ADJ Mega Beam Bar mega_beam_bar.pdf

MEGA BEAM BAR

Mega Beam Bar Introduction

Unpacking: Thank you for purchasing the Mega Beam Bar by ADJ
Products, LLC. Every Mega Beam Bar has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.

If the carton appears to be damaged, carefully inspect your xture for

any damage and be sure all accessories necessary to operate the unit
has arrived intact. In the case damage has been found or parts are
missing, please contact our toll free customer support number for fur­ther instructions. Do not return this unit to your dealer without rst con­tacting customer support.

Introduction: The ADJ Mega Beam Bar is part of a continuing pursuit
to create high quality intelligent lighting. The Mega Beam Bar is an

linear fixture that produces 16 sharp, 13.5 degree beams of light. This
lighting system features six RGB color mixing LED fixtures. This xture

can be used in a stand alone mode or connected in a Master/Slave

conguration. This system has six operating modes: Sound Active
mode, Auto Run mode, Built-In Program mode, Static Color Mode,
RGB dimmer mode, and DMX control mode. This fixture is suitable for

theaters, studios, retail stores, and other similar locations.

Customer Support: ADJ Products, LLC provides a customer support
line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.adj.com for any comments or sugges-

tions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]

5/13

User Instructions

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 2

Mega Beam Bar Features

Mega Beam Bar Safety Precautions

• Mulit-Colors

• 3 Operating Modes

• Electronic Dimming 0-100%

• Built in Microphone

• DMX-512 protocol

• 3-Pin DMX Connection

• 4 DMX Modes: 2 Channel Mode, 4 Channel Mode, 8 Channel

Mode, & 10 Channel Mode

• UC3 Compatiable (Not Included)

Mega Beam Bar Warranty Registration

The Mega Beam Bar carries a 3 year limited warranty. Please fill out
the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-paid

and accompany a return authorization (R.A.) number. The R.A. number

must be clearly written on the outside of the return package. A brief

description of the problem as well as the R.A. number must also be

written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of

purchase invoice. You may obtain a R.A. number by contacting our

customer support team on our customer support number. All pack-

ages returned to the service department not displaying a R.A. number

on the outside of the package will be returned to the shipper.

Mega Beam Bar Installation

The unit should be mounted using a mounting clamp (not provided),
afxing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slip-

ping while operating. Always ensure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture.

The equipment must be installed by a professional, and it must be

installed in a place where it is out of the reach of people’s grasp.

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out`

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 17 for cleaning details.

• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu­ d ing amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a

marked change in performance.

ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 4ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 3

Mega Beam Bar Set Up

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

POWER

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

Mega Beam Bar Set Up

Power Supply: The ADJ Mega Beam Bar contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged into
a power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that trav­els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter­minals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of

different manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compli­ant. To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):

The Mega Beam Bar can be controlled via DMX-512 protocol. The Mega
Beam Bar has 4 DMX channel modes, please see page 8 for the different
modes. The DMX address is set on the back panel of the Mega Beam Bar.
Your unit and your DMX controller require a stan­dard 3-pin XLR connector for data input and data
output (Figure 1). We recommend Accu-Cable
DMX cables. If you are making your own cables,
be sure to use standard 110-120 Ohm shielded
cable (This cable may be purchased at almost all
pro lighting stores). Your cables should be made
with a male and female XLR connector on either
end of the cable. Also remember that DMX cable

must be daisy chained and cannot be split.

ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 5

Figure 1

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con­nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

COMMON

1

DMX512 IN

3

3-PIN XLR

2

Figure 2

XLR Pin Conguration

1 Ground

3 Hot

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

When longer runs of cable are

Figure 4

Pin 1

Pin 2

Pin 3

Do Not Use

Do Not Use

XLR Male Socket

1 Ground

DMX512 OUT

3-PIN XLR

2 Cold

3 Hot

1

3

2

DMX +

DMX -

XLR Female Socket

2 Cold

Figure 3

Special Note: Line Termination.

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

5-Pin XLR DMX Connectors.

