Ademco 8DL6CO User Manual

This device is intended for use with Honeywell control
This device is intended for use with Honeywell
SiXCO

Wireless Carbon Monoxide (CO) Detector/ Wireless Carbon Monoxide (CO) Detector

Installation Instructions Instructions d’installation
panels that support SiX series devices. Before installing detectors, please thoroughly read these installation instructions.
control panels that support SiX series devices. Before installing detectors, please thoroughly read these installation instructions.
Features Features
10-year life
CO Detector End-of-Life reporting (detector needs
replacing)
Carbon Monoxide detector maintenance reporting
Low Battery Detection
Multi-color status LED
10-year life
CO Detector End-of-Life reporting
Carbon Monoxide detector maintenance reporting
Low Battery Detection
Multi-color status LED
POWER UP
Remove battery pull tab. Be sure
batteries are seated properly to avoid a low battery condition after 15 seconds.
Upon power up, Green LED
Blinks every 2 secs / Sounder is Silent.
POWER UP
Remove battery pull tab. Be
sure batteries are seated properly to avoid a low battery condition after 15 seconds.
Upon power up, Green LED
Blinks every 2 secs / Sounder is Silent.
ENROLLMENT ENRÔLEMENT
This device can be enrolled and programmed either before or after installation.
1. Set the Lyric Controller in Programming Mode and go to
Zone Programming. Select Add New and then Serial Number.
2. Remove the battery tabs to activate the device and begin
the enrollment process.
3. The Green LED flashes rapidly during enrollment (up to
about 20 seconds).
*NOTE: Enrollment time varies depending on the signal
strength between the device and the controller.
The detector sends its unique MAC ID (Serial Number)
and Services information to the controller.
The controller registers the device and displays the
transmitter data on screen.
4. Enrollment is confirmed when the Green LED is ON for 3
seconds and the detector chirps.
5. Press SAVE.
Le dispositif peut être enrôlé et programmé avant ou après l'installation.
1. Réglez le contrôleur Lyric en mode de
programmation et accédez à la programmation des zones. Sélectionnez Add New (ajouter nouveau) et ensuite Serial Number (numéro de série).
2. Retirez la languette qui recouvre la pile pour
activer le dispositif et commencer la procédure d'enrôlement.
3. La DEL verte clignote durant l'enrôlement
(pendant jusqu'à environ 20 secondes*). NOTE: La durée de l'enrôlement varie selon la
puissance du signal entre le dispositif et le contrôleur.
Le dispositif transmet au contrôleur son ID
MAC (numéro de série) et l'information pour les services.
Le contrôleur enregistre le dispositif et affiche
les données du transmetteur sur l'écran.
6.
If the detector is not successfully enrolled during the
4. L'enrôlement est confirmé lorsque la DEL verte est
This procedure is available for 24 hours after enrollment
This procedure is available for 24 hours after enrollment
enrollment period, the LED turns off and the device powers down. Pressing and holding the test button, while powering the detector, will arm the detector to perform a reset to factory defaults.
The device can also be manually enrolled. See the Controller’s Programming Guide for details.
allumée durant 3 secondes et que le dispositif émet un pépiement .
5. Appuyez sur GARDER (Enregistrer).
6. Si le dispositif n'est pas enrôlé avec succès durant la
période d'enrôlement, la DEL s'éteint et le dispositif se met hors tension. Pressing and holding the test
button, while powering the detector, will arm the detector to perform a reset to factory defaults.
Le dispositif peut également être enrôlé manuellement. Pour les détails, reportez-vous au Guide de programmation du contrôleur.
24-Hour Enrollment Deletion and Default
If the device is enrolled in a panel different than the intended panel, and you are unable to delete it from the unintended panel, reset default the device to factory default setting:
with a panel and the device remains powered (battery installed).
Remove power from the detector. Press the CO Test Button. While holding the test button, insert the batteries. Continue holding the test button for 10 seconds and release. The status LED should start blinking green rapidly to confirm its deleted enrollment.
If the device is enrolled in a panel different than the intended panel, and you are unable to delete it from the unintended panel, reset default the device to factory default setting:
with a panel and the device remains powered (battery installed).
Remove power from the detector. Press the CO Test Button. While holding the test button, insert the batteries. Continue holding the test button for 10 seconds and release. The status LED should start blinking green rapidly to confirm its deleted enrollment.
