Ademco 8DLLSD500 Users Manual

This wireless heat / smoke
Smoke Detector
Open
/ OPEN OPEN / OPEN
NOTE
FC: NOTE
SP: NOTE
PA: NOTE
Enroll / Enroll / Enroll / Enroll
To silence the detector:
-
NOTE: After enrolling and before mounting permanently,
FC: NOTE
SP: NOTE
PA: NOTE
Mount / Mount /
Mount / Mount
NOTE
NOTE
go mode, all smoke detectors in the
NOTE
go mode, all smoke detectors in the
NOTE
all smoke detectors in the
Use UL/ANSI Approved canned smoke. / Use UL/ANSI Approved canned smoke.
Test / Test
/
Test / Test
AGENCY STATEMENTS ARE AT THE BOTTOM OF PAGE 2
detector is intended for use with Honeywell controls that support SiX™ series devices.
is intended for use with
Honeywell controls that support SiX™ series devices.
SP: This wireless heat / smoke detector is intended for use with Honeywell controls that support SiX™ series devices.
PA: This wireless heat / smoke detector is intended for use with Honeywell controls that support SiX™ series devices.
: Once enrolled, the device cannot be used with another system until it is removed from the current controller. See the controller’s instructions,
device cannot be used with another system until it is removed from the current controller. See the controller’s instructions,
device cannot be used with another system until it is removed from the current controller. See the controller’s instructions,
device cannot be used with another system until it is removed from the current controller. See the controller’s instructions.
: Once enrolled, the
: Once enrolled, the
: Once enrolled, the
Press the test switch or disarm the system at the controller. If the alarm condition continues, the detector is only quiet for 5 minutes. When programmed in one-go all-go mode, the test switch will not silence the detector.
conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary.
permanently, conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary.
permanently, conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary.
permanently, conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary.
: After enrolling and before mounting
: After enrolling and before mounting
: After enrolling and before mounting
For programming Smoke or Heat alarms and Tamper, see the Controller’s instructions.
: All smoke detectors programmed in the panel to operate in one-go-all-go mode will
sound on alarm.
FC: For programming Smoke or Heat alarms and Tamper, see the Controller’s instructions.
: If programmed in the panel to operate in one-go-all-
system will sound on alarm
SP For programming Smoke or Heat alarms and Tamper, see the Controller’s instructions.
: If programmed in the panel to operate in one-go-all-
system will sound on alarm
PA: For programming Smoke or Heat alarms and Tamper, see the Controller’s instructions.
: If programmed in the panel to operate in one-go-all-go mode,
system will sound on alarm
*Use UL/ANSI Approved canned smoke. / Use UL/ANSI Approved canned smoke. /
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Ê800-15961PŠ
LEDS and 85dB SOUNDER / LEDS and 85dB SOUNDER / LEDS and 85dB SOUNDER
/ LEDS and 85dB SOUNDER
R
G
Sounder
Status
Power Up – Enrollment
Power Up – Device enrolled /
Normal mode or Communicating
with the panel
Maintenance1 / Maintenance1 /
Smoke Alarm
Low Battery / Low Battery /
Low Battery / Low Battery
Tamper Activated /
Starts chirping after 7 days, continues until the batteries are replaced or die
BATTERY CAUTION: Risk of fire,
BATTERY CAUTION
Replace Battery /
Replace Battery / Replace Battery
SP: BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above
BATTERY CAUTION
Approval Listings:
Specifications:
Range: RF Frequency Battery
Tamper Operating Temperature Relative Humidity
Dimensions
ick / 96 mm Diameter x 29mm
Product must be tested at least once each year / Le fonctionnement du produit doit être vérifié au moins une fois par année / El producto debe ser probado al menos una vez al año / O produto deve ser testado pelo menos uma vez por ano
Support / Support / Support / Support
U.S. warranty / U.S. warranty / U.S. garantie / U.S. garantia
FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation
FCC / IC STATEMENT
RF Exposure Warning
Mise en Garde Exposition aux Frequences Radio:
explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries properly. Keep away from children.
FC: explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep
Power Up – Enrollment /
Power Up – Enrollment / Power Up – Enrollment /
Power Up – Device enrolled / Power Up – Device enrolled/
away from children.
212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children. PA:
212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children.
: Risk of fire,
: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above
Power Up – Device enrolled
FCC / IC
with the panel/
Normal mode or Communicating with the panel / Normal mode or Communicating
ETL Listed to UL639 cETL Listed to ULC S306-03
RoHS
with the panel / Normal mode or Communicating
Maintenance
Test Alarm2 / Test Alarm2 /
Test Alarm
Heat Alarm3 / Heat Alarm3 /
Heat Alarm
1 /
Maintenance1
2
/ Test Alarm2
3
/ Heat Alarm3
https://mywebtech.honeywell.com/
0’- 25’/ 0 – 7.6m; Selectable
: 2.4GHz
: 2 x 3V, Lithium; Panasonic CR123A, Duracell DL 123,
Duracell DL 123A, Honeywell 466
: Wall
: 32° – 95° F / 0° – 35° C
: 95% max. (Agency Compliance – 93% max.),
non-condensing
: 3.78” Diameter x 1.14” Th
Thick
Smoke Alarm /
Smoke Alarm / Smoke Alarm /
www.honeywell.com/security/hsc/resources/wa
MyWebTech
Warranty
4
Tamper Activated / Tamper Activated / Tamper Activated
1
See Maintenance Section/ See Maintenance Section / See Maintenance Section /See Maintenance Section
2
Test activated by the test switch or from the panel / Test activated by the test switch or from the panel / Test
activated by the test switch or from the panel / Test activated by the test switch or from the panel
3
135° F / 57° C or Temperature rise of 15° F ( 8.33° C) within 1 minute / 135° F (57° C) or Temperature rise of ≥15°
F (8.33° C) within 1 minute / 135° F(57° C) or Temperature rise of 15° F (8.33 ° C) within 1 minute /
4
Starts chirping after 7 days, continues until the batteries are replaced or die / Starts chirping after 7 days, continues
until the batteries are replaced or die / Starts chirping after 7 days, continues until the batteries are replaced or die /
2014 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved
www.honeywell.com/security
Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une reception indésirable.
least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
distance de séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation
The antenna(s) used for this device must be installed to provide a separation distance of at
L'antenne (s) utilisée pour cet émetteur doit être installée à une
800-15961 11/15 Rev C BETA2
Loading...