Ademco 8DL6150RFT3 Users Manual

K4460-1V6 2/06 Rev C

PLEASE GO TO PAGE 8 FOR THE FCC AND IC STATEMENTS.

ADEMCO 6150RF

ADEMCO 6150RFADEMCO 6150RF

Keypad/Transceiver

Keypad/TransceiverKeypad/Transceiver

INSTALLATION AND SETUP GUIDE

GENERA L INFORMATIO N

The 6150RF Keypad/Transceiver is a combi na tion unit incorporating a norm ally-open relay output and the functions of:

• 6150 Fixed Addressable Keypad

• 5881M RF Receiver

• 5800TM Transmitter Module

The 6150RF Keypad/Transceiver may be used on any control panel that supports the 6150 Keypad.

Wireless Features

The 6150RF supports the following:

• 5828/5828V wireless keypads.

• Up to eight wireless keys locally (programmed directly into

6150RF) without occupying any zones supported by the control panel.

• Button-type transmitters (e.g., 5804, 5804BD) for local operation.

• A maximum of 16 transmitters programmed into any 5800

Series-supported control panel .

• Wireless keys with high-security (e.g., 5804E).

The 5802, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5804E, 5814, 5816TEMP, 5819, 5819BRS, 5819WHS, 5828/5828V and 5850

UUUU

LLLL

transmitters are not intended for UL installations.

Programming Fe atures

• Auto Enroll mode for programming wireless keys.

• Provides a method for deleting a serial number and re-enrolling a new one in its place.

• Provides default settings for the wireless key functions.

Additional Features

• Operates the on-board relay in conjunction with the receiver (e.g., to trip a garage door opener).

This feature is not intended for UL installations.

UUUU

LLLL

• Activates relays programmed into the control panel.

• Provides an End User mode to enable/disable local wireless keys (e.g., if a user accidentally loses a wireless key). Refer to the

6150RF User Guide for this procedure.

INSTALLING THE 6150RF

Locate the 6150RF in an area and at a height where it is convenient for user operation. The 6150RF must be at least 10 feet from the control panel to ensure proper operation of the RF r eceiver. Perform the following steps to i nstall the 6150RF.

1. Push the two case release snaps at the bottom of the keypad with the blade of a medium screwdriver (this will push in the release snap), then pull that side of the case back away. Insert the screwdriver in the side of the keypad (between the front and back case) an d gently twist to release the side locking tab. Repeat for the other side. Refer to Figure 1 for location of the case back relea se snap s and lock in g ta bs.

2. Route the wiring from t he control panel through the opening in the cas e back. (See the control panel’s instructions for proper wire run length s.)

3. Mount the case back directly to a wall or electrical gang box.

4. Connect the power and data wires from the control panel to the terminals on the 6150RF as indicated in the wiring table adjacent to Figure 2.

• RF jam d etection when the receiver i s enabled .

• Low-battery indication s for t h e local wireless keys.

• A nominal range of 20 0' for the RF transmitters (some

transmitters have a shorter range).

• Wireless keys for control panels that do not support RF themselves (such as 4110DL).

• Sends status sig n als (Armed, Ready, etc.) to bi-directional units such as 5804BDV and 5828/5828V.

5. Connect the wires for the relay output (if used) to the terminals on the 6 150RF’s PC board.

6. Reattach the keypad to its case back.

Note: Upon power-up or exit of the Program Mode, the 6150RF

alternately flashes "Ad" and the 2-digit keypad address and the 2-digit receiver address on the display. Press any key to display the system status.

ARMED

READY

NOTE:

TO REMOVE CASE BACK PUSH IN THE TWO MOUNTING SNAPS LOCATED ALONG THE BOTTOM OF THE KEYPAD AND LIFT UP.

RETAINING

SNAPS

Figure 1 – Removing the 6150RF Cas e Back

LOCKING

TAB

6150-006-V0

Keypad Control Panel Wire Color

WIRIN G TABLE

▲G Data In Green

−

− Aux Pwr (GND)

Black

+ + Aux Pwr Red

▼Y Data Out Yellow

Note: NO (normally Open) and C (common) are the

connections for the relay output

Figure 2 - 6150RF Wiring C o nnectio ns

6150RF-003-V2

APPLICATION GUIDELINES

Use the following guidelines when planning an installation:

• Local wireless keys (wireless keys programmed directly into the 6150RF) may be used regardless of whether the RF receiver in the 6150RF is enabled or disabled.

• If using bi-directional devices, be sure to enable the transmitter module in the 6150RF.

• If transmitters are programmed into the control panel, be sure to enable the receiver. (Make sure you do not

exceed the number of receivers supported by the control panel.)

• If a local wireless key is programmed to arm/disarm or to trigger a relay on the control panel, a user code must be entered into the 6150RF. This user code must also be programmed into the control panel.

• You must set the House ID only if you are using RF keypads and/or bi-directional devices; AND the House ID Source is the 6150RF (Local).

6150RF Application Guide

The following guide outlines how to program the wireless keys, RF receiver, and the House ID in the 6150RF for your installation.