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan­dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 6

Termination reduces signal errors and

1

avoids signal transmission problems

3

and interference. It is always advisable

2

to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

Some manufactures use 5-pin DMX-

3-Pin XLR to 5-Pin XLR Conversion

Pin 1

Pin 2

Pin 3

Mega Beam Bar System Menu

Mega Beam Bar System Menu

System Menu: When making adjustments press ENTER

to conrm your setup and then press and hold the MENU

button for at least 3 seconds. To exit without making any
adjustments press the MENU button.

ADDR - DMX Address Setting.

1. Press the either the MENU, UP, or DOWN buttons until
“ADDR” is displayed, press ENTER.

2. The current address will now be displayed and ashing. Press
the UP or DOWN buttons to nd your desired address. Press
ENTER and then press and hold the MENU button to set your
desired DMX address.

CHND - This will let select your desired DMX channel

mode.

1. Press the either the MENU button until “CHND” is displayed,
press ENTER. Either “2CH”, “4CH”, “8CH”, or “10CH” will be

displayed

ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 7

2. Press the UP or DOWN buttons to choose your desired DMX
mode and press ENTER to conm and exit.

SLND - This will let you set unit as a master or slave in a

master/slave conguration.

1. Press the MENU button until “SLND” is displayed, press
ENTER. Either “MAST”, “SL 1” or “SL 2” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is
displayed, press ENTER and then press and hold the MENU
button to conm.

NOTE: In a Master/Slave conguration you can set one xture
to Master and then set the next xture to “SL 2”, the xtures will

now have contrast movement to each other.

ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 8

Mega Beam Bar System Menu Mega Beam Bar System Menu

SHND: SH 0 - SH12 - Show modes 0-12 (Factory pro-

grams). Show mode can run with or without sound active
mode.

1. Press the MENU button until “SHND” is displayed, press
ENTER.

2. “Sh X” will now be displayed, “X” representing a number
between 0-12. Programs 1-12 are factory programs, while “Sh
0” is random mode. Press the UP or DOWN buttons to nd your

desired show.

3. When you have found your desired show press ENTER, then
press and hold the MENU button for at least 3 seconds to acti-

vate.

SOUN - Sound Active mode.

1. Press the MENU button until “SOUN” is displayed, press
ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to activate sound active mode,
or “OFF” to deactivate sound active mode.

3. Press ENTER, and then press and hold the MENU button for
at least 3 seconds to activate.

SENS - Sound sensitivity control.

1. Press the MENU button until “SENS” is displayed, press ENTER.

2. The display will show a number between 0-100. Press the UP or
DOWN buttons to adjust the sound sensitivity. 0 being the least sensi­tive and 100 the most sensitive.

3. Press the ENTER button to conrm.

in case the DMX signal is lost, the operating mode chosen in

the setup is the running mode the xture will go into when

the DMX signal is lost. You can also set this as the operat­ing mode you would like the unit to return to when power is
applied.

1. Press the MENU button until “DNST” is displayed, press
ENTER.

2. Either “MAST”, “BLND”, or “LAST” will be displayed. Choose

an operating mode you would like the unit to start up in when

power is applied or the DMX signal is lost.

• MAST (Master Slave) - If the DMX signal is lost or power is

applied, the unit will automatically go into Master Slave mode.

• BLND (Blackout) - If the DMX signal is lost or power is applied,

the unit will automatically go into stand by mode.

• LAST (Last State) - If the DMX signal is lost the xture will stay
in the last DMX set up. If power is applied and this mode is set,
the unit will automatically go into the last DMX set up.

3. Press ENTER to conrm your desired set up

LED - With this function you can have the LED display

turn off after 10 seconds.

1. Press the MENU button until “LED” is displayed, press
ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at
all times, or “OFF” to switch to have the LED display switch off
after 10 seconds. To make the display reappear, press and hold
the MENU button for at least 5 secs.

3. Press ENTER to conrm. To make the display reappear, press
and hold the MENU button for at least 5 secs.

DNST - This mode can be used as a precaution mode, that

ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 10ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 9

Mega Beam Bar System Menu

Mega Beam Bar Operation

DISP - This will “ip” the LED display 180º.

1. Press the MENU button until “DISP” is displayed, press ENTER.

2. Either “DISP” or “DSIP” will now be displayed. Press the
ENTER button to “ip” the display.

TEST - This function will run a self test program.

1. Press the MENU button until “TEST” is displayed, press
ENTER.

2. The xture will now run a self test.

TEMP - With this function you can check the current tem-

perature of the unit.

