ADEMCO 4110 Installation Instructions Manual

Download

4110

INSTALLATION

INSTRUCTIONS

N4926VS 4/92 (MARGIN LINES INDICATE PRINCIPAL CHANGES IN THIS ISSUE)

www.PDF-Zoo.com

CONGRATULATIONS

on your purchase of the VANTAGE 4110!

The purpose of these Installation Instructions is to give you a brief overview

of the VANTAGE 4110 system, and provide instructions for installing a basic system.

As always, ADEMCO is there for YOU! Our SALES and TECHNICAL SUPPORT

staff are eager to assist you in any way they can, so don’t hesitate to call, for any reason!

East Coast Technical Support: l-800-645-7492 (8 a.m.-6p.m. E.S.T.)

West Coast Technical Support: l-800-458-9469 (8 a.m.-5 p.m. P.S.T.)

PLEASE,

Before you call Technical Support, be sure you have:

Checked all wiring connections and fuses.

Determined that the power supply and backup battery are supplying proper voltages.

Verified your programming information where applicable.

Noted the proper model number of this product, and the version level (if known) along with any documentation that came with the product.

Your Ademco customer number and/or company name.

Having this information handy will make it easier for us to serve you quickly and effectively.

Again, CONGRATULATIONS, and WELCOME ABOARD!

FOR YOUR CONVENIENCE, two easily removable

Programming

Forms have been included at the

center of this manual.

This

system is not California

State

Fire Marshall approved

and,

as such, should not be used for fire protection in California

(or other areas requiring such acceptance).

TABLE OF CONTENTS

General Information..

......................................

Remote Programming

and Control..

............... .3

Zone Types Available

for Selection..

............... .4

4-Digit Security Codes

...................................

Mounting the

Console(s). ...............................

Wiring Connections..

.....................................

Programming the

Security Control.

................. .7

Specific Address Programming Instructions

... ..B

Testing the System

.......................................

Accessories ................................................

.12

Specifications..

............................................

.13

i’

_ 1’

me Limitations of this

Alarm

System

............. .14

Canadian DOC Statement .............................

FCC Statement

.............................................

Urnited Warranty..

........................................

.16

Diagrams

tnstalting the

Lock (If Used). .............................

Installing the

4110 Circuit Board..

.................... .5

Summary of Connections

................................ 6

Programming

Fon ......................................

.l 0

... ’

-2-

www.PDF-Zoo.com

GENERAL

INFORMATION

The VANTAGE (No. 4110) is a microprocessorbased security control which provides up to 6 wired zones. The security control is housed in a wallmounted metal cabinet measuring 12-112” (316mm) wide x 14-l/2” (366mm) high x Y,(76mm) deep, and can be used with a console equipped wtth a multifunction 1Bkey digital keypad and a numeric and fixed English status LCD display (4127). Optionally, a No. 4137 may be used or a No. 5330 Alpha Console (select for Vector device, as descrfbed in the 5330’s installation instructions) may be used with the control to provide programmable English language zone descriptors and status indications. The system may also be aned and disarmed using a keyswitch.

Connections to the security control are made via a 21-terminal connector block which is used to interface to the wired loops, plug-in transformer, telephone line, remote’ console(s), external alarm sounder(s), etc. The security control can be easily programmed from any of the above remote consoles. Programmed options to establish specific alarm and reporting features are stored in electrically

erasable, non-volatile EEROM memory. This means that the unit can be reprogrammed many times (unlike units equipped with PROMS) and that information which has been programmed will not be lost in the event of a complete loss of power.

The system also provides communication capability (central station repotting, etc.) over existing telephone lines. In addition, it can be uploaded or downloaded via your computer and Hayes Modem.

This system includes an alarm output rated at 2 amps. Throughout the manual, wherever

reference Is made to Alarm Output Ratlngs, they assume a fully charged battery Is connected unless the UL ratlng Is stated.

Zone Characterlstlcs Zones l-6: Programmable Zones, EOLR su-

pervised, N.O. or N.C. sensors, 300-500 msec response.

Zone 3: Past lo-15 msec response

optional.

REMOTE PROGRAMMING AND CONTROL

The No. 4110 can be remotely programmed from an

IBM compatible Personal Computer (PC), a Hayes Modem, and using Ademco’s V-LINK@ Software. Programming the No. 4110 from a remote location fs prot8cted against compromise by using multi-levels of security protection:

Security Code Handshake: An e-digit download ID code must be matched between the No.41 10 and the downloader.

Site Initiated Remote Programming: The installer or subscriber initiates the callback from the subscriber premises (by pressing MASTER CODE + # + 1). All parameters can then be downloaded via the phone fines using a personal computer.

Data Encryption: Data passed between the PC and the No. 4110 is encrypted for sear&y so that it is very difficult for a foreign device tapped into the phone line to take over communication and substitute system comromising information.

Equlpment Requlred: 4110 and console (at premises), an IBM PC compatible computer, a Hayes brand Smamnodem 1200 (Level 1.2 or higher external or Level 1.1 or higher internal style), No. 4130PC

Downloading Soft-ware Diskette (Rev. 1.5 or higher), and appropriate interconnecting cables.

Programmlng: The system uses only two commands, one for uploading and one for downloading.

Notes: After the 4110 and the PC have established valid communication, each console on the system will become inactive. The consoles will become active after the download communication is termfnated.

The detailed operation of the download functions is covered in the installation instructions for the 4130PC Downbad Software Diskette.

Remote Programmlnfl Advlsory Notes:

Alarm and Trouble reporting are disabled during the time that the system and the central station are linked to each other following a valid exchange of codes.

Keypad entries are ignored during the time interval st8t8d above.

Should an alarm occur durlng the remote program Interval, the sytem would not respond to the alarm condltlon.

A copy of the program downloaded may be produced from the IBM PC compatible computer, using the product’s internal report generator, When an optional printer is connected (consult your PC manual for proper printer and connections).

Program Download Time-Less than 45 seconds

for a complete program.

-3-

www.PDF-Zoo.com

ZONE NPES AVAILABLE FOR SELECTION

For each zone used, one of the following zone types must be selected:

Zone Dlsabled EntrylExlt Burglary. Assigned to sensors on

doors through which entry and exit -will normally take place when the system is armed.

Supervlsed Fire With programmable bell timeout. (alarm on short/trouble on open). .Fire zone may not be bypassed. Only usable on Zone 5 or Console Panic.

Perlmeter Burglary. Normally assigned to all sensors on exterior doors and windows requiring instant alarm.

Interlor, Follower. Delayed alarm only if the Entry/Exit zone is faulted first; otherwise, produces an instant alarm. Assigned to zone covering an area such as a foyer or lobby through which one must pass upon entry to reach the keypad to disarm the system. Designed to provide instant intrusion alarm in the event an intruder hides on the premises prior to the system being armed or gains access to the premises through an unprotected area.

Trouble by Day/Alarm

Nlght. Can be

assigned to a zone which contains a foil-pro-

tected door or window (such as in a store), or to a

zone covering a “sensittte’ area such as a stock room, drug suppfy room, etc., or other controlled access area where immediate notification of an entry is desired. During the disarmed state (day),

the system will provide latched Console annunciation (and central station report, if desired) of r\ openings or troubles (such as sensor malfunc- _ /’ tions or foil breaks). During the armed state (night), violations will initiate an alarm.

24=hour Sllent Alarm. This type generally assigned to a zone containing an Emergency button that is designed to initiate an alarm report to the Central Station, but which produces no bcal displays or alarm sounds.

26hour Audlble Alarm. This type also assigned to a zone containing an Emergency button, but which will initiate an audible alarm in addition to an alarm report to the Central Station.

24-hour Auxlllary Alarm (Console sounder only). This type assigned to a zone containing a button for use in personal emergencies, or to a zone containing monitoring devices such as water sensors, temperature sensors, etc. Designed to initiate an alarm report to the Central Station and only provides Console warning sounds and

alarm displays.

Supervised Flre Without programmable bell timeout. (alarm on short/trouble on open). Fire zone may not be bypassed. Only usable on Zone 5 or Console Panic.

&DIGIT SECURITY CODES

Master Security Code: The Installer programs the Master Code initially as part of the programming procedure (see ‘Programming the Securfty Controll). The Master code permits m-entry into the programming mode and also allows access to the norrnaf functions of the system.

I 11 I[ I[ 1 Mamr CoMU=rWs

assigned during programming.

