ADJ 3D Vision Plus Users Manual

3D VISION PLUS

5005510

11/17

User Instructions

©2017 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of
their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and opera­tion of this product.

DOCUMENT VERSION

Please check www.adj.com for the latest revision/update of this guide.

Date

Document

Version

10/19/17 1 3/9/13

DMX

Channel

Modes

Notes

Initial Release

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!

3D Vision Plus Table of Contents

Introduction

Features

Warranty Registration

Safety Precautions

DMX Channel Mode

System Menu

Operating Instructions

DMX Control

Master-Slave Conguration

Multiple Unit Power Linking

Pixel Conguration Diagram

3

11

4

4

5

6

10

13

13

13

14

Mounting and Grouping

Dimensional Drawings

Fuse Replacement

Warranty

Technical Specications

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 2

15

17

18

19

20

3D Vision Plus Introduction

Unpacking: Thank you for purchasing the 3D Vision Plus by ADJ Products, LLC. Every 3D Vision Plus has

been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully
inspect your xture for any damage and be sure all accessories necessary to operate the unit has arrived intact.
In the case damage has been found or parts are missing, please contact our toll free customer support number

for further instructions. Do not return this unit to your dealer without rst contacting customer support.

Introduction: The 3D Vision Plus is a Hexagonal shaped LED panel with stunning 3D visual effects when used

in multiples. This LED panel is controlled via manual control or DMX control. Kling-Net or Art-Net can be used
when used with EZ Kling. Dynamic effects can be played on it, which makes it a great lighting system for DJ’s
and night clubs.

Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide set up help

and to answer any question should you encounter problems during your set up or initial operation. You may
also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through
Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]
To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so

will void your manufactures warranty. In the unlikely event your unit may require service please contact ADJ
Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 3

3D Vision Plus Features

• Multi-Colors

• Electronic Dimming 0-100%

• Built in Microphone

• DMX-512 protocol

• CAT 5 Straight Network Cable included.

• 72 x 5050 SMD 3-in-1 RGB LED’s

• Safety Cable Included

• Three DMX Modes: 3 Channel Mode, 9 Channel Mode, and 13 Channel Mode.

• Multiple Unit Power Linking (See page 13)

3D Vision Plus Warranty Registration

The 3D Vision Plus carries a 2 year limited warranty. Please fill out the enclosed warranty card to
validate your purchase. All returned service items whether under warranty or not, must be freight pre­paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on
the outside of the return package. A brief description of the problem as well as the R.A. number must
also be written down on a piece of paper included in the shipping carton. If the unit is under warranty,
you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by con­tacting our customer support team on our customer support number. All packages returned to the
service department not displaying a R.A. number on the outside of the package will be returned to the
shipper.

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 4

3D Vision Plus Safety Precautions

• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to
remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 18

for cleaning details.

• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the fixture.

C. The fixture has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a marked change in performance.
E. The fixture has fallen and/or subjected to extreme handling.

