ADJ Encore Burst 200 User guide

ENCORE BURST 200™

user manual

©2019 ADJ all rights reserved. Information, specifications, diagrams, images, and

Date

Document

Version

Software

Version ≥

DMX

Channel Modes

Notes

07/25/18

1.2

1.2

1 / 2 / 3/ 4 / 6

Updated release.

11/6/18

1.4

1.3

1 / 2 / 2A / 3 / 4 / 6

Added DMX Channel Mode 2A, Gamma
Brightness setting 2.6.

03/22/19

1.6

N/C

NO CHANGE

Updated Installation Instructions.

04/10/19

1.8

N/C

NO CHANGE

Added dimensional drawings for yoke.

07/16/19

1.9

N/C

NO CHANGE

Updated safety cable installation image.

instructions herein are subject to change without notice. ADJ logo and identifying product
names and numbers herein are trademarks of ADJ. Copyright protection claimed includes
all forms and matters of copyrightable materials and information now allowed by statutory
or judicial law or hereinafter granted. Product names used in this document may be
trademarks or registered trademarks of their respective companies and are hereby
acknowledged. All non-ELATION brands and product names are trademarks or registered
trademarks of their respective companies.

ADJ and all affiliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect
economic loss associated with the use or reliance of any information contained within this
document, and/or as a result of the improper, unsafe, insufficient and negligent assembly,
installation, rigging, and operation of this product.

ADJ USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040
323-582-2650 | 323-532-2941 fax | www.adj.com | [e-mail]

ADJ Supply Europe B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands
[phone] | [phone] fax | www.americandj.eu | [e-mail]

ADJ Mexico | AV Santa Ana 30 | Parque Industrial Lerma, Lerma, Mexico 52000
[phone]

DOCUMENT VERSION

Due to additional product features and/or enhancements,
an updated version of this document may be available
online. Please check www.adj.com for the latest
revision/update of this manual, before beginning
installation and/or programming.

2

CONTENTS

General Information

4

Limited Warranty (USA Only)

5

Safety Guidelines

6

Maintenance Guidelines

8

Fixture Overview

9

Installation Guidelines

10

System Menu

18

DMX Channel Functions and Values

23

Specifications

24

3

GENERAL INFORMATION

INTRODUCTION

This fixture has been designed to perform reliably for years when the information in this
manual are followed. Please read and understand all the instructions and guidelines
carefully and thoroughly before operating this unit. This manual contains important
information regarding safety, installation, use, and maintenance.

UNPACKING

Each fixture has been thoroughly tested and shipped in perfect operating condition.
Carefully check the outer shipping carton for signs of any damage that may have occurred
during shipping. If the outer carton appears to be damaged, carefully inspect the fixture for
damage and be sure all included accessories have arrived intact. In the event damage has
been found and/or parts are missing, please contact our customer support team for further
instructions. Please do NOT return this fixture to your dealer without first contacting
customer support at the number listed below. Please do NOT discard the outer shipping
carton in the trash. Please recycle whenever possible.

CUSTOMER SUPPORT

Contact ADJ Service for any product related service and support needs.
Please visit forums.adj.com with questions, comments or suggestions.

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

800-322-6337 | Fax [phone] | [e-mail]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

[phone] | Fax [phone] | [e-mail]

REPLACEMENT PARTS please visit parts.americandj.com

WARRANTY RETURNS

All returned service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number must be clearly written
on the outside of the return package. A brief description of the problem as well as the R.A.
number must also be written down on a piece of paper and included in the shipping
container. If the unit is under warranty, you must provide a copy of your proof of purchase
invoice. Items returned without a R.A. number clearly marked on the outside of the package
will be refused and returned at customer’s expense. You may obtain a R.A. number by
contacting customer support.

4

LIMITED WARRANTY (USA ONLY)

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of
manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see
specific warranty periods below). This warranty shall be valid only if the product is purchased within the
United States of America, including possessions and territories. It is the owner’s responsibility to establish the
date and place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the
product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to
the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or service
(including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping
charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped
in its original package. No accessories should be shipped with the product. If any accessories are shipped
with the product, ADJ Products, LLC shall have no liability whatsoever for loss of or damage to any such
accessories, or for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because not
properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic
checkup. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of
defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be
limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of ADJ
Products, LLC. All products covered by this warranty were manufactured after August 15, 2012, and bear
identifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured. No warranty,
whether expressed or implied, is given or made with respect to any accessory supplied with products
described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ
Products, LLC in connection with this product, including warranties of merchantability or fitness, are limited in
duration to the warranty period set forth above. And no warranties, whether expressed or implied, including
warranties of merchantability or fitness, shall apply to this product after said period has expired. The
consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above;
and under no circumstances shall ADJ Products, LLC be liable for any loss or damage, direct or
consequential, arising out of the use of, or inability to use, this product. This warranty is the only written
warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties and written
descriptions of warranty terms and conditions heretofore published.