Installer exits programming mode with:

‘98 (prevents re-entry into programming

mode with Master code).

l 99 (allows re-entry Into programming mode

with Master code). 1

By exiting with

96, the only method of getting back into the programming mode from the console is to completely depower the system and follow the procedure noted in the section on “Programming the Security Control”.

The Master security code can be used to assign up to three secondary codes: it can also be used to remove all secondary codes from the system

(individually).

Secondary Security Codes: Secondary security codes are asslgned by Master Code as folbws:

Master Code + CODE key + User # (2 - 4) + Secondary Code

The system will emit a single beep when each

secondary code has been successfully entered. Note: When a secondary code is inadvertently

repeated for different users, or one user’s code is another’s duress code, the lower user number will take priority.

Individual secondary security cpdes can be deleted

by user #l (with Master Code) as follows:

Master Code + CODE key + User # (2 - 4)

Note: All security codes, master and secondary,

permit access to the system for arming, disarming, etc.

www.PDF-Zoo.com

INSTALLING THE LOCK (IF USED)

(The cabinet can be closed and secured wifI?o& a lock by using 2 screws in the covets edge.)

Use Ademco No. N6227 Cam Lock and No. N6227-1 Push-On Clip (Retainer Clip).

1. Remove the cabinet cover. It is easily removable toi servicing and is easily reinstalled.

2. Remove the lock knockout

from the control cabinet cover. Insert the key into the

lock. Position the lock in the hole making certain that the latch will make contact with

the latch bracket when the

door is closed.

3. While holding the lock steady, insert the retainer clip into the retainer slots.

Position cGp as illustrated to

facilitate easy removal.

INSTALLING THE 4110 CIRCUIT BOARD

Note:

BEFORE MOUNTING THE CIRCUIT BOARD, be sure to remove the appropriate metal knockouts from the cabinet. DO NOT ATTEMPT TO REMOVE THE KNOCKOUTS AFTER THE

ClRCUlT BOARD HAS BEEN INSTALLED.

Hang two short mounting

clips -(provided) on the

raised cabinet tabs (see lower detail side view at right).

Insert the top of the circuit board into the slots at the top of the cabinet. Make

sure that the board rests on

the correct row (see the up-

per detail side view at right).

Swing the base of the board

into the mounting clips and

secure the board to the cabinet with the accompanying screws (as illustrated in

fewer detail).

MOUNTING THE 4127 CONSOLE(S)

Separate the console from its backplate by re-

moval of the two screws on the top and bottom

edges.

Use the backpiate to mark the positions on the \ wall for the screw mounting holes and the cutout for the interface wiring. Use wall anchors for the screws and make the cutout in the wall no

larger than indicated on the template. The back-

plate is designed to be directly mounted to either a single or double gang electrical box.

Pull the interface wiring in the wall through the cut-out.

Pass the inte&ce wiring through the opening in the backplate and then mount the backplate to the wall surface with screws.

Splice the interface wiring to the console wires.

Insulated solderless wire splices (such as

Ademco No. 311) may be used for splicing.

Attach the main body of the console to the wall-

mounted backplate. The console is properly attached when it is screwed to the backplate by top and bottom screws.

-5-

www.PDF-Zoo.com

WIRING CONNECTIONS

IMPORTANT:

Do not

connect the battery, or plug in the AC tranaformer, until all other

wiring connections have been completed.

Grounding the System

Terminal 21 is the earth ground connection point. In order for

AC power outlet ground: Available from &prong, 120

f-+-J ‘,,_ ,:

the protective devices in this product to be effective. the

VAC power outlets only. To test the integriiy of the ground

designated terminal must be terminated in a good earth

terminal, use a 3-wire circuit tester with neon lamp indicators.

ground. The following are examples of good earth grounds

such as the UL Listed Ideal Model 61-035. or equivalent,

available at most installations:

available at most electrical supply stores.

Metal

cold water pipe:

Use a .non-corrosive metal strap firmly secured to the pipe to which the lead is electrically connected and secured.

TERMINALS

1 8 2: AC Input from No. 1321m2 plug-in transformer, in

17:

Handset (TIP).

WARNING: To prevent

U.S.A. (16.5VAC. 25VA)

18: Handset (RING).

risk of electrical shock,

NOTE: In Canadian installations. a 1321CN transformer

19:

lnmming Phone Line (TIP).

disconnect telco jack

must be used.

20: lnmming Phone tine (RING).

before servicing unit.

3: Alarm relay output(+), 12VDC. 2.OA maximum (600mA

max. Alarm plus Aux. Power, for UL usage).

21:

EARTH GROUND (a proper earth ground must be provided to protect the system from lightning and

4: Alarm Output I Auxiliary Power I Fire I Console I

Optional Keyswitch (BLACK lead) Ground (-) Return.

electrostatic discharge damage).

t Multiile consoles may be used, but each Ademco 5330

Auxiliary I Fire I Console I Optional Keyswitch (RED) Console must be on an individual home run. Use no more Power: +lPVDC at SOOmA max. t.

than 220’ of 1122 wire or 550’ of tl8 wire.

Data In from Console ! Optional Keyswitch (GREEN)t. RED LEAD:

Battery(+). When AC is present, 13.8VDC

Data Out to Console/Optional Keyswitch (YELLOW$.

is being developed to recharge

gel lead acid battery and

when AC is absent, 12VDC cunent is drswn from the battery.

Zone 1. (When Zones are used, a 1,000 Ohm EOLR Battery lead reversal will blow the battery fuse. should be wired between the farthest sensor connected BLACK LEAD: to the zone terminal and the bw side of the zone.)

Battery (-).

9-l 6: Zone wiring and zone returns.

SUMMARY OF CONNECTIONS DIAGRAM

rrcuIo*uyyI

WARNING:10 =-

PREVENT THE RISK

OF SHOCK, DISCONNECT s TELEPHONE LINE AT Ju) TELCC JACK BEFORE

www.PDF-Zoo.com

Installer options are stored in non-removable, electrically erasable, non-volatile EEROM memory.’ These options must be programmed for the particular installation to establish its specific alarm and reporting features. The security control may be programmed from a remote console.

When programming, the field number will be displayed on the LCD display; also, each entry is displayed as it is keyed in. After programming, values that have been entered in each field can be reviewed and, if necessary, modified.

*Note: It is possible to program the system at any time - even at the installer’s premises prior to the actual installation. Simply apply power temporarily to the control and then program the unit as desired.

When programming from the console, note the following:

Enter the Programming mode by simultaneously depressing the r] and [t] keys within 50

seconds after power Is applled to the

Control, or subsequently by keying the code 4 + 1 +

+ 0 followed by depression of CODE + 0 keys. Once a Master code is programmed, use it instead of 4110 to gain access to the Programming mode.

Immediately following entry into the program mode, 20 will be displayed. (If a 5330 console is

used, 00 will be displayed. Enter ‘20 to access the programming start point). Following the

above

display, the system is ready to accept en-

tries for Address 20. To program a data field, key r] plus Address

(for example, ‘21). then make the required entry. To simply review a data field, key [#I plus Address.

When a data field has been completely programmed, the console will normally %eep” three times and then automatically proceed to, and display, the next data field address to be programmed (if not, key r] plus the address of the next field to be programmed).

If the number of digits that you enter in the data

field is less than the maximum permitted (for example, phone number), then the console will display the last data entered. To proceed, the

next data field address to be programmed must

then be entered (for example, ‘42).

If an address is improperly entered, the console

will display EE. Simply re-enter

or # plus the

number.

The following is a description of commands necessary for programming:

FUNCTION

PROCEDURE

ENTER

1. POWER UP. then deoress PRO&RAMMING MODE:

r] and [#] simultanebusly within 50 seconds of powering up.

Initially, Key: 4 + 1 + 1 + 0

plus CODE key + 0.

After Master Code is pro-

grammed, key: Master

Code + CODE key + 0.

(If ‘98 was used to exit previously, method 1 above mrst be used to enter the program mode again.)

E~!!AAMMING

9 9 (allows rsentty to pro-

gramming mode via Type 3

MODE

entry method above)

9 8 (inhibits re-entry to pro-

gramming mode via Type 3 entry method)

ADVANCE TO FIELD: [1+ ADDRESS (e.g. 21,

35.52, etc.).

PROGRAM FIELD:

m + ADDRESS, followed by data entries.

ERASE FIELDS:

[1+ ADDRESS + r] (only applies 10 Addresses 40

thru 43 and 94.)

READ FIELD:

[#I + ADDRESS

SPECIAL MESSAGES,

oc-

OPEN CIRCUK (no communication between the Console and the Control).