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 5

3D Vision Plus 3 Channel Mode

Channel Value Function

1 RED

0 - 255 0% - 100%

2 GREEN
0 - 255 0% - 100%

3 BLUE
0 - 255 0% - 100%

3D Vision Plus 9 Channel Mode

Channel Value Function

1 RED 1

0 - 255 0% - 100%

2 GREEN 1
0 - 255 0% - 100%

3 BLUE 1
0 - 255 0% - 100%

4 RED 2

0 - 255 0% - 100%

5 GREEN 2
0 - 255 0% - 100%

6 BLUE 2
0 - 255 0% - 100%

7 RED 3

0 - 255 0% - 100%

8 GREEN 3
0 - 255 0% - 100%

9 BLUE 3
0 - 255 0% - 100%

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 6

3D Vision Plus 13 Channel Mode

Channel Value Function

1 RED 1

0 - 255 0% - 100%

2 GREEN 1
0 - 255 0% - 100%

3 BLUE 1
0 - 255 0% - 100%

4 RED 2

0 - 255 0% - 100%

5 GREEN 2
0 - 255 0% - 100%

6 BLUE 2
0 - 255 0% - 100%

7 RED 3

0 - 255 0% - 100%

8 GREEN 3
0 - 255 0% - 100%

9 BLUE 3
0 - 255 0% - 100%

CHANNEL 13 MODE CONTINUED ON THE NEXT PAGE

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 7

3D Vision Plus 13 Channel Mode

Channel Value Function

10 COLOR MACROS

0 OFF
1 - 7 ALL RED (STATIC)
8 - 14 ALL GREEN (STATIC)

15 - 21 ALL BLUE (STATIC)

22 - 28 ALL YELLOW (STATIC)
29 - 35 ALL CYAN (STATIC)
36 - 42 ALL MAGENTA (STATIC)

43 - 49 RGB CHASE
50 - 57 BLUE, CYAN, & MAGENTA CHASE
58 - 64 MAGENTA, YELLOW, & WHITE CHASE
65 - 71 YELLOW & MAGENTA CHASE
72 - 78 BLACK & BLUE CHASE
79 - 85 RGB FADE
86 - 92 RGBYCMW FADE
93 - 99 YELLOW & BLUE CHASE
100 - 106 RED & CYAN CHASE
107 - 113 GREEN & MAGENTA CHASE

114 - 120 ALL COLORS RANDOM
121 - 127 SOUND ACTIVE RED
128 - 134 SOUND ACTIVE GREEN

135 - 141 SOUND ACTIVE BLUE

142 - 148 SOUND ACTIVE YELLOW
149 - 155 SOUND ACTIVE CYAN
156 - 162 SOUND ACTIVE MAGENTA

163 - 169 SOUND ACTIVE RGB CHASE
170 - 177 SOUND ACTIVE BLUE, CYAN, & MAGENTA CHASE
178 - 184 SOUND ACTIVE MAGENTA, YELLOW & WHITE CHASE
185 - 191 SOUND ACTIVE YELLOW & MAGENTA CHASE
192 - 198 SOUND ACTIVE BLACK & BLUE CHASE
199 - 205 SOUND ACTIVE RGB FADE
206 - 212 SOUND ACTIVE RGBYCMW FADE
213 - 219 SOUND ACTIVE YELLOW & BLUE CHASE
220 - 226 SOUND ACTIVE RED & CYAN CHASE
227 - 233 SOUND ACTIVE GREEN & MAGENTA CHASE

234 - 240 SOUND ACTIVE ALL COLORS
241 - 255 NO FUNCTION

CHANNEL 13 MODE CONTINUED ON THE NEXT PAGE

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 8

3D Vision Plus 13 Channel Mode

Channel Value Function

11 MACRO SPEED/SOUND SENSITIVITY

0 - 255 MACRO SPEED SLOW - FAST
0 - 255 SOUND SENSITIVITY LESS - MORE

12 STROBING/LEDS ON/OFF

0 - 31 LED OFF
32 - 63 LED ON

64 - 95 STROBING SLOW - FAST

96 - 127 LED ON

128 - 159 PULSE STROBING SLOW - FAST

160 - 191 LED ON

192 - 223 RANDOM STROBING SLOW - FAST

224 - 255 LED ON
13 MASTER DIMMER

0 - 255 0% - 100%

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 9

3D Vision Plus System Menu

Menu Option Function Remark

Addr A001-A512 Set DMX Address

NodE CH03 3CH Mode（DMX）

CH13 13CH Mode（DMX）

Nodn

SLAu SLAu

Auto RAND 16 built-in effects automatically

SPEd SP01-SP16 16 speed grade

blac

No DMX signal ，blac Default set to
No DMX signal ，Auto

Soun

Hold

No DMX signal ，Soun
No DMX signal ，Hold
Slave Default set to

loop

Au01-Au16 Specifies to play a built-in effect

Default set to

A001"

“
Default set to
“

CH09" CH09 9CH Mode（DMX）

“

HOLD" Auto

SLAu " NASt Master

“
Default set to

rand "

