA60 Frost Filter
The MOD QA60 comes with 3 interchangeable frost lters. To install the frost lter unscrew the four
thumb screws holding lens in place. Remove the lens and install the lter inside the unit. Line up the
thumb screw holes on the edges of lter with screw holes of the unit. Screw the thumb screws back
into place securing the lens. For help contact ADJ Customer Support.
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 28
Page 30
MOD QA60 Multiple Unit Power Linking
With this feature you can connect the xtures to one another using the powerCON input and
output sockets. The maximum that can be connected is 10 xtures @ 120V and 18 xtures @
240V. After the maximum connected xtures you will need to use a new power outlet.
NOTE: USE CAUTION WHEN POWER LINKING OTHER FIXTURES TO THE MOD QA60 AS THE
POWER CONSUMPTION OF OTHER LIGHTING FIXTURES WILL VARY!
MOD QA60 Trouble Shooting
Listed below are a few common problems the user may encounter, with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on
some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right
connectors; it does matter which way the inputs and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
2. Make sure that Sound Active mode is activated.
MOD QA60 Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried
out periodically to optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2. Clean the external optics with glass cleaner and a soft cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust, dew).
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 29
Page 31
MOD QA60 Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•NonL.E.D.LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect
Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par
Cans, Trussing, Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding batteries which have a 180 day lim-
ited warranty). Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.
•StarTecSeries=1YearLimitedWarranty(excluding batteries which have a 180 day limited warranty).
•ADJDMXControllers=2Year(730Days)LimitedWarranty
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 30
Page 32
MOD QA60 Specifications
with the included instructions, may cause harmful interference to radio communications. However, there is
Model:
MOD QA60
Voltage: 100V ~ 240V/50~60Hz
LEDs: 4 x 15W 4-in-1 RGBA LED’s
Working Position: Any safe working position
Power Draw: 60W
Power Linking: 10 Fixtures Max. @ 120V
18 Fixtures Max. @ 240V
Weight: 6 lbs./ 2.7 Kgs.
Dimensions: 10.37” (L) x 7.71” (W) x 8.75” (H)
263.4 x 196 x 222mm
Colors: RGBA Color Mixing
DMX Channels: 5 DMX Modes: 4/5/6/9/10
Warranty: 2 Year (730 days)
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This device uses and can radiate radio frequency energy and, if not installed and used in accordance
no guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the following methods:
· Reorient or relocate the device.
· Increase the separation between the device and the receiver.
· Connect the device to an electrical outlet on a circuit different from which the radio receiver is
connected.
· Consult the dealer or an experienced radio/TV technician for help.
ADJ Products, LLC - www.adj.com - MOD QA60 User Manual Page 31
Page 33
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-582-2941
www.adj.com / info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
The Netherlands
www.adj.eu / support@adjgroup.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...