EE -

ERROR (program entry mistake, m-enter the data).

After powering up, AC, dl (disabled) and NOT READY will be displayed after approximately 4 seconds. This will revert to READY in appx. 1 minute, which allows PIRS, etc. to stabilize. To bypass this delay, press: # + 0.

-7--

www.PDF-Zoo.com

SPECIFIC ADDRESS PROGRAMMING INSTRUCTIONS

Note: The followlng shows Factory Default Settings withln brackets: [ ]

1 THE PROGRAMMING FORM PRINTED ON PAGE 10 CAN BE USED TO RECORD THE DATA FOR THIS INSTALLATION

[

DIALER PROGRAMMING (‘40.•48)

SYSTEM

ARMING (*20-•23)

l 20

l 21 ‘22 ‘23

ZONE ‘30

MASTER SECURITY CODE [4][1][1][0] Enter 4 digits, O-9 (entry of all 4 is mandatory). Use of a ‘9” in the last

position inhibits the Ambush feature.

QUICK ARM ENABLE [0 ] Enter 1 for enabled or 0 for disabled

KEYSWITCH ENABLE [0 ] Enter 1 for enabled or 0 for disabled

FORCED BYPASS ENABLE [0 ] Enter 1 for enabled or 0 for disabled

RESPONSE PROGRAMMING l 29-•39

ALARM BELL TIMEOUT

[l ] External sounder will shut off after time allotted. Enter 1 digit.

No timeout = 0

8 minutes = 2

4 minutes = 1.

12minutes=3

Use the foiiowlng table of zone types for programming addresses l 31-•37

O= Zone Disabled I= ENTRYIEXfT, Burglary 2= FIRE (w/timeout) 3= PERIMETER, Burglary

4= INTERIOR, FOLLOWER, Burglary

5.: TROUBLE BY DAY/ALARM BY NIGHT, Burglary 6- 24 Hr (Silent) 7= 24 Hr (Audible) 8=24Hr (Aux) 90 FIRE (w/o timeout), Fields ‘35 & l 37 only

‘31 l 32

‘33 ‘34 ‘35 ‘36 *37

‘38

‘39

RESPONSE TYPE [l ] Enter 1 digit

RESPONSE TYPE [4 ] Enter 1 digit

RESPONSE TYPE [3 ] Enter 1 digit

RESPONSE TYPE [2 ] Enter 1 digit,

RESPONSE TYPE [7 ] Enter 1 digit

RESPONSE TYPE (Console Panic) [6 ] Enter 1 digit

FOR ZONE

Only zone types 0.2,6,7,8,9 applicable. ENTRY/EXIT DELAY

[2 ] System will wait the time allotted before sounding alarm upon entering. Enter 1 digit.

Exit delay = Entry delay plus 15 seconds

0 = 0 seconds

2 = 30 Seconds

1 = 20 Seconds

3 = 45 Seconds

ZONE 3 RESPONSE TIME TO OPEN [ 0) 400 ms nominal = 0

10msnominal =l

l 40

‘41

‘42

‘43

‘44

‘45

‘46 ‘47

PABX ACCESS CODE [ ] [ ] [ ] [ ]

Enter 4 digits, O-9, for each PABX digit needed to access an outside line. To skip this field, enter l . If

is entered, no PABX number will be dialed and nothing will appear in this field. End field by entering ‘41 if not filled. To clear entries from field, press ‘40’.

PRIMARY PHONE No.

I I[ I[ I[ 11 I[ I[ II II II Ii I[ 1

Enter

to 12 diaits. O-9. Do not fill unused spaces: End field-by entering ‘42 if not filled. To clear entries from field, press ‘41’.

Note: Back-up reporting (8 calls are made to the secondary phone number if no acknowledgment is received after 8 attempts to the prfmary number) is automatic only ff there is a secondary phone number.

SECONDARY PHONE No.

1 I[ I[ I[ I[ 11 I[ I[ I[ I[ I[ I[ 1

See

above.

End fiekf by entering ‘43 if not

filled. To dear entries from field, press l 42’. SUBSCRIBER ACCT. No.

(151[15][ 15x151

Enter digits O-9; #+l l=B; #+12=C;

#+13=D; #+14=E: or #+lS=F. Enter

as the

fourth digit if a 3 digit accf no. (for 3+1 dialer

reporting format) is used. Enter 0 as the first

digit of a 4-digit acct no. for nos. OOOO-

0999. End field by entering ‘44 if only 3 digits are used. To clear entries from field, press ‘43’.

REPORT FORMAT f 0 ] Determine which format is to be used to

report to central station. Enter 1 digit.

0 = 3+1; 4+1 ADEMCO US Standard

1 - 3+1; 4+1 Radionics Standard 2 = 4+2 ADEMCO Lo Speed Standard

3 = 4+2 Radionics Standard

6 = 4+2 ADEMCO Express 8 = 3+1; 4+1 ADEMCO Lo Speed Expanded 9 = 3+1; 4+1 Radionics Expanded

(Enter

as the 4th digit of l 43 if 3+1 dialer

reporting is to be used.) PHONE SYSTEM SELECT [ 0 ]

Enter 1 digit. If Central Station Rcvr is rxrr on WATS tine:

0 = Pulse Dial 1 = Tone Dial ff Central Station Rcvr is on WATS line:

2 = Pulse Dial

3=ToneDial

FUTURE USE [0]

Enter 0.

15 SECOND DELqY ;;i BURG [ 0 ] O-NO

-8-

ConCnu8d on PaQe 9 e

www.PDF-Zoo.com

4110 PROGRAMMING FORM

FIELD FUNCTION

PROGRAMMED VALUES

SYSTEM ARMING (‘200’23)

‘20

MASTER SECURflY CODE

0Elncl

Enter 4 digits, O-9

‘21 GUlCK ARM ENABLE

t 0 0 I no. 1 I yes

‘22

KEYSWITCH ENABLE

+Elo

I no, 1 -yes

‘23 FORCED BYPASS ENABLE

t f-J O-no,1 -yes

‘31 ‘32 ‘33 ‘34 ‘35

‘36

ZONE 1 RESPONSE TYPE

ZONE TYPES FOR PROGRAMMING FIELDS ‘31-37

0 (or undefined) - Zone Disabled

ZONE 2 RESPONSE TYPE 11 ENTRY/EXlT. Burglary

2 I FIRE with timeout

ZONE 3 RESPONSE TYPE

3 I PERIMETER, Burglary

ZONE 4 RESPONSE TYPE

4 - INTERIORIFOLLOWER, 8urglary 5 I TROUBLE BY DAY/ALARM BY NIGHT, Burglary

ZONE 5 RESPONSE TYPE

6 I 24 Hr (Silent) 7 - 24 Hr (Audible)

ZONE 6 RESPONSE TYPE

8 = 24 Hr (Auxiliary)

9 I FIRE without timeout (Fields ‘35 and ‘37 only)

. .

ZONE 7 RESPONSE TYPE

CONSOLE PANIC. Onty zone types 0.2,6,7,8,9 applicable.

ENTRY DELAY

i-f q

0=0sec;1=20sec;2r30sec;3=45sec

EXlTDelay=ENTRYDetay+lSsec

ZONE 3 RESPONSE TO OPEN

t 0 0 I 400 ms nominal; 1 - 10 ms nominal

ZONE RESPONSE PROGRAMMING (*29=39)

‘30 ALARM BELL TtMEOUT

tt q

O=none;l

=4min;2=8min,3=12min

‘37 ‘36

‘39

DIALER PROGRAMMING (*40-•47)

‘40

‘41

‘42

PABX ACCESS CODE

clclocl

Enter 4 digits, O-9. ff fewer than 4 digits entered, exit by

pressing

(and press 41, lf entering next field). To clear entriis from field, press ‘40’.

PRIMARY PHONE No.

nnnnnnnnnnnn Enter upto 12digits. O-

9. Do not fill unused spaces. If fewer than 12 digits entered, extt by pressing

(and press 42, if entering next

field). To clear entries from field, press ‘41’.

SECONDARY PHONE No.

nnnnnnnnnnnm Enter upto 12digits, O-

9. Do not fill unused spaces. If fewer than 12 digits entered, exit by pressing

(and press 43, if entering next

field). To clear entries from field, press ‘42’.

‘43

SUBSCRIBER ACCOUNT No.

