ADJ Mega QPlus Go User Instructions

Mega QPlus gO

©2016 ADJ Products, LLC all rights reserved. Information,

specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby dis­claim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent as­sembly, installation, rigging, and operation of this product.

7/16

User Instructions

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!

Mega QPlus GO Introduction

Mega QPlus GO Features

Unpacking:

Products, LLC. Every Mega QPlus GO has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your xture for
any damage and be sure all accessories necessary to operate the unit
has arrived intact. In the case damage has been found or parts are
missing, please contact our toll free customer support number for fur­ther instructions. Do not return this unit to your dealer without rst con­tacting customer support.

Introduction:

ered LED par fixture. This xture can be used in a stand alone mode or
connected in a Master/Slave conguration. This wash has five operat­ing modes: Sound Active mode, Auto Run mode, RGB + UV Dimmer
mode, Static Color mode, and DMX control mode. To optimize the
performance of this product, please read these operating instructions
carefully to familiarize yourself with the basic operations of this unit.
These instructions contain important safety information regarding the
use and maintenance of this unit. Please keep this manual with the
unit, for future reference.

Customer Support: ADJ Products, LLC provides a customer support
line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.adj.com for any comments or sugges­tions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]

Thank you for purchasing the Mega QPlus GO by ADJ

The ADJ Mega QPlus GO is a DMX intelligent, high pow-

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

• Five Operating Modes

• Electronic Dimming 0-100%

• 5 Selectable Dimming Curves

• 64 Color Macros

• Built in Microphone

• DMX-512 protocol

• 3-Pin DMX Connection

• 8 DMX Modes: 1 Channel Mode, 2 Channel Mode, 3 Channel
Mode, 4 Channel Mode, 5 Channel Mode, 6 Channel Mode, 7
Channel Mode, & 8 Channel Mode.

• ADJ UC IR, (Not Included) & Airstream IR compatible

• Power Cord Daisy Chain (See page 26)

Mega QPlus GO Warranty Registration

The Mega QPlus GO carries a 2 year limited warranty. Please fill out
the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our customer support number. All pack­ages returned to the service department not displaying a R.A. number
on the outside of the package will be returned to the shipper.

Mega QPlus GO Installation

The unit should be mounted using a mounting clamp (not provided),
axing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slip­ping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 3ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 2

Mega QPlus GO Safety Precautions

Mega QPlus GO Battery Precautions

• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user
serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 31 for cleaning details.

• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu­ d ing amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.

1. Handling of Batteries

1.1 Do Not Short Circuit the Battery

Try to never short circuit the battery. It generates a very high
current which could cause the battery to overheat which may
result in electrolyte gel leakage, harmful fumes, or explosion.
The LIR tabs may easily short-circuit by placing them on con­ductive surface. A short circuit may lead to heat build up and
damage of the battery. An appropriate circuitry with PCM is
employed to protect accidental short circuit of the battery pack.

1.2 Mechanical shock

Droping the unit, impact hit, bending, etc. may cause failure or
shortend life of the LIR battery.

3. Other

3.1 Battery connection

1). Direct soldering of wire leads or devices to the battery is
strictly prohibited.

2). Lead tabs with pre-soldered wiring shall be spot welded to
the batteries. Direct soldering may cause damage of compo­nents, such as separator and insulator, by heat build up.

3.2 Prevention of short circuit within a battery pack

There is enough insulation layers between wiring and the bat­teries to provide extra safety protection. The battery pack is
constructed in a way that no short circuit will occur which may
cause smoke or re.

3.3 Do No Disassemble the Batteries

1). Never disassemble the batteries.
Doing this may cause a internal short circuit in the battery,
which may lead to harmful fumes, re, explosion, or other prob-

lems.

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 4

2). Electrolyte Gel is harmful
Electrolyte Gel should not leak from the LIR battery. Should the
electrolyte gel come into contact with the skin or eyes, ush the

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 5

Mega QPlus GO Battery Precautions Mega QPlus GO Battery Precautions

area of contact immediately with fresh water and seek medical

attention immediately.

