Ademco 8DL6RPT Manual SiXREPEATERA QIG

SiXREPEATERA

Quick Installation Guide

panel. The control then responds accordingly (arm/disarm

supply to charge the battery (Max wire length is 9.8 ft.

alarm, status, and control messages from SiX series devices, panel. The control then responds accordingly (arm/disarm

supply to charge the battery (Max wire length is 9.8 ft.

To enroll the device, use the programming app. When

Controller’s instructions for details.

To enroll the device, use the programming app. When

Controller’s instructions for details.

To enroll the device, use the programming app. When

Controller’s instructions for details.

Wireless Repeater / Wireless Repeater/Wireless Repeater

The SiXREPEATER is an RF receiver and a transmitter and is intended to extend the range of Honeywell’s SiX series devices by 200 feet (nominal). The SiXREPEATER receives alarm, status, and control messages from SiX series devices, and forwards these messages to control

the system, initiate an alarm, etc.

FEATURES

• Transmits its own status, including tamper, AC loss, and RF Jam.

• Status sent when change occurs or during the one hour supervisory check in.

• Provides a 24-hour backup rechargeable battery.

• Features a Spatial Diversity system that virtually

eliminates the possibility of "Nulls" and "Dead Spots" within the coverage area.

• Front and wall tampers

GENERAL GUIDELINES

• The SiXREPEATER module uses a 5VDC power (3m)).

• If the voltage drops to 3.6VDC a low battery will occur.

NOTE: Anything lower than 2.6VDC, it is incapable

of charging the battery; it must be replaced

• Before mounting permanently, conduct the Go/No Go test (see controller’s instructions) to verify adequate signal strength, relocate if necessary.

• The SIXREPEATER can be installed in a residential environment and is designed to operate 200 plus feet through 3 walls of wood, aluminum and dry wall construction.

• The SiXREPEATER is designed for a single repeat, meaning the correct path is transmitter > repeater > receiver. NOT transmitter > repeater > repeater > receiver.

The SiXREPEATER is an RF receiver and a transmitter and is intended to extend the range of Honeywell’s SiX series devices by 200 feet (nominal). The SiXREPEATER receives

and forwards these messages to control panel. The control then responds accordingly (arm/disarm the system, initiate an alarm, etc.

FEATURES

• Transmits its own status, including tamper, AC loss, and RF Jam.

• Status sent when change occurs or during the one hour supervisory check in.

• Provides a 24-hour backup rechargeable battery.

• Features a Spatial Diversity system that virtually

eliminates the possibility of "Nulls" and "Dead Spots" within the coverage area.

• Front and wall tampers

GENERAL GUIDELINES

• The SiXREPEATER module uses a 5VDC power supply

to charge the battery (Max wire length is 9.8 ft. (3m)).

• If the voltage drops to 3.6VDC a low battery will occur.

NOTE: Anything lower than 2.6VDC, it is incapable of

charging the battery; it must be replaced

• Before mounting permanently, conduct the Go/No Go

test (see controller’s instructions) to verify adequate signal strength, relocate if necessary.

• The SIXREPEATER can be installed in a residential

environment and is designed to operate 200 plus feet through 3 walls of wood, aluminum and dry wall construction.

• The SiXREPEATER is designed for a single repeat,

meaning the correct path is transmitter > repeater > receiver. NOT transmitter > repeater > repeater > receiver.

the system, initiate an alarm, etc.

FEATURES

• Transmits its own status, including tamper, AC loss, and RF Jam.

• Status sent when change occurs or during the one hour supervisory check in.

• Provides a 24-hour backup rechargeable battery.

• Features a Spatial Diversity system that virtually

eliminates the possibility of "Nulls" and "Dead Spots" within the coverage area.

• Front and wall tampers

GENERAL GUIDELINES

• The SiXREPEATER module uses a 5VDC power

(3m)).

• If the voltage drops to 3.6VDC a low battery will

occur. NOTE: Anything lower than 2.6VDC, it is incapable

of charging the battery; it must be replaced

• Before mounting permanently, conduct the Go/No Go

test (see controller’s instructions) to verify adequate signal strength, relocate if necessary.

• The SIXREPEATER can be installed in a residential

environment and is designed to operate 200 plus feet through 3 walls of wood, aluminum and dry wall construction.

• The SiXREPEATER is designed for a single repeat,

meaning the correct path is transmitter > repeater > receiver. NOT transmitter > repeater > repeater > receiver.

PLACEMENT

Find the “Null” or “Dead Spot”

1. Enter the Walk test mode.

2. Activate any enrolled SiX transmitter in your hand. Listen for the panel to beep and acknowledge the fault.

3. With the enrolled transmitter in your hand continue to fault/restore it until the panel stops acknowledging it.

4. Mount the SiXREPEATER in this location following the guidelines below.

MOUNTING

NOTE: for best results mount the SiXREPEATER as high

as possible, keeping it away from metal objects.

