Ademco 8DL-GRIPDF1, 8DL-GRIPDF User Manual

wireless motion detectors

Disarm

which may

ADT

ADT2X1

6AIO

SERIES

SECURITY SYSTEMS

SYSTEM LED FUNCTIONS

LED Status Meaning

POWER Green – Steady AC Connected/Battery Charged

Red – Blinking Low Battery Off No AC Power

STATUS Green – Steady System is Ready to Arm

Red – Steady System Armed Red – Flashing Alarm or Alarm Memory Red – Flashing Alternately with TROUBLE LED

(Flashing Amber) Off System is Not Ready to Am

TROUBLE Amber – Steady System Trouble

Amber Flashing Device Trouble Amber – Flashing Alternately with STATUS LED

(Flashing Red) Off Normal System Status (No

System is in Programming Mode

Troubles Present)

TESTING THE SYSTEM

Using the Test mode allows each detection point to be checked for proper operation. Testing should be conducted weekly to ensure proper operation.

• The keypad sounds a single beep about every 60 seconds as a reminder that the system is in the Test mode.

• Alarm messages are not sent to Central Station when Test mode is on.

If a problem is experienced with any detection point (no confirming sounds, no display), call for service immediately.

Disarm the system and close all protected windows, doors, etc. The READY indicator light should come on if all zones are intact

Enter 4-digit Master code +

3. Listen. The external sounder should sound for about 1 second then

turn off. If the sounder does not sound, CALL FOR SERVICE. The “Test in Progress” display appears only on the keypad that started the test.

4. Fault zones. Open each protected door and window in turn and listen

for three beeps from the keypad. Each faulted detection point should appear on the display. The display clears when the door or window is closed.

5. Walk in front of any interior motion detectors (if used) and listen for

three beeps. Each detector should appear on the display when it is activated. The display clears when no motion is detected. Note that if

between activations to conserve battery life.

Test all smoke detectors, following the manufacturer's instructions.

When all detection points have been c

are used, there is a 3-minute delay

(closed), there should be no zone numbers displayed.

Exit test mode 4-digit code +

(walk)

hecked and are intact

COMMUNICATION TEST

Perform a Communication Test to verify the communication paths to the Central Station are working properly.

Enter 4-digit Master code +

SHUTTING DOWN/REBOOTING THE SYSTEM

Hard Reboot

To avoid corrupting the control’s memory, before removing power from the system perform the following:

the system

Enter 4-digit Master code +

Wait until all of the LEDs are blank before removing power

Soft Reboot

Perform the following, if instructed by an ADT Service Representative.

Enter 4-digit Master code +

Ê800-243440Š

800-24344 4/18 Rev A Part 1

TROUBLE CONDITIONS

The word CHECK on the keypad's display, accompanied by a "beeping" at the keypad, indicates a trouble condition in the system at the displayed zone number sensor and requires your attention. Determine if the zone(s) displayed are intact and make them so if they are not. If the display persists, CALL FOR SERVICE.

To silence the beeping for these conditions, press any key.

Typical Trouble conditions include the following:

Trouble Message Meaning

COMM. FAILURE (or FC)

SYSTEM LO BAT (or BAT with no zone No.)

LO BAT+ zone descriptor (or BAT with zone No.)

Rcvr Jam (or CHECK 90) RF interference in wireless system

ALARM 1xx (or 91) FAULT 1xx CHECK 1xx

MODEM COMM (or CC) Indicates that the control is on-line with the

AC LOSS (or NO AC) The system is operating on battery power

TELCO FAULT (or CHECK 94) The telephone line has a problem. Busy-Standby (or dI) If this message remains displayed for more

A failure has occurred in the telephone communication portion of your system.

Low system battery condition exists.

Low battery condition in the wireless transmitter. Either replace the battery yourself, or CALL FOR SERVICE.

impede reception from wireless sensors. A communication problem between the

control and a connected device (e.g., RF receiver, zone expander) where the “xx” indicates the device address.

Central Monitoring Station's remote computer.

only due to an AC power failure.

If only some lights are out on the premises,

check circuit breakers and fuses and reset or replace as needed.

than 1 minute, system is disabled. CALL FOR SERVICE.