Are you using

System Control Panel

4110DL, 4110XM, 4140XMP, VISTA-20HWSE

VISTA-10P, VISTA-10SE, VISTA15, VISTA-15P, VIA-30PSE

VISTA-20SE, VISTA-20P

VISTA-40, VISTA-50P, VISTA128B, VISTA-128BP

* Two 6150RFs are needed for this application: one assigned to partition 1 and one assigned to partition 2. ** If using an RF keypad on only one partition, the 6150RF’s partition assignment in panel programming must match the partition. *** If set for Local on a partition control, the 6150RF’s partition assignment must match the one programmed in the BD device.

RF keys beyond

system’s

capacity?

N/A N/A N/A 6150RF OFF Local [0]

NO NO N/A System ON [1] System [1] YES NO N/A 6150RF ON [1] System [1] YES YES N/A 6150RF OFF [0] Local [0]

NO NO NO System ON [1] System [1] YES NO NO 6150RF ON [1] System [1] YES YES NO 6150RF OFF [0] Local [0]

NO YES YES* System OFF [0] Local [0] YES YES YES* 6150RF OFF [0] Local [0]

NO NO NO** System ON [1 ] System [1] YES NO NO** 6150RF ON [1] System [1] YES YES NO** 6150RF OFF [0] Local [0]

NO YES YES System OFF [0] Local [0] YES YES YES 6150RF OFF [0] Local [0]

RF receivers

beyond

system’s

capacity?

RF keypads and/or Bi-directional devices on more than 1 partition?

Program

Wireless Keys

Into

6150RF Programming Options

Receiver

Enable

House ID

Source***

- 2 -

An example of an installation using two 6150RF Keypad/Transceivers with 2-Way Wireless Devices (e.g., 5828V) on Tw o Partitions is shown below:

CONTROL

PANEL

6150RF

150RF

Settings 6150R F #1 6150RF #2

Keypad: Must be assigned to

House ID: Match Partition 1

House ID Source:

Receiver Enable:

Transmitter Enable:

Partition 1 in the control panel

House ID in the control panel and House ID in Wireless Device

System Local

On Off

On On

PROGRAMMING THE 6150RF

The 6150RF is shipped with pr e-programmed default values. Later in these instructions are dia grams showing the wi re less keys' loop s and their d efault functions. Regardless of which wireless key you use (even if it is one not shown), loops 1-4 are defaulted for all eight devices as

Program Address

1 Keypad Address cA 01-31 31 2 Rece iv er A dd re ss rA 00-30 00 3 House ID HI 01-31 10 4 House ID Sourc e hS 1 = System

5 Wirel es s Ke y Ed it i ng d- Enter Existing Device Number 6 Rece iv er E na bl e rE 1 = On 0 = Off 1 Enab l e

7 Transmitter Module Enable tE 1 = On 0 = Off 1 Enab le 8 Wireless Key Auto Enroll d* Enter Serial Number 8 then 2 Wireless Key User C ode u4 Enter 4-Digit User Code 8 then 4 Wireless Key Loop Function Ln Enter Loop Number then Function

8 then 5 Wireless Key On-Board Relay

9 Restore Defaults EE 1 = Restores Defaults

0 High Security Mode✝ En 1 = Enable; 0 = Disable 0 Disa b l e

* The keypad will display the next number that can be enrolled (i.e., “d3”)

Description Display Choices Default

Assignment

Must be assigned to Partition 2 in the control panel

Match House ID in Wireless Device

o- Enter Loop Number then Relay

0 = Local

(See Wireless Key Function Chart)

Action

Any Other Key = Does Not Restore Defaults

shown. These values may be changed to suit the installation.

Entering Program Mode

Press th e [1] and [3] keys simu ltaneously for a few sec onds within 30 seconds after applying power. The keypad beeps three (3) times, and two da shes and two zeroes flash alternately in the upper left -hand corner of the disp lay. If any other numbers or letters flash in the display, press the [✻] key.

Note: The keypad will not enter programming mode if the system

has been armed before the 6150RF was powered up or down.

Pressing the [1] and [3] keys 30 seconds or more after applying power allows you to enter the Use r mo d e . This mode allows you to enable and disable individual local wireless keys (useful if, e.g., a user accidentally loses a wireless key). Refer to the User Guide for instructions.

Programming Operations

Once you have entered the Program mode, you may move to any program address simply by entering the program address number. The 6150RF will automatically exit the Program mode if no keys are pressed for 90 seconds. While in the Program mode:

• Pressing the [✻] ke y store s the in form at ion displ a yed, then moves you to the next prompt, and the keypad beeps twice.

• Pressing the [#] key erases the current in for mation a nd moves you back so you may enter the correct information.

Enter a program address (e.g., press [1] for Keypad Address; [2] for Receiver Address) to set the parameters in the 6150RF.The following chart lists the program addresses, the keypa d display, an d the choices.

1 Sys t em

Loop 2 1 (Dis arm) Loop 3 2 (Arm Away) Loop 4 3 (Arm Stay) Loo p 1 Cl o se for 2 S e con ds

Deleted: ,

✝ When operating the system in High-Security mode, non-encrypted wireless keys will not function.

- 3 -

+ 5 hidden pages