Ademco 8DL5898 User Manual

5898 Wireless DUAL TEC® Motion Sensor - Installation Instructions

FCC and IC statements are at the bottom of page 8

LOCATION / EM

PLACE

ENT / LOCALIZACIÓ

OPEN /

OUVERTURE /  APERTUR



Wide Angle Lens (installed)

Wide Angle Lens (installed) Wide Angle Lens (installed) 

COM

<FR-CA> PIR Sensitivity - HIGH; Pulse Count 1; 

<SP-Amer> PIR Sensitivity - HIGH; Pulse Count 1; 



PONENTS AND SETTINGS /

PIR Sensitivity - HIGH; Pulse Count 1; 

Up to 50 lb (22.6 kg) Animal Immunity

Up to 50 lb (22.6 kg) Animal Immunity

Alarm when < 45o F (7o C) for > 5 minutes

Alarm when < 45o F (7o C) for > 5 minutes Alarm when < 45o F (7o C) for > 5 minutes



60 Hz Fluorescent Light Filter

60 Hz Fluorescent Light Filter 60 Hz Fluorescent Light Filter

Normal Walk Test Mode

Normal Walk Test Mode Normal Walk Test Mode

2.1 - 2.4 m (7 - 8 ft

)

Animal Immune Lens (included)

Animal Immune Lens (included) Animal Immune Lens (included) 

COM

PONENTS AND SETTINGS / CO

PIR Sensitivity - LOW; Pulse Count 2;  Up to 100 lb (45 kg) Animal Immunity

<FR-CA> PIR Sensitivity - LOW; Pulse Count 2;  Up to 100 lb (45 kg) Animal Immunity <SP-Amer> PIR Sensitivity - LOW; Pulse Count 2; 

2 3 41



Up to 100 lb (45 kg) Animal Immunity

Alarm when > 95o F (35o C) for > 5 minutes

Alarm when > 95o F (35o C) for > 5 minutes Alarm when > 95o F (35o C) for > 5 minutes

50 Hz Fluorescent Light Filter

50 Hz Fluorescent Light Filter 50 Hz Fluorescent Light Filter

Microwave Walk Test Mode

Microwave Walk Test Mode Microwave Walk Test Mode

PONENTS AND SETTINGS

ON

2 3 41

CONNECT THE BATTERIES / 

CONNECT THE BATTERIES /  CONNECT THE BATTERIES



PRELIMINARY DRAFT 5/18/09

Range Adjustment

Réglage de la portée hyper

Ajuste del rango de detección

OUNT / INSTALLATION / M

- 1 -

ONTAJE

Rear Tamper Breakaway Tabs - Best if mounted to a stud, solid wood, or with a robust wall anchor.

<FR-CA>Rear Tamper Breakaway Tabs - Best if mounted to a  stud, solid wood, or with a robust wall anchor. <SP-LA>Rear Tamper Breakaway Tabs - Best if mounted to a  stud, solid wood, or with a robust wall anchor. 



5898 Wireless DUAL TEC® Motion Sensor - Installation Instructions English

Power Up

Trouble or Anti-Mask Fast Blinking Red (LED Enabled 

or Disabled)

Condition Indicator LED

Slow Blinking Red (will finish within  60 seconds)

Indicator LEDs

Normal Walk Test 

Red ON for 3 seconds if Alarm Yellow ON for 2 seconds if Microwave  event detected Green ON for 2 seconds if PIR event  detected

Microwave Walk TestRed ON if Microwave is set too high

Green ON if Microwave is set correctly OFF if Microwave is set too low



BEFORE MOUNTING

Before mounting the transmitter permanently, conduct Go/No Go tests (see control panel manual) to verify adequate signal strength and reorient or relocate the sensor if necessary.

For Animal Immunity

• Mount the center of the sensor at 7.5 ft (2.3 m) high.

• Set the sensor to the Lowest or Low sensitivity (see step 6a).

• Install Animal Immune lens (5-532-489-01 - see Lens Change

Instructions on page

• Install the look-down mask (see

• Install the sensor where animals cannot come within 6 ft (1.8 m) of

the sensor by climbing on furniture or other objects.

• Aim the sensor away from stairways, furniture or other objects that can be climbed on by pets.

ENROLLING THE SENSOR

After connecting the battery, the sensor LED will blink once per second for up to 60 seconds (power up), then Normal walk test mode begins. You must “enroll” the sensor’s ID in the system in this walk test mode.

Eliminate activity in front of the sensor. When prompted for the sensor ID number, wave a hand in front of the sensor lens to trigger alarms and send sensor ID information to the panel.

Refer to the control panel’s manual and the programming tool manual for information on registering wireless devices. Program the sensor as an “RF” type unit (supervised RF).

Loop 1

Loop 2

Loop 3

Loop 4

WALK TEST MODES

Normal Walk Test mode: The 10-minute Normal walk test mode is

designed to optimize sensor enrollment. Only alarm signals for the selected sensitivity/loop are sent to the panel (default is low sensitivity / loop 1). Use the flashlight feature described below to toggle the sensitivity / loop setting.