1. Select a mounting position for the module. In most

installations, the best mounting location is close to the existing control panel.

NOTES:

• If needed, you may cut and splice (observing good workmanship) the battery wires and extend their length up to 3 ft. (0.9 meters) using 22 AWG wire, minimum.

• DO NOT mount on or inside a metal enclosure/object.

2. Attach to the wall using the supplied screws.

3. Install the center screw to secure the back tamper to

the wall.

4. Ensure the wiring is complete. Use cable ties as

necessary to secure wiring.

5. Plug the power supply into an un-switched outlet and

secure with screw.

6. Attach the backup battery wires.

PLACEMENT

Find the “Null” or “Dead Spot”

1. Enter the Walk test mode.

2. Activate any enrolled SiX transmitter in your hand. Listen for the panel to beep and acknowledge the fault.

3. With the enrolled transmitter in your hand continue to fault/restore it until the panel stops acknowledging it.

4. Mount the SiXREPEATER in this location following the guidelines below.

MOUNTING

NOTE: for best results mount the SiXREPEATER as high as

possible, keeping it away from metal objects.

1. Select a mounting position for the module. In most

installations, the best mounting location is close to the existing control panel.

NOTES:

• If needed, you may cut and splice (observing good workmanship) the battery wires and extend their length up to 3 ft. (0.9 meters) using 22 AWG wire, minimum.

• DO NOT mount on or inside a metal enclosure/object.

2. Attach to the wall using the supplied screws.

3. Install the center screw to secure the back tamper to the

wall.

4. Ensure the wiring is complete. Use cable ties as

necessary to secure wiring.

5. Plug the power supply into an un-switched outlet and

secure with screw.

6. Attach the backup battery wires.

PLACEMENT

Find the “Null” or “Dead Spot”

1. Enter the Walk test mode.

2. Activate any enrolled SiX transmitter in your hand. Listen for the panel to beep and acknowledge the fault.

3. With the enrolled transmitter in your hand continue to fault/restore it until the panel stops acknowledging it.

4. Mount the SiXREPEATER in this location following the guidelines below.

MOUNTING

NOTE: for best results mount the SiXREPEATER as high

as possible, keeping it away from metal objects.

1. Select a mounting position for the module. In most

installations, the best mounting location is close to the existing control panel.

NOTES:

• If needed, you may cut and splice (observing good workmanship) the battery wires and extend their length up to 3 ft. (0.9 meters) using 22 AWG wire, minimum.

• DO NOT mount on or inside a metal enclosure/object.

2. Attach to the wall using the supplied screws.

3. Install the center screw to secure the back tamper to

the wall.

4. Ensure the wiring is complete. Use cable ties as

necessary to secure wiring.

5. Plug the power supply into an un-switched outlet and

secure with screw.

6. Attach the backup battery wires.

ENROLLING ENROLLING ENROLLING

prompted for MAC ID, activate the device by powering up or, if already powered, press the tamper switch. NOTE: Once enrolled in a system, the SiXREPEATER

cannot be used with another controller until it is removed from the current controller. See the

prompted for MAC ID, activate the device by powering up or, if already powered, press the tamper switch. NOTE: Once enrolled in a system, the SiXREPEATER

cannot be used with another controller until it is removed from the current controller. See the

prompted for MAC ID, activate the device by powering up or, if already powered, press the tamper switch. NOTE: Once enrolled in a system, the SiXREPEATER

cannot be used with another controller until it is removed from the current controller. See the

24-HOUR ENROLLMENT DELETION AND

24-HOUR ENROLLMENT DELETION AND DEFAULT

SUPERVISION

RSSI

Power

RF Jamming

Green /

Green

Reliable Signal

AC Powered /

AC Powered

OK, No Jamming /

OK, No Jamming

Yellow /

Yellow

Marginal Signal /

Marginal Signal

Operating on Battery /

Operating on Battery

Jam Detected /

Jam Detected

Red /

Red

No Signal /

No Signal

Low Battery /

Low Battery

Can’t avoid Jamming /

Can’t avoid Jamming

installed.

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS

DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

DECLARACIÓN IFETEL

For Technical Support,

Pour le support technique,

ASAP).

Para Soporte Técnico,

ASAP).

