Ademco 8DL5819AP User Manual

N7491-5 3/08 Rev. A

5819AP

SHOCK PROCESSOR TRANSMITTER

INSTALLATION AND SETUP GUIDE

DETAIL A

CASE

HOLDING

POSTS

(2)

MAGNETIC ALIGNMENT GUIDE STRIP

SCREW HOLES

CONTACT TERMINALS (INPUT LOOP 3)

RELEASE FOR BRACKET

SLOT FOR WIRE

SWITCH

SW1 (Most Sensitive) 1ms SW2 2ms SW3 5ms SW4 10ms SW5 (Least Sensitive) 20ms

DETAIL B

JUMPER COUNT

Diagram 1: MOUNTING PLATE

GENERAL INFORMATION

The 5819AP Shock Processor Transmitter connects to inertia type shock detectors that are mounted externally to the transmitter case (detector not supplied), and is intended for use only with Honeywell alarm systems that support 5800 Series wireless devices.

The 5819AP has three unique zones. The first is for a wired, normally closed shock sensor loop (TB1), the second is for a closed contact loop using the unit's built-in magnetic reed switch in conjunction with a magnet, and the third is for a wired closed circuit contact loop (TB2).

The 5819AP has a built-in cover tamper switch that activates when the cover is removed.

INSTALLATION

Mounting

For proper orientation of the unit in relation to the mounting plate, loop wiring, DIP switch adjustment, jumper positions, and/or magnet, read all of this section before installing the unit.

The description that follows assumes that the unit will be mounted as shown in the diagrams, with the magnet (if used) located to the left of the unit. The unit can be installed in any direction, as long as the relationship of the unit to its mounting plate and (if used) magnet is maintained.

Although two holes are provided in the unit that would permit mounting directly to a surface (holes "A" in Diagram 2), it is recommended that the mounting plate be used as described below, for ease in removing the unit for servicing should it become necessary.

Before mounting the transmitter permanently, conduct Go/No Go tests (see control's instructions) to verify adequate signal strength and reorient or relocate the transmitter if necessary.

TABLE 1

RESPONSE TIME

J2 J1

J5 J4 J3

TB2 TB1

TABLE 2

J1 (Most Sensitive) 1 J2 2 J3 4 J4 6 J5 (Least Sensitive) 8

DIP SWITCHES

JUMPER PINS

SHOCK SENSOR TERMINALS (INPUT LOOP 1)

1. Remove transmitter's cover by inserting the flat blade of a

2. Disengage the supplied mounting plate from the unit by

3. If a shock processor or wired contact loop is to be used with

4. Install the mounting plate, with its case-holding posts

5. Attach the case back to the mounting plate by sliding the

6. If the unit's REED SW ITCH is to be used, mount a 5799

7. Set response time (from Table 1) using the DIP switches.

8. Set the pulse count jumper (see Table 2). The pulse count

HOLES “A” (2) (SEE TEXT)

ALIGN MAGNET WITH MARKS ON CASE AND GUIDE ON MTG. PLATE

MAGNET

(OBTAIN

SEPARATELY)

MAGNET

12"

MAX

COVER TAMPER SWITCH

LOCKING TAB RELEASE WINDOW

COVER HOLDING HOOKS (2)

Diagram 2: 5819AP (SHOWN WITH COVER REMOVED)

small screwdriver into the pry-off slot nearest to the cover's decorative ribs, and twisting the blade.

inserting the blade of a small screwdriver into the locking tab release window (see Diagram 2) and pressing it against the locking tab (see Diagram 1) while sliding the plate downward along the case back.

concealed wiring, feed the wires through the concealed wiring entry hole at one corner of the plate. For surface wiring entry, a thin "breakout" area is provided in the case wall.

pointing up (in this example), in the location selected.

keyhole slots in the case back down onto the mounting plate's case-holding posts. The locking tab will click as the case back locks in place.

Magnet (obtained separately) adjacent to the alignment marks on the case and the mounting plate's alignment strip (see Diagram 2).

SW1 sets a response time of 1mS. SW5 sets a response time of 20mS. For a response time of 0.5mS, set all DIP switches to OFF (as shown in DETAIL A in Diagram 1 above).

is reset 3-seconds after the first pulse is detected. There is an LED on the PCB that flashes rapidly on transmission.

Note:

Make the device highly sensitive for the purpose of enrolling the shock sensor loop (TB1) into the system (turn SW1 on and put jumper on J1). After the device has been enrolled, adjust settings as described in steps 7 and 8 (above).

COVER PRY-0FF POINT

BATTERY

–

REED SWITCH (LOOP 2)

DIP SWITCHES See Detail “A”

ANTENNA

JUMPER PINS See Detail “B”

LOOP 1 TERMINALS

(See Detail “B”)

LOOP 3 TERMINALS

(See Detail “B”)

SLOT FOR CONCEALED

WIRING ACCESS

5819AP-001-V0

WIRING CONNECTIONS

With the battery still not inserted, connect the shock processor loop (if used) to the unit's loop TB1 terminals (see Detail "B"). The contact loops must use closed circuit devices. TB2 can be used for normally closed contacts.

Note: If the contact loops are not used, no connection is needed

across their terminals.

"ENROLLING" THE TRANSMITTER SERIAL NUMBER

Each 5819AP Shock Processor has its own unique serial number permanently assigned during manufacture. Each input of the transmitter also has a distinct "loop" number that must be input to the control panel during installation. Assign each to an individual zone and designate the Input Type as "RF" (Supervised RF).

The serial number can be input by one of the following methods:

• "Enrolled" by transmitting from the device during zone programming (pressing the tamper switch, shorting any loop, etc.).

• Entered through the keypad at the "Input S/N" or "Transmit Now" prompt during manual zone programming.

• Entered through COMPASS Downloading Software and downloaded to the control.

When programming the 5819AP transmitter's serial number at the control panel, do the following:

1. At the "Input Type" prompt, enter "3" for RF (Supervised RF).

2. When prompted for the loop number, enter the input loop you are using (see Diagram 2). See the control panel's installation instructions for specific programming procedures.

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL W ITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION, AND FOR DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

BATTERY INSTALLATION/REPLACEMENT

1. Remove the transmitter's cover as described in Mounting, Step 1.

2. Observe correct polarity and insert the battery provided into the battery holder (see Diagram 2).

3. Replace the cover, engage the hooks along one edge, and snap shut.

Do not bend the antenna.

Note:

BATTERY CAUTION: Risk of fire, explosion, and burns. Do not

recharge, disassemble, heat above 212°F (100°C), or incinerate. Dispose of used batteries promptly. Keep away from children.

Replace with 3V Lithium battery only: Panasonic CR123A, Duracell DL123A, or ADEMCO 466.

SPECIFICATIONS:

Transmission Frequency: 315 MHz Unit Dimensions:

4.8" H x 1.5" W x 1" D

TO THE INSTALLER

Regular maintenance and inspection (at least annually by the installer) and frequent testing by the user are vital to continuous satisfactory operation of any alarm system. The installer should assume the responsibility of developing and offering a regular maintenance program to the user, as well as acquainting the user with the proper operation and limitations of the alarm system and its component parts. Recommendations must be included for a specific program of frequent testing (at least weekly) to insure the system's operation at all times.

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. “

This device complies with Part 15 of the FCC Rules, and RSS210 of IC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC / IC STATEMENT

ÊN7491

ÊN7491----5PŠ

ÊN7491ÊN7491

5PŠ

5PŠ5PŠ

N7491-5 3/08 Rev. A

2 Corporate Center Drive, Melville, NY 11747

www.cn.security.honeywell.com/