“

Default set to

SP08"

“

Soun RAND 16 built-in effects automatically

loop

Su01-Su16 Specifies to play a built-in effect

Sobn OFF

sound scene shut o Default set to
sound scene remain on

SEns 1-30 30 Sound Sensitivity grade

ConF Con1-Con6 6 different pixel partitions

(See Page 14 For Diagram)

dIEr dI01-dI16 16 brightness grade

Default set to

rand "

“

OFF ON

“
Default set to

“ 15”
Default set to

Con1”

“
Default set to
“

dl16”

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 10

3D Vision Plus Operating Instructions

System Menu: When making adjustments press ENTER to conrm your setup then press and

hold the MENU button for at least 3 seconds. To exit without making any adjustments press
the MENU button. The display will lock after 30 seconds, press the MENU button for 3 sec­onds to unlock.

Please refer to the system menu on page 10 for detailed layout.

DMX Address - With this function, you can adjust the desired DMX-address via the Control Board.

1. Press the MENU button so that “Addr” is displayed, and press ENTER.

2. Press the UP or DOWN buttons The current DMX address will now be displayed.

3. Use the UP or DOWN buttons to adjust the DMX address.

4. Press ENTER to conrm or press MENU button to return to the main menu.

DMX Channel Mode - With this function, you can see the how many DMX channels the xture has.

1. Press the MENU button so that “NodE” is displayed, and press ENTER.

2. The current DMX channel mode will be displayed. The default DMX channel mode is 9 channel mode. Use
the UP or DOWN buttons to scroll to your desired DMX channel mode, and press ENTER to set it.

3. Press the MENU button to exit and return to the main menu with no changes.

DMX State - This mode can be used as a precaution mode, that in case the DMX signal is lost, interrupted,

or power is lost, the operating mode chosen in this setup is the running mode the xture will go into

when the DMX signal is lost. Note: Hold is the default setting.

1. Press the MENU button so that “Nodn” is displayed, then press ENTER.

2. Press the UP or DOWN buttons until “DMX State” is displayed, and press ENTER. Use the UP and DOWN

buttons to switch between the two modes; Blackout or Hold. Press the ENTER button to make your selection.

• blac - If the DMX signal is lost or interrupted, the unit will automatically go into stand by mode.

• Auto - If the DMX signal is lost or interrupted, the unit will automatically go into auto program mode.

• Soun - If the DMX signal is lost or interrupted, the unit will automatically go into sound active mode.

• Hold - If the DMX signal is lost the xture will stay in the last DMX setting. If power is applied and this mode

is set, the unit will automatically go into the last DMX set up. This is the default setting.

3. Press the MENU button to return to the main menu.

Master-Slave Set Up - With this function, you can see the how many DMX channels the xture has.

1. Press the MENU button so that “SLAu” is displayed, and press ENTER.

2. The current setting will be displayed. Use the UP or DOWN buttons to toggle between “Slave” (SLAu) or
“Master” (NASt), and press ENTER to select your setting.

3. Press the MENU button to exit and return to the main menu with no changes.

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 11

3D Vision Plus Operating Instructions

Auto Program - With this function, you can run an internal program. Make sure the DMX state is set to “Auto”

as well.

1. Press the MENU button so that “Auto” is displayed, then press ENTER.

2. Press the UP or DOWN buttons until “RAND” is displayed, and press ENTER. The program will now run.

3. If you would like to select a program, press the UP or DOWN buttons until “AuXX” is displayed. “XX”

represents the current program that is displayed. Use the UP or DOWN buttons to nd your desired program.

There are 16 programs to choose from.

4. Press ENTER to conrm your selection or press the MENU button to return to the main menu.

5. To adjust the program speed, press the MENU button until “SPEd” is displayed and press ENTER. Use the
UP or DOWN buttons to adjust the program speed to your desire and press ENTER to conrm.

Sound Active Mode - With this function, you can activate sound active mode.