LIMITED WARRANTY PERIODS

Non-LED Lighting Products = 1-Ye ar (3 65 D ay s) (Including Special Effect Lighting, Intelligent Lighting, UV lighting,
Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands, Power/Data Distribution, etc.
excluding LED and lamps)

Laser Products = 1-Yea r ( 36 5 Da ys ) (excluding laser diodes which have a 6-Month Limited Warranty)

LED Products = 2-Ye ar (7 3 0 D ay s) (excluding batteries which have a 180 Day Limited Warranty)

NOTE: 2-Ye ar (7 3 0 D ays) Limited Warranty ONLY applies to product purchased within the USA.

StarTec Series = 1-Ye ar ( 3 65 Da y s) (excluding batteries which have a 180 Day Limited Warranty)

ADJ DMX Controllers = 2 Year (730 Days)

American Audio Products = 1 Year (365 Days)

5

SAFETY GUIDELINES

PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.
DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID
YOUR MANUFACTURES WARRANTY. DAMAGES RESULTING FROM
MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF
SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID
THE MANUFACTURES WARRANTY AND ARE NOT SUBJECT TO ANY
WARRANTY CLAIMS AND/OR REPAIRS.

DO NOT PLUG FIXTURE INTO A DIMMER PACK!
NEVER OPEN THIS FIXTURE WHILE IN USE!
UNPLUG POWER BEFORE SERVICING FIXTURE!
NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!
KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!

NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
RETINA INJURY RISK - MAY INDUCE BLINDNESS!

SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

MAXIMUM TEMPERATURE OF EXTERNAL SURFACE 185°F (85°C)

MAXIMUM AMBIENT TEMPERATURE IS Ta: 104°F (40°C)

This fixture is a sophisticated piece of electronic equipment. To guarantee a smooth
operation, it is important to follow all instructions and guidelines in this manual. ADJ is not
responsible for injury and/or damages resulting from the misuse of this fixture due to the
disregard of the information printed in this manual. Only qualified and/or certified personnel
should perform installation of this fixture and only the original rigging parts (omega brackets)
included with this fixture should be used for installation. Any modifications to the fixture
and/or the included mounting hardware will void the original manufactures warranty and
increase the risk of damage and/or personal injury.

6

SAFETY GUIDELINES

DO NOT TOUCH the fixture housing during operation. Turn OFF the power and allow

approximately 15 minutes for the fixture to cool down before serving.

DO NOT shake fixture, avoid brute force when installing and/or operating fixture.

DO NOT operate fixture if the power cord is frayed, crimped, damaged and/or if any of the

power cord connectors are damaged and do not insert into the fixture securely with ease.

NEVER force a power cord connector into the fixture. If the power cord or any of its

connectors are damaged, replace it immediately with a new one of similar power rating.

DO NOT block any air ventilation slots.

All fan and air inlets must remain clean and never blocked.

Allow approx. 6” (15cm) between fixture and a wall for proper cooling.

When installing fixture in a suspended environment, always use mounting hardware that is no

less than M10 x 25 mm, and always install fixture with an appropriately rated safety cable.

Always disconnect fixture from main power source before performing any type of service

and/or cleaning procedure. Only handle the power cord by the plug end, never pull out the

plug by tugging the wire portion of the cord.

During the initial operation of this fixture, a light smoke or smell may emit from the interior of

the fixture. This is a normal process and is caused by excess paint in the interior of the casing

burning off from the heat associated with the lamp and will decrease gradually over time.

Consistent operational breaks will ensure fixture will function properly for many years.

ONLY use the original packaging and materials to transport the fixture in for service.

7

MAINTENANCE GUIDELINES

DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!

CLEANING

Frequent cleaning is recommended to insure proper function, optimized light output, and

an extended life. The frequency of cleaning depends on the environment in which the

fixture operates: damp, smoky or particularly dirty environments can cause greater

accumulation of dirt on the fixture’s optics. Clean the external lens surface at least every 20

days with a soft cloth to avoid dirt/debris accumulation.

NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

Regular inspections are recommended to insure proper function and extended life.

