Ademco 8DL6160RF 2 Users Manual

K0903V1 2/06 Rev. E

FCC / IC AGENCY
STATEMENTS ARE
ON PAGE 4

ADEMCO 6160RF

ADEMCO 6160RF

Installation and Setup Guide

Installation and Setup Guide

Installation and Setup GuideInstallation and Setup Guide

ADEMCO 6160RFADEMCO 6160RF

Keypad/Transceiver

Keypad/Transceiver

Keypad/TransceiverKeypad/Transceiver

GENERAL INFORMATION

The ADEMCO 6160RF keypad/transceiver is a combination unit that combines the functions of the following
devices:

• 6160 Alphanumeric Addressable Keypad

• 5881H RF Receiver

• 5800TM Transmitter Module

The 6160RF Keypad/Transceiver may be used on any control panel that supports 5800 Series wireless devices
(e.g., VISTA-10P, VISTA-15P, and VISTA-20P).

FEATURES

• Supports wireless key transmitters (e.g.; 5804) and bi-directional transmitters (e.g.; 5804BD, 5828/5828V).

• Supports wireless keys with high-security (encryption) capability (e.g.; 5804E, 5834-4).

• Provides a nominal range of 200 feet for RF transmitters (some transmitters have a shorter range).

• Supports RF jam detection when the receiver is enabled.

• Capable of sending status signals (Armed, Ready, etc.) to bi-directional units such as 5804BD, 5804BDV and

5828/5828V.

UUUU

The following 5800 series transmitters are not intended for use in UL installations: 5802, 5804, 5804BD, 5804BDV, 5804E,

LLLL

5814, 5819, 5819BRS, 5819WHS, and 5828/5828V.

INSTALLING THE 6160RF

Locate the 6160RF in an area and at a height where
it is convenient for user operation. The 6160RF must
be at least 10 ft from the control panel to ensure
proper operation of the RF receiver.

Mounting and Wiring

The 6160RF has terminal blocks for connection to
power and data wires. Removing the keypad’s case
back provides access to the terminal blocks.

The 6160RF can be surface mounted directly to
walls, or to a single- or double-gang electrical box.
Follow these steps to mount and wire the keypad:

1. Push the two case release snaps at the bottom of
the keypad with the blade of a medium
screwdriver (this will push in the release snap),
then pull that side of the case back away. Insert
the screwdriver in the side of the keypad
(between the front and back case) and gently
twist to release the side locking tab. Repeat for
the other side. Refer to Figure 1 for location of the
case back release snaps and locking tabs.

Pass the wiring from the control panel through

2.

the opening in the case back. (see the control
panel’s instructions for proper run lengths.)

a. If surface wiring is being used, wiring may be

routed through the top or the bottom left-side
breakout in the case back. The breakouts must
be punched out using a screwdriver before
mounting the case back.

b. If desired, wires may be strain-relieved to the

wire tie point on the inside of the case back
with a tie wrap (not supplied).

3. Mount the case back to a wall or to an electrical
box using the 25mm-long self-tapping screws
supplied (mollies for drywall are not supplied).

4.

Connect the power and data wires from the
control panel to the terminals on the 6160RF as
indicated in Figure 2 and Table 1.

ARMED

READY

NOTE:

TO REMOVE REAR COVER
PUSH IN THE TWO MOUNTING
SNAPS LOCATED ALONG THE
BOTTOM OF THE KEYPAD
AND LIFT COVER UP.

Figure 1. Removing the Case Back

MOUNTING

RELEASE

SNAPS

LOCKING

TAB

6160RF-003-V1

+

Y

G

+

+++

WIRING TERMINALS

(TO CONTROL PANEL)

Figure 2 - 6160RF Wiring Details

6160RF-002-V1

Table 1 - Wiring Table

Keypad Control Panel Wire Color

G▼ (Data Out)

- -Aux Pwr (GND) Black
+ +Aux Pwr Red

▲Y (Data In)

Data In Green

Data Out Yellow

APPLICATION GUIDELINES FOR THE 6160RF

Use the following guidelines when planning an installation:

If… And… Then…

This is the only
transceiver on
the system,

You want to use both
the receiver and
transmitter function
on a single-partition
system,

• Set the keypad to a device address assigned to the desired partition.*

• Enable the receiver.

• Program a system House ID in the control panel (this will enable the transmitter

function).**

• Set the wireless devices that will communicate with this 6160RF to the same

system House ID.

5. Reattach the keypad to the mounted case back.
Attach the top of the keypad first, and then
press the bottom section down until it snaps
into place securely.