1. Press the MENU button until “TEMP” is displayed, press
ENTER.

2. The current temperature of the xture will now be displayed.
Press MENU to exit.

FHRS - With this function you can display the running

time of the xture.

1. Press the MENU button until “FHRS” is displayed, press
ENTER.

2. The running time of the xture will now be displayed. Press
MENU to exit.

Operating Modes: The Sweeper Beam Quad LED can operate in
three different modes. In each mode you can run the fixture as a stand
alone fixture or in a master/slave confiugration. This next section will

detail the differences in the operating modes.

• Sound Active mode -

The fixture will react to sound, chasing through the built-in programs.

• Show mode -

Choose 1 of 12 show modes to run.

• DMX control mode -
This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation® Show
Designer.

™

Master-Slave Operation This function will allow you to link up to 16

units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.

2. Set the Master unit to your desired operating mode, then set the
unit to the Master setting.

3. For the slave units press the MENU button until “SLND” is dis-

played, and Press ENTER. Set the slave units to either “SL 1” or
“SL 2”.

4. The slave units will now follow the Master unit.

VER - With this function you can display the version soft-

ware of the xture.

1. Tap the MENU button until “VER” is displayed, press ENTER.

2. The software version will now be displayed. Press MENU to
exit.

ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 11

Universal DMX Control: This function allows you to use a Elation®

universal DMX-512 controller to control the chases and patterns, dim­mer and strobe. A DMX controller allows you to create unique pro­grams tailored to your individual needs.

1. The Sweeper Beam Quad LED has 4 DMX Channel modes; 2
Channel, 4 Channels, 8 Channels, or 10 Channels. See pages

ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 12

Mega Beam Bar Operation

18-24 for detailed description of the DMX values and traits.

2. To control your fixture in DMX mode, follow the set-up procedures
on pages 6-8 as well as the set-up specifications that are includ­ ed with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instructions on page 10 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.

7. For help operating in DMX mode consult the manual included
with your DMX controller.

Sound Active Mode: This mode allows either single unit or several

units linked together, to run to the beat of the music.

1. Tap the MENU button until “SOUN” is displayed, and press

ENTER.

2. Tap the UP or DOWN buttons to choose either OFF or ON, and

press ENTER, then press and hold MENU for 3 seconds to con­ rm. To adjust sound sensitivity see page 9.

3. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout.

Show Mode: In this mode you can choose 1 of 12 show modes to

run.

1. Tap the MENU button until “SHND” is displayed, and press

ENTER.

2. Tap the UP or DOWN buttons until you nd your desired show,

and press ENTER then press and hold MENU for 3 seconds to
con rm. See page 8 for more info.

3. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout.

Mega Beam Bar 2 Channel Mode

Channel Value Function

1 MASTER DIMMER

0 - 255 0% - 100%
2 STROBING
1 - 15 NO FUNCTION
16 - 131 STROBING SLOW - FAST
132 - 139 NO FUNCTION
140 - 181 SLOW OPEN - FAST CLOSE
182 - 189 NO FUNCTION
190 - 231 SLOW CLOSE - FAST OPEN
232 - 239 NO FUNCTION
240 - 247 SOUND ACTIVE STROBING
248 - 255 NO FUNCTION

Mega Beam Bar 4 Channel Mode

Channel Value Function

1 RED LEDS 1-4

0 - 255 0% - 100%
2 GREEN LEDS 1-4
0 - 255 0% - 100%
3 BLUE LEDS 1-4
0 - 255 0% - 100%
4 WHITE LEDS 1-4
0 - 255 0% - 100%

Mega Beam Bar UC3 Control

Stand By Blackout the fixture

Function Synchronous strobe in white led full on

Random strobe in white led full on by sound active

Mode Strobe (LED OFF) Show (LED ON)

ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 13 ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 14

Select Show1-12

Mega Beam Bar 8 Channel Mode

Channel Value Function

Mega Beam Bar 10 Channel Mode

Channel Value Function

1 RED LEDS 1-2

0 - 255 0% - 100%
2 GREEN LEDS 1-2
0 - 255 0% - 100%
3 BLUE LEDS 1-2
0 - 255 0% - 100%
4 WHITE LEDS 1-2
0 - 255 0% - 100%
5 RED LEDS 3-4
0 - 255 0% - 100%
6 GREEN LEDS 3-4
0 - 255 0% - 100%
7 BLUE LEDS 3-4
0 - 255 0% - 100%
8 WHITE LEDS 3-4
0 - 255 0% - 100%