As you walk through the detection pattern, the sensor LED will either light or blink rapidly to indicate each alarm detection:

- LED turns ON for 3 seconds = low sensitivity / loop 1.

- LED blinks rapidly for 3 seconds = high sensitivity / loop 2.

Flashlight feature

• Stand within 4 feet (1.2 m) of the sensor with a flashlight.

• Blink or wave the flashlight beam across the front of the sensor 3 to

5 times. (For best results, use a flashlight with a strong light beam and time the blinks/waves approximately once every ½ second.)

• The sensor LED will flash for 3 seconds to indicate the sensitivity / loop setting has been changed.

• Each time you use the flashlight feature the sensor sensitivity / loop toggles and the walk test timer restarts the walk test for 10 minutes.

To restart a 10 minute Normal walk test mode after it expires, activate the tamper by opening and closing the sensor.

If necessary, adjust the microwave range, pulse count or sensitivity setting. (For LED activation meaning, refer to the LED Indicator table.)

MICROWAVE WALK TEST – 10 MINUTES

1. Set the Microwave Walk Test DIP switch to ON, or toggle it ON and OFF.

2. Set Range Adjustment potentiometer to 25% and replace the cover.

3. Walk through the detection area and observe the LED.

4. If necessary, adjust the potentiometer until desired detection range is obtained. (For LED activation meaning, refer to the LED Indicator table.)

PRELIMINARY DRAFT 5/18/09

X).

Low Sensitivity (Pulse Count 2) /

Animal Immunity [50 lb. (23 kg) / 100 lb. (45 kg)]

High Sensitivity (Pulse Count 1) / No Animal Immunity

Low Temperature Alarm

Fault = < 45° F

(7° C) for > 5 minutes

Restore = > 48° F

(9° C) for > 5 minutes

Tamper

: (only available for 24 hours after power-up.)

High Temperature Alarm

Fault = > 95° F

(35° C) for > 5 minutes

Restore = < 92° F

(33° C) for > 5 minutes

- 2 -

TROUBLESHOOTING

The sensor indicates a trouble condition by blinking the LED once every 5 seconds. If a trouble condition (self test failure) occurs, the RF supervision is suppressed and the panel reports a trouble (“check zone”) after the condition exceeds the panel’s RF transmitter supervision time. (Self Tests: Microwave Supervision, End-to-End PIR self-test and Temperature Compensation.) Solution: Remove and replace the battery. If the trouble does not clear, replace the sensor.

Replace the battery within 7 days after a “low battery” message appears in the system’s display.

SPECIFICATIONS

Range: 50’ x 60’ (15 m x 18 m) [installed] 35’ x 40’ (11 m x 12 m) [included]

Batteries: Four 1.5V AA Lithium Batteries (Use only Energizer L91)

Battery Caution: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 100° C (212° F), or incinerate. Dispose of used batteries promptly. Keep away from children.

Microwave Frequency: 24.125 GHz (K-band) RF Frequency: 345 MHz PIR White Light Immunity: 6,500 Lux typical Fluorescent Light Filter: 50 Hz or 60 Hz, switch selectable Operating Temperature: -20° to 55° C (-4° to 131° F),

5% - 95% relative humidity (non-condensing) Self-Tests:

Microwave supervision; End-to-End PIR self-test; Temperature Compensation

Temperature Compensation: Advanced Dual Slope PIR Fields of View:

Wide Angle Lens (P/N 5-532-439-01)

44 long range zones 12 intermediate zones 6 lower zones 4 look-down zones

Animal Immune Lens (P/N 5-532-489-01)

44 long range zones 36 intermediate zones 18 lower zones 4 look-down zones

Dimensions: Weight: Accessories:

Optional Lens Kits - Long Range Curtain Lens Kit 15 m x 3 m / 50’ x 10’ (P/N DT7000-LRLK) High Security Lens Kit 11 m x 12 m / 35’ x 40’ (P/N DT7000-HSLK) Pet Alley Lens Kit 11 m x 12 m / 35’ x 40’ (P/N DT7000-PALK)

Mounting Brackets – SMB-10 Swivel Mount Bracket (P/N 0-000-110-01) SMB-10C Swivel Mount Ceiling Bracket (P/N 0-000-111-01) Approval Listings: FCC Part 15, Class B verified IC RSS-210, Class B verified C-Tick,

COMPLIANCE NOTES

• Sensor must be tested once per year.

• Sensor must have a clear line-of-sight to protected area.