6. Peel off protective film on the LED panel and
install the keypad labels as required.

There is another
receiver or
transceiver on
the system,

You want to use only
the transmitter
function on a second
partition,

• Set the keypad to a device address assigned to the desired partition.*

• Disable the receiver.

• Program a DIFFERENT House ID in the 6160RF than is programmed in the control

panel.*/ **

• Set the wireless devices that will communicate with this 6160RF to the same

House ID as the 6160RF.

You want to use only
the transmitter
function on a single­partition system,

• Set the keypad to a device address assigned to the Partition 1.

• Disable the receiver.

• Program a House ID in the 6160RF that matches the system House ID

programmed in the control panel.*

• Set the wireless devices that will communicate with this 6160RF to the same

House ID.

Notes:

* On VISTA-40 panels and above, wireless keypads (e.g., 5804BD) can only be used on a single partition. This
partition is programmed in field 1*48, and must match the partition assigned to the 6160RF. Wireless keys can
be used on more than one partition, using a House ID programmed in the 6160RF and the devices. In this case,
the wireless keys must be assigned to the same partition as the 6160RF.

** On VISTA-20P panels, the 6160RF will use the House ID programmed in the panel for the partition to which
it is assigned. Wireless keypads can only be used on Partition 1.

PROGRAMMING THE 6160RF

Refer to the following procedure to program the 6160RF:

STEP DESCRIPTION

1. Enter the program mode by pressing the [1] and [3] keys simultaneously
for a few seconds within 60 seconds after applying power.

2. (Keypad Address) Enter the two-digit keypad address. Press the [✻] key
to continue.

Notes: (1) Refer to the control panel’s installation instructions for the

(2) On the VISTA-40 and above the 6160RF’s partition assignment must

3. (Receiver Enable) Enter [1] to enable, or [0] to disable Receiver. Enable
the receiver if RF transmitters or wireless keypads are programmed into
the control and no other receivers are enabled. Press the [✻] key to
continue.

acceptable keypad addresses.

match the RF keypad partition assignment programmed in field
(1*48).

- 2 -

DISPLAY

CON ADDRESS

CON ADDRESS = XX

CON ADDRESS CON ADDRESS

RECEIVER

RECEIVER

RECEIVERRECEIVER
ON [0

ON [0

=

OFF]

ON [0ON [0

OFF]

OFF] OFF]

XX

XX XX

CHOICES

00-31

1= ON
0 = OFF

A

STEP DESCRIPTION DISPLAY CHOICES

4. (Receiver Address) If receiver is enabled, enter the two-digit receiver
address. (00-30).

Note: Refer to the control panel’s installation instructions for the acceptable

receiver addresses.

Press the [✻] key to continue.

5. (House ID) This prompt will only appear if the receiver is disabled. If the
receiver is enabled the 6160RF will use the House ID programmed in
the panel. Refer to Application Guidelines section when selecting a
House ID.

To program a House ID: Enter 01-31.
To disable the transmitter: Enter 00

Note: Each device that will receive status from the 6160RF must be set to the

same House ID as the 6160RF (refer to Application Guidelines section).

Press the [✻] key to continue.

(Enable High Security Mode) Enter [1] to select High Security Mode.

6.

Note: If the High Security mode is enabled, the 6160RF will only recognize

encrypted devices.
commands both encrypted and non-encrypted devices.

Press the [✻] key to continue.

7. (Disable High Security Devices) Press the [✻] key to skip this prompt
and exit Program Mode.

Notes: (1) The [✻✻✻✻] key must be pressed several times in order to save the

(2) If you need to disable encrypted devices, refer to the Disabling High

ACTIVATING HIGH SECURITY DEVICES

This following procedure should be followed if using High-Security (encrypted) devices.

STEP DESCRIPTION

Follow the normal procedure for programming the device into the control panel (refer to the Installation

1.
Instructions for the device that you are programming). Exit out of Programming Mode.

2. Put the control panel in Go/ No Go Test mode. (See the Installation Guide for the panel being installed.)

Follow the instructions supplied with each wireless device to enroll the device in High-security mode. After each

3.
device is enrolled the 6160RF will momentarily display “SECURITY DEVICE” along with the device number and

its serial number.

Note: The 6160RF will support a maximum of 8 devices. If you attempt to enroll additional devices the keypad will display

programmed data.

Security Devices section.

“EXCEEDED NUMBER” “ALLOWED DEVICES”.

If this mode is disabled, the 6160RF will process

REC ADDRESS

REC ADDRESS= XX

REC ADDRESSREC ADDRESS

HOUSE ID

HOUSE ID = XX

HOUSE ID HOUSE ID

HIGH SECURITY

HIGH SECURITY

HIGH SECURITYHIGH SECURITY
OFF [1

OFF [1]]]] = ON

OFF [1OFF [1

DISABLE HS DEV?