3.4 Do Not Expose the Battery to Heat or Fire

Never incinerate or dispose of the batteries in re. This may
cause an explosion, which would be very dangerous.

3.5 Do Not Expose the Battery to water or liquids

Never soak/drop the batteries in liquids such as water, seawa­ter, drinks such as soft drinks, juices, coee or other.

3.6 Battery Replacement

For battery replacement please contact American DJ customer
support [phone].

3.7 Do Not use a damaged Battery

The battery could be damaged during shipping, caused by
shock. Should the battery be found damaged, including dam­ages to the plastic casing of the battery, deformation of the
battery package, smelling of an electrolyte, or leakage of the
electrolyte gel, or other, DO NOT use the battery. A battery with
a odor of electrolyte or a gel leakage should be placed away
from re to avoid re or explosion.

life expectancy of the battery maybe shortened or the device
in which the battery is used may be damaged by electrolyte
gel leakage. If the batteries cannot maintain a charge for long
periods of time, even when they are charged correctly, this may
indicate it is time to change the battery.

6. Battery Disposal

Please dispose of battery according to local regulations.

4. Battery Storage

When storing the battery, it should be stored at room tempera­ture, with a charge of at least 50%. We recommend that during
long periods of storage that the battery be charged every 6
months. Doing this will prolong the life of the battery and will
also make sure that the battery charge does not fall below the
30% mark.

5. Other Chemical Reaction

Because batteries utilize a chemical reaction, battery per­formance will deteriorate over time even if stored for a long
period of time without being used. In addition, if the various
usage conditions such as charge, discharge, ambient tempera­ture, etc. are not maintained within the specied ranges, the

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 7ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 6

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

POWER

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

Mega QPlus GO DMX Set Up

Mega QPlus GO DMX Set Up

Power Supply: The ADJ Mega QPlus GO contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged into
the power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that trav­els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter­minals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compli­ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):

The Mega QPlus GO can be controlled via DMX-512 protocol. The Mega
QPlus GO has 8 DMX modes, please see pages 11-12 for the dierent
modes. The DMX address is set on the back panel of the Mega QPlus
GO. Your unit and your DMX controller require a
standard 3-pin XLR connector for data input and
data output (Figure 1). We recommend Accu-Cable
DMX cables. If you are making your own cables,
be sure to use standard 110-120 Ohm shielded
cable (This cable may be purchased at almost all
pro lighting stores). Your cables should be made
with a male and female XLR connector on either
end of the cable. Also remember that DMX cable
must be daisy chained and cannot be split.

Figure 1

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con­nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.

COMMON

DMX512 OT

3-PIN XLR

1

3

2

DMX +

DMX -

3

1

2

DMX512 IN

3-PIN XLR

Figure 2

XLR Male Socket

1 Ground

2 Cold

3 Hot

XLR Female Socket

2 Cold

1 Ground

3 Hot

XLR Pin Conguration

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

Figure 3

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.

5-Pin XLR DMX Connectors.

Termination reduces signal errors and

1

avoids signal transmission problems

3

and interference. It is always advisable

2

to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

Some manufactures use 5-pin DMX-

Figure 4

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan­dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 9ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 8

Pin 1

Pin 2

Pin 3

Pin 1

Pin 2

Pin 3

Do Not Use

Do Not Use

Mega QPlus GO Operating Instructions

Mega QPlus GO Operating Instructions

System Menu: The display will lock after 30 seconds, press
the MODE button for 3 seconds to unlock.

LED Display On/Off:

To set the LED display to turn off after 10 seconds, press the MODE
button until “don” is displayed, press the UP button to display “doff”.
Now the display will disappear after 10s. Press any button to turn
the display on again. Be advised though that the display will turn off
automatically after 10 seconds.

To set the display press the MODE button until “dXX” is displayed.
Use the UP or DOWN buttons to select either:
“don” = LED display on at all times.
“doFF” = LED display shuts off after 10 seconds.

