Ademco GPIO332 Users Manual

LT-GP-II-01
Before you begin
5.50
(139.6)
5.10
(129.4)
2.80 (71)
3.51 (89.1)
1.70
(43.3)
0.18 (4.6) MOUNTING HOLES x 4
DIN RAIL
1.4 (35)
Before installing the GP-IO-332, configure it according to the instructions in the Geopoint Hub and I/O Installation and Operation Guide (LT-GPIOG) available on the Alerton Support Network.
GP-IO-332, GP-IO-332-E
Installation Instructions
Overview
Warning! Always install equipment in accordance with the
instructions and in a manner consistent with electrical codes and the authority having jurisdiction. Read all instructions before mounting and wiring.
ATTENTION! Installez tout le matériel en conformité avec le Code national de l'électricité et d'une manière acceptable pour l'autorité locale compétente. Lisez tout instructions avant l'installation du matériel. Le non respect des instructions peut entraîner des dommages matériels ou une situation dangereuse.
The GP-IO-332 is a wireless device that eliminates the need for long cabling between a unitary controller and its physical I/O. Its multiple inputs and outputs can be concentrated onto the BACnet bus by the GP-HUB-100 receiver. These instructions will help you mount and wire the device and then verify that it functions correctly.
Mounting
Choose a mounting location that reduces interference between the GP-IO-332 and the GP-HUB. Some points to consider when selecting a location:
The effective communication range is 400 feet through open air and 100 feet through two non-metallic walls.
Any metal (ducting, equipment, metal studs, and so on) near
the device or between two devices will impede radio waves.
If a wall has metal components (studs, ductwork, and so on)
radio waves will tend to travel along the plane of the wall. Mounting the device on the same wall as other device(s) will increase signal strength.
When mounting near ductwork or other metal, use
doublesided tape to mount the device while testing radio reception.
Mount the GP-IO-332 indoors or in a weatherproof enclosure.
Important! Enclosures, if used, must not block 2.4GHz RF. Use polyester/fiberglass models. If unsure, consult the manufacturer.
DIN rail mounting
To mount the GP-IO-332 on a 35mm DIN rail
1 Hold the device with its top tilted toward the DIN
rail and then hook the two top tabs on the back of the device onto the top of the DIN rail.
2 Push down and in to snap the connector onto the
rail. To remove the GP-IO-332 from a DIN rail, push straight up from the bottom to release the top tabs and then pull the top of the device outward.
Wall mounting
To mount the GP-IO-332 on a wall, position the device in any orientation and secure it to the wall with size 6 or 8
Fig. 1 GP-IO-332 dimensions in in. (mm).
Note The GP-HUB-100 signal receiver has the same
dimensions and mounting holes as the GP-IO-332.
Specifications
Supply Voltage: 24VAC (typical), 50/60Hz. 5VA (max) Operating Temperature: -18°C to 70°C (0°F to 158°F) Operating Humidity: RH 5% to 95%, non-condensing Storage Temperatures: -40°C to 70°C (-40°F to 158°F)
© Honeywell Page 1 - Printed in USA LT-GP-II-01 Rev. A
screws appropriate for the mounting surface.
Wiring
X
X
X
X
XXX
XXXXXXX
GND
COM
24VAC
MSTP-
POWER
MSTP+
XFMR
24VAC
O/P
FUSED AC
SOURCE
PANEL GROUND
Once the GP-IO-332 is mounted, connect the power.
The RSSI LEDs also flash to indicate error conditions.
Tab le 1 RSSI Error Conditions
Flash Pattern Status
One red No communication or the device has not
joined the wireless network
One yellow and two green
Two green Multiple devices have identical wireless
One red and one green Lost communication with GP-HUB-100.
One flashing red and two solid green
Wireless network MAC address does not match device type
network MAC addresses
Working to re-establish connection.
Device initialization in progress
Fig. 2 Wiring diagram.
Connecting power
Connect the GP-IO-332 to 24VAC power from a UL Listed Class-2 24VAC transformer (not included). You can use the same transformer for the GP-HUB-100 and other associated controller(s) as long as the total load does not exceed 100VA and all devices are half-wave. The GP-IO-332 is a half-wave device.
CAUTION! Half-wave devices and full-wave devices must not use the same AC transformer. You must maintain wiring polarity. Failure to do so can result in equipment damage.
ATTENTION! Les dispositifs demi-onde et les dispositifs à onde pleine ne doivent pas utiliser le même transformateur AC. Le défaut de maintient de la polarité du câblage peut endommager l'équipement.
USB Power
The GP-IO-332 can also be powered from a USB cable that provides 5VDC power. Some USB ports can supply sufficient power and some can not. Review the user documentation for the power source to determine whether the USB port supplies sufficient power.
BO LED
BO TERMINALS AO TERMINALS
DIP Switches
The GP-IO-332 has two banks of DIP switches. The first, 6-position switch, sets the network address for the wireless network (must match GP-HUB-100). The second, 8-position switch, is used to set the Remote Device address (0-99) that the device will use when connecting to the Hub.
© Honeywell Page 2 - Printed in USA LT-GP-II-01 Rev. A
AC POWER
TERMINALS
USB
TERMINALS
AI TERMINALS
Fig. 3 Locations of GP-IO-332 components.
Loading...
+ 2 hidden pages