U.S. warranty / U.S. garantie

Patents / Brevets/Patentes

FEDERAL COMMUNICATIONS COMMISSION (FCC) & ISED

Responsible Party / Issuer of Supplier’s

NY 11747, Ph: 516-577-2000

Partie responsable / Émetteur de la déclaration de

516 577-2000

Voltage / Voltage / Voltage

Acceptable Cable Size ....................................... 14 – 22AWG

DEFAULT

If the device is enrolled in a panel di fferent than the intended panel, and you are unable to delete it from the unintended panel, reset default the device to factory default sett i ng:

1. Open t he cover and verify device is powered on.

2. P res s and hold the tamper switch for 20 s econds.

3. The Green enrol l ment LED rapidly flashes and the

SiXREPEATER defaults.

This procedure is available for 24 hours af ter enrollment with a panel and the device remains powered (battery installed).

If module supervision i s desired, assign the SiXREPEATER to a zone. This sends check -in, low battery, AC loss, and RF jam messages. When prompted, toggle the tamper switch to enroll the MAC ID number. The yellow LED should bli nk on when messages are sent.

Program the zone configuration as follows:

Zone Type Input Type Loop

8 (24-hour aux) 3 (supervised RF) 1

NOTES:

• The SiXREPEATER reports AC loss and RF jam conditions as “low battery” stat us, which is also displayed on the control’s k eypads . This prevents either condition from causing an alarm when the control is armed.

• The SiXREPEATER will not repeat a message that has already been repeated.

• If an actual low battery conditi on i s reported, it takes up to 12 hours after AC power is restored for t he l ow battery restore message to be sent (requires 12 hours for fully recharged battery).

If the device is enrolled in a panel di fferent than the intended panel, and you are unable to delete it from the uni ntended panel, reset default the device to fac tory default setting:

1. Open t he cover and verify device is powered on.

2. P res s and hold the tamper switch for 20 s econds.

3. The Green enrol l ment LED rapidly flashes and the

SiXREPEATER defaults.

This procedure is available for 24 hours af ter enrollment with a panel and the device remains powered (battery installed).

Program the zone configuration as follows:

Zone Type Input Type Loop

8 (24-hour aux) 3 (supervised RF) 1

NOTES:

• The SiXREPEATER reports AC loss and RF jam

conditions as “low battery” stat us, which is also displayed on the control’s keypads. T hi s prevents either condition from causing an alarm when the c ont rol i s armed.

• The SiXREPEATER will not repeat a message that has

already been repeated.

• If an actual low battery conditi on i s reported, it takes up to

12 hours after AC power is restored for the low battery restore message to be s ent (requi res 12 hours for fully recharged battery).

If the device is enrolled in a panel di fferent than the intended panel, and you are unable to delete it from the uni ntended panel, reset default the device to fac tory default setting:

1. Open the cover and verify device is powered on.

2. Press and hold the tamper switch f or 20 seconds.

3. The Green enrollment LED rapidly flashes and the

SiXREPEATER defaults.

This procedure is available for 24 hours af ter enrollment with a panel and the device remains powered (battery installed).

Program the zone configuration as follows:

Zone Type Input Type Loop

8 (24-hour aux) 3 (supervised RF) 1

NOTES:

• The SiXREPEATER reports AC loss and RF jam

conditions as “low battery” stat us, which is also displayed on the control’s keypads. T hi s prevents either condition from causing an alarm when the c ont rol i s armed.

• The SiXREPEATER will not repeat a message that has

already been repeated.

• If an actual low battery conditi on i s reported, it takes up to

12 hours after AC power is restored for the low battery restore message to be s ent (requi res 12 hours for fully recharged battery).

TAMPER/LOW BATTERY REPORTING TAMPER/LOW BATTERY REPORTING TAMPER/LOW BATTERY REPORTING

The SiXREPEATER reports this condition to the control. If a low battery or tamper condition exist s all zones used on the module shows a trouble on the control.

IMPORTANT:

The first battery test occurs 1-hour after power up. To quickly verify a good backup battery, unpl ug and then plug back in the power supply; the system will perform a battery test within 1-minute.

LED INDICATIONS / LED INDICATIONS / LED INDICATIONS

The SiXREPEATER reports this condition to the control. If a low battery or tamper condition exist s all zones used on the module shows a trouble on the control.

IMPORTANT:

The first battery test occurs 1-hour after power up. To quickly verify a good backup battery, unpl ug and then plug back in the power supply; the system will perform a battery test within 1-minute.

BATTERY / BATTERY / B ATTERY

The SiXREPEATER reports this condition to the control. If a low battery or tamper condition exist s all zones used on the module shows a trouble on the control.

IMPORTANT:

The first battery test occurs 1-hour after power up. To quickly verify a good backup battery, unpl ug and then plug back in the power supply; the system will perform a battery test within 1-minute.