LED Display Inversion:

Follow these instructions to flip the display 180° so that the display
can be read upside down.

1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.

2. Press the SET UP button until “Stnd” is displayed.

3. Press the UP or DOWN buttons to reverse the display 180°.

Energy Saving Mode:

1. Plug the fixture in and press the MODE button until “bXXX” is dis-
played. “XX” represents the current battery life.

2. Press the SET UP button so that “bSXX” is displayed.

3. Press the UP or DOWN buttons to turn eneryg saving mode either
“On” or “Off”.

Operating Modes:

The Mega QPlus GO has five operating modes:

• RGB+UV Dimmer Mode - Choose one of the four colors to remain
static or adjust the intensity of each color to make your desired

color.

• Sound-Active mode - The unit will react to sound, chasing through
the built in programs. There are 16 sound active modes.

• Auto Run Mode - In Auto Run mode, you can choose 1 of 16
color change modes, 1 of 16 color fade modes, or a combo color

change & fade mode.

• Static Color Mode - There are 64 colors to choose from.

• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller.

DMX Mode:

Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The Mega

QPlus GO has 8 DMX modes: 1 channel mode, 2 channel mode, 3
channel mode, 4 channel mode, 5 channel mode, 6 channel mode,
7 channel mode, and 8 channel mode. See page’s 20-27 for each
mode’s DMX traits.

1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller.

2. To run your fixture in DMX mode press the MODE button until
“d.XXX” is displayed. “XXX” represents the current displayed DMX
address. Use the UP or DOWN buttons to select your desired
DMX address, then press the SETUP button to select your DMX
Channel mode.

3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:

• To run the 1 Channel Mode, press the MODE button until “Ch01”
is displayed. This is the 1 Channel DMX Mode.

• To run the 2 Channel Mode, press the MODE button until “Ch02”
is displayed. This is the 2 Channel DMX Mode.

• To run the 3 Channel Mode, press the MODE button until “Ch03”
is displayed. This is the 3 Channel DMX Mode.

• To run the 4 Channel Mode, press the MODE button until “Ch04”
is displayed. This is the 4 Channel DMX Mode.

• To run the 5 Channel Mode, press the MODE button until “Ch05”
is displayed. This is the 5 Channel DMX Mode.

• To run the 6 Channel Mode, press the MODE button until “Ch06”
is displayed. This is the 6 Channel DMX Mode.

• To run the 7 Channel Mode, press the MODE button until “Ch07”
is displayed. This is the 7 Channel DMX Mode.

• To run the 8 Channel Mode, press the MODE button until “Ch08”
is displayed. This is the 8 Channel DMX Mode.

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 10 ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 11

Mega QPlus GO Operating Instructions

Mega QPlus GO Operating Instructions

4. Please see pages 20-27 for DMX values and traits.

5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control-

ler.

RGB+UV Dimmer Mode:

1. Plug the fixture in and press the MODE button until:

2. When “r.XXX” is displayed you are in Red dimming mode. Press
the UP and DOWN buttons to adjust intensity.

3. When “G.XXX” is displayed you are in Green dimming mode.
Press the UP and DOWN buttons to adjust intensity.

4. When “b.XXX” is displayed you are in Blue dimming mode. Press
the UP and DOWN buttons to adjust intensity.

5. When “u.XXX” is displayed you are in UV dimming mode. Press
the UP and DOWN buttons to adjust intensity.

6. After you have adjusted the RGB & UV colors to make your
desired color you can then activate strobing by pressing the SET
UP button to enter the Flash (strobe) mode.

7. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).

Sound Active Mode:

1. Plug the fixture in and press the MODE button until “SoXX” is dis­ played. “XX” represents the current sound active mode (1-16).

2. Use the UP or DOWN buttons to find your desired sound active

mode.

3. Press the SET UP button to enter sound sensitivity adjustment.
“SJ-X” will be displayed. Use the UP or DOWN buttons to adjust
the sensitivity. “SJ-1” is the lowest sensitivity, “SJ-8” is the high-

est.

