Adj Accu Fog 1000 User Manual [ru]
American DJ®
Accu Fog 1000
Table of Contents
Unpacking......................................................................3
Introduction....................................................................3
Customer Support......................................................................3
Safety Precautions......................................................................4
Handling Precautions..................................................................5
Registration......................................................................5
Features.........................................................................6
Set-Up.............................................................................7
System Menu............................................................................10
Editing Program.........................................................................24
Error Codes...............................................................................29
Operating Modes.......................................................................31
DMX Traits.................................................................................33
Fuse Replacement....................................................................36
Cleaning.......... ....................... ....................... ..........36
Trouble Shooting.......................................................................36
Warran ty.... ..... .............. ..... ..... ..... ................... ..... ...37
Specifications....................................................................39
Caution: Fog Machines may set off Smoke Alarms!
User Instructions
4295 Charter Street
Los Angeles CA. 90058
Rev. 5/07
www.americandj.com
American DJ®
American DJ® - www.americandj.com - Accu Fog 1000 Instruction Manual Page 2
Accu Fog 1000 General Information Accu Fog 1000 Safety Precautions
Unpacking: Thank you for purchasing the Accu Fog 1000 by Ameri-
can DJ®. Every Accu Fog 1000 has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your xture for any
damage and be sure all equipment necessary to operate the unit has
arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Please do not return this unit to your dealer without con-
tacting customer support rst.
Introduction: The Accu Fog 1000 is a 5 or 7 DMX channel (depend-
ing on the mode you are in), moving head, intelligent DMX fog machine.
The fixture can operate in three different operating modes; stand alone,
sound-active, or in a Master/Slave configuration. The Accu Fog 1000
also has an auto mode that can be used, while operating as a stand
alone unit or when used in multiples linked in a master/slave configuration.
Customer Support: American DJ® provides a toll free customer
support line, to provide help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 9:00 a.m. to 5:
00 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
SAFETY ISSUES:
NEVER POINT OR AIM A FOG MACHINE TOWARDS PEOPLE OR
THEIR CLOTHING. THIS UNIT EMITS HOT VAPOR AND SHOULD
BE USED WITH THE SAME CARE THAT YOU WOULD OBSERVE
WHEN USING AN ELECTRIC KETTLE OR IRON.
• Be sure to save the packing carton in the unlikely event the unit
may have to be returned for service
• Do not spill water or other liquids into or on to your fogger. Be
sure that all the fog uid is kept inside the uid reservoir
• Be sure that the local power outlet match that or the required
voltage for your fog machine
• Do not remove the top cover under any conditions. There are no
user serviceable parts inside
• Disconnect the unit’s main power when left unused for long peri ods of time
• Never connect this unit to a dimmer pack
• Do not attempt to operate this unit, if it becomes damaged in anyway
• Never operate this unit when it’s cover is removed
• To reduce the risk of electrical shock or re, do not expose this
unit rain or moisture
• Do not attempt to operate this unit if the power cord has been fray ed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the
risk of electrical shock and re in case of an internal short
• Disconnect from main power before making any type of connection
• Never block the ventilation holes. Always be sure to mount this
unit in an area that will allow proper ventilation. Allow about 6”
(15cm) between this device and a wall
• This unit is intended for indoor use only, use of this product out doors voids all warranties
• Always mount this unit in a safe and stable matter
• Please route your power cord out of the way of foot trafc. Power
cords should be routed so they are not likely to be walked on,
pinched by items placed upon or against them
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 36 for cleaning details
• The unit should only be serviced by qualified service personnel
when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain or water.
D. The appliance does not appear to operate normally or
exhibits a marked change in performance.
American DJ® - www.americandj.com - Accu Fog 1000 Instruction Manual Page 4American DJ® - www.americandj.com - Accu Fog 1000 Instruction Manual Page 3
Accu Fog 1000 General Instructions
Accu Fog 1000 Features
To optimize the performance of this product, please read these operating
instructions carefully to familiarize yourself with the basic operations of
this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with
the unit, for future reference.
Accu Fog 1000 Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact American DJ®.
During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.
American DJ® will not accept any liability for any resulting damages
caused by the non-observance of this manual or any unauthorized
modication to this unit.