2
MOUNTING
MONTAGE
After enrolling and before mounting permanently,
conduct Go/No Go test (see controller’s instructions) to
After enrolling and before mounting permanently,
verify adequate signal strength. Adjust the device location as necessary.
1. Remove the CO with a counter-clockwise motion.
2. Using two supplied screws and anchors, mount the
base.
3. Attach the CO detector to the mounting base with a
clockwise motion.
4. Test each detector as described in the Testing section.
5. Confirm all desired signals have been received by the
Central Station.
conduct Go/No Go test (see controller’s instructions) to verify adequate signal strength. Adjust the device location as necessary.
1. Remove the CO with a counter-clockwise motion.
2. Using two supplied screws and anchors, mount the
base.
3. Attach the CO detector to the mounting base with a
clockwise motion.
4. Test each detector as described in the Testing section.
5. Confirm all desired signals have been received by the
Central Station.
NOTE: NFPA 72 recommends the installation of detectors only
after completing construction or any other dust producing activity.
Ceiling Mount / Ceiling Mount
NOTE:
NFPA 72 recommends the installation of detectors only after completing construction or any other dust producing activity.
Wall Mount / Wall Mount
3
TESTING
Test communications between the detector and the
TESTING
While the green LED is blinking once per second, spray
The CO test will automatically clear when the CO clears
6. Reattach the cover to the detector.
6. Reattach the cover to the detector.
control panel. The detector has one test button (for testing CO).
The detector may also be functionally tested using canned CO. If the detector fails the test method, the detector should be replaced.
Test communications between the detector and the control panel. The detector mode has one test button (for testing CO)
The detector may also be functionally tested using canned CO. If the detector fails the test method, the detector should be replaced.
NOTE: Testing the detector will activate the alarm and send a signal to the panel.
Before testing, notify the proper authorities to avoid any false alarms.
CO Test (Alarm Test)
Press and hold the CO Test button for 1 to 2 seconds. The control panel should display and sound a CO alarm (all programmed CO detector loops are sent).
NOTE: Testing the detector will activate the alarm and send a signal to the panel.
Before testing, notify the proper authorities to avoid any false alarms.
CO Test (Alarm Test)
Press and hold the CO Test button for 1 to 2 seconds. The control panel should display and sound a CO alarm (all programmed CO detector loops are sent).
CO System Test (Functional CO Test)
Press and hold the CO Test button for 3-5 seconds to enter the functional gas test mode. See Functional Gas Test section below.
Functional Gas Test
Solo C6 brand canned CO may be used to verify the detector’s ability to sense CO by utilizing the RealTest® feature as follows:
1. Remove cover by rotating counter clockwise.
2. Press and hold the CO test button for 3 to 5 seconds.
The green LED will start blinking once per second indicating the detector is in RealTest® mode. (If the detector will not go into RealTest® mode, the CO sensor may be in fault or at end-of- life.)
3.
a small amount of canned CO directly into the CO gas entry port.
4. Upon successful gas entry and if functioning properly,
the detector will go into CO alarm and send an alarm to the control panel.
5.
from the sensor or in 30 seconds if no CO was introduced.
CO System Test (Functional CO Test)
Press and hold the CO Test button for 3-5 seconds to enter the functional gas test mode. See Functional Gas Test section below.
Functional Gas Test
Solo C6 brand canned CO may be used to verify the detector’s ability to sense CO by utilizing the RealTest® feature as follows:
1. Remove cover by rotating counter clockwise.
2. Press and hold the CO test button for 3 to 5 seconds.
The green LED will start blinking once per second indicating the detector is in RealTest® mode. (If the detector will not go into RealTest® mode, the CO sensor may be in fault or at end-of- life.)
3. While the green LED is blinking once per second,
spray a small amount of canned CO directly into the CO gas entry port.
4. Upon successful gas entry and if functioning
properly, the detector will go into CO alarm and send an alarm to the control panel.
5. The CO test will automatically clear when the CO
clears from the sensor or in 30 seconds if no CO was introduced.
4
Loading...
+ 8 hidden pages