Auto Run Mode:

There are 3 types of Auto Run Modes to choose from; Color Fade,
Color Change, and both modes running together.

is adjustable in all 3 modes.

1. Plug the fixture in and press the MODE button until either “AFXX”,
“AJXX”, or “A-JF” is displayed.

• AFXX = Color Fade mode, there are 16 Color Fade modes to
choose from. Use the UP or DOWN buttons to scroll through the

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 12 ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 13

The running speed

different Auto Fade modes.

• AJXX = Color Change mode, there are 16 Color Change modes to
choose from. Use the UP or DOWN buttons to scroll through the
different Auto Change modes.

• A-JF = Both Color Fade and Color Change modes running.

2. After you have chosen your desired running mode press the SET
UP button until “SP.XX” is displayed. When this is displayed you
can adjust the running speed of your desired program. Use the
UP or DOWN button to adjust the speed between “SP.01” (slow­ est) and “SP.16” (fastest). Once you have set your desired running
speed, press the SET UP button to return to your desired Auto
Run Mode.

Static Color Mode:

1. Plug the fixture in and press the MODE button until “CLXX” is dis-

played.

2. There are 64 colors to choose from. Select your desired color by
pressing the UP and DOWN buttons. After you have selected your
desired color you can activate strobing by pressing the SET UP
button to enter the Flash (strobe) mode.

3. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).

DMX State:

This mode can be used as a precaution mode, that in case the DMX
signal is lost, the operating mode chosen in the setup is the running
mode the xture will go into when the DMX signal is lost. You can also
set this as the operating mode you would like the unit to return to when

power is applied.

1. Plug the fixture in and press the MODE button until “d.XXX” is dis-
played. “XXX” represents the current displayed DMX address.

2. Press the SET UP button so that “nodn” is displayed. Use the UP
and DOWN buttons to scroll through the DMX states.

• “bLAC” (Blackout) - If the DMX signal is lost or interrupted,
the unit will automatically go into stand by mode.

• “LASt” (Last State) - If the DMX signal is lost or interrupted,
the xture will stay in the last DMX set up. If power is applied and
this mode is set, the unit will automatically go into the last DMX set
up.

Mega QPlus GO Operating Instructions

Mega QPlus GO Master-Slave Configuration

• “ProG” (Auto Run) - If the DMX signal is lost or interrupted,
the unit will automatically go into Auto Run mode.

3. After you have found your desired setting, press SET UP to exit.

Dimmer Curve:

This is used to set the dimming curve used with DMX mode. See
page 30 for the dimming curves chart.

1. Plug the fixture in and press the MODE button until “d.XXX” is dis-
played. “XXX” represents the current displayed DMX address.

2. Press the SET UP button until “dr-X” is displayed. “X” represents
the displayed dimmer curve (0-4).

• 0 - Standard

• 1 - Stage

• 2 - TV

• 3 - Architectural

• 4 - Theatre

3. Press the UP or DOWN buttons to scroll through and select your
desired dimming curve.

Activate IR Sensor:

This function is used to activate and deactivate the IR sensor. When
this function is activated you can control the fixture using the UC IR,
or Airstream IR App. Please see page 16 for controls and functions.

1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.

2. Press the SET UP button until “IrXX” is displayed. “XX” represents
either “on” or “oF”.

3. Press the UP or DOWN buttons to either activate the remote func­ tion (On) or deactivate it (Off).

Master-Slave Configuration:

This function will allows you to link units together to run in a Master­Slave set-up. In a Master-Slave set-up one unit will act as the control-

ling unit and the others will react to the controlling units built-in pro­grams. Any unit can act as a Master or as a Slave however, only one

unit can be programmed to act as the “Master.”

Master-Slave Connections and Settings:

1. Daisy chain your units via the XLR connector on the rear of
the unit. Use standard XLR data cables to link your units together.
Remember that the Male XLR connector is the input and the Female
XLR connector is the ouput. The first unit in the chain (master) will use
the female XLR connector only. The last unit in the chain will use the
male XLR connector only.