Accu Fog 1000 Product Registration
The Accu Fog 1000 carries a one year limited warranty. Please fill out
the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper and included in the shipping carton.
If the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our toll free customer support number. All
packages returned to the service department not displaying a R.A.
number on the outside of the package will be returned to the shipper
at the shippers cost.
• 3 Operating Modes - 5 or 7 DMX Channel Mode, Master/Slave
Sound Active Mode; Stand Alone Sound Active Mode
• Internal Microphone
• 360˚ Pan Movement
• 265˚ Tilt Movement
• Digital Display for Address and Function Setting
• 1 Liter Removable, Rotating Tank Holder
• 1 Gallon Fog Fluid Container Holder (Optional, Sold Separately)
• Thermal Cut-Off Mechanism: Auto shutdown feature protects
pump system when fog fluid get to low
• Electronic Thermo Sensing (ETS): Now warm-uo time between fog
blasts
• RDMX Remote DMX Addressing: Change the DMX address using
a DMX controller
• Smart Sense: Units automatically recognize if they are in DMX or
Master/Slave mode
Accu Fog 1000 Thermal Cut-Off Feature
The new Accu Fog 1000 fog machines features a fog juice level sensor. When the fog juice level reaches a low level, a built-in sensor will
automatically shut off the pump. This will greatly expand the life of
the pump.
American DJ® - www.americandj.com - Accu Fog 1000 Instruction Manual Page 5
American DJ® - www.americandj.com - Accu Fog 1000 Instruction Manual Page 6
Accu Fog 1000 Set Up
DMX512 IN
3-PIN XLR
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Terminatio n re duces signal errors and
avo ids signal tran smis sion problem s
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the l ast fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
1
2
3
Terminatio n re duces signal errors and
avo ids signal tran smis sion problem s
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the l ast fixture.
Accu Fog 1000 Set Up
Power Supply: Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your American DJ®
Accu Fog 1000. The American DJ® Accu Fog 1000 is available in a
120v and 220v version. Because line voltage may vary from venue to
venue, you should be sure your unit voltage matches the wall outlet
voltage before attempting to operate you xture. Also be sure to only
use the included I.E.C. power cable supplied with the unit, this cable
matches the voltage and current requirements of the unit.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX
and Master/Slave Operation): The Accu Fog 1000
can be controlled via DMX-512 protocol. The Accu
Fog 1000 is a ve and a seven channel DMX unit,
depending on what mode you are in. The DMX
address is set electronically using the controls on
the side panel of the unit. Your unit and your DMX
controller require a standard 3-pin XLR connector for data input and
data output (Figure 1). If you are making your own cables, be sure
Figure 1
American DJ® - www.americandj.com - Accu Fog 1000 Instruction Manual Page 7
to use standard two conductor shielded cable (This cable may be
purchased at almost all professional sound and lighting stores). Your
cables should be made with a male and female XLR connector on
either end of the cable. Also remember that DMX cable must be daisy
chained and cannot be split.
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
Figure 2
XLR Male Socket
1 Ground
2 Cold
3 Hot
Figure 3
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
American DJ® - www.americandj.com - Accu Fog 1000 Instruction Manual Page 8
XLR Female Socket
2 Cold
XLR Pin Conguration
1 Ground
3 Hot
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
Accu Fog 1000 Set Up
0
ADDR
AXXX
A001
Indicate the staring DMX
address
A001 also is the setting for
slave
1
TEST
T-01~T-XX
Automatically test the function
RUN
MSTR/ALON
Runs fixture as “master” or
“alone” for auto
AUDI
MSTR/ALON
Runs fixture as “master” or
“alone” for audio
2
PLAY
AUTO
OFF / RUN /AUDI
Runs fixture for no DMX
3
HEAT
ON/OFF
Manually switches heater “on”
and “off”
ALL
Reset all motors and returns
fixture to home
4
RESE
SCAN
Reset only motors for pan/tilt
LIFE
0000~9999
Displays the total fixture
running time
HEAT
0000~9999
Displays a heater running time
5
TIME
CLMP
Clear heater running time
6
RPAN
ON/OFF
Reverses the pan movements
7
RTLT
ON/OFF
Reverses the tilt movements
8
MIC
M-XX M-70
Mic sensitivity
VALU
D–XX D-00 (DXXX)
Display the DMX512 value of
each channel
D ON
ON/OFF
Display turn off after 2mins
9
DISP
FLIP
ON/OFF
This function will reverse the
display 180
LAAU
ON/OFF
Automatic heater start with
power
RDMX
ON/OFF
Change DMX address via
external controller
MODE
5CH/7CH/
Channel mode select
DLOF
ON/OFF
Switch heater via DMX
DFSE
ON/OFF
Resets all the fixture functions
to default
FEED
ON/OFF
Pan/tilt feedback (error
correction) on/off
10
SPEC
VER
V1.0~V9.9
Software version
STEP
S–01 ~S–48
Set the amount of your
program
C–01~C–30
0 1
XX(00~FFH)
3 0
XX(00~FFH)
Edit the channels of
each scene
TIME
T
XXX(001~999)
Time for each scene
SCXX
CEDT
ON/OFF
Edit program via
controller
REC.
