Adj Micro Image User Manual [ru]

MICRO IMAGE RGB

Micro Image RGB General Introduction

Unpacking: Thank you for purchasing the Micro Image RGB by ADJ

Products, LLC. Every Micro Image RGB has been thoroughly tested
and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during ship­ping. If the carton appears to be damaged, carefully inspect your x­ture for any damage and be sure all equipment necessary to operate
the unit has arrived intact. In the event damage has been found or parts
are missing, please contact our toll free customer support number for
further instructions. Please do not return this unit to your dealer with-

out contacting customer support rst.

Introduction: The Micro Image RGB is a unique mini laser that proj-

ects red and green “web type” patterns. These laser patterns may be
projected on a wall, ceiling, or dance floor. The Micro Image RGB is
a stand alone fixture with 2 operating modes; sound active mode and
auto mode. The Micro Image RGB’s compact, light weight case design
make it ideal for mobile entertainers, bands, night clubs and bar. This

fixture is suitable for theaters, studios, retail stores, and other similar

locations. For best results use fog or special effects smoke to enhance
the beams projections.

Customer Support: ADJ Products, LLC provides a toll free cus-

tomer support line, to provide set up help and to answer any question
should you encounter problems during your set up or initial operation.
You may also visit us on the web at www.adj.com for any comments
or suggestions. For service related issue please contact ADJ Products,
LLC. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.

Pacic Standard Time.

Voice: [phone]

Fax: [phone]

E-mail: [e-mail]

3/13

User Instructions

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact
ADJ customer support.

PLEASE recycle the shipping carton whenever possible.

ADJ Products, LLC - www.adj.com - Micro Image RGB Instruction Manual Page 2

Micro Image RGB General Instructions Micro Image RGB Safety Precautions

!

!

Please carefully read and understand the instructions in this manual
thoroughly before attempting to operate this unit. These instructions
contain important safety information regarding the use and mainte­nance of this unit. Please keep this manual with the unit, for future
reference.

CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.

Micro Image RGB Features

• 30mW (532nm) Green Laser

• 80mW (650nm) Red Laser

• 2 Operating Modes - Sound Active Mode & Auto Mode

• RF Wireless Remote Control (Included)

• Dual Hanging Bracket

Micro Image RGB Warranty Registration

The Micro Image RGB carries a 90 day limited warranty. Please
fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight
pre-paid and accompany a return authorization (R.A.) number. If the
unit is under warranty you must provide a copy of your proof of pur­chase invoice. Please contact ADJ customer support for a R.A. num­ber.

Micro Image RGB Installation

The unit should be mounted using a mounting clamp (not provided),

afxing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slip-

ping while operating. Always ensure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10

times the unit’s weight. Also, always use a safety cable that can hold

12 times the weight of the unit when installing the xture.

The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to remove or break off the ground prong from the

electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short. Do not attempt to oper-

ate this unit if the power cord has been frayed or broken.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power cords should be routed so they are not likely to be walked

on, pinched by items placed upon or against them.

• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 10 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.

C. The unit has been exposed to rain or water.
D. The unit does not appear to operate normally or exhibits a

marked change in performance.

DANGER

VISIBLE LASER RADIATION

-AVOID DIRECT EYE EXPOSURE

LASER DIODE
WAVELENGTH : 635~650 nm
Max Output : <4.9mW
Class IIIa Laser Product

ADJ Products, LLC - www.adj.com - Micro Image RGB Instruction Manual Page 4ADJ Products, LLC - www.adj.com - Micro Image RGB Instruction Manual Page 3