There are no user serviceable parts inside this fixture, please refer all other service issues to

an authorized Elation service technician. Should you need any spare parts, please order

genuine parts from your local Elation dealer.

Please refer to the following points during routine inspections:

A detailed electric check by an approved electrical engineer every three months, to make

sure the circuit contacts are in good condition and prevent overheating.

Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out

during normal operation resulting in damage or injury as larger parts could fall.

Check for any deformations on the housing, color lenses, rigging hardware and rigging

points (ceiling, suspension, trussing). Deformations in the housing could allow for dust to

enter into the fixture. Damaged rigging points or unsecured rigging could cause the fixture

to fall and seriously injure a person(s).

Electric power supply cables must not show any damage, material fatigue or sediments.

NEVER remove the ground prong from the power cable.

8

FIXTURE OVERVIEW

5-Pin DMX In/Out Control Menu LCD Display Power Cable In/Out

Safety Cable

Attachment

INCLUDED ITEMS

Omega Bracket

Yoke Bracket Kit (Updated 03/19)

Power Cable

9

INSTALLATION INSTRUCTIONS

IPX4 RATED

An IP rated lighting fixture is one, which is commonly installed in outdoor environments and
has been designed with an enclosure that effectively protects the ingress (entry) of external
foreign objects such as dust and water. The International Protection (IP) rating system is
commonly expressed as "IP" (Ingress Protection) followed by two numbers (i.e. IP20)
where the numbers define the degree of protection. The first digit (Foreign Bodies
Protection) indicates the extent of protection against particles entering the fixture and the
second digit (Water Protection) indicates the extent of protection against water entering the
fixture.

An IPX4 rated lighting fixture designed for temporary outdoor environments which has NOT
been tested to protect against the ingress of dust (X) but has been tested to protect from
splash of water in any direction (4).

PERMANENT OUTDOOR AND/OR MARINE/COSTAL INSTALLATIONS

Please note although this fixture is IP rated, this fixture is NOT suitable for permanent
outdoor and/or marine environment installations. Installing this fixture in permanent outdoor
and/or marine environment installation may cause corrosion and/or excessive wear to the
interior and/or exterior components of the fixture. Damages and/or performance issues
resulting from installation in a permanent outdoor and/or marine environment installation
will void the manufactures warranty and will NOT be subject to any warranty claims and/or
repairs.

FLAMMABLE MATERIAL WARNING

Keep fixture minimum 5.0 feet (1.5m) away from flammable materials and/or pyrotechnics.

ELECTRICAL CONNECTIONS

A qualified electrician should be used for all electrical connections and/or installations.

ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A
NON-CONDUCTIVE DIELECTRIC GREASE (AVAILABLE AT MOST ELECTRICAL
SUPPLIERS) TO PREVENT WATER INGRESS/CONDENSATION AND/OR
CORROSION.

USE CAUTION WHEN POWER LINKING OTHER MODEL FIXTURES AS THE
POWER CONSUMPTION OF OTHER MODEL FIXTURES MAY EXCEED THE MAX
POWER OUTPUT ON THIS FIXTURE. CHECK SILK SCREEN FOR MAX AMPS.

10

INSTALLATION INSTRUCTIONS

SEAL ALL UNUSED

CONNECTION CAPS

SAFETY CABLE

AT TA C H ME NT

DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!

Fixture MUST be installed following all local, national, and country commercial electrical
and construction codes and regulations.
Before rigging/mounting a single fixture or multiple interconnected fixtures for custom
matrix designs to any metal truss/structure or placing the fixture(s) on any surface, a
professional equipment installer MUST be consulted to determine if the metal
truss/structure or surface is properly certified to safely hold the combined weight of the
fixture(s), clamps, cables, and accessories.
Maximum ambient operating temperature is 104°F. (40°C)
Fixture(s) should be installed in areas outside walking paths, seating areas, or away from
areas were unauthorized personnel might reach the fixture by hand.
NEVER stand directly below the fixture(s) when rigging, removing or servicing.
Overhead fixture installation must always be secured with a secondary safety attachment,
such as an appropriately rated safety cable that can hold 10 times the weight of the fixture.
Allow approximately 15 minutes for the fixture to cool down before serving.

TO MAINTAIN IP RATING INTEGRITY, ALL UNUSED CONNECTION RUBBER
CAPS MUST BE SEALED.

11

INSTALLATION INSTRUCTIONS

OVERHEAD RIGGING

Overhead rigging requires extensive experience, including amongst others calculating
working load limits, installation material being used, and periodic safety inspection of all
installation material and the fixture. If you lack these qualifications, DO NOT attempt the
installation yourself. Improper installation can result in bodily injury and property damage.

