Ademco 8DLLMD500 Quick Install Manual

This wireless passive infrared motion

Motion Sensor Open /

Open / Open

NOTE

FC: NOTE

SP: NOTE

PA:

Enroll / Enroll / Enroll / Enroll

Mounting Locations / Mounting Locations /

Mounting Locations / Mounting Locations

NOTE

FC: Note

SP: Note

PA: Note

Mounting Options / Mounting Options /

Mounting Options / Mounting Options

PLEASE SEE BOTTOM OF PAGE FOR FCC/IC AGENCY STATEMENTS

sensor is intended for use with Honeywell controls that support SiX™ series devices.

FC: This wireless passive infrared motion sensor

is intended for use

with Honeywell controls that support SiX™ series devices.

SP: This wireless passive infrared motion sensor is intended for use with Honeywell controls that support SiX™ series devices.

PA: This wireless passive infrared motion sensor is intended for use with Honeywell controls that support SiX™ series devices.

: Once enrolled, the sensor cannot be used with another system until it is removed from the current controller. See the controller’s instructions.

cannot be used with another system until it is removed from the current controller. See the controller’s instructions.

be used with another system until it is removed from the current controller. See the controller’s instructions.

: Once enrolled, the sensor

Once enrolled, the sensor cannot

: After enrolling and before mounting permanently, conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary.

controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary.

: After enrolling and before mounting permanently, conduct Go/No Go tests (see

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

Ê800-15963bŠ

Walk Test / Walk Test / Walk Test / Wal

NOTE: Before using Test Mode, the device must first be enrolled in the controller.

NOTE: To enter Test Mode, the device must first be enrolled in the controller. NOTE: To enter Test Mode, the device must first be enrolled in the controller. NOTE: To enter Test Mode, the device must first be enrolled in the controller.

Detection Patterns / Detection Patterns /

Detection Patterns / Detection Patterns

Approval Listings:

Specifications:

Range: Wall Mounting Height: Battery

RF Frequency Tamper Operating Temperature

Relative Humidity

Dimensions

Product must be tested at least once each year / Le fonctionnement du produit doit être vérifié au moins une fois par année / El producto debe ser probado al menos una vez al año / O produto deve ser testado pelo menos uma vez por ano

Replace Battery / Replace Battery /

Replace Battery / Replace Battery

NOTE:

NOTE: NOTE: NOTE:

FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation

FCC / IC STATEMENT

RF Exposure Warning

Mise en Garde Exposition aux Frequences Radio:

Zones / Zones / Zonas / Zonas

Lower / Courtes /

Cercana/ Mais baixas

Intermediate /

Intermédiaires / Intermedia / Intermédias

Long / Longues / Largo

Alcance / Longo alcance

FCC / IC SIA-PIR-01 ETL Listed to UL639 cETL Listed to ULC S306-03

RoHS

www.honeywell.com/security

40’ x 56’ / 12 m x 17 m

: 1 x 3V, Lithium; Panasonic CR123A, Duracell DL 123A,

Duracell DL 123, Honeywell 466

Compliance 32° – 120° F / 0° – 49° C)

non-condensing

x 41 mm D

: 2.4GHz

: Cover and Wall – reported separately to panel.

: 4.13” H x 2.38” W x 1.61” D / 105 mm H x 60.4 mm W

7’ – 9’ (2.1 m – 2.7 m); Optimal 7’6” (2.3 m)

: 32° – 122° F / 0° – 50° C (Agency

: 95% max. (Agency Compliance - 93% max.),

To conserve battery life, the sensor is active only when the system is armed.

To conserve battery life, the sensor is only active when the system is armed. To conserve battery life, the sensor is only active when the system is armed. To conserve battery life, the sensor is only active when the system is armed.

BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries properly. Keep away from children.

FC:BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children.

SP: BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children.

PA: BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children.

Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une reception indésirable.

least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.

distance de séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

– The antenna(s) used for this device must be installed to provide a separati on distance of at

L'antenne (s) utilisée pour cet émetteur doit être installée à une

Support / Support / Support / Support

https://mywebtech.honeywell.com/

U.S. warranty / U.S. warranty / U.S. garantie / U.S. garantia

www.honeywell.com/security/hsc/resources/wa

MyWebTech

Warranty

800-15963 11/15 Rev B BETA2