Ademco 8DL5816OD 1 User Manual

SEE THE BOTTOM OF PAGE 2 FOR FCC & IC

5816OD Wireless Outdoor Sensor – Quick Installation Guide

For Online Support visit: http://www.security.honeywell.com/hsc/resources/MyWebTech/

WARRANTY For the latest warranty information go to: http://www.security.honeywell.com/hsc/resources/wa/

General Information and Component Identification

The Honeywell 5816OD Wireless Outdoor Sensor (referred to as the Sensor) brings the convenience of wireless technology to the outdoors. The major features are:

 Weatherized security protection for an outdoor environment.

Great for sheds, barns, garages, pool gates, fences, and rural mailbox (notifications).

 Versatile mounting options on flat and round materials.  Cover and rear tamper detection.  Can be painted to coordinate with mounting surface.  Operating temp: – 40 to +50° C (– 40 to +122° F) at

RH of 100% (rain, snow).

 Maximum Magnet Gap:

Wood: 1.75 inches Metal: 1.25 inches

Installing / Replacing the Batteries

IMPORTANT:

 Always change both batteries. Do not mix weak batteries with

new batteries.

 Use two (2) lithium 1.5VDC AA cells. (For best life, use

Eveready's Energizer Ultimate LITHIUM AA batteries, Honeywell part number 462)

 OBSERVE BATTERY POLARITY.

Battery Replacement:

1. Remove cover screw and swing Sensor

to remove from Sensor

Mounting Plate.

2. Use screwdriver in any pivot point and pry Sealing Cover

off.

Replace batteries.

3. Orient the Sealing Cover

so the screw hole lines up with the

screw hole in the sensor cover, and press to close.

4. Engage Sensor

tabs into mating holes in Sensor Mounting

Plate and swing closed. Secure with cover screw.

Mounting Guidelines

 This device is intended for vertical surfaces (to be mounted at a

sufficient height) where snow, ice and water buildup will not interfere with its operation.

 Mount the Magnet

identified by the side ribs on the Sensor.

 Mount the Sensor

on the moveable surface.

Magnet

 When used on wooden sheds and barns, mount the sensor and

magnet on the inside of the structure.

 Use the Magnet Spacer

if needed to achieve proper alignment with the Sensor

 Use screws suitable for the material being fastened to.

on the magnet sensing side of the Sensor as

on a stationary surface, and mount the

when mounting on metal surfaces; or

SENSOR

COVER SCREW

FENCE

SENSOR

COMPONENT IDENTIFICATION

PRY POINTS

SENSOR MOUNTING PLATE

TERMINAL BLOCK FOR EXTERNAL CONTACT SWITCH

SEALING COVER

FLAT SURFACES

SENSOR MOUNTING PLATE

MOUNTING SCREW (2)

MAGNET

MAGNET SPACER

5816OD-002-V0

GATE

5816OD-001-V0

MOUNTING SCREW (4)

5816OD-003-V0

Curved Surfaces: Suggested mounting hardware such as the strap ties and cable

ties are not supplied.  Mount using self locking stainless steel strap ties.

5816OD-005-V0

Self Locking Stainless Steel Strap Tie

 Alternately you can use extra heavy duty Nylon 6/6 UV and

Temperature Rated cable ties (0.5 inch wide).

 If desired you may use screws in addition to the ties.

FENCE

COVER SCREW

CURVED SURFACES

SENSOR MOUNTING PLATE

MAGNET SPACER

GATE POST

GATE

SENSOR

MAGNET SENSING SLIDE

MAGNET

5816OD-004-V0

ROUTING EXTERNAL WIRING – Optional for use with external closed contact switches, such as the Honeywell N7945-2GY:

Note: Use minimum of 22AWG jacketed cable. The contact switch must be a Form C (SPDT) type.

CLOSED

COMMON

OPEN

TO EXTERNAL CONTACT SWITCH

UL – The wired contact must be less than 3 feet from the transmitter.

1. Strip cable jacket back 4-inches to allow enough slack to remove Sealing Cover

when changing batteries.

2. Pass cable through the access hole in Sensor Mounting Plate Use cable notch on mounting plate to pass jacketed portion of cable through. Then attach the Sensor Mounting Plate

SENSOR

CONNECT WIRES TO TERMINAL BLOCK IN BATTERY CHAMBER

3. Route cable to the external contact switch and fasten at intervals to secure cable.

4. Remove the Sealing Cover

and thread wires through the

rubber wire seal. If installed, REMOVE ANY BATTERIES.

5. Connect wires to terminal block in battery chamber, then INSTALL the batteries.

6. Replace the Sealing Cover

. (Note, orient the cover so the screw hole lines up with the screw hole in the sensor cover, and press to close.)

7. Engage Sensor and swing closed. Secure with cover screw.

tabs into Sensor Mounting Plate mating holes

PAINTING THE SENSOR:

The sensor and magnet may be painted to coordinate its color with the mounting surface. Use only paints that are made for plastic and follow the manufacturer’s direction for preparing the plastic and applying the paint. Observe the required drying and curing times.

DO NOT USE METALLIC PAINT COLORS.

SEALING COVER

Recommended Paints

 Krylon® "Fusion for Plastic"

 Rust-Oleum® "Plastic"

 Dupli-Color® "Vinyl & Fabric Coating"

SENSOR MOUNTING PLATE

Programming the Control Panel

You must program the transmitter's serial number, input type (RF Supervised), response type, and loop # in the control panel. (Either or both loops may be used. Loop # 2 is for the magnet sensing, and Loop # 1 is for the external contact switch.) Refer to the control panel’s instructions for further details. Note: The transmitter's serial number may be found on the carton, and in the Battery Chamber.

This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences causant une reception indésirable.

FEDERAL COMMUNICATIONS COMMISSION STATEMENT

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User’s Manual. Unauthorized changes or modifications could void the user’s authority to operate the equipment.

Ê800-04494UŠ

800-04494 6/10 Rev. A

FCC / IC STATEMENT

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

5816OD-006-V0