NOTES

SERVICING INFORMATION

Your local ADT Installer is the person best qualified to service your alarm system. Arranging some kind of regular service program with him is advisable.

Name:

Address:

Phone:

AD T S e cu r it y S e rv i c e s

15 0 1 Y am a to Ro a d

Bo c a R at o n, FL 33 4 31

Quick Guide to User Functions

User Guide Available Online: This Quick Guide describes the most frequently used features and functions of your system. For full details of all user functions, please see the system’s User Guide located online at: https://www.adt.com/help/faq/system- user-guides (see ADT ADT2X16AIO Series Security System User Guide P/N 800-24342 or higher). The full version User Guide is also available from your installer upon request.

Congratulations on your ownership of an ADT Security System. This system provides:

• Three forms of detection: burglary, fire and emergency (see your installer for which forms of detection are installed)

• At least one keypad which provides control of system and displays system status

• Various sensors for perimeter and interior burglary detection

• Optional smoke or combustion detectors designed to provide early warning in case of fire.

Your system may also be programmed to automatically send alarm and status messages to a Central Monitoring Station.

SYSTEM BASICS

The following is a list of some of the most common features and functions of your system:

• Several modes of burglary detection: Stay, Night-Stay, Away, Instant, Maximum.

• Bypass feature lets you bypass selected zones while leaving the rest of the system armed.

• Chime mode alerts you to the opening of protected doors and windows while the system is disarmed.

• Fire and carbon monoxide detection are always active (if installed); an alarm sounds if a fire or carbon monoxide condition is detected.

• Fire, Police and Personal Panic keys (if programmed) let you manually initiate fire and personal alarms using the keypad.

• 4-digit security codes are used in conjunction with keypad commands to perform system functions.

• Each user can be assigned a different security code, each with different authority levels.

• The system sensors have been assigned to various “zones,” which are specific areas of detection (e.g., front door, kitchen window, etc.).

• Zone numbers (points of detection) are displayed at the keypad when an alarm or trouble condition occurs.

• Partitions provide independent areas of detection, with each partition containing a group of zones that can be armed and disarmed without affecting other zones or users.

ENTRY/EXIT DELAYS

• Entry Delays give you time to disarm the system when you enter through the designated entrance door.

• You must disarm the system before the entry delay period ends, or an alarm will occur (keypad beeps during the entry delay period, reminding you to disarm the system).

• Exit delay gives you time after arming the system to leave through the designated exit door(s) without setting off an alarm. If programmed, a slow beeping will sound during the exit delay period until the last 10 seconds, which then changes to fast beeping (alerting you to the end of exit delay). If you cannot leave within this delay time period, you should stop, disarm the system, and start over to avoid a false alarm.

•••• See your installer for your delay times. See the full User Guide for details on Exit Error alarms.

NOTES ON BURGLARY DETECTION

• The system must be armed before the burglary detection can sense intrusions.

• To arm your system, enter your security code followed by the desired arming key.

• To disarm the system, enter your security code then press the OFF key.

• When an alarm occurs, the keypad sounds and displays the zone(s) causing the alarm. The external sounder may also sound.

• If your system is connected to a Central Monitoring Station, an alarm message is also sent (delayed 30 seconds by default to reduce false alarms).

• To stop the alarm sounding, simply disarm the system.

• Memory of Alarm: When an alarm condition occurs, the

keypad displays the number(s) of the zone(s) that caused the problem, and displays the type of alarm. Clear the Memory of Alarm display by entering another “off” sequence.

IMPORTANT: If you return to the premises and the main burglary sounder is on, or the keypad beeps rapidly upon entering the premises, it indicates that an alarm has occurred during your absence and an intruder may still be on the premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location.

NOTES ON FIRE AND CO DETECTION

• Your fire alarm system (if installed) is on 24 hours a day, for continuous detection. In the event of an emergency, the smoke and heat detectors sound their alarms, triggering a loud, interrupted pulsed sound from the Keypad(s) and any external sounders.

• You can silence the alarm at any time by pressing the OFF key (the security code is not needed to silence fire alarms).