1. Press the MENU button so that “Soun” is displayed, and press ENTER.

2. Press the UP or DOWN buttons until “RAND” is displayed, and press ENTER. The program will now run.

3. If you would like to select a program, press the UP or DOWN buttons until “SuXX” is displayed. “XX” rep-

resents the current program that is displayed. Use the UP or DOWN buttons to nd your desired sound active

program. There are 16 programs to choose from.

4. Press ENTER to conrm your selection or press the MENU button to return to the main menu.

5. To adjust the sound sensitivity, press the MENU button until “SEns” is displayed and press ENTER. Use the
UP or DOWN buttons to adjust the sensitivity to your desire and press ENTER to conrm.

Pixel Conguration - With this function, you are able to change the pixel conguration. There are 6 conguations
to choose from. Please see page 14 for the dierent congurations.

1. Press the MENU button so that “ConF” is displayed, and press ENTER.

2. The current conguration will now be displayed. Use the UP and DOWN buttons to scroll through the dier­ent congurations until you nd your desired one.

3. Press ENTER to conrm your selection or press the MENU button to return to the main menu.

Brightness Adjustment - With this function, you are able to change the output intensity.

1. Press the MENU button so that “dIEr” is displayed, and press ENTER.

2. The current setting will now be displayed. Use the UP and DOWN buttons to adjust the brightness to your
liking.

3. Press ENTER when you are nished or press the MENU button to return to the main menu.

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 12

3D Vision Plus DMX Control

Control Using a DMX Controller:

1. The 3D Vision has 3 DMX channel modes; a 3 channel mode, 9 channel mode, and 13 channel
mode. See pages 6-9 for detailed description of the DMX values and traits. See the page 15 for
the pixel configurations.

2. To set your desired DMX channel mode and DMX address follow the instructions on page 11.

3. When connecting to a DMX controller or using MyDMX, you will need to use a RJ45 to 3pin
adapter. This can be purchased through ADJ.

4. Connect the first unit to the adapater and then connect to either your DMX controller or MyDMX.

5. Follow the DMX traits on pages 6-9 to control your unit.
DO NOT daisy-chain more than 32 Panels when connecting directly to a DMX controller.

3D Vision Plus Master-Slave Configuration

Master-Slave Configuration:

This function will allows you to link units together to run in a Master-Slave set-up. In a Master-Slave
set up one unit will act as the controlling unit and the others will react to the controlling units built-in
programs. Any unit can act as a Master or as a Slave however, only one unit can be programmed to

act as the “Master.”

Master-Slave Connections and Settings:

1. Daisy chain your units via the etherCON connections located on the side of the unit.

2. Connect the rst “Slave” unit to the “Master.”

3. Press the MENU button until “SLAv” is displayed and press ENTER. For the “Master” unit press
the UP or DOWN buttons until ‘NASt” is displayed and press ENTER. This now the “MASTER”

unit.

3. Set the “Master” unit to your desired mode of operation. On the “Slave” unit’s press the MENU
button until “SLAv” is displayed and press ENTER. Press the UP or DOWN buttons until ‘SLAv” is
displayed and press ENTER. The “Slave” unit(s) will now follow the “Master”.

3D Vision Plus Multiple Unit Power Linking

With this feature you can connect the xtures to one another using the IEC input and output
sockets. The maximum that can be connected is 130 xtures @ 120V and 250 xtures @ 240V.
After the maximum connected xtures you will need to use a new power outlet.
NOTE: USE CAUTION WHEN POWER LINKING OTHER FIXTURES TO THE 3D VISION PLUS AS
THE POWER CONSUMPTION OF OTHER LIGHTING FIXTURES WILL VARY!

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 13

3D Vision Plus Pixel Configurations

In the default conguration (CONFIG 1), PIXEL #1 is located at the top section of the unit. Look for
the word TOP printed on the backside to determine the top section.

To change the position of PIXEL #1, select one the pixel congurations (1-6) in the system menu.
See ilustration below for the pixel conguration layout.

