Ademco 8DL5831 3 Users Manual

800-09008 5/11 Rev. A
ADEMCO 5802WXT
INSTALLATION AND SETUP GUIDE
The ADEMCO 5802WXT is a wireless transmitter that may be worn around the neck, on a wrist band or as an apparel clip that may also may be mounted to a desk, dresser, etc. (necklace, band, and clip supplied). Pressing the button on the transmitter sends a signal to the control receiver. The 5802WXT is intended for use only with wireless alarm systems that support 5800 Series devices.
The transmitter is supervised, i.e., it automatically sends a message to the control receiver that includes battery status information every 70-90 minutes.
This transmitter can be programmed as any zone type response (e.g., Emergency Panics, Relay Action, etc.).
Battery Replacement
The 5802WXT is powered by a long-life Lithium battery that may be replaced when a low battery is eventually indicated by the control unit.
NOTE: Although water-resistant, please do not immerse in water at a depth below 10cm for more than 1 hour.
Programming the Serial Number
The 5802WXT has a unique identification code (serial number) permanently assigned during manufacture.
You must “enroll” the transmitter’s serial number and loop number during system programming. The 5802WXT may be defined as Input Type “RF” (supervised RF, for an hourly check-in; do not take out of range) or “UR” (Unsupervised RF). Its loop number is “1.” See the control unit’s Installation Instructions for further details regarding programming. When installation is complete, verify operation from desired location(s).
Specifications
Unit Dimensions: 1.5” (3.9mm) Diameter
LED: Lights when unit transmits. Battery: 3-Volt 2032 Lithium
In UL installations: 3V Panasonic CR2032 only
SUPERVISED MINIATURE
TRANSMITTER
SCREWS (4) TYP.
BATTERY
5802WXT-001-V0
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2011 Honeywell International Inc.
INSERT BATTERY UNDER GOLD TAB
AND PRESS DOWN
5802WXT-002-V0
WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND FOR DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
The user shall not make any changes or modifications to the equi pment unless authorized by the Installation Instr uctions or User's Manual. Unauthorized changes or modifications could void the user's authori ty to operate the equipment.
This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Oper ation is subject to the following two conditi ons: (1) This device may not cause harmful interf erence
(2) This device must acc ept any interference receiv ed, including interf erence that
Cet appareil est conform e à la partie 15 des règles de la F CC & de RSS 210 des Industries Canada. Son foncti onnement est soumis aux conditions suiv antes: (1) Cet appareil ne doit pas causer d' interferences nuisi bles. (2) Cet appareil doit accepter toute interferenc e reçue y compris les interferences causant une reception indésirable.
UL US Listings: HOUSEHOLD BURGLARY WARNING SYSTEM CONTROL UNIT ACCESSORY UL Canadian Listings: HOUSEHOLD BURGLARY WARNING SYSTEM CONTROL UNIT ACCESSORY ALSO LISTED FOR USE AS A SIGNAL APPLIANCE, MISCELLANEOUS CERTIFIED FOR CANADA.
FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
may cause undesired operation.
1. Remove 4 screws and lift off cover.
2. Using a small flat-blade screwdriver remove old battery.
3. Insert new battery by placing new battery under the gold tab and then pressing down. Ensure the POS + side of battery is face up after installation.
4. Align cover and attach with 4 screws.
FCC/IC STATEMENT
IC MODEL: 5802WXT
Ê800-090083
800-09008 5/11 Rev. A
800-09009 5/11 Rev. A
ADEMCO 5802WXT-2
SUPERVISED MINIATURE TRANSMITTER
INSTALLATION AND SETUP GUIDE
The ADEMCO 5802WXT-2 is a wireless transmitter that may be worn around the neck, on a wrist band or as an apparel clip that may also may be mounted to a desk, dresser, etc. (necklace, band, and clip supplied). Pressing both buttons on the transmitter at the same time sends a signal to the control receiver. The 5802WXT-2 is intended for use only with wireless alarm systems that support 5800 Series devices.
The transmitter is supervised, i.e., it automatically sends a message to the control receiver that includes battery status information every 70-90 minutes.
This transmitter can be programmed as any zone type response (e.g., Emergency Panic, Relay Action, etc.).
BATTERY REPLACEMENT
The 5802WXT-2 is powered by a long-life Lithium battery that may be replaced when a low battery is eventually indicated by the control unit.
NOTE: Although water-resistant, please do not immerse in water at a depth below 10cm for more than 1 hour.
PROGRAMMING THE SERIAL NUMBER
The 5802WXT-2 has a unique identification code (serial number) permanently assigned during manufacture.
You must “enroll” the transmitter’s serial number and loop number during system programming. The 5802WXT-2 may be defined as Input Type “RF” (supervised RF, do not take out of range) or “UR” (Unsupervised RF). Its loop number is “1.” See the control unit’s Installation Instructions for further details regarding programming. When installation is complete, verify operation from desired location(s).
Specifications
Unit Dimensions: 1.5” (3.9mm) Diameter LED: Lights when unit transmits. Battery: 3-Volt 2032 Lithium
In UL installations: 3V Panasonic CR2032 only
SCREWS (4) TYP.
BATTERY
5802WXT-001-V0
INSERT BATTERY UNDER GOLD TAB AND PRESS DOWN
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL
WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND FOR DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
The user shall not make any changes or modificati ons to the equipment unless authorized by the Installation Instr uctions or User's Manual. Unauthorized changes or modifications could void the user's authori ty to operate the equipment.
This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Oper ation is subject to the following two conditi ons:
(1) This device may not cause harmful interf erence (2) This device must accept any interference received, includi ng interference that
may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnem ent est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferenc es nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences causant une reception indésirable.
UL US Listings: HOUSEHOLD BURGLARY WARNING SYSTEM CONTROL UNIT ACCESSORY UL Canadian Listings: HOUSEHOLD BURGLARY WARNING SYSTEM CONTROL UNIT ACCESSORY ALSO LISTED FOR USE AS A SIGNAL APPLIANCE,
MISCELLANEOUS CERTIFIED FOR CANADA
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2011 Honeywell International Inc.
5802WXT-002-V0
FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
1. Remove 4 screws and lift off cover.
2. Using a small flat-blade screwdriver remove old battery.
3. Insert new battery by placing new battery under the gold tab and then pressing down. Ensure the POS + side of battery is face up after installation.
4. Align cover and attach with 4 screws.
FCC/IC STATEMENT
IC MODEL: 5802WXT-2
.
Ê800-09009<Š
800-09009 5/11 Rev. A
Loading...