Ademco 8DL6162RF Users Manual
y
y
GO TO PAGE 4
FOR FCC / IC
INFORMATION
ADEMCO 6162RF Keypad / Transceiver – Installation and Setup Guide
Alphanumeric Addressable Keypad/Transceivers for use with Honeywell Control Panels; incorporates functions
of a High RF Receiver and a 5800 Transmitter module.
• Supports wireless key transmitters
(e.g., 5834-4) and bi-directional
transmitters (e.g.; 5804BD,
5828/5828V).
• Supports wireless keys with high-
security (encryption) capability (e.g.;
5834-4).
• Provides a nominal range of 200
feet for RF transmitters (some
transmitters have a shorter range).
• Supports RF jam detection.
Sounder
6162: 4-Line Alpha Display
Custom Zone Designators
= System ARMED
= System NOT ARMED
= READY to Arm
= NOT READY to Arm
Arming Keys
To activate Function keys,
press and hold key for at
least 2 seconds; key pairs
are activated immediately.
Table 1 – Programmable
Function Keys
A or
B or and
C or and
D
Note: See the control's instructions for
details on programming the Function
keys for panic alarms or other special
functions (i.e., macros).
and
1. OPEN
1
2
2. WIRE
• Connect only one wire per terminal.
• For Daisy-Chain Configurations, use
wire splicing so only one wire is
connected to each terminal.
G
To Control Panel
Terminal Strip
Y
6162rf-KEYPAD-LBLD-V0-032713
Programmable Function Keys
Table 2 – Settings Ke
Settings Ke
Press
Displays Settings Menu*:
1 Set Time/Date
2 View Event Log
3 Reboot Keypad
4 Set User Code**
Result
* Follow instructions in the User Guide for these options; selecting
option 3 reboots the 6162 keypad.
** Set User Code option available only with the following Control
Panels: VISTA-10P Rev 4.16, VISTA-15P Rev 9.16, VISTA20P Rev 9.16 and VISTA-21iP Rev 3.16.
Control Panel
Wall
Surface
Table 3 – Icon Descriptions
ICON DESCRIPTION
SETTINGS
ARM AWAY
ARM STAY
ARM NIGHT STAY
DISARM
ARM MAXIMUM
TEST SYSTEM
BYPASS ZONES
ARM INSTANT
ASSIGN CODES
CHIME MODE
Control Panel Terminal Strip
AUX
Black (Gnd)
Red (+12vdc)
Green (Data To Control)
Yellow (Data From Control)
AU X DATAINDATA
OUT
Keypad
Front Cover
Install Four (4)
Mounting Screws
3. MOUNT
• Mount on drywall, or in
a single or double-gang
electrical box.
Optional Front Cover Securing Screw
(Required in European Installations)
6162RF-installation-3-21-13
APPLICATION GUIDELINES FOR THE 6162RF
Table 4 – Application Guidelines
If… And… Then…
This is the only
transceiver on
the system,
You want to use both
the receiver and
transmitter function
on a single-partition
system,
• Set the keypad to a device address assigned to the desired partition.*
• Enable the receiver.
• Program a system House ID in the control panel (this will enable the transmitter
function).**
• Set the wireless devices that will communicate with this 6162RF to the same
system House ID.
There is another
receiver or
transceiver on
the system,
You want to use only
the transmitter
function on a second
partition,
• Set the keypad to a device address assigned to the desired partition.*
• Disable the receiver.
• Program a DIFFERENT House ID in the 6162RF than is programmed in the control
panel.*/ **
• Set the wireless devices that will communicate with this 6162RF to the same
House ID as the 6162RF.
You want to use only
the transmitter
function on a singlepartition system,
• Set the keypad to a device address assigned to the Partition 1.
• Disable the receiver.
• Program a House ID in the 6162RF that matches the system House ID
programmed in the control panel.*
• Set the wireless devices that will communicate with this 6162RF to the same
House ID.
Notes:
* On VISTA-40 panels and above, wireless keypads (e.g., 5828) can only be used on a single partition. This partition is programmed in field 1*48,
and must match the partition assigned to the 6162RF. Wireless keys can be used on more than one partition, using a House ID programmed in the
6162RF and the devices. In this case, the wireless keys must be assigned to the same partition as the 6162RF.
** On VISTA-20P panels, the 6162RF will use the House ID programmed in the panel for the partition to which it is assigned. Wireless keypads can
only be used on Partition 1.
4. PROGRAM
Refer to the following procedure to program the 6162RF:
Table 5 – 6162RF Programming
STEP DESCRIPTION DISPLAY CHOICES
1.
Enter Programming Mode: Within 60 seconds of power up, press and hold down the
same time for 3 seconds.
Keypad Address. The keypad address appears (Default = 16). Enter
2.
a two-digit keypad address. Press the key to continue.
Notes: – Refer to the control panel’s installation instructions for the
Receiver Enable. Enter [1] to enable, or [0] to disable the receiver.
3.
Press to continue.
Receiver Address. If the receiver is enabled, enter the two-digit
4.
receiver address. (00-30).
Note: Refer to the control panel’s installation instructions for the acceptable
Press
User Code. Enter a valid four-digit user code to enable single button
5.
arming keys. The user code must be programmed in the control.
Press
acceptable keypad addresses.
receiver addresses.
to continue.
to continue.
CON ADDR = 16
RECEIVER
ON [0= OFF]
REC ADDR = 00
USER CODE : ****
and keys at the
00-31
1 = ON
0 = OFF
00-30
0000-9999
- 2 -
Loading...