TOP TOP TOP

TOP

TOP

TOP

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 14

3D Vision Plus Mounting and Grouping

When installing the unit, the trussing or area of installation must be able to hold 10 times the weight
without any deformation. When installing the unit must be secured with a secondary safety attach­ment, e.g. included safety cable. Never stand directly below the unit when mounting, removing, or
servicing the unit.

Overhead mounting requires extensive experience, including calculating working load limits, installa­tion material being used, and perodic safety inspection of all installation material and unit. If you lack

these qualications, do not attempt the installation yourself.

The installaiton should be checked by a skilled person once a year.

To connect your 3D Visions to one another you can use a quick release panel lock (sold separately).
To use the quick release panel lock simply squeeze the ends of the quick release panel locks inwards
and attach to one of the six outer rigging bar attachment points. You can use a pro clamp with 10M
bolt attached to the rear middle of the unit (as seen below) to attach to trussing. See the next page
for all rigging areas and quick release connections.

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 15

3D Vision Plus Mounting and Grouping

10M threaded mounting hole
(to attach pro clamp to lock on truss)

quick release panel lock
to connect adjoining panels

crosshole (to
hang on a stud or

hook)

Rigging bar attachment points

PL Quick Release: SKU# 3DV175
Quick Release panel lock is used to connect the
units to one another. See page 15.

Hanging Bracket: SKU# 3DV149

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 16

3D Vision Plus Dimensional Drawing

15.93”/404.7mm

4.68”/119mm

13.80”/350.7mm

5.90”/150mm

8”/202.5mm

1.6”/40.5mm

3.16”/80.5mm

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 17

3D Vision Plus Fuse Replacement

Disconnect the unit from its power source. Remove the power cord from the unit. Once the cord has
been removed, you will find that the fuse holder is located next to the power socket. Use a philips-head
screw driver to unscrew and remove the fuse holder. Remove the bad fuse and replace with a new one.

3D Vision Plus Trouble Shooting

Listed below are a few common problems the user may encounter, with solutions.

Unit not responding to DMX:

1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on

some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right
connectors; it does matter which way the inputs and outputs are connected.

Unit does not respond to sound:

1. Quiet or high pitched sounds will not activate the unit.

2. Make sure that Sound Active mode is activated.

3D Vision Plus Cleaning

Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be car­ried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.

2. Clean the external optics with glass cleaner and a soft cloth every 20 days.

3. Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog resi­due, dust, dew).

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 18

3D Vision Plus Warranty

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

 •NonL.E.D.LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect

Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par
Cans, Trussing, Lighting Stands etc. excluding LED and lamps)

 •LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month

limited warranty)

 •L.E.D.Products=2-year(730days)LimitedWarranty(excluding batteries which have a 180 day lim-

ited warranty). Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.

 •StarTecSeries=1YearLimitedWarranty(excluding batteries which have a 180 day limited warranty).

•ADJDMXControllers=2Year(730Days)LimitedWarranty

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 19

3D Vision Plus Specifications

Model:

LEDs: 72 x 0.164W 3-in-1 LEDs
Working Position: Any safe working position
Voltage: 100V-250V, 50/60Hz
Power Draw: 13W (Full On)
Multiple Unit Power Link: 130 Units Max. (120V)
250 Units Max. (240V)

Beam Angle: 180 Degrees

Weight: 6 lbs./ 2.74Kgs.

Dimensions: 3.16” (L) x 15.93” (W) x 13.80” (H)

80.5 (L) x 404.7 (W) x 350.7 (H) mm
Warranty: 2 Year (730 days)

Please Note: Specications and improvements in the design of

this unit and this manual are subject to change without any prior
written notice.

3D Vision Plus

ADJ Products, LLC - www.adj.com - 3D Vision Plus User Manual Page 20

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: [phone] / Fax: [phone]

Web: www.adj.com / E-mail: [e-mail]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

[e-mail] / www.adj.eu

Tel: [phone] / Fax: [phone]