4.93” x 2.93” x 1.68” (12.5cm x 7.5cm x 4.3cm)

149.0 g (5.26 oz); Packaged: 205.0 g (7.23 oz)

cULus Listed

5898 Wireless DUAL TEC® Motion Sensor - Installation Instructions FR-Canadian



Power Up

Trouble or Anti-Mask Fast Blinking Red (LED Enabled 

or Disabled)

Condition Indicator LED

Slow Blinking Red (will finish within  60 seconds)

Indicator LEDs

Normal Walk Test 

Red ON for 3 seconds if Alarm Yellow ON for 2 seconds if Microwave  event detected Green ON for 2 seconds if PIR event  detected

Microwave Walk TestRed ON if Microwave is set too high

Green ON if Microwave is set correctly OFF if Microwave is set too low



SELECT MOUNTING LOCATION (See

Additional guidelines for animal immunity:

• Mount the center of the sensor at 2.3 m (7.5 feet) high.

• Set the sensor to the Lowest or Low sensitivity (see step 6a).

• Install Animal Immune lens (5-532-489-01 - see Lens Change

Instructions on page 3).

• Install the look-down mask (see Step 6a).

• Install the sensor where animals cannot come within 1.8 m (6 ft) of

the sensor by climbing on furniture or other objects.

• Aim the sensor away from stairways, furniture or other objects that

can be climbed on by pets.

• TEST the installation site to determine the exact level of attainable

animal immunity.

REMOVE THE FRONT HOUSING (SEE

SELECT THE RANGE, SENSITIVITY AND PROTOCOL (SEE

CONNECT THE BATTERIES (SEE

Refer to the control panel’s manual and the programming tool manual for information on registering wireless devices.

Once you enter the sensor serial number into the panel programming, select the desired loop for that zone.

Serial # / LOOP

Serial #1

/ Loop 1

Serial #1

/ Loop2

No Animal Immunity

Low Sensitivity / Animal

Immunity [23 kg (50 lb.) / 45

Low Temperature Trip

Serial #2

/ Loop 1

When temperature drops

below 7° C ± 2° C

(45° F ± 4° F) for 5 minutes

High Temperature Trip

Serial #2

/ Loop 2

When temperature rises

above 35° C ± 2° C

(95° F ± 4° F) for 5 minutes

MOUNT THE SENSOR (SEE E)

NORMAL WALK TEST– 10 MINUTES

Normal walk test mode activates every time the front cover is closed and remains active for 10 minutes. For an additional 10 minutes of walk test time, remove and replace the front cover. In walk test mode, the LED is always enabled.

Walk through the detection area and observe the LED. If necessary, adjust the microwave range, pulse count or sensitivity

setting. (For LED activation meaning, refer to the LED Indicator table.)

MICROWAVE WALK TEST – 10 MINUTES

1. Set the Microwave Walk Test DIP switch to ON, or toggle it ON and OFF.

2. Set Range Adjustment potentiometer to 25% and replace the cover.

3. Walk through the detection area and observe the LED.

4. If necessary, adjust the potentiometer until desired detection range is obtained. (For LED activation meaning, refer to the LED Indicator table.)

PRELIMINARY DRAFT 5/18/09

High Sensitivity

kg (100 lb.)]



)



)

Pulse Count 1

Pulse Count 2

Low Temp Restoral

When temperature

rises + 2° C

(+ 3° F) above low

temperature trip point

Low Temp Restoral

When temperature

crops - 2° C

(- 3° F) below high

temperature trip point

TROUBLESHOOTING



)

RED LED flashing rapidly during normal operation indicates a trouble condition. A microwave, PIR, or temperature compensation fault is present, or a communication error has occured. Supervision errors and low battery conditions are indicated at the panel.

Solution: Momentarily power down the sensor by removing and replacing all the batteries. If the trouble does not clear, replace the sensor.

SPECIFICATIONS

Range: 50’ x 60’ (15 m x 18 m) [installed] 35’ x 40’ (11 m x 12 m) [included]

Batteries: Four 1.5V AA Lithium Batteries (Use only Energizer L91)

Battery Caution: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 100° C (212° F), or incinerate. Dispose of used batteries promptly. Keep away from children.

5% - 95% relative humidity (non-condensing) Self-Tests:

Microwave supervision; End-to-End PIR self-test; Temperature Compensation

Temperature Compensation: Advanced Dual Slope PIR Fields of View:

Wide Angle Lens (P/N 5-532-439-01)

44 long range zones 12 intermediate zones 6 lower zones 4 look-down zones

Animal Immune Lens (P/N 5-532-489-01)

44 long range zones 36 intermediate zones 18 lower zones 4 look-down zones

Dimensions: 4.93” x 2.93” x 1.68” (12.5cm x 7.5cm x 4.3cm) Weight: 149.0 g (5.26 oz); Packaged: 205.0 g (7.23 oz) Accessories:

Mounting Brackets – SMB-10 Swivel Mount Bracket (P/N 0-000-110-01) SMB-10C Swivel Mount Ceiling Bracket (P/N 0-000-111-01)

Approval Listings: FCC IC CE, C-Tick, cULus Listed

COMPLIANCE NOTES

• Sensor must be tested once per year.

• Sensor must have a clear line-of-sight to protected area.

- 3 -

+ 5 hidden pages