FOCUS SPOT 4Z
FOCUS SPOT 4Z PEARL
User Instructions
©2018 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and
with the included instructions, may cause harmful interference to radio communications. However, there is
instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of
their respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This device uses and can radiate radio frequency energy and, if not installed and used in accordance
no guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the following methods:
· Reorient or relocate the device.
· Increase the separation between the device and the receiver.
· Connect the device to an electrical outlet on a circuit different from which the radio receiver is
connected.
· Consult the dealer or an experienced radio/TV technician for help.
DOCUMENT VERSION
Please check www.adj.com for the latest revision/update of this guide.
Date
12/27/18
Document
Version
1
Software
Version
1.04
>
DMX
Channel
Modes
16/18/22
Notes
Initial Release
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Focus Spot 4Z/Focus Spot 4Z Pearl Table of Contents
Introduction
Features I Warranty Registration I Installation
Safety Precautions
Installation
Overview
DMX Set Up
DMX Addressing
DMX Channel Modes & Values
System Menu
Operating Instructions
Master-Slave Set Up
3
4
5
7
9
10
12
13
16
18
27
Dimmer Curve Chart
Dimensional Drawings
Gobo Replacement & Gobos
Fuse Replacement I Multiple Unit Power Linking
Trouble Shooting I Cleaning
Warranty
Technical Specications
28
29
30
31
21
32
33
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 2
Focus Spot 4Z/Focus Spot 4Z Pearl Introduction
Unpacking: Thank you for purchasing the Focus Spot 4Z/Focus Spot 4Z Pearl by ADJ Products, LLC.
Every unit has been thoroughly tested and has been shipped in perfect operating condition. Carefully
check the shipping carton for damage that may have occurred during shipping. If the carton appears
to be damaged, carefully inspect your xture for any damage and be sure all accessories necessary
to operate the unit has arrived intact. In the case damage has been found or parts are missing, please
contact our toll free customer support number for further instructions. Do not return this unit to your
dealer without rst contacting customer support.
Introduction: The Focus Spot 4Z/Focus Spot 4Z Pearl is a DMX intelligent, moviing head,
LED fixture. This xture can be used in a stand alone mode or connected in a Master/Slave conguration. The fixture comes equipped with motorized focus and zoom, 6 different dimming
options The Focus Spot 4Z/Focus Spot 4Z Pearl has 3 DMX channel modes; 16, 18, & 22.
This product is intended to be used by professionally trained personnel only and is not suitable for
private use.
Customer Support: Contact ADJ Service for any product related service and support needs. Also visit
forums.adj.com with questions, comments or suggestions.
Parts: To purchase parts online visit http://parts.americandj.com
ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 | Fax: 323-832-2941 | support@adj.com
ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | support@adj.eu
ADJ PRODUCTS LLC USA
6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com
ADJ SUPPLY Europe B.V
Junostraat 2 6468 EW Kerkrade, The Netherlands
+31 (0)45 546 85 00 | Fax +31 45 546 85 99
www.adj.eu | info@americandj.eu
ADJ PRODUCTS GROUP Mexico
AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000
+52 (728) 282-7070
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufactures warranty. In the unlikely event your unit may require service
please contact ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 3
Focus Spot 4Z/Focus Spot 4Z Pearl Features
• Individual Color and Gobo Wheels
• 8 Colors + White
• 6 Rotating Replaceable Gobos + Open
• Electronic Dimming 0-100%
• DMX-512 protocol
• 3-Pin DMX Connections
• 3 DMX Channel Modes: 16/18/22
• Multiple Unit Power Linking (See page 32)
Included:
1 x powerCON Cable
1 x Omega Bracket
2 x Safety Cables
Focus Spot 4Z/Focus Spot 4Z Pearl Warranty Registration
The Focus Spot 4Z/Focus Spot 4Z Pearl carries a 2 year limited warranty. Please fill out the enclosed
warranty card to validate your purchase. All returned service items whether under warranty or not,
must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must
be clearly written on the outside of the return package. A brief description of the problem as well as
the R.A. number must also be written down on a piece of paper included in the shipping carton. If the
unit is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain a
R.A. number by contacting our customer support team on our customer support number. All packages returned to the service department not displaying a R.A. number on the outside of the package
will be returned to the shipper.
Focus Spot 4Z/Focus Spot 4Z Pearl Installation
The unit should be mounted using a mounting clamp (not provided), axing it to the mounting
bracket that is provided with the unit. Always ensure that the unit is rmly xed to avoid vibration
and slipping while operating. Always ensure that the structure to which you are attaching the unit is
secure and is able to support a weight of 10 times the unit’s weight. ALWAYS use safety cables that
can hold 12 times the weight of the unit when installing the xture.
This equipment must be installed by a professional, and it must be installed in a place where it is out
of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 4
Focus Spot 4Z/Focus Spot 4Z Pearl Safety Precautions
• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to
remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”
(15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 23
for cleaning details.
• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the fixture.
C. The fixture does not appear to operate normally or exhibits a marked change in performance.
D. The fixture has fallen and/or subjected to extreme handling.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 5
Focus Spot 4Z/Focus Spot 4Z Pearl Safety Precautions
POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS
External sources of light beams from direct sunlight, lighting moving head xtures, and lasers, which
are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ
lighting xtures, can cause severe internal damage including burning to optics, dichroic color lters,
glass and metal gobos, prisms, animation wheels, frost lters, iris, shutters, motors, belts, wiring,
discharge lamps, and LEDs.
