Ademco 8DL5819S User Manual

5819S Wireless Shock Sensor and Transmitter – Installation Instructions

DIP SWITCH

SETTING

Do NOT Remove the PC Board from the back case

PRELIMINARY DRAFT II’s – 06/09/15

The 5819S includes an omni-directional, built-in shock sensor, and is designed to protect window and door surroundings. Use this Shock Sensor and Transmitter with alarm systems that support Honeywell 5800 Series wireless devices.

Typical shock protection area: 6 - 8 feet / 3 - 4 foot radius (1.8m – 2.44m / 0.91m – 1.23m radius); The coverage area can vary depending on the mounting surface.

The device supports three unique zones or “loops”:

Loop 1: Normally Open, built-in shock sensor* Loop 2: Normally closed, built in reed switch, used with the included magnet Loop 3: Externally wired, closed-circuit contact loop connected to the Terminal Block

*Note: This device features the option to enable Loop 1 to report both shock and reed switch faults to the panel on a single zone (see Enroll and Program section for details).

Open the Sensor

Enroll and Program

1. Install the battery and ensure all the DIP Switches are OFF (Highest Sensitivity setting).

2. Assign an individual zone number to each loop used* and assign the zones as Input Type = 3 (Supervised RF).

*Note: To set Loop 1 to report both shock and reed switch faults on a single zone, enroll Loop 1 (do not enroll Loop 2), and set DIP Switch 4 ON after enrollment.

3. Activate any of the device loops (see loop descriptions above) to transmit the device serial number to the control.

• For Loop 1, trigger the shock sensor by shaking the

device, or create a shock near the mounted device.

• For Loop 2, move the magnet close to and away from

the reed switch to trigger it.

• For Loop 3, Open and close the contact according to its

instructions.

4. Trigger again to complete enrollment.

The LED will flash rapidly to indicate the device is transmitting to the control.

Alternatively, enter the device serial number manually when prompted for the information.

Install the Battery

BATTERY CAUTION: Risk of fire,

explosion, and burns. Do not recharge, disassemble, heat above 212°F (100°C), or incinerate. Dispose of used batteries properly. Keep away from children.

DIP Switch Settings

After enrollment, test and adjust the device sensitivity until the desired setting is achieved. (Refer to the Test section.)

Most Sensitive (use this setting for

enrollment)

High Sensitivity

Medium Sensitivity

Low Sensitivity

*Set ON - Loop 1 reports both shock

and reed switch faults on a single zone

Set OFF – Loop 1 reports shock

only

Mount the Sensor

After enrolling and before

For the latest documentation and online support information, please go to:

MyWebTech

Warranty

Ê800-19771bŠ

www.honeywell.com/security

mounting permanently, conduct Go/No Go tests (see the control's instructions) to verify adequate signal strength. Reorient or relocate the device if necessary.

The device can be mounted in any direction for shock sensing.

If using the magnet, install it within 1/2” (12.7mm) of the device as shown.

Test

Use a hard tool to carefully simulate shock impacts on or near the area where the device is mounted. The LED lights each time the shock vibrations trip the device. Adjust the device sensitivity as needed for the application.

Specifications

Power: 1 x 3 V , Lithium Battery (included); Panasonic CR123A, Duracell DL123 or DL123A, Honeywell 466

Operating Temperature: 14° to 131° F / -10° to 55° C (Agency Compliance 32° to 120° F / 0° to 49° C) Relative Humidity: Up to 95% (Agency Compliance up to 93%); non-condensing

Dimensions: 3.05” H x 1.54” W x 1” D (77.47mm H x 39.12mm W x 25.4mm D)

Product must be tested at least once each year.

FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.

CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your

information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• If using an indoor antenna, have a quality outdoor antenna installed.

• Reorient the receiving antenna until interference is reduced or eliminated.

• Move the radio or television receiver away from the receiver/control.

• Move the antenna leads away from any wire runs to the receiver/control.

• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.

• Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une reception indésirable.

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

Approval Listings

FCC part 15, Class B verified IC, RSS-210, Class B verified ETL

Support and Warranty

https://mywebtech.honeywell.com/

For the latest warranty information, please go to:

www.honeywell.com/security/hsc/resources/wa

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

P/N 800-19771 06/15 Rev A