• Carbon monoxide (CO) detectors, if installed, provide continuous detection. If a high level of carbon monoxide is detected, an interrupted pulsed alarm sound occurs at the keypads and the detector(s). Immediately move to a spot where fresh air is available, preferably outdoors. From a safe area, call your security service provider for further instructions. To silence the keypad sounding, press the OFF key. To silence the detector, see its instructions.

•

memory of alarm displays

Action

Press these keys…

What happens

•

again.

•

key, and then

CANCEL

Action

Press these keys…

What happens

•

To activate a Panic Function:

Desired panic function within 10 seconds

POW ER

STAT US

CAN CEL

PAN IC

OF F

CO DE CH IMEIN STAN T

RE ADY

TE ST BY PASSMA X

STAYAWAY

2 31

5 64

8 97

0 #

TR OUB LE

Icon & Text

Function

Icon & Text

Function

CANCEL

ARMING THE SYSTEM, CHIME MODE, and CONTROLLING DEVICES

Before arming, close all perimeter doors and windows and make sure the Ready to Arm message is shown. After arming, leave the premises through an entry/exit door during the exit delay period and be sure the door is reclosed to avoid causing an alarm.

Action

Press these keys… When to use an arming mode and what happens

Used when you want to arm the system with persons

staying inside (or if you have pets that are moving

Stay

4-digit code + three beeps confirm

throughout the premises).

• Arms perimeter zones; interior zones left disarmed.

• An alarm sounds if any protected window or non-

entry/exit door is opened.

Use NIGHT-STAY mode to provide increased

security while staying inside.

• Arms same as STAY mode, but also arms preselected interior sensors (set by your installer).

If programmed, used when staying inside and do not

expect anyone to use an entry/exit door.

• Same as STAY mode, except entry delay is off.

• An alarm sounds same as STAY mode, and sounds

upon opening entry/exit doors.

Used when nobody is staying inside (including pets).

• Arms the entire system (interior and perimeter).

• An alarm sounds if a protected window or any non-

entry/ exit door is opened, or if any movement is

Night-Stay

Instant

Away

4-digit code + three beeps confirm

4-digit code + two beeps confirm

detected inside.

If programmed, used when leaving the premises for

Maximum

4-digit code +

two beeps confirm

extended periods (e.g., vacation).

• Same as Away mode, except entry delay is off.

• An alarm sounds same as Away mode, and sounds

upon opening entry/exit doors.

Quick Arming

If programmed, you can press the [#] key in place of

your security code when arming the system

Alerts you to the opening of a perimeter door or

Chime Mode

DISARMING THE SYSTEM AND SILENCING ALARMS

The

OFF key is used to disarm the system, silence alarm and trouble sounds, and clear

(enter again to turn Chime mode off)

4-digit code +

window while the system is disarmed.

• Three tones sound at the keypad whenever a perimeter door or window is opened (interior zones do not produce a tone when they are faulted).

• Pressing the READY key displays the open zones.

System is disarmed and alarm sounding is silenced.

• To clear the memory of alarm display (if present), enter

Disarm and Silence Alarms

4-digit code +

• To Silence a Fire Alarm or Carbon Monoxide Alarm Simply

Press the

key (no code needed)

When entering codes and commands, sequential key depressions must be made within 10

seconds of one another. If 10 seconds elapse without a key depression, the entry will be aborted and must be repeated from its beginning.

• If you make a mistake while entering a security code, stop, press the

start over. If you stop in the middle while entering a code, and then immediately start the entry over, an erroneous code might be entered.

CANCELING ALARMS

In the event that an alarm has occurred entering the

(when done within the SIA time window)

Notes: Entering the 4-digit code will disarm the system and silence the sounder The timeout between entering the 4-digit code and (Cancel) or (1) is 10 seconds.

+ 4-digit code will silence the bell and send a cancel report to the Central Station

To clear alarm memory enter the

Note: Entering

code +

4-digit code +

+ code will have no effect.

4-digit code +

code +

4-digit code +

+ code

CHECKING OPEN ZONES

Checking Zones: Before arming your system, all protected doors, windows and other detection zones must be closed or bypassed; otherwise the keypad displays "Not Ready." GOTO: If the user is authorized, a keypad in one partition can be used to perform system functions in the other partition by using the GOTO command. Must use an Alpha keypad.

Check Zones

GOTO

BYPASSING ZONES

number (1,2,3 = go to partition; 0 = return to home part.)