2. Connect the rst “Slave” unit to the “Master.”

3. Set the “Master” unit to your desired mode of operation. Set the
“Slave” unit(s) to the DMX address setting of 001.The “Slave”
unit(s) will now follow the “Master”.

Mega QPlus GO CAD Drawing

142.44mm/5.60”

178mm/7”

207mm/8.14”

226.2mm/8.90”

Default Running Mode:

This is a default running mode. When this mode is activated all modes
will return to their default settings.

1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.

2. Press the SET UP button until “dEFA” is displayed.

3. Press the UP and DOWN buttons simultaneously. Press the
MODE button to exit.

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 14 ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 15

226.2mm/8.90”

164mm/6.45”

Mega QPlus GO UC IR & Airstream App Control

Mega QPlus GO 1 Channel Mode

The UC IR (sold separately) infrared remote gives you control of
various functions (See below). To control the fixture you must aim the
remote at the front of the fixture and be no more than 30 feet away.
To use the ADJ UC IR you must first activate the fixtures infrared sen­sor, to activate the sensor please see the instructions on page 14.

The Airstream IR (sold separately) remote transmitter plugs into the
headphone jack of your iOS phone or tablet. To control your IR fixture
you must raise the volume to the maximum on your iOS phone or tab­let and aim the transmitter at the fixture sensor and be no more than
15 feet away. After you have purchased the Airstream IR transmitters,
the app is a free download from the app store for your iOS phone
or tablet. The app comes with 3 pages of control depending on the
fixture you are using. Please see below for IR functions including the

corresponding app page.

Works with App page 1.

STAN D BY - Pressing this button will blackout the fixture. Press the

button again to return to the initial state.

FULL ON - Hold this button down to fully light up the unit. When you
let the button go, the unit will return to its previous state.

FADE/GOBO - This button activates color fade mode.

Channel Value Function

1 COLOR MACROS

0 - 255 See the Color Macro Chart on page 23

Mega QPlus GO 2 Channel Mode

Channel Value Function

1 COLOR MACROS

0 - 255 See the Color Macro Chart on page 23
2 MASTER DIMMER
0 - 255 0% - 100%

Mega QPlus GO 3 Channel Mode

Channel Value Function

1 COLOR MACROS

0 - 255 See the Color Macro Chart on page 23
2 MASTER DIMMER
0 - 255 0% - 100%
3 STROBE
0 - 15 OFF
16 - 255 STROBING SLOW - FAST

“DIMMER +” and “DIMMER -” - These buttons are used to adjust
the color output intensity in static color mode.

STROBE - Press and hold this button for strobing.

COLOR - Press this button to activate color mode. Use buttons 1-9

to find your desired color.

1-9 - Use buttons 1-9 to select your desired color when color mode is
active, and your desired show when show mode is active.

SOUND ON & OFF - Use the buttons to activate and deactivate
sound active mode.

SHOW 0 - Press this button to activate show mode. Use buttons 1-9
to find your desired show. Press the Show 0 button twice to run show
10, and button 1 twice to run show 11.

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 16 ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 17

Mega QPlus GO 4 Channel Mode

Channel Value Function

1 RED

0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 UV
0 - 255 0% - 100%

Mega QPlus GO 5 Channel Mode

Mega QPlus GO 7 Channel Mode

Channel Value Function

1 RED

0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 UV
0 - 255 0% - 100%
5 MASTER DIMMER
0 - 255 0% - 100%

Mega QPlus GO 6 Channel Mode

Channel Value Function

1 RED

0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 UV
0 - 255 0% - 100%
5 MASTER DIMMER
0 - 255 0% - 100%
COLOR MACROS
6 0 - 255 See the Color Macro Chart on page 23

Channel Value Function

1 RED

0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 UV
0 - 255 0% - 100%
5 MASTER DIMMER
0 - 255 0% - 100%
6 STROBE
0 - 15 OFF
16 - 255 STROBING SLOW - FAST
COLOR MACROS
7 0 - 255 See the Color Macro Chart on page 23