EIxzlII

Enter O-9; #+l 1 for B; #+12 for C:#+l3

for D; #+14 for E: #+15 for F. lf only 3 digits used. exit by pressing

(and press 44, if entering next field). To

clear entries from field, press ‘43’.

Examples: For Acct No. 1234. enter: m /2) -1 7)

For Acct No. 8234. enter: rf 121 131 141

‘44

REPORT FORMAT

For Acot No. 123.

enter:

17 121 131 1’1

Enter ’ as the 4th digit of ‘43 if 3+1 dialer reporting is to be used.

0 I 3+l, 4+1 ADEMCO LJS STANDARD 6 or unshed = 4+2 ADEMCO EXPRESS 1 I 3+1.4+1 RADIONICS STANDARD

6 = 3+1,4+1 ADEMCO US EXPANDED 2 = 4+2 ADEMCO US STANDARD 9 = 3+1,4+1 RADtONlCS EXPANDED 3 = 4+2 RADIONICS STANDARD

‘45

l 46 l 47

PHONE SYSTEM SELECT

tf 0 lf Cent. Sta. IS NOT on a ‘WATS time:

0 = Puke Dii; 1 = Tone Dial

H Cent. Sta IS on a WATS line: 2 I Pulse Dii; 3 I Tone Dial

FLmJREu8E

t 0 Enter 0.

15 SEC DlALER DELAY (BURG) t 0 0 = no, 11 yes

t If a number other than

or 1 is entered. even numbers = same as 0; odd numbers = same as 1. ff If a number greater than 3 is entered, the control will subtract multiples of 4 to gel to the allowable pro9rarn range. 41 lOPRV2 4IQ2 (See Insauctions N4926VS)

OVER*

www.PDF-Zoo.com

RESTORE REPORT CODES (‘51-‘74):

Wlth a 3+1 or 4+1 Standard F&mat: Enter a code in the first box: l-9, 0, B. C, D, E, or F. Enter [#+lO] for 0, [#+ll) for 8, [t+l2] for C. [#+13) for D, [#+14] for E. [#+15] for F.

A [0] (nor [#+lO]) in the first box will disable a report.

A [0] (nor [#+lO]) in the second box will result in auto&tic advance to the next fiik! when programming.

With an Expanded or 4+2 Format: Enter codes in

both

boxes (1st and 2nd digits) for 1-9, 0, or B-F, as de-

scribed above.

A [O] (not [#+lO]) in the second box will eliminate the ex-

panded message for that report. A [O] (not [#+lO]) in horh boxes wilt disable the repon. Examples: For Code 3 (Smgle D@it). enter: )3)

For Code 32 (Two Digits). enter: 131

121

For Code B2 (Hexadeama!) enter: IkllJ

12)

ALARM REPORT CODES (c51-‘59)

‘51 ‘52 ‘53 ‘54

‘55

‘57

‘56

‘59

SYS

‘60 ‘61 ‘62 ‘63 ‘64 ‘65 ‘66

ZONE 1 ALARM FIEPOFIT CODE

III

ZONE2AlARMREPORTCODE rjil

ZONE 3 AIARM REPOFtT CODE

1-i II

ZONE4AlARMREPORlCODE

IIrj

ZONE5ALARMFtEPORTCODE

IIT1

ZONE 6 ALARM REPORT CODE

II rj

ZONE7AfARMREPORTCODE~ nr1

(Console Panic)

ZONE8AlAFIMFU’OFlTCODE

nr1

(Duress)

ZONE 9 AIARM REPORKC~)

I-III

STATUS RPT CODES (‘SO-‘66)

TROUBLE REPORT CODE

III

BYPASS REPORT CODE

ElII

AC LOSS REPORT CODE

III

LOW BAT REPORT CODE

III

TESTREPOFfTCODE

III

OPEN REPORT CODE

l-t-t

CLOSE REPORT CODE

I . .

TTT 2nd diiit is automatically sent as the user

number if expanded or 4+2 reporting is

RESTORE RPT CODES (‘70=74)

‘70 ALARM RESTORE RPT CODE

cl 2nd digit is automatically sent as the 2nd digit of the zone alarm report code

programmed in ‘51-‘59, if expanded or 4+2 reporting is selected.

‘71 TROUBLE RESTORE RPT CODE

[I I]

BYPASS RESTORE RPT CODE

III

‘73 AC RESTORE RPT CODE

III

‘74

LOWBATRESTORERPTCODE

IT1

DOWNLOAD INFO (‘94=97)

‘94 r;y,Pli;“;No.l ]“, ,, I, ,I ]

Enter up to 12 digits, O-9. Do not fill unused spaces. H fewer than 12 digits entered, exit field by pressing

(and press 95. if entering next field). To clear en-

tries from field, press ‘94’.

‘96 INITIALIZES DOWNLOAD ID, SUBSCRIBER

ACCOUNT No. FOR INITIAL DOWNLOAD No entry required.

‘97 ZEROS ALL PROGRAM FIELDS

No entry required.

TO EXIT PROGRAM MODE (‘98 or ‘99)

Press ‘98 or ‘99 if exiting programming, or next field number if wntinuing.

‘98

EXRS PROGRAMMING MODE and prevents re-entry by: Master Code + Code + 0.

(‘71

IX ,/

‘99 EXmS PROGRAMMING MODE and

elkws re-entry by: Master Code + Code + 0:

411 OPRVP 4192 (See Instructions N4926V5)

www.PDF-Zoo.com

~~EMcoJ

4110 PROGRAMMING FORM

FIELD

FUNCTION PROGRAMMED VALUES

SYSTEM ARMING (‘20~‘23)

‘20 ‘21 ‘22 ‘23

ZONE

‘30 ‘31

‘32 ‘33 ‘34

‘35 ‘36

‘37 ‘38

l 39

MASTER SECURITY CODE

17000

Enter 4 digits, O-9

QUICK ARM ENABLE

q-Jo

I no, 1 = yes

KEYSWTTCH ENABLE

tcJo

*no,1 -yes

FORCED BYPASS ENABLE

tOo

-no,1 -yes

RESPONSE PROGRAMMING (*29=39)

AIAFIM BELL TtMEOUT

CJO

=none;1=4min;2=8min,3=12min

ZONE 1 RESPONSE TYPE

’ ZONE TYPES FOR PROGRAMMING FIELDS ‘31.37

0 (or undefined) I Zone Disabled

ZONE 2 RESPONSE TYPE

1 - ENTRY/EXIT, Burglary

2 - FIRE with timeout

ZONE 3 RESPONSE TYPE

3 I PERIMETER, Burglary

ZONE 4 RESPONSE TYPE

4 = INTERIOR/FOLLOWER. Burglary 5 I TROUBLE BY DAYIAIARM BY NIGHT, Burglary

ZONE 5 RESPONSE TYPE

6 I 24 Hr (Silent) 7 I 24 Hr (Audiie)

ZONE 6 RESPONSE TYPE

ZONE 7 RESPONSE TYPE

CONSOLE PANIC. Onfy zone types 0.26.7.8.9 applicable.

ENTRY DELAY t’t 0 O-Osec;1-2Osec;2-3osec;3~45sec

EXIT Delay = ENTRY Delay + 15 set

ZONE 3 RESPONSE TO OPEN t 0 0 I 400 ms nominal; 1 I 10 ms nominal

DIALER PROGRAMMING (*40-•47)

‘40

PABX ACCESS CODE

0000

Enter 4 digits, O-9. tf fewer than 4 digits entered, exit by

pressing

(and press 41, if entering next field). To clear entries from field, press ‘40’.

PRIMARY PHONE No.

nnnnnmnnnnnn Enter up to 12 digits, O-

9. Do not fill unused spaces. If fewer than 12 digits entered, exit by pressing

(and press 42. if entering next

field). To clear entries from field, press ‘41’.

‘42 SECONDARY PHONE No.

nnnnnnnnnnnn Enter upto 12digitq O-

9. Do not fill unused spaces. N fewer than 12 digits entered, exit by pressing ’ (and press 43, if entering next field). To clear entries from field, press ‘42’.

l 44

REPORT FORMAT

l 43

SUBSCRIBER ACCOUNT No.

IIIIIII

Enter O-9; #+l 1 for 8; #+12 for C:#+l3

for 0: #+14 for E; a+15 for F. If only 3 digits used, exit by pressing

(and press 44, if entering next field). To

clear entries from field, press ‘q3’.

Exmpks: For Acu No. 1234, enmr: 1’ 121 m 14(

For Acct No. 8234, entar: ml 121 131 141

For Acct No. 123,enter: m 121 131 1’1

Enter ’ as the 4th diiit at ‘43 if 3+1 dialer reporting is to be used.

