Ademco 8DL58111 Users Manual

Installation Instructions

Model 5811 is a single zone Door/Window
Transmitter, compatible with alarm systems
that support 5800 series wireless devices.
5811 has a unique serial number permanently
assigned during manufacture, which must be
entered into the control panel upon
installation. Refer to the panel’s installation
instructions for programming details.

NOTE: During programming of the control
unit, 5811 transmitters should be treated as
“RF” (i.e. supervised RF) Type.

MOUNTING

Choose a mounting location for 5811 where
the device is stationary and the magnet is
mounted to the moving part of the door or
window. To verify adequate signal strength
conduct Go/No Go tests (see control’s
instructions) on 5811 before mounting
permanently.

1. Install Battery by inserting one edge
under one of the two plastic battery
retainer clips, then pressing down firmly
to snap it beneath both clips; see
diagram.

REED

SWITCH

BATTERY

(+ SIDE UP)

BATTERY
RETAINER
CLIPS

800-03928V1 8/11 Rev. A

ADEMCO 5811

One Zone Door/Window Transmitter

LATCH

E

S

O

L

C

O

T

REED

E

T

A

T

O

R

MAGNET

MAX GAP

3/4"

CASE

TABS

MOUNTING

HOLES

3. Engage the case tabs (see diagram), then
rotate the housing to close. Engage latch
with firm pressure to close and lock.

BATTERY REMOVAL

1. Open housing by inserting a flat blade
screwdriver into latch and twisting gently.

2. Remove old battery cell using a small flat
screwdriver blade, as shown in the
diagram.

SCREWDRIVER

(NO)

SCREWDRIVER

(NO)

X

5811-003-V2

MAGNET

ALIGNMENT

MARKS

A

INSERT BATTERY
EDGE UNDER ONE CLIP

B

PRESS DOWN FIRMLY TO
SNAP BATTERY UNDER

2. Mount 5811 using double-faced tape

BOTH CLIPS

(supplied) by affixing it to the back of the
unit and mounting the unit in place. Use
screws (optional) if desired; see diagram.
Mount the magnet (supplied) near the
alignment marks on the case (see
Diagram).

5811-005-V1

SCREWDRIVER

(CORRECT)

PLACE TIP OF FLAT SCREW

A

DRIVER BETWEEN EDGE OF
BATTERY AND PLASTIC CASE
AS SHOWN. POSITIONING
SCREWDRIVER AT ANY OTHER
CORNER MAY CAUSE DAMAGE
TO DEVICE.

CAREFULLY PRY UP WHILE

B

TWISTING TO REMOVE
BATTERY.

X

5811-006-V1

FEDERAL COMMUNICATIONS
COMMISSION STATEMENT: The user shall

not make any changes or modifications to the
equipment unless authorized by the
Installation Instructions or User Manual.
Unauthorized changes or modifications could
void the user's authority to operate the
equipment.

FCC / IC STATEMENT: This device
complies with Part 15 of the FCC Rules, and
RSS 210 of Industry Canada (IC). Operation
is subject to the following two conditions: (1)
This device may not cause harmful
interference (2) This device must accept any
interference received, including interference
that may cause undesired operation.

Cet appareil est conforme à la partie 15 des
règles de la FCC & de RSS 210 des
Industries Canada. Son fonctionnement est
soumis aux conditions suivantes: (1) Cet
appareil ne doit pas causer d' interferences
nuisibles. (2) Cet appareil doit accepter toute
interference reçue y compris les
interferences causant une reception
indésirable.

REFER TO THE INSTALLATION INSTRUCTIONS
FOR THE RECEIVER/CONTROL WITH WHICH THIS
DEVICE IS USED FOR DETAILS REGARDING
LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

For the latest warranty information, please
visit:

www.honeywell.com/security/hsc/resources/
wa

SPECIFICATIONS

Dimensions

2-1/8” (55mm) x 1-3/16” (30mm) x 1/4”
(7mm)

Operating Conditions

23° F (-5° C) to 120° F (50° C).
Relative Humidity 95%, (non-condensing)

Replacement Battery

Renata/Panasonic CR2032

WARRANTY INFORMATION

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

Copyright © 2011 Honeywell International Inc.

www.honeywell.com/security

Ê800

Ê800----03928V1dŠ

Ê800Ê800

03928V1dŠ

03928V1dŠ03928V1dŠ

800-03928V1 8/11 Rev. A