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 18 ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 19

Mega QPlus GO 8 Channel Mode

Mega QPlus GO 8 Channel Mode

Channel Value Function

1 RED

0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 UV
0 - 255 0% - 100%
5 MASTER DIMMER
0 - 255 0% - 100%
6 STROBE/PROGRAM SPEED/
SOUND SENSITIVITY
0 - 15 STROBING OFF
16 - 255 STROBING SLOW - FAST
0 - 255 PROGRAM SPEED SLOW - FAST
0 - 255 SOUND LEAST SENS - MOST SENS

7 PROGRAM SELECTION MODE
0 - 51 DIMMING MODE
52 - 102 COLOR MACRO MODE
103 - 153 COLOR CHANGE MODE
154 - 204 COLOR FADE MODE
205 - 255 SOUND ACTIVE MODE
8 COLOR MACROS/PROGRAMS/

SOUND ACTIVITY

0 - 255 COLOR MACRO MODE
See the Color Macro Chart on page 23

COLOR CHANGE PROGRAMS
0 - 15 COLOR CHANGE 1
16 - 31 COLOR CHANGE 2
32 - 47 COLOR CHANGE 3
48 - 63 COLOR CHANGE 4
64 - 79 COLOR CHANGE 5
80 - 95 COLOR CHANGE 6

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 20 ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 21

Channel Value Function

8 COLOR MACROS/PROGRAMS/

SOUND ACTIVITIY

COLOR CHANGE PROGRAMS
96 - 111 COLOR CHANGE 7
112 - 127 COLOR CHANGE 8
128 - 143 COLOR CHANGE 9
144 - 159 COLOR CHANGE 10
160 - 175 COLOR CHANGE 11
176 - 191 COLOR CHANGE 12
192 - 207 COLOR CHANGE 13
208 - 223 COLOR CHANGE 14
224 - 239 COLOR CHANGE 15
240 - 255 COLOR CHANGE 16

COLOR FADE PROGRAMS
0 - 15 COLOR FADE 1
16 - 31 COLOR FADE 2
32 - 47 COLOR FADE 3
48 - 63 COLOR FADE 4
64 - 79 COLOR FADE 5
80 - 95 COLOR FADE 6
96 - 111 COLOR FADE 7
112 - 127 COLOR FADE 8
128 - 143 COLOR FADE 9
144 - 159 COLOR FADE 10
160 - 175 COLOR FADE 11
176 - 191 COLOR FADE 12
192 - 207 COLOR FADE 13
208 - 223 COLOR FADE 14
224 - 239 COLOR FADE 15
240 - 255 COLOR FADE 16

Mega QPlus GO 8 Channel Mode

Channel Value Function

8 COLOR MACROS/PROGRAMS/

SOUND ACTIVITY

SOUND ACTIVE PROGRAMS
0 - 15 SOUND ACTIVE MODE 1
16 - 31 SOUND ACTIVE MODE 2
32 - 47 SOUND ACTIVE MODE 3
48 - 63 SOUND ACTIVE MODE 4
64 - 79 SOUND ACTIVE MODE 5
80 - 95 SOUND ACTIVE MODE 6
96 - 111 SOUND ACTIVE MODE 7
112 - 127 SOUND ACTIVE MODE 8
128 - 143 SOUND ACTIVE MODE 9
144 - 159 SOUND ACTIVE MODE 10
160 - 175 SOUND ACTIVE MODE 11
176 - 191 SOUND ACTIVE MODE 12
192 - 207 SOUND ACTIVE MODE 13
208 - 223 SOUND ACTIVE MODE 14
224 - 239 SOUND ACTIVE MODE 15
240 - 255 SOUND ACTIVE MODE 16

Mega QPlus GO Color Macro Chart

RGB+UV COLOR IN TE NSITY

VAULE

144 Color57 225-228 209 219 182 0

When Channel 7 is between the values of 0-51, Channels 1-4 are used,
and Channel 6 will control strobing.