This issue is not specic only to ADJ lighting xtures, it is a common issue with lighting xtures
from all manufacturers. Although there is no true way to fully prevent this issue from happening, the
guidelines below can prevent any potential damage from occurring if followed. Contact ADJ Service
for more details.
DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT
SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS WHILE UNPACKING,
INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS.
DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 6
Focus Spot 4Z/Focus Spot 4Z Pearl Installation
When installing the unit, the trussing or area of installation must be able to hold 10 times the weight
without any deformation. When installing the unit must be secured with a secondary safety attachment,
e.g. and appropriate safety cable. Never stand directly below the unit when mounting, removing, or
servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation
material being used, and perodic safety inspection of all installation material and unit. If you lack
these qualications, do not attempt the installation yourself.
These installaiton should be checked by a skilled person once a year.
The Focus Spot 4Z/Focus Spot 4Z Pearl is fully operational in three dierent mounting positions,
hanging upside-down from a ceiling or trussing, sideways on trussing, or set on a at level surface.
Be sure this xture is kept at least 12m (40ft) away from any ammable materials (decoration etc.).
Always use and install the supplied safety cable as a safety measure to prevent accidental damage
and/or injury in the event the clamp fails (see next page). Never use the carrying handles for second-
ary attachment.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 7
Focus Spot 4Z/Focus Spot 4Z Pearl Installation
NOTICE: The suitable enviromental temperature for this lighting xture is between -25˚ C to 45˚ C.
Do not place this lighting xture in an enviroment where the temperatures are under or above the
temperatures stated above. This will allow the xture to run at its best and help prolong the xture
life.
SAFETY CABLE
Screw one clamp each via a M12 screw and nut into the Omega bracket. Insert the quick-lock fasteners
of the Omega holder’s into the respective holes on the bottom of the Focus Spot 4Z/Focus Spot 4Z
Pearl. Tighten the quick-lock fasteners fully clockwise. Pull the safety cable through the openings
located on the base plate and over the trussing system or a safe xation spot. Insert the end in the
carabine and tighten the safety screw.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 8
Focus Spot 4Z/Focus Spot 4Z Pearl Overview
Service Port
LED Display
Mode Button
Up Button
Down Button
powerCON In
Fuse Holder
3-Pin XLR Out
3-Pin XLR In
powerCON Out
Left Button
Right Button
Enter Button
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 9
Focus Spot 4Z/Focus Spot 4Z Pearl DMX Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-
nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions
from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only
have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be
linked together and operate from a single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use
the shortest cable path possible. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed
anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation): The Focus Spot 4Z/Focus Spot 4Z
Pearl can be controlled via DMX-512 protocol. The Focus Spot 4Z/Focus Spot 4Z Pearl has 3 DMX
channel modes. The DMX address is set on the front panel of the Focus Spot 4Z/Focus Spot 4Z Pearl. Your
unit and your DMX controller require a standard 3-pin XLR connector for data input and data output (Figure
1). We recommend Accu-Cable DMX cables. If you are making your own cables, be
sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at
almost all pro lighting stores). Your cables should be made with a male and female
XLR connector on either end of the cable. Also remember that DMX cable must be
daisy chained and cannot be split.
Figure 1
Notice: Be sure to follow gures two and three when making your own cables. Do not use the ground
lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the
shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a
short circuit and erratic behavior.
XLR Male Socket
1 Ground
Figure 3
DMX512 OT
3-PIN XLR
2 Cold
3 Hot
1
3
2
XLR Female Socket
2 Cold
COMMON
DMX +
DMX -
1 Ground
3 Hot
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 10
Focus Spot 4Z/Focus Spot 4Z Pearl DMX Set Up
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
and PIN 3 (DMX +) of the last fixture.
Special Note: Line Termination.
When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is
connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted
in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable
terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.
Termination reduces signal errors and
1
3
avoids signal transmission problems
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
Figure 4
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-512 data cables for DATA transmission in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line. When inserting
standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily
available at most electric stores. The chart below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 11
Focus Spot 4Z/Focus Spot 4Z Pearl DMX Addressing
All xtures should be given a DMX starting address when using a DMX controller, so the correct xture
responds to the correct control signal. This digital starting address is the channel number from which
the xture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment
of this starting DMX address is achieved by setting the correct DMX address on the digital control
display on the xture.
You can set the same starting address for all xtures or a group of xtures, or set dierent addresses
for each individual xture. Setting all xtures to the same DMX address will cause all xtures to react
in the same way, in other words, changing the settings of one channel will aect all the xtures
simultaneously.
If you set each xture to a dierent DMX address, each unit will start to “listen” to the channel number
you have set, based on the quantity of DMX channels of each xture. That means changing the settings
of one channel will only aect the selected xture.
In the case of the Focus Spot 4Z/Focus Spot 4Z Pearl, when in 16 channel mode you should set the
starting DMX address of the rst unit to 1, the second unit to 17 (16 + 1), the third unit to 33 (17 + 16),
and so on. (See the chart below for more details.)
