Ademco 8DL6152RF Users Manual

PLEASE GO TO PAGE 7 FOR THE AGENCY STATEMENTS

ADEMCO 6152RF Keypad / Transceiver – Installation and Setup Guide

Fixed Addressable Keypad/Transceivers for use with Honeywell Control Panels; incorporates normally-open relay output with the functions of a medium 16 zone RF Receiver and a 5800 Transmitter module.

Programmable to support the following :

- Bi-directional 5828/5828V wireless keypads and wireless

keys (e.g., 5804BDV, 5834-4, etc.)

- Up to eight button-type wireless keys locally (programmed directly into the keypad), without occupying control panel zones

- Up to 16 5800 series wireless zones programmed into any supported control panel

- Wireless keys with high security mode enabled

To activate Function keys, press and hold key for at least 2 seconds; key pairs are activated immediately.

Table 1 – Programmable Function Keys

A or

B or and

C or and

Note: See the control’s instructions for

details on programming the Function keys for panic alarms or other special functions (i.e., macros).

and

1. OPEN

AWAY

BYPASS

STAY

CHECK INSTANT CANCELED

Sounder

6152RF-KEYPAD-LBLD-032613

ALARM FIRE

Table 2 – Settings Ke

Settings Ke

Press for 2 Seconds

Press for 2 Seconds and during the Display Test,

press and hold

for 3 Seconds

and

Control Panel

NO NIGHT AC

TESTPHONE NOT READY CHIME BAT

Programmable Function Keys

Result

Enters Display Test Mode

Reboots the Keypad (the keypad beeps and the ARM and READY LED’s flash for several seconds)

6152RF: Fixed Word Display 2-Digit Zone Identifier

The ‘21’ digits are used for specific trouble indications. Refer to the control panel instructions for details.

= System ARMED

= System NOT ARMED

= READY to Arm

= NOT READY to Arm

Arming Keys

Table 3 – Icon Descriptions

ICON DESCRIPTION

SETTINGS ARM AWAY ARM STAY ARM NIGHT STAY DISARM ARM MAXIMUM

TEST SYSTEM BYPASS ZONES

ARM INSTANT ASSIGN CODES

CHIME MODE

2. WIRE

• Connect only one wire per terminal.

• For Daisy-Chain Configurations, use wire splicing so only one wire is connected to each terminal.

SEE Detail

Keypad Front Cover

Install Four (4) Mounting Screws

Wall Surface

3. MOUNT

Mount on drywall, or in a single or double-gang electrical box.

AUX

Optional Front Cover Securing Screw (Required in European Installations)

DATAINDATA

OUT

CONTROL PANEL TERMINAL STRIP

[G ] DATA OU T [ ] GROUND [+] +12VDC IN [Y] DATA IN

16-24 AWG Only

Green

Black Red Yellow

Detail

KEYPAD

RELAY OUTPUT CONNECTIONS

INSTALLATION AND APPLICATION GUIDELINES

For installation, consider the following:

• Locate the 6152RF in an area and at a height convenient for user operation.

• The 6152RF must be at least 10 feet from the control panel to ensure proper RF receiver operation.

• Local wireless keys (wireless keys programmed directly into the 6152RF) may be used regardless of whether the RF receiver in the 6152RF is enabled or disabled.

• If using bi-directional devices, be sure to enable the transmitter module in the 6152RF (program address 7).

• If transmitters are programmed into the control panel, be sure to enable the receiver (program address 6). (Do not exceed the number of receivers supported by the control panel.)

• If a local wireless key is programmed to arm/disarm or to trigger a relay on the control panel, a user code must be entered into the 6152RF. This user code must also be programmed into the control panel.

• You must set the House ID only if you are using RF keypads and/or bi-directional devices; AND the House ID Source is the 6152RF (Local).

Partition Installation Example

An example of an installation using two 6152RF Keypad / Transceivers with 2-Way Wireless Devices (e.g., 5828V) on two Partitions is shown below:

6152RF

Partition #1

System House ID = 1

5828 or 5804BD

Partition #1

House ID = 1

CONTROL

PANEL

Partition #1 Partition #2

6152RF

Partition #2

Local House ID = 2

5828 or 5804BD

Partition #2

House ID = 2

Table 4 – Partition Installation

Settings 6152RF #1

Keypad:

House ID:

House ID Source:

Receiver Enable:

Transmitter Enable:

Must be assigned to Partition 1 in the control panel

Match Partition 1 House ID in the control panel and House ID in Wireless Device

System

6152RF #2

Must be assigned to Partition 2 in the control panel

Match House ID in Wireless Device

Local

Off

4. PROGRAM

To program the keypad, first enter the Programming Mode, select a programming address and set the programming options. Refer to the tables below and on the following pages for details on entering Programming mode, default values and programming choices for each option.