When Channel 7 is between the values of 52-102, Channel 8 is in Color
Macros Mode, and Channel 6 will control strobing.

When Channel 7 is between the values of 103-153, Channel 8 is in Color
Change Mode, and Channel 6 will control the color change speed.

When Channel 7 is between the values of 154-204, Channel 8 is in Color
Fade Mode, and Channel 6 will control the color fade speed.

When Channel 7 is between the values of 205-255, Channel 8 is in Sound
Active Mode, and Channel 6 will control the sound sensitivity.

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 22 ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 23

RGB+UV COLOR INTENSITY Color No. DMX

RED GREEN BLUE UV RED G REE N BLUE UV

VAULE

Color1 1-4 80 255 234 80 Color34 133-136 254 177 153 0

Color0(off) 0 0 0 0 0 Color33 129-132 255 206 143 0

Color No. DMX

Color3 9 -12 77 255 112 77 Color36 141-144 254 165 98 0

Color2 5-8 80 255 164 80 Color35 137-140 254 192 138 0

Color4 13-16 117 255 83 8 3 Color37 145-148 254 121 0 0

Color8 29-32 255 200 74 74 Color41 161-164 224 5 97 0

Color9 33-36 255 166 77 77 Color42 165-168 175 77 173 0

Color6 21-24 223 255 83 83 Color39 153-156 96 0 11 0

Color7 25-28 255 243 77 77 Color40 157-160 234 139 171 0

Color5 17-20 160 255 77 77 Color38 149-152 176 17 0 0

5 83 134 83 Color46 181-184 0 38 86 0

Color30 117-120 151 138 255 138 Color63 249-252 0 0 255 0

Color29 113-116 151 138 255 138 Color62 245-248 165 198 247 0

Color12 45-48 255 71 77 71 Color45 177-180 88 2 163 0

Color13 49-52 25

Color11 41-44 255 97 77 74 Color44 173-176 147 164 212 0

Color10 37-40 255 125 74 74 Color43 169-172 119 130 199 0

Color14 53-56 255 93 182 93 Color47 185-188 0 142 208 0

Color15 57-60 255 96 236 96 Color48 189-192 52 148 209 0

Color16 61-64 238 93 255 93 Color49 193-196 1 134 201 0

Color17 65-68 196 87 255 87 Color50 197-200 0 145 212 0

Color18 69-72 150 90 255 90 Color51 201-204 255 0 0 0

Color19 73-76 100 77 255 77 Color52 205-208 0 255 0 0

Color20 77-80 77 100 255 77 Color53 209-212 0 83 115 0

Color21 81-84 67 148 255 67 Color54 213-216 0 97 166 0

Color22 85-88 77 195 255 77 Color55 217-220 1 100 167 0

Color23 89-92 77 234 255 77 Color56 221-224 0 40 86 0

Color24 93-96 158 255 144

Color28 109-112 255 147 251 147 Color61 241-244 107 156 231 0

Color27 105-108 255 138 186 138 Color60 237-240 8 107 222 0

Color26 101-104 255 175 147 147 Color59 233-236 0 46 35 0

Color25 97-100 255 251 153 153 Color58 229-232 42 165 8 5 0

Color32 125-128 255 255 255 255

Color31 121-124 138 169 255 138 Color64 253-255 0 0 0 255

Mega QPlus GO Battery Status & Recharge Mega QPlus GO Photometric Chart

Battery Status:

This function is used to check the life status of the battery.
Plug the fixture in and press the MODE button until “bXXX” is
displayed. “XXX” represents an number between “000” and
“100”. The number that is displayed is the remaining battery
life. If “b---” is displayed, it means the battery is dead or you are
running the unit on AC power. Please do not let the battery

fully die, this severly shortens the life of the battery.

Example: If “b050” is displayed, the battery is at half life. If

“b025” is displayed, the battery is at 25% life.

NOTE: When the battery is charging or if the battery life is
below 30% the digital display will flash.

Mega QPlus GO Dimmer Curve Chart

NOTE: After 20 seconds of inactivity, the display will revert
back to the battery life display.

