Ademco 7722TX installation instructions

wm2-2&m
Wireless Zone Sensor
INSTALLATIQN INSTRUCVONS
INTRODUCTION
This wireless
temperature control system, operating
centrally located Spread Spectrum Receiver (Model 7712RX). Zone sensors are installed in areas where temperature control is to be maintained. Ideally, the receiver should be equidistant from all its assigned zone sensors.
The zone sensor measures temperature and periodically transmits that information via RF stgnals to its assigned receiver. The sensor also transmits occupant set point temperature. Other information that can be transmitted includes special service requests, unique serial number of sensor, and status of the batteries in the unit.
RF signals from wireless zone sensors are received by a receiver, which will then send appropriate messages via communication wires to specific equipment assigned to it. This information is also sent to a
central controller for system monitoring.
After mounting each wireless sensor, the Model 7712lT Installation Tool can be used to assign each sensor to a
zane
sensor is designed for use in a
in conjunction with a
.heating
and air conditioning
(TRANE
Figure 1.
n
0
i
Model
Part
No. X13790126060)
Typkal
ii
7722TX
Wireless
Sensor
‘tiooks’
necessary instructions for this are contained in the instructions accompanying the 7712lT Installation Tool.
INSTALLATION Location
Wireless sensors can be installed anywhere on common walls and panitions. Operation will not be affected by metal framing in walls or partitions; however, mounting to solid metal walls or cabinets may reduce the operating distance between the zone sensor and the receiver. Typical line-ot- sight transmission range indoors for sensors is approximately
1OOOfeet
Mounting (Fig. 2)
A mounting plate is provided with the sensor. If attached to the back of the sensor, release it by depressing the ‘locking tab’ at the bottom center of the mounting plate with the blade of a screwdriver, and then sliding the plate downward.
Mount the plate on the selected wall or partition with the VELCRO strips or screws provided. Hooks must point upward (the plate also has the word ‘TOP’ molded into the top side).
Position the sensor onto the mounting plate so that the mounting plate hooks enter the keyhole slots in the back of the sensor, then slide downward to lock the sensor in place.
Battery Installation (Fig. 3)
The sensor uses two 3-volt Lithium batteries (supplied). Remove the sensor cover by squeezing the cover at the top and bottom and then pulling the cover away.
Install one battery in each compartment in the sensor. THE SENSOR WILL NOT OPERATE WtTH ONLY ONE
BATTERY.
Note: Batteries will not seat properly in their compartments if installed incorrectly with regard to polarity. Make sure each battery is fully seated in the compartment and that proper
conted
is being made at each end of the battery.
LCCANG TAB
Fkf~ure 2. Mounting Plate
WSHBlJl
SWrTC
Figure
TON
SIES
GREEN
LED’
LOCKING TAB TO RELEASE SENSOR FROM PLATQ
3. Wireless
(P!AE.SS IN-WAR0
tinsor,
a-w
a4oER
OF
INSTALlATlOh
Cover Removed
(For4
CONNECTION
TOOL)
Removing A Sensor From Its Mounting Plate
To remove a sensor from its mounting plate after installation, press inward on the ‘locking tab’ at the bottom center the left of the the mounting plate. See Figure 3 for location of the locking tab.
&pin
header), and slide the sensor up and
(just
to
off
FUNCTIONAL ELECTRICAL TEST
This
check should be performed after a zone sensor has
been mounted and the batleries installed. The cover must be
Otf.
If
the
sensor is equipped with a temperature control, set the
control dial with
Press either one d the two pushbutton
left
side of
circuit board should flash each time the pushbutton is
pressed. If it does not,
are
property seated in the holders.
In normal use, the green LED will Hash each time the zone
sensor transmits a message,
‘70’
in
the 9 o’clock
position.
switches on
.the
upper
the sensor. The green LED near the bottom of the
check that both batteries are good and
usually several minutes apart.
SPECIFICATIONS
Dlmenslonr: Height:
Range:
Batledes:
4-l/16’ Wiih: 5’ Depth: l-5416’ (not
(103mmH
Nominal Two
3vdl&‘3A
Use only Trane No.
CR123A,
replacement.
Risk of fire, explosion and
incfuding
x
127mmW x 33mmD)
1OOO
feet fine-of-sight, indoors.
Lithium Batteries.
X1377001
Duracell 1234 or Sanyo
mounting plate).
7010, Panasonic
bur’ns.
CR123A
Do not
for
SET-UP PROCEDURE Rater to the
8ccompanylng the Model 771211
sensor set-up procedures In
CHANGES OR MOOIFICATIONS MAOE TO THIS EOUIPMENT WHICH ARE NOT EXPRESSLY APPROVED BY THE AGENT FOR THE RESPONSIBLE FOR COMPLIANCE WITH FEDERAL REGULATIONS COULD
VOID THE USER’S AUTHORITY TO OPERATE THIS EQUIPMENT.
installation
the
instructions
Tool.
USER NOTE
or inctnerate. Dispose of used batteries
TRANE
COMPANY
THE
TFIANE
COMPANY,
Commercial Systems Group
3600
Pammel
Creek Road,
Lacrosse, WI 54602
Copyright
0
1994
Loading...