1 RED LEDS 1-2
0 - 255 0% - 100%
2 GREEN LEDS 1-2
0 - 255 0% - 100%
3 BLUE LEDS 1-2
0 - 255 0% - 100%
4 WHITE LEDS 1-2
0 - 255 0% - 100%
5 RED LEDS 3-4
0 - 255 0% - 100%
6 GREEN LEDS 3-4
0 - 255 0% - 100%
7 BLUE LEDS 3-4
0 - 255 0% - 100%
8 WHITE LEDS 3-4
0 - 255 0% - 100%
9 MASTER DIMMER
0 - 255 0% - 100%
10 STROBING
1 - 15 NO FUNCTION
16 - 131 STROBING SLOW - FAST
132 - 139 NO FUNCTION
140 - 181 SLOW OPEN - FAST CLOSE
182 - 189 NO FUNCTION
190 - 231 SLOW CLOSE - FAST OPEN
232 - 239 NO FUNCTION
240 - 247 SOUND ACTIVE STROBING
248 - 255 NO FUNCTION

ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 15 ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 16

Mega Beam Bar Fuse Replacement

With this feature you can connect the xtures to one another

using the IEC input and output sockets. The quantity that can be

connected is 7 xtures maximum. After 7 xtures you will need to
use a new power outlet. They must be the same xtures. DO NOT
mix xtures.

Mega Beam Bar Fuse Replacement

Disconnect the unit from its power source. Remove the power cord
from the unit. Once the cord has been removed, you will find that the

fuse holder is located inside the power socket. Insert a flat-head screw

driver into the power socket and gently pry out the fuse holder. Remove

the bad fuse and replace with a new one. The fuse holder also has a
holder for a spare fuse.

Mega Beam Bar Trouble Shooting

Listed below are a few common problems the user may encounter,
with solutions.

Unit not responding to DMX:

1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs

and outputs are connected.

Unit does not respond to sound:

1. Quiet or high pitched sounds will not activate the unit.

2. Make sure that Sound Active mode is activated.

Mega Beam Bar Cleaning

Due to fog residue, smoke, and dust cleaning the internal and exter­nal optical lenses must be carried out periodically to optimize light
output.

1. Use normal glass cleaner and a soft cloth to wipe down the

outside casing.

2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.

3. Always be sure to dry all parts completely before plugging

the unit back in.

Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).

ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 17 ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 18

Mega Beam Bar Warranty

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#)

before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All

shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

 •LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)

 •LaserProducts=90-DayLimitedWarranty
 •L.E.D.Products=3-year(1095days)LimitedWarranty(excluding motors, PCB boards, and power

supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty). Only the L.E.D.s carry a 3-year warranty

Mega Beam Bar Specifications

Model:

Voltage: 100V ~ 240V 50/60Hz
LEDs: 16 x 3W LED’s (4 Red, 4 Green,
4 Blue, & 4 White)
Beam Angle: 13.5 Degrees
Power Consumption: 49W
Power Cord Daisy Chain: 7 Fixtures Max.
Fuse: 6.3 Amp
Weight: 15lbs./ 6.7Kgs.
Dimensions: 35.25” (L) x 5.5” (W) x 6.25” (H)
894 x 135 x 158mm
Colors: RGB
DMX Channels: 4 DMX Modes: 2 Channel Mode,
4 Channel Mode, 8 Channel Mode,
8 Channel Mode, & 10 Channel

Mode

Working Position: Any safe working position
Warranty: 3 Year (1,095 days)

Mega Beam Bar

Auto Sensing Voltage: This xture contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged
into the power source.

Please Note: Specications and improvements in the design of

this unit and this manual are subject to change without any prior
written notice.

ADJ Products, LLC - www.adj.com - Mega Beam Bar User Manual Page 19

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: [phone] / Fax: [phone]

Web: www.adj.com / E-mail: [e-mail]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

[e-mail] / www.adj.com

Tel: [phone] / Fax: [phone]