Battery Recharge: To recharge the battery, plug the supplied

AC cord into the AC input on the side of the unit and plug the
other end into a matching power supply. It takes about 4 hours
to reach full charge. The display will STOP ashing when the

unit reaches 100% charge.

Note: When unplugging the unit from charging and then
applying power via battery, there will be a minimal charge
drop.

For a faster recharge, put the Load Switch in the “O” position
and the Battery Switch in the “ON” position.

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 24 ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 25

Ramp Effect

Standard

Stage

TV

Architectural

Theatre

(Fade Time) (Fade Time)

Mega QPlus GO Power Cord Daisy Chain

With this feature you can connect the xtures to one another

using the IEC input and output sockets. The quantity that can be

connected is 20 xtures maximum. After 20 xtures you will need
to use a new power outlet. They must be the same xtures. DO
NOT mix xtures.

Mega QPlus GO Fuse Replacement

Disconnect the unit from its power source. Remove the power cord
from the unit. Once the cord has been removed, you will find that the
fuse holder is located inside the power socket. Insert a flat-head screw
driver into the power socket and gently pry out the fuse holder. Remove
the bad fuse and replace with a new one. The fuse holder also has a
holder for a spare fuse.

Mega QPlus GO Trouble Shooting

Listed below are a few common problems the user may encounter,
with solutions.

Unit not responding to DMX:

1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.

Unit does not respond to sound:

1. Quiet or high pitched sounds will not activate the unit.

2. Make sure that Sound Active mode is activated.

Mega QPlus GO Cleaning

Due to fog residue, smoke, and dust cleaning the internal and exter­nal optical lenses must be carried out periodically to optimize light
output.

1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.

2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.

3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 26

Mega QPlus GO Warranty

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

 •LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)

 •LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month

limited warranty)

 •L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-

ranty). Only the L.E.D.s carry a 2-year warranty (excludingStarTecSerieswhichacarriesa1Year

LimitedWarranty)Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.

•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 27

Mega QPlus GO Notes Mega QPlus GO Notes

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 28

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 29

Mega QPlus GO Specifications

Model:

Voltage: 100V ~ 240V/50~60Hz
LEDs: 5 x 4W RGB+UV (4-in-1)
Beam Angle: 40 Degrees
Working Position: Any safe working position
Power Draw: 28W
Power Cord Daisy Chain: 20 Fixtures Max.
Fuse: 2 Amp
Weight: 4lbs./ 1.9Kgs.
Dimensions: 5.5” (L) x 9” (W) x 10” (H)
253 x 227 x 140mm
Colors: RGB + UV Mixing
DMX Channels: 8 DMX Modes: 1 Channel Mode,
2 Channel Mode, 3 Channel Mode,
4 Channel Mode, 5 Channel Mode,
6 Channel Mode, 7 Channel Mode, &
8 Channel Mode
Battery Charge Time: 4 Hours (With Load Switch OFF)
Battery Life w/ Full Charge: 16 Hours (Single Color)
16 Hours (Sound Active)
16 Hours (Fade Mode)
6 Hours (Full On)
Battery Lifetime*: Average Lifetime is 500 Charges
Battery Type: Fixed Lithium Battery
Battery Energy: 73.26WH (Watt Hours)
Battery Weight: 1lbs. / 0.42kg
Battery Voltage: 11.1V
Battery Capacity: 6.6AH
Total Lithium Ion Cells: 9pcs

Battery Wrap Material: PVC Sleeving + Highland Barley Paper

Mega QPlus GO

Warranty: 2 Year (730 days)

*This depends on charging frequency

Please Note: Specications and improvements in the design of this
unit and this manual are subject to change without any prior written

notice.

ADJ Products, LLC - www.adj.com - Mega QPlus GO User Manual Page 30

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: [phone] / Fax: [phone]

Web: www.adj.com / E-mail: [e-mail]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

[e-mail] / www.adj.eu

Tel: [phone] / Fax: [phone]