OP~+~,~+~ADEMCC~J~STANDARD

6 or u&fined = 4+2 ADEMCO EXPRESS

I= 3+ t ,4+1 RADICNICS STANDARD

6 6 3+1.4+1 ADEMCO l.S EXPANDED

2 = 4+2 ADEMCO L’S STANDARD

9 = 3+1.4+1 RADIONICS EXPANDED

3 = 4+2 RADIONICS STANDARD

‘46 ‘47

PHONE

SYSTEM

SELECT

fl 0 ff Cent. Sta. IS NOT on a WATS line: 0 - Pulse Dial; 1 -Tone Dii

if Cent. Sta. IS on a WATS line: 2 I Pulse Dial; 3 = Tone Dial

FUTURE USE t 0 Enter 0.

15 SEC DIALER DELAY (BURG) t 0 0 I no, 1 I yes

t~anumbero~thanOor1isentered,evennumben=sameasO;oddnumbers=~asl. tt If a number greater than 3 is entered. the controi will rubtract multipie of 4 to get to the allowable program range. 41 lOPRV2 4192 (Sea Instructions N4926VS)

OVER*

www.PDF-Zoo.com

‘TO PROGRAM ALARM, SYSTEM STATUS, AND

RESTORE REPORT CODES (‘51=74):

With a 3+1 or 4+1 Standard Format: Enter a code in the fkf box: l-9.0. B. C, D. E, or F. Enter (#+lO] for 0. p;] for B, (#+12] for C. [#+13] for D, (#+14] for E. (#+15]

A (01 (not [#+lO]) in the first box will disable a report.

A [O] (not[#+lO]) in the secondbox will result in automatic

advance to the next field when programming.

With an Expanded or 4+2 Format: Enter codes in

bofh boxes (1st and 2nd digits) for l-9. 0, or B-F, as de-

scribed above.

A [O] (not [#+lO]) in the second box will eliminate the ex-

panded message for that report.

A IO] (norM+lOl) in both boxes will disable the report.

Exemplee: For Code 3 (Single Digit), enter: 131 -1

For Code 32 (Two Digits), enter: 131 12)

For Cc& 82 (Hexadecimal) enter: (m r[

ALARM REPORT CODES (*51=59)

‘51

ZONE 1 ALARM REPORTCODE mr[

‘52

ZONE2ALARMREPORTCODE mr[

‘53 ZONE 3 AIARM REPORT CODE m rI

‘54

ZONE4AlARMREPCRTCCDE III1

‘55 ZONE5AlAFtMREPORTCODE nII-1

‘56

ZONE6ALARMREPORTCODE Tit-1

‘57 ZONE 7 ALARM REPORTCCDE I-II]

(Console Panic)

‘58

‘59

SYS

80 ‘61 ‘82

‘84 ‘65 ‘66

STATUS RPT CODES (‘SO-•66)

TFOUBLE REPORT CODE

III

BYPASS REPORT CODE

III

AC LOSS REPORT CODE

III

LOW BATREPORT CODE

TEST REPORT CODE

III

OPEN REPORT CODE

ttt

CLOSE REPORT CODE

ttt

m 2nd digii is automatically sent as the user

number ff expanded or 4+2 reporting is selected.

RESTORE RPT CODES (‘70=74)

‘70 ALARM RESTORE RPT CODE

2nd digit is automatically sent as the 2nd digit of the zone alarm report code

programmed in ‘51-‘59. if expanded or 4+2

reporting is selected. ‘71 TROUBLE RESTORE RPT CODE 11 II ‘72

BYPASS RESTORE RPT CODE

III

‘73 AC RESTORE RPT CODE

III

‘74 LOW BAT RESTCRE RPT CODE n I1

DOWNLOAD INFO (*94=97)

l 94 ~AD~yyl.( ,I I, I, ,I I, ,

Enter up to 12 digits, O-9. Do not fill unused spaces. If fewer than 12 digits entered, exit field by pressing

(and press 95, if entering next field). To clear en-

tries from field, press ‘94’.

‘96

INfTlALQES DOWNLOAD ID, SUBSCRIBER ACCOUNT No. FOR INfTlAL DDWNLOAD No entry required.

‘97 ZEROS ALL PROGRAM FIELDS

No entry required.

TO EXIT PROGRAM MODE (‘98 or l 99)

Press ‘98 or ‘99 if exiting programming, or next field

number if continuing.

‘98 EXITS PROGRAMMING MODE and

Prevents m-entry by: Master Code + Code + 0.

‘99

EXTTS PROGRAMMING MODE and aIows m-entry by: Master Code + Code + 0.

4 11 OPRVP 4J92 (See Instructions N4926V5)

www.PDF-Zoo.com

* Continuad from Page 3

The Alarm. System Status and Restore Reporl Codes shown in fields ‘Sl-‘74 in the following sections may be designated to rapon to the central station in any of the above fats.

The 3+1 and 4+1 Standard formats comprise a 3 for 4)

digit subscziber number and a single diiit reporl code (e.g. Alarm. Trouble, Restore, Open, Close).

The 3+1 and 441 Expanded formats comprise a 3 for 4) digit subsaiber number, and a single digit report code, followed by a second line where the report cada is repeated 3 (or 4) times and followed by another number (normally the zone number) or user ID related to that report

The 442 formats comprise a 4 digit subscriber number and single digit report code. immediitety followed by the zone number (nonally) or user ID.

3411441

4+2

Bypass

AC Loss

TO PROGRAM ALARM, SYSTEM STATUS, AND RESTORE REPORT CODES (Fields ‘51.‘74):

With a 3+1

or 441

Standard Format: Enter a code in the first box: l-9, 0. B, C, D. E. or F. Enter (X+10] for 0, (#+ll] for 8, [#+12] for C, [#+13] for D. [#+14] for E. (#+15] for F.

A (01 (not (#+lO]) in the fifsl box will disable a report. A [0] (not [#+lO]) in the second box will resuli in automatic

advance to the next field when programming. With an Expanded or 4+2 Format: Enter codes in both

boxes (1st and 2nd digits) for l-9,0, or B-F, es described above. A (01 (not (W+lO]) in the second box will eliminate the expanded

message for that report. A 101 (not

I#41

01) in both boxes will disable the report.

See examples on programming form.

ALARM REPORT CODES

S=(S) A

ssssbu

JWA) 2

(Fields

51 - *Se)

ssso f

SSSSTt

5 1 ZONE 1 ALARM CODE

l-mnt

IO I 10 1

izgb” -8b

‘52 ZONE 2 ALARM CODE

IO I (0 I

sss(SlE -h

53 ZONE 3 ALARM CODE

EWEI &

(0 I (0 1

54 ZONE 4 ALARM CODE

Lowaatl

ClOSe Test Resmre

A&ml

AC Restore

Lo8at Res.

Trouble Ftes.

Bypass Res. WllWtX

=SS) T =w 8 sss(S) E

=ev L

SYSTEM STATUS CODES (Fields

60 - ‘66)

‘60 TROUBLE CODE ‘61 !%!SS ’ CODE

62 !t&SS CODE

IO I (0 I

‘63 LO BAT CODE

sss(S) L

-4

(0 I 10 I

LLLfu La

‘55 ZONE 5 ALARM CODE

‘64 p&] RPT CODE

-7-. -

sss(s)O -0i.f

ooo(O) u

sssoc

SSSSCU cccou sss(s)G s86sGa

P I P I

58 ZONE 6 ALARM CODE

IO I (0 I

‘57 ZONE 7 ALARM CODE

CONSOLE PANIC

.- . .a .

‘65 ii&i! RPT CODE

(0 ] (2nd digit I User (I)

66 CLOSE RPT CODE

(0 ] (2nd digit - User #)

SsasPz

-AA,

- RLLB

I” 1 1” 1

‘58 ZONE 8 ALARM CODE

DURESS 10 110 1 I

‘59 iONE 9 ALhFiti ‘CODE

TAMPER [O ] (0 ]

(Fi Id ‘70 - -74)

‘70 ALARM RESTORE RPf :O:E IS1 DIGIT

101(2nd dinit normaflv zone 61 When set to 0. all restores are

-e -R-T’

b&&d. The 2nd dii of an alarm restortz-2 digif report is the

fv+ww

same as the 2nd digit of the alarm repoti being restored as

=-Rg -w

found in fields ‘51. ‘59.