Table 5 – Programming Mode

Action Result Displa

1. Enter Program Mode

Within 30 seconds of power up or reboot, press and hold down

the and keys at the same time for 3 seconds.

Note: Refer to Table 2 to reboot

the keypad.

2. Enter a Programming Address

(See Program Address column in Table 6)

3. Set programming options

Use the number and navigation keys to set the programming options.

Enters the Program mode at the Start screen and the keypad beeps three (3) times

Screen displays selected programming address

Refer to Choices column in Table 6.

oo, - -

flash

alternately

[If any other numbers or

letters

appear

press

See

Display

column in

Table 6.

- The keypad will not enter programming mode if the panel is armed.

- Press the power up to enter the User mode. This mode allows individual local wireless keys to be enabled and disabled (useful if, e.g., a user accidentally loses a wireless key). Refer to the User Guide for instructions.

- To enter keypad Programming mode after power up period, reboot the keypad (see Table 2 on page 1) and try again after the keypad LED’s stop flashing.

- The keypad automatically exits the Program mode if no keys are pressed for 90 seconds.

- (For example, enter [1] to go to Keypad Address; enter [2] to go to Receiver Address).

- Press to erase the current information and move back.

- Press

beeps twice and the screen returns to Start

and keys 60 seconds or more after

to store the displayed information, the keypad

Notes

- 2 -

Table 6 – Programming Options

After editing any programming address, pressing

Enter Program Address

Enter [1]

Enter [2]

Enter [3]

Enter [4]

Enter [5]

Moves to Address

Description

Display Choices Default Notes

Keypad Address cA 00-31

Receiver Address rA 00-30

House ID

Only needed if RF keypads and/or bi-directional units are used and House ID source is set for Local.

House ID Source hS 1 = System

Wireless Key Editing d- Enter Existing Device

will save the displayed information and return to the Start screen.

hI 00-31 10

1 (System)

0 = Local

Enable keypad address in the Control panel.

The House ID entered here MUST match the House ID programmed in the RF keypad and the bi-directional unit.

System uses the House ID programmed in the control.

Local uses the House ID programmed in the keypad.

Number (1-8)

Enter [6]

Enter [7]

Enter [8]

Receiver Enable

Enable the receiver if RF transmitters or wireless keypads are programmed into the control.

Transmitter Module Enable

Enable if using bi-directional devices.

Wireless Key Auto Enroll

rE 1 = On (Enable)

0 = Off (Disable)

tE 1 = On (Enable)

0 = Off (Disable)

1 (Enable)

If enabled, the number of receivers cannot exceed the control panel capacity.

Enable Transmitter Module in only one keypad if more than one 6152RF is used and the House ID source is ‘System’.

Wireless Key User Code

Wireless Key Loop Function

See Programming Local Wireless Keys

for Address 8 programming details

Wireless Key On-Board Relay Assignment

Enter [9]

Restore Defaults EE 1 = Restores Defaults

Any Other Key = Does Not Restore Defaults

Enter [0]

High Security Mode† En 1 = Enable;

0 Disable

0 = Disable

Enter [A]

User Code u4 Enter 4-Digit User Code

(0000 – 9999)

For VISTA-10P/15P/20P/21IP use Keypad Addresses 16-23; For VISTA-40/50P/128/250 use Keypad Addresses 00-30

For VISTA-10P/15P/20P/21IP use Receiver Address 00; For VISTA-40/50P/128/250 use Receiver Addresses 01-30 and enable the receiver address in

the Control panel.

This user code will be used to enable the single button arming keys. Must be a valid user code programmed in the control.

† When operating the system in High-Security mode, non-encrypted wireless keys will not function.

Upon exiting the Program mode, the 6152RF alternately flashes "Ad," the 2-digit keypad address, and the 2-digit receiver address. If either of these is incorrect, enter Program Mode again and reset the address(es) (see Tables 5 and 6).

- 3 -

+ 5 hidden pages