OMEGA BRACKET

The included Omega Bracket can be attached to any of the 4 sides of the fixture, the top or
bottom longer edges, or the left or right shorter edges. The best edge to attach the bracket
to will depend on desired installation look. Follow the installation steps below.

OMEGA BRACKET MUST BE USED WHEN CONNECTING FIXTURES TOGETHER!

1. Attach the Omega Bracket to the fixture using 2 of the 4 included interlocking pins.

2. To remove the interlocking pins, push the spring-loaded pin in and turn clockwise or
counter-clockwise until it releases from the fixture.

3. Slide the bracket into the fixture aligning holes of the bracket to the holes on the fixture.

4. Insert 2 interlocking pins into the fixture holes, making sure the pins go completely
through the fixture and into the bracket. With the pins completely inserted, push the pins
towards the fixture and turn clockwise or counter-clockwise to lock into place.

5. Confirm both pins and the bracket are secure before mounting the fixture with an
appropriately rated professional grade rigging clamp.

12

INSTALLATION INSTRUCTIONS

YOKE BRACKET KIT (Updated 03/19)

The included Yoke Bracket Kit can be attached to the fixture using the included hardware.
Follow the installation steps below.

YOKE BRACKET FOR SINGLE FIXURE INSTALLATION ONLY! DO NOT USE WHEN

CONNECTING MULTIPLE FIXTURES TOGETHER!

1. Attach the Yoke Bracket to the fixture using the included hardware.

2. Adjust the bracket into the designed position then tighten adjustment knobs securely.

3. Mount the fixture with an appropriately rated professional grade rigging clamp.

13

INSTALLATION INSTRUCTIONS

CONNECTING FIXTURES TOGETHER

The fixture includes a unique interlocking system which allows multiple fixtures to be
connected together vertically and horizontally, using the included 4 spring-loaded
interlocking pins on each fixture. Follow the installation steps below.

OMEGA BRACKET MUST BE USED WHEN CONNECTING FIXTURES TOGETHER!

1. Attach the Omega Bracket to the first fixture as described on the previous page.

2. To attach a fixture vertically, slide fixtures together aligning the holes on both fixtures.

3. Insert interlocking pins into the fixture holes, pushing pins completely through and
turning clockwise or counter-clockwise to lock into place.

4. Repeat steps 2 and 3 to attach additional fixtures vertically.

5. To attach a fixture horizontally, push out the spring-loaded bracket on the top and
bottom edges of each fixture, then slide fixtures together aligning the holes on both
spring-loaded brackets on both fixtures.

6. Insert interlocking pins into the fixture holes, pushing pins completely through and
turning clockwise or counter-clockwise to lock into place.

7. Repeat steps 5 and 6 to attach additional fixtures horizontally.

8. Confirm Omega Bracket on top fixture and all interlocking pins on all vertically connected
fixtures are secure before mounting a vertical matrix of fixtures with an appropriately rated
professional grade rigging clamp. For horizontally connected fixtures, each fixture must be
mounted with its own appropriately rated professional grade rigging clamp.

14

INSTALLATION INSTRUCTIONS

MAXIMUM NUMBER OF CONNECTING FIXTURES VERTICALLY / HORIZONTALLY = 10

Each set of 10 fixtures must be attached to a structure which can support 10x the total
weight of the 10 fixtures and the first fixture in the chain must be attached to the structure
using the Omega Bracket and an appropriately rated professional grade rigging clamp.

OMEGA BRACKET MUST BE USED WHEN CONNECTING FIXTURES TOGETHER!

15

INSTALLATION INSTRUCTIONS

SAFETY CABLES

Each fixture includes a Safety Cable attachment loop on the back. All fixtures installed
overhead MUST always be secured with its own dedicated secondary safety attachment,
such as an appropriately rated safety cable that can hold 10 times the weight of the fixture.

ALWAYS ATTACH AN INDEPENDENT SAFETY CABLE BETWEEN TRUSS/STRUCTURE AND THE FIXTURE
WHENEVER INSTALLING THE FIXTURE IN A SUSPENDED ENVIRONMENT TO ENSURE FIXTURE WILL
NOT DROP IF CLAMP OR INTERLOCKING PINS FAIL!