Green /

Yellow /

Red /

Approval Listings / Approbations Homologations / Approval Listings:

FCC / IC - ETL Listed to UL268 & 521 cETL Listed to ULC S530 & S531 Other Standards / Autres normes: RoHS

Reliable Signal

Marginal Signal /

No Signal /

AC Powered /

Operating on Battery /

Low Battery /

OK, No Jamming /

Jam Detected /

Can’t avoid Jamming /

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.

FCC / ISED STATEMENT

This device complies with Part 15 of the FCC Rules, and ISED’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’ISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.

Declaration of Conformity: Honeywell International, 2 Corporate Center Drive., Melville,

conformité du fournisseur : Honeywell International, 2 Corporate Center Drive., Melville, NY 11747, Tél.

SPECIFICATIONS / SPÉCIFICATIONS / SPECIFICATIONS:

Transformer / Transformer / Transformer ............ 300-10259

Input Voltage / Input Vol tage / Input Voltage........ 100 ~ 240VAC, 50 ~60 Hz

Operating Voltage / Operating Vol t age /

Operating Voltage................................................ 5VDC (1A)

Maximum Transformer Dis t ance / Maximum Transform er Di stance /

Maximum Transformer Dis t ance .......................... 9.8ft. (3m)

Battery/ Pile / Bateria ........................................... P/N 300-10342

Environmental / Environmental / Environmental Operating Temperature / Operati ng T emperature /

Operating Temperature ....................................... 14

NOTE: Charging the l i thium battery stops when tem perature is below 32

the lithium battery s t ops when temperature is below 32

battery stops when temperature is bel ow 32

Relative Humidity /Relati ve Humidity /

Relative Humidity ................................................ 95%, Non-condensing / 95%

max. sans condensation

Physical / Physical / Physical

Dimensions / Dimensions / Dimensi ons ............. Length / Length / Length 6.9 in (175 mm) x

Width / Width / Width 4.4 in (113 mm) x Depth / Depth / Depth 1.2 in (31 mm) Conduit Insert / Conduit Insert

Conduit Insert ..................................................... 1/2 in (12.7mm)

Acceptable Cable Size / Acceptable Cable Size /



F (-10C) to 140F (60C)



F (0C)



F (0C) / Charging the lithium

F (0C) / Charging

CAUTION!

The batteries used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 212°F (100°C) or dispose of in fire. Use Panasonic CR123A or DURACELL DL123, DL 123A Lithium batteries. Use of other batteries may present a risk of fire or explosion. Keep used batteries away from children. Dispose of used batteries properly. Remove old batteries. Wait 10 seconds and then replace with four new batteries. To avoid a low battery indication when installing new batteries, both batteries must be installed within 15 seconds of installing the first one. Any low battery condition that may have occurred should clear when the back plate is installed.

MISE EN GARDE!

Les piles utilisées dans ce dispositif peuvent présenter des risques d'incendie ou de brûlure chimique si elles sont mal traitées. Ne rechargez pas, ne désassemblez pas, ne faites pas chauffer et ne jetez pas au feu les piles à plus de 100 °C (212 °F). Utilisez des piles au lithium Panasonic CR123A ou DURACELL DL123, DL 123A. L'utilisation d'autres types de piles peut présenter des risques de feu ou d'explosion. Gardez les vieilles piles hors de la portée des enfants. Débarrassez-vous des batteries utilisées de façon appropriée. Retirez les vieilles piles. Attendez 10 secondes et remplacer-les par quatre nouvelles piles. Pour éviter une indication de piles faibles lorsque vous installez de nouvelles piles, les dos (2) piles doivent être installées en deçà de 15 secondes après l'installation de la première. Toute condition de pilles faibles qui aurait pu se produire devrait être rétablie une fois la plaque arrière installée.

CAUTION!

DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. POUR LES LIMITES DU SYSTÈME D’ALARME AU COMPLET, REPORTEZ-VOUS AU GUIDE D’INSTALLATION DU PANNEAU DE COMMANDE

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS

La operación de este equipo está sujeta a las siguientes dos condiciones

1. Es posible que este equipo o dispositivo no cause interferencia perjudicial y

2. Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.

call 1-877-748-7628, option 3

For documentation, call Customer

Service at:

1-800-238-2727 (1-800-ADT-

ASAP).

appelez 1-877-748-7628,

option 3.

Pour la documentation,

appelez le service clientèle au

1-800-238-2727 (1-800-ADT-

llame al 1-877-748-7628,

Para documentación, llame a

Servicio al Cliente a:

1-800-238-2727 (1-800-ADT-

opción 3

ADT Security Services

1501 Yamato Rd

Boca Raton, FL 33431

www.honeywell.com/security/hsc/resources/wa

www.honeywell.com/patents

Ê800-24400-1bŠ

800-24400-1 8/18 Rev A