WWWW

‘71 TROUBLE RESTORE CODE

(01 (01 ff the 1st digit is sel to 0. reporting is disabled. Trouble

SSSorSSSS= SubsuibarID

A= Alarm Code-1st digit

2s T~bcatI~ Zone

Number--2nd diiit

Tt P

Tiibk-code (1st a 2nd digits j

EABE=

Bypass Code (1st 6 2nd digits) AC Loss Code (1st 6 2nd digits)

LLB

Low 8aUery Code(lrt 6 2nd digits)

0 5 Open Code-1st Digit

C= Close -1st Dioit

U= UserNumber(lst~2nddigik)

Gg =

Test Code I1 st 6 2nd diaik)

-R=

Restore C&e (Alarm)15 6.2nd digits

RTt = bslore Coda (TrM)l st 6 2nd digits

R8 b = Restore Code (8yps)l st 6 2nd digits

RAAC =

Restore Code (AC) 1 st 6 2nd digits

ALL 8 = Restore Code (8at)lst 6 2nd diiik

‘Zone numbers for: [‘I 6 (#] = 7

Duress = 8 Tamper= 9

restore is reported only if a//troubles in the system are restored.

‘72 BYPASS RESTORE CODE

(01 (01 ff the 1st digit is set to 0, reporting is disabled.

73 AC RESTORE RPT CODE

(01 (0] if the 1st digit is set to 0. reporting is disabled.

74 LO BAT RESTORE CODE

(01 (01 If the 1st digit is set to 0, reporting is disabled.

DOWNLOAD INFORMATION (*94-•97)

94 DOWNLOAD PHONE NUMBER

[ I[ I[ I[ Ii II II I[ I[ I! I[ II I

Enter up to 12 digits: O-9. Do not fill unused spaces. End field by entehng ’ if not filled. To clear entries from iield, press ‘94’.

‘96 INITIALIZES DOWNLOAD ID AND SUBSCRIBER

ACCT. No. FOR DOWNLOADING (No entry required)

97 ZEROES AU PROGRAM FIELDS (No entry required)

TO EXIT PROGRAM MODE p96 or

99)

Press ‘98 or ‘99 if exiting programming, or next field number if continuing.

‘98 EXITS PROGRAMMING MODE and

prevents re-entry by: Master Code + Code + 0.

‘99 EXITS PROGRAMMING MODE and

allows re-entry

by:

Master Code + Code +

-9-

www.PDF-Zoo.com

4110

PROGRAMMING FORM

FIELD

FUNCTION PROGRAMMED VALUES

SYSTEM ARMING (‘20~~23)

‘20 MASTER SECURflY CODE

.OclclU

Enter 4 digits, O-9

‘21 OulcK ARM ENABLE

+I30

-no, 1 -yes

‘22

KEYSWITCH ENABLE

+I3

rno.l -yes

‘23

FORCED BYPASS ENABLE

+I30

-no,1 -yes

ZONE RESPONSE PROGRAMMING (‘29=39)

‘30

AlARMBELLnMEoUT

++ q

O=n0na;l

=4min;2-8min,3-12min

‘31

ZONE 1 RESPONSE TYPE

ZONE TYPES FOR PROGRAYUING FIELDS VI-37

‘32

ZONE 2 RESPONSE TYPE

0 (or undefined) = Zone Disabled 1 I ENTRY/EXIT. Burglary 2 I FIRE with timeout

‘33

ZONE 3 RESPONSE TYPE

3 - PERIMETER Burglary

‘34

ZONE 4 RESPONSE lYPE

4 I INTERlOR/FOLLOWER. Burglary 5 - TROUBLE BY DAY/ALARM BY NIGHT, Burglary

'35

ZONE 5 RESPONSE TYPE

6 I 24 Hr (Silent)

7 I 24 Hr (Audiie)

'36

ZONE 6 RESPONSE TYPE

8 I 24 Hr (Auxiliiry) 9 I FIRE without timeout (Fields ‘35 and ‘37 only)

'37

ZONE 7 RESPONSE TYPE

CONSOLE PANIC. Only zone types 0,2,6,7,8.9 applicable.

'38

ENTRY DELAY

++ c] 0=0sec,;1=20sec;2=30sac;3=45sec

EXIT Delay = ENTRY Delay + 15 sac

‘39

ZONE3RESPONSETOOPEN +

0~400msnominal;1=10msrmminal

DIALER PROGRAMMING (*40-•47)

l 40

PABX ACCESS CODE

cl0cl0

Enter 4 digits. O-9. ff fewer than 4 digits entered. exit by

pressing

(and press 41, if entering next field). To clear entries from field, press ‘40’.

‘41

PRIMARY PHONE No.

nnnnnnnnnnnn Em upm 12dWs. O-

9. Do not fill unused spaces. ff fewer than 12 digits entered, exit by pressing

(and press 42, if entering next

fiild). To dear entries fmm fiifd, press ‘41’.

42 SECONDARY PHONE No.

nnnnnnnnnnnri Enterupml2dk$s,O-

9. Do not fill unused spacxts. H fewer than 12 digits entered, exit by pressing

(and press 43, if entering next

field). To dear entries from field, press ‘42’.

‘43

SUBSCRIBER ACCOUNT No.

OOIIII

Enter O-9; 6+11 for 8; kl2 for CM13

for D; 6+14 for E; #+15 for F. If only 3 diiits used, exit by pressing ’ (and press 44. if entering next field). To dear entries from field. press ‘43’.

‘44

REPORTFORMAT

Exmpkw: For Accl No.

1224. enter: LT 121 131 14(

For Acu No.

8234. enter: ) 121 131 141

For ~cct No. 123, enter: 1-i-l 121 m 1’1

Enter

as the 4th digit of ‘43 if 3+1 dialer reporting is to bs used.

0 = 3+1. kl ADEMCO Us STANOAR

6or-=4+2ADEMCOEXPRESS

1 - 3+1.4+1 R4DIoNlcs STANDARD

6 I 3+1.4+1 ADEMCO U8 EXPANDED

2=4+2AoEMcoussTANDARo

9 = 3+1, kl RADIONICS EXFANDED

3 - 4+2 RADIONICS srANMRo

l 45

‘46 '47

PHONE SYSTEM SELECT

fi OH Cent.Sta. ISNOTona WATS line: 0 -PulseDial; 1 -ToneDi

If Cent. Sta. IS on a WATS fine: 2 I Pulse Dii, 3 I Tone Dial

FUTURE USE

+ 0 Enter 0.

15 SEC DLALER DELAY (BURG) + 0 0 = no, 1 I yes

www.PDF-Zoo.com

TO PROGRAM ALARM, SYSTEM STATUS, AND’ RESTORE REPORT CODES (‘51-‘74):

Wlth

3+1 or 4+1 Standard Format: Enter a code

in the first box: l-9.0. B, C, 0, E, or F. Enter [#+lO] for 0, [#+ll] for B. [#+12] for C, [#+13] for 0, [#+14] for E, (r&15] for F.

A IO] (not [#+lO]) in the f&box will disable a report. A [O] (nor [#+lO]) in the secondbox will result in automatic

advance to the next field when programming.

Wlth an Expanded

or 4+2

Format:

Enter codes in both boxes (1st and 2nd digits) for 1-9, 0, or B-F. as described above.

A [O] (nor [#+lO]) in the second box will eliminate the expanded message for that report.

A (01 (nor f#+lOl) in both boxes will disable the report.

Examples:

For Code 3 (Single Diiit). enter: v1

For Code 32 (Two Diiits). enter: l- 1-2

For Code 82 (Hexadecimal) enter: [m 121

ALARM REPORT CODES (‘51-‘59)

‘51 ‘52 ‘53 ‘54 ‘55 ‘56 ‘57

ZONE 1 AJARM REPORTCODE

mrj ZONE2AlARMREPOFlTCODE mr1 ZOf’IE3ALARMREPORTCODE mr(

ZONE4ALAJ?MREPORTCODE III1

ZONE5AlARMREFORTCODE [rl[

ZONE6AfARMREPOfTrcoDE

IlI[

ZoNE?kuAlwREPoKrcoDE

(Console Panic)

Ill]

ZoNE8ALARMREPoRTcQDE 1111

(Duress)

zmEg~~-y=) III

STATUS RPT CODES (*60-‘66)

TROUBLEREPORTCODE

III

BYPASS REPORTCODE

III

AC LOSS REPORT CODE

ElII

LOW BAT REPORT CQDE

III

TESTREPORTCQDE

III

OPENREPORTCODE

ttt

CLOSE REPORT CODE

ttt

m 2nd diit is automatically sent as the user

number if expanded or 4+2 reporting is selected.

