Ademco CTU K05 User Manual

TS TAxx

Integrated Interactive Terminals

Installation Manual

TS TAxx

Versione: 1.0 US

TABLE OF CONTENTS

FCC NOTICE...................................................................................................4

Canadian Compliance Statement...........................................................4

PRELIMINARY OPERATIONS ............................................ 5

Mounting Instructions......................................................................................5

Electrical Connections....................................................................................6

Cabling Arrangements....................................................................................7

INSTALLATION ............................................................... 8

Attaching the Terminal Support Plate............................................................8

Hooking Up the Terminal................................................................................9

Connecting the Cables..................................................................................10

Jumpers.........................................................................................................13

Auxiliary Connections...................................................................................14

Closing the Terminal.....................................................................................15

Applying the Entry/Exit Labels......................................................................16

TECHNICAL SPECIFICATIONS....................................... 17

TemaServer TS TAx3 (CTU -K03 code 1500064FA)................................17

Spare Parts............................................................................................18

TemaServer TS TAx4 (CTU-K04 code 1500087DA) ......................................19

Spare Parts............................................................................................20

TemaServer TS Tax5 (CTU-K05 code 15000...)............................................21

Spare Parts............................................................................................22

TemaServer TS Tax7 (CTU-K07 code 15000....) ...........................................23

Spare Parts............................................................................................24

Optional Parts................................................................................................25

TABLE OF CONTENTS Page 3

FCC NOTICE

NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, these is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by tuning the equipment off and on, the
user is encouraged to try to correct the interference by one or more the
following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Canadian Compliance Statement

This Class B Digital apparatus meets all the requirements of the Canadian
Interference- Causing Equipment Regulations.
Cet appareil numerique de la classe B respecte les exigences du Reglement
sur le material broilleur du Canada.

Page 4 FCC NOTICE

PRELIMINARY OPERATIONS

Mounting Instructions

It is recommended that you attach the cables to wall box. The position
selected for mounting the box must satisfy the requirements laid down for the
mounting area and allow the necessary space for opening the box (see
Figure 1). In addition, there must be sufficient space to the right and rear of
the unit to allow access to the box with a screwdriver.

encased
box

floor

tube 14cm 12cm mounting area

32cm

work area

cables

Figure 1: Space requirements for mounting

Mounting Instructions Page 5

Electrical Connections

115V 60Hz

GROUND

The TemaServer is powered at low voltage (12VAC) by means of a
transformer connected to the 115/230V 50/60Hz network switch. This switch
must be positioned prior to the TemaServer. The cables connecting the
transformer and the TemaServer must be at least AWG20 and no more than
10m long (see Figure 2).

INOUT

10m max.

yellow-green

oragne

gray

12V

transformer
module

230V 50Hz or

115/230V

125mA

black

brown

yellow-green

Figure 2: Electrical connections

Page 6 Electrical Connections

Cabling Arrangements

floor

It is recommended that you attach the cables to wall box. The box must be
placed 120cm from the ground (see Figure 3).

It is strongly recommended that you run the LAN cable into a separate tube
from the one used for the 12V∼ power cable. If you wish to keep the LAN
cable and the 12V ∼ power cable together, make sure that the 12V∼ cable is
shielded. You must not on any account attempt to route the LAN cable and
the primary power cable (230V∼) together.

encased box

tube

120 cm

cables

Figure 3: Cabling arrangements

Cabling Arrangements Page 7

INSTALLATION

anchor

Attaching the Terminal Support Plate

To attach the terminal support plate, drill two holes in the wall in which to
place the plastic anchors that hold up the support plate (see Figure 4). Make

sure that the box attached to the wall is aligned with the niche on the
lower part of the support plate (use a ∅ 6mm parallel tip flat head

screwdriver).

anchor

Figure 4: Terminal support plate

Page 8 Attaching the Terminal Support Plate

Hooking Up the Terminal

To hook up the terminal, follow the steps described below (see Figure 5):

1. Attach the upper part of the terminal to the upper hooks on the support

plate.

2. Insert the cables into the terminal through the specified openings.

3. Tighten the two screws that secure the terminal to the support plate (use a

∅ 6mm parallel tip flat head screwdriver).

1) Attach terminal to hooks

3) fasten the screws

Figure 5: Hooking up the terminal

2) Insert
cables

Hooking Up the Terminal Page 9