DISABLE HS DEV?

DISABLE HS DEV?DISABLE HS DEV?

=

YES

NO [1

NO [1]]]]

NO [1NO [1

YES

YESYES

ON

ONON

XX

XX XX

XX

XXXX

00-30

00-31

1= Enable
0 = Disable

1= YES
0 = NO

DISABLING HIGH SECURITY DEVICES

This mode gives you the ability to disable high security on all wireless keys that have been enrolled in the
6160RF. This is particularly useful if a user loses a wireless key.

Once high-security (encrypted) devices have been disabled, they will only operate if the 6160RF is set to listen to both
encrypted and non-encrypted devices (programming step 6, above). To completely disable the devices, they must be deleted

!

from the control panel.

STEP DESCRIPTION DISPLAY CHOICES

1.

2.

3.

fter the keypad has been powered for at least 60 seconds hold
down the [1] and [3] keys at the same time for 3 seconds. The
current keypad address will be displayed. (You cannot change the
keypad’s address at this point.) Press the [✻] key to continue.

(Delete High Security Devices) Press the [1] key to remove all high­security (encrypted) devices. Press the [✻] key to continue.

If YES was selected in Step 2 the unit will display a confirm
request to delete the stored high security device. Press the [1] key
to accept, followed by the [✻] key to exit the programming mode.

- 3 -

CON ADDRESS

CON ADDRESS=XX

CON ADDRESSCON ADDRESS

DISABLE HS DEV?

DISABLE HS DEV?

DISABLE HS DEV?DISABLE HS DEV?

NO [1

NO [1]]]]=YES

NO [1NO [1

ARE YOU SURE?

ARE YOU SURE?

ARE YOU SURE?ARE YOU SURE?

NO [1]

NO [1]=YES

NO [1]NO [1]

YES

YESYES

YES

YESYES

XX

XXXX

00-31

1= YES

0 = NO

1= YES

0 = NO

TROUBLESHOOTING

The error messages listed in the following table cause the 6160RF to produce a single ding tone. The table
describes the error messages and the corrective actions.

Display Probable Cause Corrective Action

Low Bat (with

Low battery in the wireless device.

zone no.)

Open Ckt No data is being received from the control panel.

Check 100

Check 1xx*

1. The control panel does not see the 6160RF
Receiver, or the Receiver is not functioning.

2. Another device on the keypad terminals is not
communicating to the control panel.

*xx= the device address of the receiver.

SPECIFICATIONS

Physical: 5-3/8” H x 7-3/8” W x 1-1/4” D
(137mm x 187mm x 32mm)

Current: Standby 50mA

Wiring: Refer to Table 1

Range: 200 ft (60.9 m) nominal

Frequency: 345 MHz

Display: 2 x 16 alphanumeric supertwist LCD, backlit

Sounder: Tone Generator Integrated Circuit. (fire alarm is loud pulsing tone;

FOR DETAILS ON THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM, REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE CONTROL PANEL BEING
INSTALLED IN CONJUCTION WITH THIS DEVICE.

FEDERAL COMMUNICATIONS COMMISSION STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes
or modifications could void the user's authority to operate the equipment.

CLASS B DIGITAL DEVICE STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions,
may cause interference to radio and television reception. It has been type tested and found to compl y with the limits for a Class B computing device in accordance
with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• If using an indoor antenna, have a quality outdoor antenna installed.

• Reorient the receiving antenna until interference is reduced or eliminated.

• Move the radio or television receiver away from the receiver/control.

• Move the antenna leads away from any wire runs to the receiver/control.

• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.

• Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

FCC/IC STATEMENT

This device complies with Part 15 of the FCC Rules, and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1)
Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences causant une reception
indésirable.

WARRANTY INFORMATION

For the latest warranty information, please go to:

http://www.security.honeywell.com/hsc/resources/wa

1. Replace the battery if the wireless transmitter has a replaceable battery.

2. Replace the transmitter if the wireless transmitter does not have a

replaceable battery.

Verify that the keypad

1a. Verify that the keypad

▲Y (yellow) wire is connected properly.

▲Y (yellow) and G▼ (green) wires are

connected properly.

1b. Verify that the control’s receiver address is correct.

2. Verify the wiring connections between the control and all other devices.

Backlighting on and
Sounder on 150mA

burglary/audible panic alarm is continuous tone)

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

‡K0903V1?Š

K0903V1 2/06 Rev. E

Copyright © 2011 Honeywell International Inc.

www.honeywell.com/security