‘56

‘59

SYS

‘60 ‘61 ‘62

‘63 ‘64 ‘65 ‘86

RESTORE RPT CODES (*70=74)

‘70

AIARM RESTORE RPT CODE

2nd digit is automatically sent

the 2nd digit of the zone alarm report code programmed in ‘51-X9, if expanded or 4+2 reporting is selected.

‘71

TROUBLERESTORERPTCOOE Ilr[

‘72

BYPASS RESTORE RPT CODE

III

‘73 AC RESTORE RPT CODE

III

l 74

LOWBATRESTORERPTCOM mr[

DOWNLOAD INFO (+94=97)

l 94

DOWNLOAD PHONE No.

q cloonnclclcllJocl

Enter

to 12 digits, O-9. Do not fill unused spaces.

ff fewer than 12 diiits entered, exit fiefd by pressing

(and press 95. if entering next field). To clear en-

tries from field, press ‘94’.

‘96 lNlTlALlZES DOWNLOAD ID, SUBSCRfBER

ACCOUNT No. FOR INflTAL DOWNLOAD

No entry required.

‘97

ZEROS ALL PROGRAM FIELDS

No entry required.

TO EXIT PROGRAM MODE (‘98 or l QQ)

Press ‘98 or ‘99 ff exiting programming, or next field number if continuing.

‘98 U(fT5PROGRAMMlNGMODEand

preVenrs reentry by: Master Code + Code + 0.

‘99

EXRS PROGRAMMING MODE and aUows reentry by: Master Code + Code + 0.

-ll-

www.PDF-Zoo.com

TESTING THE SYSTEM

After

installation is completed, the Security System

should be carefully tested.

1. With the System in the disarmed state, check that all zones are intact. If NOT READY is displayed, press the r] key to display the faulted zone(s). Restore faulted zone(s) if necessary, so that READY is displayed. Fauff and restore every sensor individually to assure that it is being monitored by the system.

2. Enter the security code and press the TEST key. The external sounder (if used) should sound for 1 second and then turn off each time a contact is faulted.

test report should be transmitted (if programmed) to the Central Station immediately. If the backup battery is discharged or

missing, the external sounder. will not turn on and a LOW BATTERY report will be transmitted instead of a TEST report. The keypad will beep once per minute to indicate that the system is in

the Test Mode.

3. Battery Test: For UL Listed Household fire/burglary installations, a Battery Test Switch

(Ademco No. 1206) must be installed next to the Control, so that the system’s backup battery can be tested periodically (at least weekly). To test the battery, enter test mode as described in step

2 above and check that the POWER LED is on,

indicating the presence of AC power in the system. Momentarily depress the Battery Test Switch. If the battery is operational, the POWER

LED will go out, but the system will remain in the Test mode. If the battery is weak, or not present, the system will reset and the console will display

“df’. To restore the system, and silence any

beeping, enter the security code and press the

OFF key.

Alann messages will be sent to the central station during the following tests 4 8 5. r”,

Notify them that tests will be in progress.

i.,,

;;

Arm the system and fault one or more zones. After 15 seconds (if optional dialer delay is selected), silence afarm sounder(s) by entering the code and pressing OFF. Check Entry/Exit delay zones.

Check the keypad-initiated alarm by pressing the

Panic key pairs - r] and [#I. If the system has been programmed for audible emergency, the console will emit a steady alarm sound, and

ALARM and 07 will be displayed. Silence the

alarm by entering the security code and

pressing OFF.

If the system has been programmed for silent

emergency, there will be no audible alarms or

displays, but a report will be sent to the central

station. Notify the central station that all tests are fin-

ished, and verify results with them.

Note: If the battery standby capacity is exceeded during an AC power failure, the 4110 will automatically shut itseff off.

Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarmsyStem.

The installer should assume the responsibility of developing and offerfng a regular maintenance program to the user as well as acquainting the user with the proper operation and limftatiins of the alarm system and its component parts. Recommendations must be included for a specific program of frequent testing (at least weekfy) to insure the system’s proper operation at all times.

ACCESSORIES

No. 1321rTFP 16.5VAC 25VA Plug-In Trans-

former (U.S.A. installations).

No. 1321CN 16.5VAC 25VA Plug-In Trans-

former (Canadian installations).

BRK PA400B

Piezoelectric Alarm Sounder, 90dB output (mounts in singlegang box).

No. 702 Self-contained 20 watt Siren

(indoor or outdoor).

No. 740 Extremely loud Piezoelectric

Alarm Sounder, 122dB output

(indoor or outdoor).

No. 411 OPRVP Programming Form (Pkg of 50)

c----l

No. 4116

Tampered Single LED Remote Station (Arming/Disarming Keyswitch). NO7E: Obtain Lo&-

switch separately (Ademo No. 2774-70. 40%70,

014005-70).

No. 1206 Battery Test Switch (N.C. Momentary)

Required for UL Installations

BRK 1412

4-wfre fonfzation Products of

Combustion Detector

BRK 2412

4-wire Photoelectric Smoke Detector

BRK 2412TH 4-wire Photoelectric Smoke

Detector w/l35OF (57%) Heat Detector

also: Nos. 4127, 4137, and 5330

(see SPECIFICATIONS on next page).

f----I

-12-

www.PDF-Zoo.com

4110 SECURfTY CONTROL

l.Physlcal: 12-l/2” (318mm)W

14-l/2” (368mm) H

3” (78mm) D

2. Electrical: VOLTAGE INPUT: 16.5VAC from plug-in 25VA

transformer, Ademco No. 1321ITF2. (in U.S.A.). Note: For Canadian installations, a’ No. 1321CN

transformer must be used.

RECHARGEABLE BACK-UP BATTERY: 12VDC

4AH (Gel type)

ALARM SOUNDER: 10.5-l 3.8V, P.OAmp output

can drive 12V BELLS or can drive one or two 702

(serles connected) self-contained 20-watt sirens. Do not connect two 702s in parallel.

AUXILIARY POWER OUTPUT: 10.5-13.8VDC, 5OOrnA max. fnterrupts for smoke detector reset.

Note : For UL installations, Alarm Sounder plus

Auxiliary Power currents should not exceed

600mA.

STANDBY TIME: 4 HRS with Auxiliary load of 5OOmA (using 4AH battery).To determine total standby battery load, add 1OOmA to total Aux. power output and remote console currents.

FUSES: Battery (3A) No. 90-12

Sounder (2A) No. 90-2 3: Communlcatlon: FORMATS SUPPORTED: Ademco Express, 10 characters/set, DTMF

(TouchTone) Data Tones, 1400/2300Ht ACK, 1400Hz KISSOFF

Ademco Low Speed, 10 pulseslsec, 1900Hz Data Tone, 1400Hz ACKMISSOFF

Radionlcs/SESCOA, 20 pulses/sec.l8OOHz Data Tone, 2300Hz ACfUKISSOFF

Can report O-9, B-F Line Seize: Double Pole Ringer Equivalence: 0.08 FCC Registration No.: AC 398U-68192-AL-E

4127 REMOTE CONSOLE

1. Physlcal: 5-518’ (143mm)W 4-11/16’ (119mm)H

718’

(22mm) D

2. Electrical: Voltage Input: 12VDC

Current Drain: 20mA

3. Interface Wlrlng:

RED:

12VDC input (+) aux pwr

GREEN:

Data Out to Control YELLOW: Data In from Control BLACK: Ground

4137 REMOTE -CONSOLE

1. Physlcal: 8-2/5’ (213mm)W 4-314’ (121 mm) H

l-1/10” (28 mm) 0

2. Electrlcal: Voltage Input: 12VDC

3. Interface

RED:

BLUE:

GREEN:

YELLOW:

BLACK:

Currht Drain: 60mA

Wiring:

12VDC input (+) aux pm 18VDC input from optional No 1350 or 1360 Power Pack Data Out to Control Data In from Control Ground and (-) connection from optional No. 1350 or 1360 Power

Pack

6330 REMOTE ALPHA CONSOLE (Seiecl Vector Device)

1. Physlcal: 7-3/4” (197mm)W 4-7116” (113mm) H

l-114’

(32mm) D

2. Electrlcal: Voftage Input: 12VDC

Current Drain: ,105mA

3. Interface Wlrlng:

RED:

12VDC inpuf (+) aux pwr

GREEN:

Data Out to Control

YELLOW: Data In from Control

BLACK:

Ground

-13-

www.PDF-Zoo.com

WARNING

THE LIMITATIONS OF ‘THIS ALARM SYSTEM

:‘g,

While this System is an advanced design security system, it does not offer guaranteed protection against burglary, fire or

other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example:

Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery-operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work ff their AC power supply is cut off for any reason, however briefly.