NEVER DAISYCHAIN MUTIPLE SAFETY CABLES TOGETHER BETWEEN MULTIPLE FIXTURES!
EACH FIXTURE MUST HAVE ITS OWN INDEPENDENT SAFETY CABLE! (SEE IMAGES BELOW)

16

INSTALLATION INSTRUCTIONS

ADJUSTING LED LENS POSITION DEGREE

The LED lens position can easily be adjusted manually from the default 0-degree position,
to 7.5+ or 15+ degrees (UP) and -7.5 and -15.0 degrees (DOWN). Simply push the LED lens
array by hand either UP or DOWN into the desired angle. The LED lens array movement can
be adjusted by loosening or tightening the small screw on the side of the fixture using a
matching size hex key (not included).

17

SYSTEM MENU

The fixture includes an easy to navigate system menu where fixture settings can be
adjusted via the LCD control panel located on the back of the fixture. (see image below)
To access the system menu press and hold the MENU button for 3 seconds. The LCD Menu
Control Display will shut OFF automatically about 1 minute from the last button press.

18

SYSTEM MENU CHANGE WITH SOFTWARE UPDATE VERSION ≥1.3

2ACh Channel Mode Added

19

SYSTEM MENU CHANGE WITH SOFTWARE UPDATE VERSION ≥1.3

2.6 Gamma Correction Setting Added

20

21

DIMMING CURVE

The fixture includes 6 different dimming curve modes which can selected from either the

system menu or via DMX. The graph below provides details on each dimming curve mode.

22

DMX CHANNEL FUNCTIONS AND VALUES

Supports Software Versions: ≥ 1.3

Features subject to change without any prior written notice.

*Pixel control of effects depends on fixture orientation.

MODE / CHANNEL

VALUE

FUNCTION

1CH

2CH

2ACH

3CH

4CH

6CH

1 1 1 1

MASTER DIMMER - LEFT & RIGHT PIXELS

0-255

0-100%

2 2 2

DIMMER FINE (16-BIT) - LEFT & RIGHT PIXELS

0-256

16-bit FINE Adjustment

1

1

MASTER DIMMER - LEFT PIXEL

0-255

0-100%

2

2

MASTER DIMMER - RIGHT PIXEL

0-255

0-100%

4

MASTER DIMMER / INTENSITY

0-255

Dimmer (0-100%)

5

MASTER DIMMER / INTENSITY FINE

0-255

Dimmer (0-100%)

3

3

SHUTTER / STROBE

0-31

LED OFF

32-63

LED ON

64-95

Strobe Effect SLOW to FAST

96-127

LED ON

128-159

Strobe Pulse Effect In Sequences SLOW to FAST

160-191

LED ON

192-223

Random Strobe Effect SLOW to FAST

224-255

LED ON

3 4

6

DIMMING MODES

0-20

STANDARD

21-40

STAGE

41-60

TV

61-80

ARCHITECTURAL

81-100

THEATER

101-120

STAGE 2

121-255

DEFAULT TO UNIT SETTING

DMX CHANGE WITH SOFTWARE UPDATE VERSION ≥1.3

See highlighted items below which have been updated with this software update.

23

SPECIFICATIONS

Voltage: 100-240V / 50/60Hz
LEDs: x2 110W CREE COB LEDs
Color Temperature: 2700K (1200K Tungsten Mode)
IP Rating: IPX4
Working Position: Any Safe Working Position
Power Draw: 235W
Power Linking: 4 Fixtures Max @120V | 8 Fixtures Max @240V
Fuse: 1A
DMX Channels: 6 DMX Channel Modes 1 / 2 / 2A / 3 / 4 / 6
Connections: 5pin DMX and powerCON TRUE1 In/Out
Weight: 15 lbs. (6.8kg)
Dimensions (LxWxH): 15.7” (400mm) x 7.9” (200.5mm) x 8.5” (215.5mm)
Dimensions w/Bracket (LxWxH): 15.7” (400mm) x 7.9” (200.5mm) x 10.4” (264mm)
Dimensions w/Yoke (LxWxH): 19.8” (503mm) x 7.9” (200.5mm) x 12.8” (325.3mm)
Warranty: 2 Years (730 Days)

Specifications and improvements in the design of this unit and this manual are subject to change without notice.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device uses and can radiate radio frequency energy and, if not installed and used in accordance with the
included instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by turning the device off and on, the user
is encouraged to try to correct the interference by one or more of the following methods:

• Reorient or relocate the device.

• Increase the separation between the device and the receiver.

• Connect the device to an electrical outlet on a circuit different from which the radio receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

24

DIMENSIONAL DRAWINGS

264

Specifications and improvements in the design of this unit and this manual are subject to change without notice.

25

DIMENSIONAL DRAWINGS

26

(page left blank)

27