RE.XX
Auto Save
11
EDIT
RUN
ON/OFF
Program test
Accu Fog 1000 System Menu
5-Pin XLR DMX Connectors.
connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
American DJ® - www.americandj.com - Accu Fog 1000 Instruction Manual Page 9
Some manufactures use 5-pin XLR
3-Pin XLR to 5-Pin XLR Conversion
Pin 1
Pin 2
Pin 3
Pin 4 - Do Not Use
Pin 5 - Do Not Use
Pin 1
Pin 2
Pin 3
American DJ® - www.americandj.com - Accu Fog 1000 Instruction Manual Page 10
Accu Fog 1000 System Menu
Accu Fog 1000 System Menu
ADDRESS MENU -
AOO1 - A511 (Value) - This is where you set the DMX address of
the unit.
TEST MENU -
T-01 - T-XX (Test) - Tests the functions of each channel.
PLAY MENU -
RUN - Runs the unit as a “master” in master/slave conguration
or, in a stand alone mode. The unit will run in auto mode.
AUDI (Audio) - Runs the unit as a “master” in master/slave con-
guration, or in a stand alone. The unit will run in sound active
mode.
AUTO - Runs the internal program.
RESE (RESET) MENU -
ALL - Resets all the motors in the unit.
SCAN - Resets the motors that control pan/tilt.
TIME MENU -
LIFE - Displays the xtures total running time.
HEAT - Displays the heater running time.
CLMP - Clears the heater running time.
RPAN (REVERSE PAN) MENU -
ON/OFF - When “On” is chosen it will reverse the pan.
RTILT (REVERSE TILT) MENU -
ON/OFF - When “On” is chosen it will reverse the tilt.
DISPLAY MENU -
VALU (DMX-512 Value) - Display the DMX-512 value of each
channel.
D ON - Turns digital display off after 2 minutes.
FLIP - “Flips” the digital display 180º.
SPEC MENU -
LAAU - Automatically starts the heater when power is applied.
RDMX - Lets you adjust the DMX address via external controller.
MODE - 5Ch/7Ch With this function you can switch between 5
channels and 7 channels. See page 33 for the 5 Channel DMX
traits, and 34-35 for 7 Channel DMX traits.
DLOF - This lets you switch the heater on via DMX.
DFSE (Default Settings) - Resets the unit to the default settings.
FEED - Turns the Pan/Tilt feedback (error correction) on/off
VER (Version) - Displays the software version
EDIT MENU -
STEP (S-01 - S-48) - These are the steps slots that you write
your programs into. There are at total of 48 steps. See edit program, page 25.
SCXX (SC01 - SC30) - These are the scenes that are stored in
your program. There are a total of 30 scenes.
REC - This will auto save your custom program.
RUN - This will run your custom program.
MIC MENU -
MIC - With this function you can make the internal mic more or
less sensitive to sound.
American DJ® - www.americandj.com - Accu Fog 1000 Instruction Manual Page 12American DJ® - www.americandj.com - Accu Fog 1000 Instruction Manual Page 11
Loading...