. A user may not be able to reach a panic or emergency button quickly enough.

While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide earfy warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal

Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires

that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed

doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Finally, smoke detectors have sensing limitations.

No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, chiklren playing with matches, or arson. Depending on the nature of the fire and/or bcation of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death.

Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes piace behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of the protected area approaches the temperature range of 90” to lSO”F, the detection performance can decrease.

Afarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers ff they are bcated on the other side of cbsed or partly open doors. tf warning devices are located on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliance, or by passing traffii. Finally, afarm warning devices, however bud, may not warn hearing-impaired people.

9 Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or

temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.

9 Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect

themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately.

‘..

This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as bng as 20 years, the electronic components could tail at any time.

The most common cause of an afarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This

alarm system should be tested weekly to make sure all sensors are working properly. The security console (and remote keypad) should be tested as well.

Installing an alarm system may make the owner eligibie for a lower insurance rate, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue

to insure their lives and property.

We continue to develop new and improved protection devices. Users of alarm systems owe it to themsefves and their loved ones to learn about these developments.

-7 !

.!1

. .

-14-

www.PDF-Zoo.com

CANADIAN DEPARTMENT OF COMMUNICATIONS

(DOC) STATEMENT

NOTICE

The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The

Department does not guarantee the equipment will operate to the user’s satisfaction.

iBefore installing this equipment, users should ensure that it is permissible to be connected to the facilities of the IloCal telecommunications company. The equipment must also be installed using an acceptable method of iconnection. In some cases, the company’s inside wiring associated with a single line individual service may be ~extended by means of certified connector assembly (telephone extension cord). The customer shouM be aware ‘that compliance with the above conditions may not prevent degradation of service in some situations.

‘Repairs io certified equipment should be made by an authorized Canadian maintenance facility designated by the 1 supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the

telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the elect&al ground Wnnections of the power utility, telephone

lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: User should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

The (LN) assigned to 8aCh t8rminal device d8nOt8S the percentage of the total load to b8

Wnn8Ct8d to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject Only to the requirement that th8 total of the Load Numbers of all the devices does not exceed 100.

AVIS

L%tiquette du ministr&e des Communications du Canada identifie le mat&f81 homologri6. Cette Btiquette Wrtiiie

‘que le materiel est conforme a cettaines normes de protection, d’exploitation et de s&urit6 des rdseaux de

t&~communications. Le minister8 n’assure toutefois pas que I8 mat&i81 fonctionnera a la satisfaction de I’utilisateur.

Avant d’installer c8 mat&iel, l’utilisateur doit S’aSSur8r qu’il eSt permis de I8 racwrder aux installations de

Pentreprise locale de t6l6wmmunication. Le matMel dolt 4galement &re install6 en suivant une method acceptde ,de raccordement. DanS CertainS cas, l8S filS iftt&ieUrS de I’8I’Itr8priS8 utilis& pour un ~8rvic8 individuel a lign8 ‘Unique p8UVent 8tr8 prOlOng& au moyen d’un diSpOSitif homologu4 d8 raCWrd8ment (cordon prolongateur lt&phOniqtJ8 iM8m8). L’abonne ne dOit pas OUbli8r qU’il8St possible que la WIIfOrmit~ aux Wndiiions

honch

Ici-dessus n’empechent pas la degradation du sefvtce par certaines situations. ACtUellem8nt, les enterprises de ~t6l4wmmunication ne permettent pas’que I’on raccorde leur mat&i81 aux jacks d’abonn~s, sauf dans l8s cas ~ precis p&us par les tarrifs patticuliars de ces entmprises.

ales reparations de mat&i81 homologue doivent &re 8ff8ch~~8s pas un centre d’entretien canadien authoris4 idesign par le fOUmiSSeUr. La wmpagnie de t~l6wmmunications p8ut demander a l’utilisateur de debrancher un iappareil a la suite de reparations ou de modifications effectu68s par l’utilisateur ou a cause de mauvais jfonctionnement.

‘Pour sa propre protection, I’utilisateur doit s’assurer que tous 18s fils de mise B la terre de la sourc8 d’energie

6lectriqu8, d8S lign8S M6phOniqU8S et des CanaliSatiOnS d’eau m&alliqU8S, S’il y en a, Wnt racWrd& ensemble.

Cette p&caution es1 particuli~rement importante dans les r4gions rurales. t Avertissement:

L’utilisateur ne doit pas tenter de fair8 ces raccordements l&m&me; il doit avoir rewurs B un

~ service d’inspection des installations 6lecttiques. ou & un &ctrician, selon le cas.

,* .

w(lC) assign4 a ChaqU8 dispositif terminal pour 6vtter toute surcharge indique le pourcentage de i la charge tOtale qui p8ut &re t’aCWtde6 a un circuit t6l6phOnique boud6 utilis6 par ce dispositif. La terminaison du Icircuit boucl6 peUt &re COnStitU68 de n’imporle quell8 WmbinaiSOn de dispositifs, pourvu que la somme des iindices de charoe de I’ensemble des dispositifs ne depasse Pas 100.

-15-

www.PDF-Zoo.com

FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. ft has been type tested and found to comply with the limits for a Class

computing device in accordance with the specifications in Part 15 of FCC Rules,

which are designed to provide reasonable protection against such interference in a residential installation. However, there is

no guarantee that interference will not occur in a particular installation. ff this equipment does cause interference to radio or

television reception, which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the foffowing measures: .

lf using an indoor antenna, have a quality outdoor antenna installed.

Reorient the receiving antenna until interference is reduced or eliminated.

Move the radii or television receiver away from the receiver/control.

Move the antenna leads away from any wire runs to the receiver/control.

Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch

circuits. If necessary, the user should consult the dealer or an experienced radionelevision technician for additional suggestions. Ths

user or installer may find the following booklet prepared by the Federal Communications Commission helpful:

‘Interference Handbook.

This booklet is available under Stock No. 004-000-00450-7 from the U.S. Government Printing Off& Washington, DC 20402.

The user shall not ma&e any changes or modifkatbns to the equipment unless authorized by the Instalktkw Instructions OI Usefs Manual. Unauthotized changes or modifkzations could void.the user’s authority to operate the equloment.

ADEMCO LIMITED WARRANTY

Alarrn Device Manufacturing Company, a Division

of Piiay Corporation, and its divisions, subsidiaries and affili-

ates (‘Sellef),

165 Eileen Way, Syosset, New York 11791,

warrants its

products to be in conformance with its own

plans and specifications and to be free from defects in materials and workmanship under normal, use and senrice for 16 months from the date stamp wntrol on the product or, for products not having an Ad8mW date stamp, for

12 months from date of original pUChaS8 unless th8 iWtallatiOn iWtNCtiOnS or Wtakig Sets forth a Shorter period,

in which case the shorter period shall apply. Seller’s obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product which is proved not in compliance with Sellers specifiions or prOV8S d8f8ChV8 in materials or workmanship under normal use and service. Selier shall have no obligation under this Limited Warranty or otherwise if the product is altered or improp8rly repaired or serviced by anyone other than Ad8mW factory service. For warranty service, return product transportation prepaid, to Ademco Factory Service, 165 Eileen Way, Syosset, New York 11791.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A

PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE

HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL

DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY. EXPRESS OR IMPLIED. OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLERS OWN NEGUGENCE OR

FAULT.

Seller do8S not represent that the pIoduCtS tt Sells may not be WmprOr’niWd Or circumvented: that the prOdUCtS will prevent any personal injury or property bss by burglary, robbery, fire or otherwise; or that the products will in all cases provide adequate warning or protection. Customer Und8rStandS that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fir8 or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result.

CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER’S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER.

This

warranty replaces any previous warranties

and is the only warranty made by Seller on this product. No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized.

‘%DEMCOj

ALARM DEVlCE MANUFACTURING CD-

UUSlCPJ OF

UKWAY

COFPCRATfoN

165 Eileen Way, Syosset, New York 11791

Cowrioht 01000 PITWAY COWORAllON

N4926V5 4/92

www.PDF-Zoo.com

ADEMCO 4110 Installation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual