Ademco 8DLPLS8 USR3 Users Manual

Installation Instructions

1. Install the provided FCC/IC label on the control’s case back.

Typical FCC/IC Label Location

Removing the Bezel

Installing the communicator Module

7. Check the signal strength before permanently locating the Lyric Controller. See Checking Signal Strength section.

Security

Tools – [Master code]

Advanced

Comm. Test

Security

Tools – [installer code] –Program – Comm. Diagnostcs - [V] – Test Communication

Send Cellular Message Send Ethernet Message

c. Set the communication path to Wi-Fi-only.

When choosing a suitable mounting location, check the

Security

Tools – [installer code]

Program

Comm. Diagnostics

Cellular Information

Signal Strength Guide

Panel display signal strength:

AlarmNet 360 Display

PRELIMINARY

Lyric-LTE Series

Communicators

General Information

The Lyric-LTE series Communication Modules allow the Lyric Controller to communicate with the Central Station via the cellular radio network. The Lyric-LTE series includes the following models:

• LYRICLTE-V (US, Verizon network)

• LYRICLTE-A (US, AT&T network)

Installing the Module (First Time Installation)

• LYRICLTE-C (Canada)

FIRST TIME INSTALLATION NOTE: Before performing the first time installation of the communication module,

make sure power (both AC and battery) is removed from the controller and follow the Installing the Module (First Time Installation) steps.

LYRICLTE-A & LYRICLTE-C: 800-22830

LYRICLTE-V: 800-22830-1

2. Remove bezel from right-hand side of control to expose the communication module slot. To remove the bezel, push upward then slide it out.

3. Insert the module into the slot. Push firmly to mate the edge connector.

4. Replace the bezel.

5. After all other connections are made, power up the controller.

6. Program and register the module during the controller’s initial association with its AlarmNet 360™ account. Refer to the controller’s Programming Guide for details.

8. Test the communication paths.

Master User:

Installer:

Press Press “Ack Received” indicates successful communication.

–

. Wait for “Ack Received” message.

If acknowledgement is not received, try one of the following: a. Use an external antenna (see Using an External Antenna section). b. Replace the radio with an alternate technology radio (ex., try 3G or CDMA).

Checking Signal Strength

communicator’s signal strength to ensure proper operation. For most installations, using the module’s internal antenna, mounting the Lyric controller as high as practical, and avoiding large metal

should be minimum 2 bars

components provides adequate signal strength. Use the Lyric Controller “Cellular Information” screen to display

signal strength (in number of bars):

–

Must be minimum 2 bars lit.

–

Compare the signal strength number of bars displayed to the

Signal Strength Guide values at right to ensure adequate signal strength.

If using AlarmNet 360, check that the display is minimum 2 bars.

If necessary, relocate the Controller to obtain better signal strength (press

again to refresh the reading).

If adequate signal strength cannot be achieved, an external antenna should be used. See Using an External Antenna section on the other side.

range of 1-5bars;

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

Communication Module Replacement

This procedure is intended only for replacement of existing communication modules previously installed and registered in the Controller.

1. Select the Install Cellular Module button.

Security –Tools

[master code] – Advanced – Install

Cellular Module

Security

Tools – [installer code]

Test – Install Cellular

Module

Yes

Replacing the Module

IMPORTANT NOTE ABOUT EXTERNAL ANTENNAS

SUPPORT & WARRANTY

Specifications

Dimensions: ....

Voltage Input

Current

Environmental

Lyric LTE series Frequency Bands

PRELIMINARY

800-21995 3/17 Rev. B

In the event the communication module needs to be replaced, the Lyric Controller must first be put in module replacement mode (“Install Cellular Module”) to avoid causing a tamper alarm or damaging the module. Module replacement mode deactivates tamper protection and removes power from the module connector for about 15 minutes.

Master User:

Installer:

a. Select b. A popup window displays steps for module replacement.

Keep this window open until replacement is completed

2. Remove the side bezel. See diagram at right.

3. Remove the communication module from its connection slot by using the pull tab.

4. Insert the new module into the slot. Push firmly to mate the edge connector.

5. Replace the bezel.

6. When installation is complete, press OK at the replacement steps window. Confirmation of proper installation appears. Press OK to exit.

7. Test the communication path. See step 8 in Installing the Module section.

sing an External Antenna

If an external cellular radio antenna is used, the antenna may be installed or replaced ONLY by a professional installer.

–

at the prompt to continue.

–

TO THE INSTALLER - Lyric-LTE Series

This device is to be used in mobile or fixed applications only. For mobile and fixed operating configurations the antenna gain, including cable loss, must not exceed 3.25 dBi (US) or 0.6 dBi (CA) in the 850 MHz band, 5.5 dBi in the 1700 MHz band, and 2.5 dBi in the 1900 MHz band for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and EIRP power limits as specified in Parts 22H and 24E and 27.

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 in (20 cm) from all persons and must not be co-located or operated in conjunction with any other transmitter except in accordance with FCC multi-transmitter product procedures.

ition aux Fréquences Radio: L'antenne (s) utilisée

Expos émetteur doit être installée à une distance de séparation d'au moins 7,8 pouces (20 cm) de toutes les perso

If adequate signal strength cannot be achieved with the internal

antenna, an external antenna can be employed. A kit with an internal adapter cable, clamp and bracket will be required and is available. A connection diagram is provided in the kit which shows how to connect a typical antenna to the device.

RF EXPOSURE WARNING

Mise en Garde

nnes.

–

2-5/8”W x 3-1/8”L x 1/2”D

.. 5V (provided by the controller)

LyricLTE-A / LyricLTE-C:

Idle ........................ 45mA, standby

Transmit max. .. 245mA RMS

LyricLTE-V:

Idle ........................ 45mA, standby

Transmit max. .. 245mA RMS

pour cet

Operating temperature: -20ºC to +55ºC, (for compliance agency: 0ºC to +49ºC) Storage temperature: -40º to +70ºC Humidity: 0 to 95% relative humidity, non-condensing

(for compliance agency 0% to 85%)

LyricLTE-V:

PLS8-V LTE: Triple band, 700 (Bd13) / AWS (Bd4) /

1900MHz (Bd2)

LyricLTE-A, LyricLTE-C:

GSM/GPRS/EDGE: Quad band,

850/900/1800/1900MHz

UMTS/HSPA+: Triple band, 850 (BdV) /

AWS (BdIV) / 1900MHz (BdII)

LTE: Quad band, 700 (Bd17) /

850 (Bd5) / AWS (Bd4) / 1900MHz (Bd2)

CABLE KIT: 100-05310

FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void

For patent information, see www.honeywell.com/patents

Ê800-21995yŠ

800-21995 2/17 Rev. A

For the latest documentation and online support information,

please go to: https://mywebtech.honeywell.com/

For the latest warranty information, please go to:

www.honeywell.com/security/hsc/resources/wa.

the user's authority to operate the equipment.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and RSS-210 of IC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.