Channel Mode
Unit1
Address
Unit2
Address
Unit3
Address
Unit4
Address
16Channels 1 17 33 49
18 Channels 1 19 37 55
22Channels 1 23 45 67
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 12
Focus Spot 4Z/Focus Spot 4Z Pearl DMX Modes & Values
Channel Modes & Values
Basic Standard Extended
1 1 1
2 2
2 3 3
4 4
3 5 5
4 6 6
5 7 7
Values
000-255
000-255
000-255
000-255
000-007
008-014
015-021
022-028
029-035
036-042
043-049
050-056
057-063
064-127
128-189
190-193
194-255
000-004
005-019
020-034
035-049
050-064
065-079
080-094
095-109
110-124
125-139
140-154
155-169
170-189
190-221
222-223
224-255
000-127
128-191
192-255
Functions
PAN Movement 8-bit:
Pan Movement By 630/540
Pan Fine 16-bit:
Fine control of Pan movement
TILT Movement 8-bit:
Tilt Movement
Tilt Fine 16-bit:
Fine control of Tilt movement
Color Wheel:
White
Red
Orange
Yellow
Green
Blue
Pink
Cyan
Magenta
Color Mixing
Color Wheel Clockwise Rotation Fast-Slow
Nothing
Color Wheel Counter-Clockwise Rotation
Slow-Fast
Gobo Wheel
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 1 Shake Slow-Fast
Gobo 2 Shake Slow-Fast
Gobo 3 Shake Slow-Fast
Gobo 4 Shake Slow-Fast
Gobo 5 Shake Slow-Fast
Gobo 6 Shake Slow-Fast
Gobo Wheel Clockwise Rotation Fast-Slow
Nothing
Gobo Wheel Counter-Clockwise Rotation
Slow-Fast
Gobo rotation:
Gobo Rotation Indexing
Gobo Rotation Clockwise Fast-Slow
Gobo Rotation Counter-Clockwise Slow-Fast
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 13
Focus Spot 4Z/Focus Spot 4Z Pearl DMX Modes & Values
Channel Modes & Values
Basic Standard Extended Values
000-031
032-063
064-095
6 8 8
096-127
128-159
160-191
192-223
224-255
7 9 9
10
8 10 11
000-255
000-255
000-031
032-255
Functions
Shutter & Strobing:
Shutter Closed (Not Function)
Shutter Open
Strobing Slow-Fast
Shutter Open
Pulse Strobing Slow-Fast
Shutter Open
Random Strobing Slow-Fast
Shutter Open
Master Dimmer:
Intensity 0 to 100%
Dimmer Fine 16-bit:
Prism 1:
Open
6 Facet Circular Prism
9 11 12
13
10 12 14
11 13 15
16 Prism 2 Indexing Fine 16-bit:
12 14 17
000-127
128-189
190-193
194-255
000-255
000-031
032-255
000-127
128-189
190-193
194-255
000-255
000-255
Prism 1 Indexing & Rotation:
Prism 1 Indexing
Clockwise Rotation Fast-Slow
No Rotation
Counter-Clockwise Rotation Slow-Fast
Prism 1 Indexing Fine 16-bit:
Prism 2:
Open
5 Facet Linear Prism
Prism 2 Indexing & Rotation:
Prism 1 Indexing
Clockwise Rotation Fast-Slow
No Rotation
Counter-Clockwise Rotation Slow-Fast
Focus:
Continuous adjustment from far to near
13 15 18
19
000-255
000-255
Zoom:
Zoom from min. to max.beam angle
Zoom Fine 16-bit:
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 14
Focus Spot 4Z/Focus Spot 4Z Pearl DMX Modes & Values
Channel Modes & Values
Basic Standard Extended Values
000-020
021-040
041-060
14 16 20
15 17 21
16 18 22
061-080
081-100
101-120
121-255
000-255
000-009
010-019
020-029
030-039
040-059
060-069
070-079
080-089
090-099
100-119
120-139
140-159
160-179
180-199
200-219
220-239
240-255
Functions
Dim Curves:
Standard
Stage
TV
Architectural
Theatre
Stage 2
Default tu Unit Setting
Pan/Tilt Speed:
Max to min speed
Function, reset, internal programs
No Function
Blackout with Pan/Tilt Movement
Blackout with Color Wheel Movement
Blackout with Gobo Wheel Movement
Color and Gobo Motor Reset
Prism Motor Reset
Pan & Tilt Motor Reset
Focus Motor Reset
All Motors Reset
Internal Program 1 (Scene 1~8 of EEPROM)
Internal Program 2 (Scene 9~16 of EEPROM)
Internal Program 3 (Scene 17~24 of EEPROM)
Internal Program 4 (Scene 25~32 of EEPROM)
Internal Program 5 (Scene 33~40 of EEPROM)
Internal Program 6 (Scene 41~48 of EEPROM)
Internal Program 7 (Scene 49~56 of EEPROM)
No Function
Focus Spot 4Z/Focus Spot 4Z Pearl Gobos
Inner Diameter: 19mm
Outer Diameter: 23mm
Thickness: 0.5mm
Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 15
Focus Spot 4Z/Focus Spot 4Z Pearl System Menu
MENU SUB MENU OPTIONS/VALUES (DEFAULT SHADED) DESCRIPTION
Software Update
Please Wait
DISPLAY MENU
RECEIVE
USER MODE
FOCUS SPOT 4Z
Motor Reset
Please Wait…
Set Address
User Mode
Edit A
Edit B
Edit C
Status
Dim Mode
A001~AXXX
Standard (18 Channel Mode)
Basic (16 Channel Mode)
Extend (22 Channel Mode)
User A
User B
User C
Max Channel
PAN
:
No DMX Mode
P.Reverse
T.Reverse
Pan Degree
Feedback
Move.Speed
Hibernation
