Ademco 8DLLGB500 Installation guide

This wireless glassbreak detector is intended for use with

RF6GB

Note

FC: Note

SP: Note

PA: Note

Enroll / Enroll / Enroll / Enroll

LEDS / LEDS / LEDS /

LEDS

Mounting Locations / Mounting Locations /

Mounting Locations / Mounting Locations

Mounting Options / Mounting Options /

Mounting Options / Mounting Options

Red

Status

visible during Normal Mode / The LEDs are not visible during Normal Mode

BETA QUICK INSTALL GUIDE – 01/12/15

PLEASE GO TO THE BOTTOM OF THE NEXT PAGE FOR FCC/IC AGENCY STATEMENTS

Honeywell controls that support SiX™ series devices.

FC: This wireless glassbreak detector is intended for use with Honeywell controls that support SiX™ series devices.

SP: This wireless glassbreak detector is intended for use with Honeywell controls that support SiX™ series devices.

PA: This wireless glassbreak detector is intended for use with Honeywell controls that support SiX™ series devices.

: Once enrolled in a system, the RF6GB cannot be used with another control panel until it is removed from the current control panel. See the Control’s instructions device removal instructions.

system, the RF6GB cannot be used with another control panel until it is removed from the current control panel. See the Control’s instructions for device removal instructions.

: Once enrolled in a

Test Mode is 10 minutes. / Test Mode is 10 minutes / Test Mode is 10 minutes / Test Mode is 10 minutes

The LEDs are not visible during Normal Mode / The LEDs are not visible during Normal Mode / The LEDs are not

Test Mode1

Event detected during Test Mode

Alarm detected during Test Mode

Low Battery detected during Test Mode

Power Up / Tamper switch pressed / FG-701 Activated before enrollment

Tamper Detected

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

Ê800-15959)Š

Note: After enrolling and before mounting

FC: Note

SP: Note

PA: Note

Mount / Mount / Mount / Mount

Sensitivity

Setting

Approximate

Range

Program / Program /

Program / Program

Approval Listings:

Specifications:

Range: RF Frequency Battery

Tamper Operating Temperature Relative Humidity Dimensions

Product must be tested at least once each year / Le fonctionnement du produit doit être vérifié au moins une fois par année / El producto debe ser probado al menos una vez al año / O produto deve ser testado pelo menos uma vez por ano

Replace Battery / Replace Battery /

Replace Battery / Replace Battery

Support / Support / Support / Support

U.S. warranty / U.S. warranty / U.S. garantie / U.S. garantia

FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS

FCC / IC STATEMENT

RF Exposure Warning

Mise en Garde Exposition aux Frequences Radio:

permanently, conduct Go/No Go tests (see control’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary.

: After enrolling and before mounting

Consult the Control’s instructions to program the RF6GB Services: Tamper Switches, Sensitivity Setting and Temperature Sensing

FC: Consult the Control’s instructions to program the RF6GB Services: Tamper Switches, Sensitivity Setting and Temperature Sensing.

SP: Consult the Control’s instructions to program the RF6GB Services: Tamper Switches, Sensitivity Setting and Temperature Sensing.

PA: Consult the Control’s instructions to program the RF6GB Services: Tamper Switches, Sensitivity Setting and Temperature Sensing.

High * 4.6-7.6m / 15-25 ft.

Medium 3-4.6m / 10-15 ft.

Low 1.5-3m / 5-10 ft.

Lowest 0-1.5m / 0-5 ft.

* Factory default / Valeurs par défaut du fabricant / Defecto d e fábrica / Padrão de fábrica

BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children.

FC:BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children. SP: BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children. PA: BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children.

http://www.security.honeywell.com/hsc/resources/MyWebTech/

www.honeywell.com/security/hsc/resources/wa

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.

MyWebTech

Warranty

FCC / IC UL639 ULC S306-03

RoHS

0’- 25’/ 0 – 7.6m; Selectable

: 2.4GHz

: 1 x 3V, Lithium; Panasonic CR123A, Duracell DL 123,

Duracell DL 123A, Honeywell 466

: Cover and Wall

29mm Thick

: 3.78” Diameter x 1.14” Thick / 96 mm Diameter x

: 32° – 122° F / 0° – 50° C

: 5 – 95%, non-condensing

www.honeywell.com/security

This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une reception indésirable.

– The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.

séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de

P/N 800-15962 01/15 Rev BETA