4-digit code +

+ partition

The Bypass feature allows you to arm your system with one or more zones intentionally unprotected. The system must be disarmed first. Up to 5 zones can be bypassed.

Displays all faulted zones.

The keypad beeps confirming partition change.

• Keypads automatically return to their original partition after 30 seconds with no keypad activity.

Action Press these keys… What happens

When finished, the keypad will momentarily display a "Bypass"

message for each bypassed zone number. Wait for all bypassed zones to be displayed.

• Arm the system as usual. When armed, the arming message

Bypass Zones

4-digit code + 3-digit zone number(s)

to be bypassed

is displayed with “ZONE BYPASSED.”

• Bypassed zones are unprotected and will not cause an alarm if violated.

• The system will not allow fire zones to be bypassed.

• Zones are automatically unbypassed when the system is

disarmed.

• To display bypassed zones prior to arming, enter your security code and press the BYPASS key.

SECURITY CODES

Your installer assigned a master code that is used to perform all system functions. In addition, other security codes can be assigned for use by other users.

• Only the System Master and Partition Master can assign security codes to users.

• Users are identified by 2-digit user numbers.

• Only the System Master can change user partitions.

• In addition to a security code, each user is assigned an authority level and various system

attributes. See the full User Guide for definitions of each Authority Level.

• Security codes can be used interchangeably within a partition when performing system functions (a system armed with one security code can be disarmed by a different security code), with the exception of the Guest and Arm Only codes.

• Security code programming involves these steps:

1. Choose a user number from the set of users assigned to the partition in which the user will be

operating, and assign a 4-digit security code.

2. Assign an authority level to that user.

3. Assign other attributes as necessary.

Assigning Security Codes and User Attributes

The following lists the various command strings for adding security codes and attributes.

Note: Partition Master codes apply only to those user numbers previously assigned (by the system

master/installer) to the partition master’s partition.

Function

Change System Master Code

Add Security Code

Delete Security Code

Authority Level

User’s Partition

Commands

System Master code +

Master code + The Keypad beeps once to confirm that new user was added.

Master code +

+ user no. + new user’s security code

+ [user no.] +

+ new code + new code again

The security code and all attributes* set for this user number, including any associated RF keys, are erased from the system. (*except assigned partition)

Master code +

+ [user no.] +

+ auth. level

Authority Levels: 0 = standard user 3 = duress 1 = arm only 4 = partition master 2 = guest

System Master Code +

+ [user no.] +

+ part. +

This assigns the partitions the user can access. If more than one, enter partition numbers sequentially, then press [#] to end.

E.G. master code +

+ [user no.] +

Gives the user access to partitions 1 and 2 and common partition. Partition Entries: 1 = partition 1 and common 2 = partition 2 and common

3 = common partition only

PANIC KEYS

Your system may have been programmed to use special keys or key pairs to manually activate emergency (panic) functions as follows:

Function

Silent Alarm silent alarm

Sends This Signal* With This Sounding…

no audible alarm; displays, “Press [∗] to show faults,” indicating that a silent alarm has been initiated.

Audible Alarm audible alarm

a loud, steady alarm at keypad(s) and at any external sounders that may be connected.

Personal Alarm auxiliary alarm

steady alarm sound at keypad(s), but not at external bells or sirens.

Fire Alarm

All panic functions send signals to the Central Monitoring Station, if connected.

Press

fire alarm

temporal (pulsing) sound at external bells and sirens.

Keys Zone Function

995 Fire

999 Police

996 Personal

KEY/LED FUNCTIONS

TEST

BYPASS

Police Panic key

INSTANT

CODE

CHIME

READY

POWER

STATUS

TROUBLE

CANCEL

AWAY

STAY

PANIC

OFF

System Power LED*

System Status LED*

System Trouble LED*

Cancel key

Arm Away key

Army Stay key

Panic Alarm key

Disarm key

Fire Panic key

MAX

Arm Maximum key (No Delay)

* See SYSTEM LED FUNCTIONS for additional information.

System Test key

Bypass Zone key

Arm Instant key (No Delay)

Add Security Codes key

Chime Mode key

Personal Panic key

Check Zones key

Quick Arm key