Hold/Auto/Black
ON/OFF
ON/OFF
630/ 540
ON/OFF
Speed 1 ~ 4
OFF, 01M~99M，15M
Standard
Stage
TV
Architectur
Theatre
Stage2
Celsius
Fahrenheit
900Hz/1000Hz/1100Hz/
1200Hz/1300Hz/1400Hz/
1500Hz/2500Hz/4000Hz/
5000Hz/10KHz/15KHz/
20KHz/25KHz
Auto
High
Low
02~60m <05m>
ON/OFF
ON/OFF/ON1
ON/OFF
PAN……
Slave1,Slave2,Slave3
Master / Alone
FUNCTION
Temp. C/F
Gamma 2.0/2.2/2.4/2.6/2.8
Frequency
Fan Set
LCD.Set
Disp.Set
USB Update
DFSE
Head Fan
Backlight
FlipDisplay
Key Lock
Disp Flash
Chan.Value
Slave Set
Auto.Prog
OFF/ON
ON/OFF
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 16
Focus Spot 4Z/Focus Spot 4Z Pearl System Menu
MENU SUB MENU OPTIONS/VALUES (DEFAULT SHADED) DESCRIPTION
INFORMATION
TEST
PROGRAM
Time.Info
Temp. Info
Fan Speed
Error.Info
Model. Info
Software.V
Reset.Motor
TestChannel
Panel.Ctrl
Calibrate
Select.Prog
Edit.Prog
Edit.Scene
CurrentTime
Total Time
Last Time
Timer PIN
Clear Last
Clear Total
T:XXX
Fan1: XXXX RPM
Fan2: XXXX RPM
NONE/Pan,Tilt …
FOCUS SPOT 4Z
1U: VX.X.X
2U: VX.X.X
3U: VX.X.X
All
Pan&Tilt
Color&Gobo
Pan/Pan Fine/Tilt/Tilt Fine/ColorWheel/Gobo/RotGobo/
Strobe/Dimmer/Dim Fine/Prism1/Prism1Rot/Prism1 Fine/
Prism2/Prism2Rot/Prism2 Fine/Focus/Zoom/ZoomFine/
DimMode/P/T Speed/Reset/Prog
Pan/Pan Fine/Tilt/Tilt Fine/ColorWheel/Gobo/RotGobo/
Strobe/Dimmer/Prism1/Prism1Rot/Prims2/Prism2Rot/
Focus/Zoom/DimMode/P/T Speed/ Reset/Prog
Password
Pan/Tilt/ColorWheel/Gobo/RotGobo/Prism1/
Prism1Rot/Prism2/Prism2Rot/Focus/Zoom
Prog.Part 1 = Program 1~9 Program 1
Prog.Part 2 = Program 1~9 Program 2
Prog.Part 3 = Program 1~9 Program 3
Program 1
:
Program 9
Edit Scene 001
~ Edit Scene 250
Program Test
Step 01=SCxxx
Step 64=SCxxx
Pan,Tilt, ……
Fade Time
Secne Time
Current Running Time (Hours)
Total Running Time (Hours)
Total Running Time (Hours)
Last Time Clear:
(Password=050)
Total Time Clear:
(Password=060)
ON/OFF
ON/OFF
(Password=050)
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 17
Focus Spot 4Z/Focus Spot 4Z Pearl Operating Instructions
The main menu is accessed by pressing the MODE button. Browse through the menu by using the UP,
DOWN, RIGHT, & LEFT buttons. Press the ENTER button to access the desired menu. You can scroll through
the submenus using the UP and DOWN buttons. To conrm every selection press the ENTER button. You
can exit every menu and submenu by pressing the MODE button. The unit will automatically exit the menus
if no buttons are pressed after 10 seconds. These next pages will explain each function in the system menu
located on the previous pages.
SET ADDRESS - With this function, you can adjust and set your desired DMX address.
1. Access the main menu, and press the UP or DOWN buttons until “Receive” is higlighted, then press
ENTER.
2. “Set Address” will now be displayed, press ENTER. The current DMX address will now be displayed.
3. Use the UP or DOWN buttons to adjust the DMX address.
4. Press the ENTER button to conrm your address or press the MODE button to exit.
USER MODE - This mode will let you select your desired DMX Channel mode.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons until “User Mode” is
highlighted, then press ENTER. Hightlight “User Mode” once again and press ENTER.
2. Use the UP or DOWN buttons to scroll through the 3 DMX Channel Modes. See the DMX channel modes
listed below. Press the ENTER button to conrm your selection or press the MODE button to exit.
• Basic Mode - This is 16 Channel Mode.
• Standard Mode - This is 18 Channel Mode.
• Extended Mode - This is 22 Channel Mode.
User Mode A B C - These are customizable DMX modes. Select either of these modes and set the amount of
DMX Channels and what each channel does.
3. Press the ENTER button to corm your settings or press the MODE button to exit.
NO DMX MODE - With this function if the DMX signal is suddenly lost, the unit will automatically go into 1 of
3 modes.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons until “Function” is highlighted,
then press ENTER.
2. Press the UP or DOWN buttons until “Status” is highlighted, then press ENTER.
3. Press the UP or DOWN buttons, until “No DMX Mode” is highlighted, then press ENTER.
4. Either “Hold” (Last DMX setting), “Black” (Blackout), or “Auto” (Auto Program) will be displayed, use the
UP or DOWN buttons to scroll through the options.
5. Press the ENTER button to conrm your selection or press the MODE button to exit.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 18
Focus Spot 4Z/Focus Spot 4Z Pearl Operating Instructions
PAN INVERSE - With this function you can reverse the Pan movement.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons until “Function” is highlighted,
then press ENTER.
2. Press the UP or DOWN buttons until “Status” is highlighted then press ENTER.
3. Press UP or DOWN buttons until “P. Reverse” is highlighted then press ENTER.
4. Either “O” or “On” will be displayed. Press the UP or DOWN buttons to nd your desired setting.
5. Press the ENTER button to conrm your setting or press the MODE button to exit.
TILT INVERSE - With this function you can reverse the left head Tilt movement. This function is used with
DMX mode.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Status” is highlighted then press ENTER.
3. Press the UP or DOWN buttons until “T. Reverse” is highlighted then press ENTER.
4. Either “O” or “On” will be displayed. Press the UP or DOWN buttons to nd your desired setting.
5. Press the ENTER button to conrm your setting or press the MODE button to exit.
PAN DEGREE - With this function you can change the pan degree from 630 to 540. This function is used
with DMX mode.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Status” is highlighted press ENTER.
3. Press THE UP or DOWN buttons until “Pan Degree” is highlighted and press ENTER.
4. Either “540” or “630” will be displayed. Use the UP or DOWN buttons to nd your desired setting.
5. Press the ENTER button to conrm your selection or press the MODE button to exit.
FEEDBACK - With this function, you have the pan and tilt postion feedback while out of step or not feed-
back while out of step.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
2. Press the LEFT or RIGHT buttons until “Status” is highlighted press ENTER.
3. Press LEFT or RIGHT buttons, until “Feedback” is highlighted and press ENTER.
4. Either “O” or “On” will be displayed. Use the UP or DOWN buttons to nd your desired setting.
5. Press the ENTER button to conrm your selection or press the MODE button to exit.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 19
Focus Spot 4Z/Focus Spot 4Z Pearl Operating Instructions
MOVEMENT SPEED - With this function you can set the pan and tilt movement speed.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons until “Function” is highlighted,
then press ENTER.
2. Press the UP or DOWN buttons until “Status” is highlighted then press ENTER.
3. Press UP or DOWN buttons until “Move. Speed” is highlighted then press ENTER.
4. Either “Speed1”, “Speed2”, “Speed3” or “Speed4” will be displayed. Use the UP or DOWN buttons to
nd your desired setting.
5. Press the ENTER button to conrm your selection or press the MODE button to exit.
HIBERNATION - With this function the LEDs and step motors will power o if there is no DMX signal within
15 mins (factory defualt). Once it receives a DMX signal, the xture will reset itself.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons until “Function” is highlighted,
then press ENTER.
2. Press the UP or DOWN buttons until “Status” is highlighted then press ENTER.
3. Press UP or DOWN buttons, until “Hibernation” is highlighted then press ENTER.
4. The current stand by setting will be displayed, use the LEFT or RIGHT buttons to adjust the hibernation
period between “01M-99M” or “O”.
5. Press the ENTER button to conrm your selection or press the MODE button to exit.
DIMMER MODE - With this function you can change dimmer curve setting. See page 28 for the Dimmer
Curve Chart.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Dim Mode” is highlighted then press ENTER.
3. The dimmer curve settings will now be displayed.
4. Use the UP or DOWN buttons to nd your desired dimmer curve setting.
5. Press the ENTER button to conrm your selection or press the MODE button to exit.
TEMPERATURE C/F - With this function, you can change the temperature display to show either Celsius or
Fahrenheit.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
2. Press UP or DOWN buttons until “Temp. C/F” is highlighted then press ENTER.
3. Either “Celsius” or “Fahrenheit” will be displayed, use the UP or DOWN buttons to nd your desired setting.
4. Press the ENTER button to conrm your selection or press the MODE button to exit.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 20
Focus Spot 4Z/Focus Spot 4Z Pearl Operating Instructions
GAMMA ADJUSTMENT - With this function, you are able to adjust the gamma setting. This feature is predominately
used when shooting video.
1. Access the main menu, and press the UP or DOWN buttons until “Function” is higlighted, then press
ENTER.
2. Press the UP or DOWN buttons until “Gamma” is highlighted, and press ENTER. The current setting will
now be displayed.
3. Use the UP or DOWN buttons to nd your desired setting.
4. Press the ENTER button to conrm your selection or press the MODE button to exit.
FREQUENCY ADJUSTMENT - With this function, you are able to adjust the dimming frequency. This feature
is predominately used when shooting video and achieving icker free operation.
1. Access the main menu, and press the UP or DOWN buttons until “Function” is higlighted, then press
ENTER.
2. Press the UP or DOWN buttons until “Frequen” is highlighted, then press ENTER. The current setting will
now be displayed.
3. Use the UP or DOWN buttons to nd your desired setting.
4. Press the ENTER button to conrm your selection or press the MODE button to exit.
FAN SET - With this function, you can control the moving head fan speed.
1. Access the main menu, and press the UP or DOWN buttons until “Function” is higlighted, then press
ENTER.
2. Press the UP or DOWN buttons until “Fan Set” is highlighted, and press ENTER.
3. “Head Fan” will now be displayed, press ENTER.
4. Use the UP or DOWN buttons to make the adjustments to the fan.
5. Press the ENTER button to conrm your selection or press the MODE button to exit.
BACKLIGHT - With this function you can have the LCD display backlight after 2-60 minutes. Use this function
to adjust the time.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons until “Function” is highlighted,
then press ENTER.
2. Press the UP or DOWN buttons until “LCD.Set” is highlighted, press ENTER.
3. Press UP or DOWN buttons, until “Backlight” is highlighted, and press ENTER.
4. “05m” (5 minutes) will be displayed, this is the default setting. Use the LEFT or RIGHT buttons to adjust the
shuto time between 02m-60m or “O”.
5. Press the ENTER button to conrm your selection or press the MODE button to exit.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 21
Focus Spot 4Z/Focus Spot 4Z Pearl Operating Instructions
FLIP DISPLAY - With this function you can rotate (ip) the display 180 degrees.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “LCD.Set” is displayed, press ENTER.
3. Press UP or DOWN buttons, until “Flip Display” is displayed, and press ENTER.
4. Either “O” or “On” will be displayed. Use the LEFT or RIGHT buttons nd your setting.
5. Press the ENTER button to conrm your selection or press the MODE button to exit.
KEY LOCK - With this function activated the buttons will lock autommatically after 15 seconds.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “LCD.Set” is highlighted, then press ENTER.
3. Press UP or DOWN buttons, until “Key Lock” is highlighted, then press ENTER.
4. Use the LEFT and RIGHT buttons to scroll through the key lock options, and press ENTER to
make your selection.
• “OFF” - The keypad is unlocked, simply press the MODE button to activate the keypad.
• “ON” - This is a simple keypad lock. Press the MODE button for at least 5 seconds to unlock the
keypad.
• “ON1. This setting is used to prevent the accidental unlocking of the keypad. To unlock the keypad
you will have to enter a passcode. To unlock the keypad press UP, DOWN, UP, DOWN, & ENTER
in that order.
5. Press the ENTER button to conrm your selection or press the MODE button to exit.
DISPLAY FLASH - With this function active, the display will ash when the DMX signal is lost.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “LCD.Set” is highlighted, then press ENTER.
3. Press UP or DOWN buttons, until “DispFlash” is highlighted, then press ENTER.
4. Either “O” or “On” will be displayed. Use the LEFT or RIGHT buttons nd your setting.
5. Press the ENTER button to conrm your selection or press the MODE button to exit.
CHANNEL VALUE - This function will allow you to see the DMX value of each DMX channel that is currently
being used at the time.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Disp.Set” is highlighted, then press ENTER.
3. Press the UP or DOWN buttons until “Chan. Value” is highlighted, then press ENTER.
4. A DMX Channel will now be displayed. Example: Pan, Rotation, LED’s etc... Press ENTER when you nd
the DMX channel that you would like to check. When you press ENTER the DMX value of that channel will
displayed.
5. Press the MODE button to exit.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 22
Focus Spot 4Z/Focus Spot 4Z Pearl Operating Instructions
SLAVE SET - This function lets you designate the unit as the slave in a Master-Slave conguration.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Disp.Set” is highlighted, then press ENTER.
3. Press the UP or DOWN buttons until “Slave Set” is highlighted, then press ENTER.
4. Either “Slave 1”, “Slave 2”, or “Slave 3” will be displayed. Use the UP or DOWN buttons to nd your desired
setting.
5. Press the ENTER button to conrm your selection or press the MODE button to exit.
AUTO PROGRAM - This function allows the internal programs to run in either stand-alone or master/
slave set up. In “Master” mode the xture will send DMX data to other xtures connected via DMX cable. In
“Alone” mode the xture will operate as a single xture. The program for this mode is selected in the “Program”
section of the control menu. You can set the number of steps under “Edit.Prog”. You can edit the individual
scenes under “Edit Scenes”.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Disp.Set” is displayed, press ENTER.
3. Press the UP or DOWN buttons until “Auto. Prog” is displayed, and press ENTER.
4. Either “Master” or “Alone” will be displayed. Use the UP or DOWN buttons to nd your desired setting.
5. Press the ENTER button to conrm your selection or press the MODE button to exit.
DEFAULT SETTINGS - With this function you can restore the factory settings.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons so that “DFSE” is highlighted, then press ENTER.
3. Either “O” or “On” will now be displayed. Use the LEFT or RIGHT buttons to nd your selection. Selecting
“On” will restore the factory settings.
4. Press the ENTER button to conrm your selection or press the MODE button to exit.
USB UPGRADE FILE - This submenu is used for any future software updates. Check www.adj.com
and this units webpage for any software updates. Download the software update to a ash stick and
plug the ash stick into the Service Port slot located on the front of the unit.
1. Contact ADJ customer service for help when updating software.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 23
Focus Spot 4Z/Focus Spot 4Z Pearl Operating Instructions
TIME INFO - In this submenu are able to check the current running time, total running time, and last clear
time. This submenu will also let you clear/reset the “Total Time” and “Last Time” hours.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons until “Information” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Time.Info” is highlighted, then press ENTER.
3. Press UP or DOWN buttons to scroll through the time information selections.
• “Current Time” - This will display the current running time of the fixture in hours. Press the ENTER
or MODE button to exit.
• “Total Time” - This will display the total running time of the fixture in hours. Press the ENTER or
MODE button to exit.
• “Last Time” - This will display the last time the running time was cleared. Press the ENTER or
MODE button to exit.
• “Time PIN” - This function will allow you to clear the “Last Time” and “Total Time” displays.
• “Clear Last” - This function will allow you to clear the “Last Time” counter. Access “Time PIN”
and press ENTER. Using the UP and DOWN buttons set the “PIN” to “050” and press ENTER.
Return to the “Clear Last” function and press ENTER. Press the LEFT or RIGHT buttons
until your selection is displayed and press ENTER to confirm. “ON” will clear the time. “OFF” will
return you to the Time Menu.
• “Clear Total” - This function will allow you to clear the “Total Time” counter. Access “Time PIN”
and press ENTER. Using the UP and DOWN buttons set the “PIN” to “060” and press ENTER.
Return to the “Clear Total” function and press ENTER. Press the LEFT or RIGHT buttons until
your selection is displayed and press ENTER to confirm. “ON” will clear the time. “OFF” will
return you to the Time Menu.
TEMPERATURE INFO - This will allow you to check the moving head temperature.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons until “Information” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Temp. Info” is highlighted, then press ENTER.
3.. “T:XXX” will now be displayed. “XXX” represents the current temperature of the moving head.
4. Press the ENTER button or MODE button to exit.
FAN SPEED - With this function, you can control the base fan speed.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons until “Information” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Fan Speed” is highlighted, then press ENTER.
3. The current fan speeds of “Fan1” and “Fan2” will now be displayed.
4. Press the ENTER or MODE button to exit.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 24
Focus Spot 4Z/Focus Spot 4Z Pearl Operating Instructions
ERROR INFO - This submenu will display any function errors that may occur. If any error warnings appear
and you are not certain on what form of action needs to be taken, please contact ADJ customer support for
more information.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Information” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Error. Info” is highlighted, then press ENTER.
3. Any errors that have may occured will now be displayed. Press the MODE button to exit.
MODEL INFORMATION - This will display the model name
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Information” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Model.Info” is highlighted, then press ENTER.
3. The model name will now be displayed.
4. Press the ENTER or MODE button to exit.
SOFTWARE VERSION - This will display the current software version.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons until “Information” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Software.V” is highlighted, then press ENTER.
3. The current software versions will now be displayed.
4. Press the ENTER or MODE button to exit.
RESET MOTOR - This will allow you to reset the pan, tilt, color wheel, gobo wheel motors, or all motors.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Test” is highlighted,
then press ENTER.
2. Press the UP or DOWN buttons until “Reset.Motor” is highlighted, then press ENTER.
3. Press the UP or DOWN buttons to nd the motors you would like to reset.
4. Press the ENTER button to reset or press the MODE button to exit.
TEST CHANNEL - With this function you can test each of the channel functions.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Test” is highlighted,
then press ENTER.
2. Press the UP or DOWN buttons until “TestChannel” is highlighted, then press ENTER.
3. Use the UP or DOWN buttons to scroll through the channel functions.
4. Press ENTER to select a channel to test or press MODE to exit.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 25
Focus Spot 4Z/Focus Spot 4Z Pearl Operating Instructions
PANEL CONTROL - With this function you can make ne adjustments.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Test” is highlighted,
then press ENTER.
2. Press the UP or DOWN buttons until “Panel. Ctrl” is displayed, press ENTER.
3. Use the UP or DOWN buttons to scroll through the various functions.
4. Press ENTER when you nd the function you would like to adjust or press MODE to exit.
CALIBRATE - With this function you can calibrate and adjust the eect wheels to their correct positions. The
Calibration password 050. NOTE: ONLY QUALIFIED TECHNICIANS SHOULD PERFORM THIS FUNCTION.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Test” is highlighted,
then press ENTER.
2. Press the UP or DOWN buttons until “Calibrate” is displayed, press ENTER.
3. “XXXX” will be displayed. The password is 050.
4. Press ENTER to conrm or press MODE to exit.
PROGRAM
EDIT PROGRAM: - The xture comes equipped with a built-in DMX recorder that allows custom programs to
be installed and recalled directly from the xture’s control board. Programs can be created and stored using
the xture’s control board or by using an external DMX controller.
Select.Prog – This function allows the user to select one of nine of the user dened built-in programs. This
program is then accessed in “Function Mode” under “Program Run.”
Edit.Prog – This function allows the user to edit the built-in programs.
Edit.Scene – This function allows the user to edit or dene the actual scenes that are stored in the user
dened built-in programs that are accessed in the previous step.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 26
Focus Spot 4Z/Focus Spot 4Z Pearl Operating Instructions
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-Slave set-up. In a Master-Slave
set up one unit will act as the controlling unit and the others will react to the controlling units built-in
programs. Any unit can act as a Master or as a Slave however, only one unit can be programmed to
act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit. Use standard XLR data
cables to link your units together. Remember that the Male XLR connector is the input and the
Female XLR connector is the ouput. The first unit in the chain (master) will use the female XLR
connector only. The last unit in the chain will use the male XLR connector only.
2. Connect the rst “Slave” unit to the “Master.”
3. Master Unit:
• Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
• Press the UP or DOWN buttons until “Disp.Set” is displayed, press ENTER.
• Press the UP or DOWN buttons until “Auto. Prog” is displayed, and press ENTER.
• Either “Master” or “Alone” will be displayed. Use the UP or DOWN buttons to highlight “Master”.
• Press the ENTER button to conrm your selection.
4. Slave Unit(s):
• Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Function” is
highlighted, then press ENTER.
• Press the UP or DOWN buttons until “Disp.Set” is highlighted, then press ENTER.
• Press the UP or DOWN buttons until “Slave Set” is highlighted, then press ENTER.
• Either “Slave 1”, “Slave 2”, or “Slave 3” will be displayed. Use the UP or DOWN buttons to nd your desired
slave setting.
5. Press the ENTER button to conrm your selection.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 27
Focus Spot 4Z/Focus Spot 4Z Pearl Dimmer Curve Chart
50%
255 255
0 0
DIMMER
100%
10%
0%
Time (ms)
Rise Time Down Time
0 Sec
0 sec Fade Time 1 sec Fade Time
Dimming Curve
Ramp Effect
Rise Time (ms) Down Time (ms) Rise Time (ms) Down Time (ms)
Standard (default) 0 0 0 0
Stage 780 1100 1540 1660
TV 1180 1520 1860 1940
Architectural 1380 1730 2040 2120
Theatre 1580 1940 2230 2280
Stage 2
0 1100 0 1660
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 28
Focus Spot 4Z/Focus Spot 4Z Pearl Dimensional Drawing
7.15” / 181.49mm
3.41” / 86.5mm
10.94” / 277.79mm
3.69” / 93.7mm
18” / 457.4mm
13.14” / 333.75mm
6.85” / 174mm
9.07” / 230.36mm
10.97” / 278.61mm
11.07” / 281.27mm
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 29
Focus Spot 4Z/Focus Spot 4Z Pearl Gobo Replacement
The gobo’s featured in this unit are interchangable. Remember when changing these gobo’s that
they are thin and easy to bend. Please do this process gently so you do not bend or damage gobo.
Caution! Never open the unit when in use. Always disconnect the main power before attempting to
change the gobos.
Locating the Gobo wheel: After disconnecting the main power, position the head with the lens
facing forward. Look through lens of the unit. When looking through the front lens, position the head
so that the gears are on the right side. When the gears are on the right side, the shell that needs to
be uscrewed is now facing up.
1. To change a gobo, uscrew the 4 screws that secure the shell to the unit. Gently lift and remove the
shell.
2. When you remove the shell you will be able to access the gobo wheel. Turn the wheel with your
hand until you come across the gobo you would like to change.
3. To change the gobo you have to remove the individual gobo frames. Gently push the gobo and
gobo frame (Not the wheel) away from the gobo wheel. You do not have to the push very hard. While
you are pushing the gobo frame away from the wheel, gently pull the the gobo frame up and out.
4. Once the gobo frame has been removed, you will notice that a retainer ring secures the gobo in
place. After the retainer ring is removed, your are able to remove the gobo.
5. Change the gobo and replace the retainer ring.
6. Insert the gobo frame back into the unit, positioning it in same way as the other gobo frames.
7. Reassemble the unit.
Focus Spot 4Z/Focus Spot 4Z Pearl Gobos
Inner Diameter: 19mm
Outer Diameter: 23mm
Thickness: 0.5mm
Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 30
Focus Spot 4Z/Focus Spot 4Z Pearl Fuse Replacement
Unplug the unit from any power source it may be connected to. Once the power has been disconnected,
use a flat head screw driver to unscrew the fuse holder located next to the powerCON input. Remove
the bad fuse and replace with a new one, and screw the fuse holder back in.
Focus Spot 4Z/Focus Spot 4Z Pearl Multiple Unit Power Linking
With this feature you can connect the xtures to one another using the power cable input and
output sockets.
NOTE: USE CAUTION WHEN POWER LINKING OTHER FIXTURES AS THE POWER
CONSUMPTION OF OTHER MODEL FIXTURES MAY EXCEED THE MAX POWER OUTPUT ON
THIS FIXTURE! CHECK SILK SCREEN FOR MAX AMPS.
Focus Spot 4Z/Focus Spot 4Z Pearl Trouble Shooting
Listed below are a few common problems the user may encounter, with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on
some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right
connectors; it does matter which way the inputs and outputs are connected.
Focus Spot 4Z/Focus Spot 4Z Pearl Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2. Clean the external optics with glass cleaner and a soft cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust, dew).
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 31
Focus Spot 4Z/Focus Spot 4Z Pearl Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•NonL.E.D.LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect
Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par
Cans, Trussing, Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding batteries which have a 180 day lim-
ited warranty). Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.
•StarTecSeries=1YearLimitedWarranty(excluding batteries which have a 180 day limited warranty).
•ADJDMXControllers=2Year(730Days)LimitedWarranty
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 32
Focus Spot 4Z/Focus Spot 4Z Pearl Specifications
Focus Spot 4Z/Focus Spot 4Z Pearl
Voltage: 100V ~ 240V/50~60Hz
LEDs: 1 x 200W LED
Working Position: Any safe working position
Power Draw: 256W
Fuse: 3A
Dimensions: 7.15” (L) x 10.97” (W) x 18” (H)
181.5 x 278.61 x 457.4mm
Weight: 23lbs. / 10 kgs
Colors: 8 Colors + White
Gobos: 6 Gobos + Open
Inner Diameter: 19mm
Outer Diameter: 23mm
Thickness: 0.5mm
DMX Channels: 3 DMX Modes: 16/18/22
Warranty: 2 Year (730 days)
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
ADJ Products, LLC - www.adj.com - Focus Spot 4Z/Focus Spot 4Z Pearl User Manual Page 33
Loading...