Adder Technology DDC Ghost User Manual

Safety information

D

D

C

G

h

o

st

V

G

A

S

T

AT

U

S

C

L

O

N

E

COMPUTER

MONIT

OR

D

D

C

G

h

o

s

t

V

G

A

S

T

AT

U

S

C

L

O

N

E

COMPUTER

M

ONIT

OR

EDID

data

V

ideo

signals

Black connector
(to monitor)

Blue connector
(to computer)

Optional
power
input

Control button
and indicator

• For use in dry, oil free indoor environments.

• Not suitable for use in hazardous or
explosive environments or next to highly
flammable materials.

• Warning – the optional power adapter
contains live parts.

• No user serviceable parts are contained
within the module or the power adapter

- do not dismantle.

• Do not use the power adapter if the
power adapter case becomes damaged,
cracked or broken or if you suspect that it
is not operating properly.

• Replace the power adapter with a
manufacturer approved type only.

• If you use a power extension cable with
the optional power adapter, make sure the
total ampere rating of the devices plugged
into the extension cable do not exceed
either the cable’s ampere rating or that of
the wall outlet.

FCC statement

This equipment generates, uses and can radiate
radio frequency energy and if not installed and
used properly, that is, in strict accordance with the
manufacturer’s instructions, may cause interference to
radio communications. It has been tested and found to
comply with the limits for a Class A computing device in
accordance with the specifications in Subpart J of part 15
of FCC rules, which are designed to provide reasonable
protection such interference when the equipment is
operated in a commercial environment. Operation of this
equipment in a residential area may cause interference, in
which case the user at his own expense will be required
to take whatever measures may be necessary to correct
the interference. Changes or modifications not expressly
approved by the manufacturer could void the user’s
authority to operate the equipment.

Warranty

Adder Technology Ltd warrants that this
product shall be free from defects in
workmanship and materials for a period of
two years from the date of original purchase.
If the product should fail to operate correctly
in normal use during the warranty period,
Adder will replace or repair it free of charge.
No liability can be accepted for damage due
to misuse or circumstances outside Adder’s
control. Also Adder will not be responsible
for any loss, damage or injury arising directly
or indirectly from the use of this product.
Adder’s total liability under the terms of this
warranty shall in all circumstances be limited
to the replacement value of this product. If
any difficulty is experienced in the installation
or use of this product that you are unable to
resolve, please contact your supplier.

European EMC directive
89/336/EEC

This equipment has been tested and found to
comply with the limits for a class B computing
device in accordance with the specifications

in the European standard EN55022. These
limits are designed to provide reasonable protection against
harmful interference. This equipment generates, uses and
can radiate radio frequency energy and if not installed and
used in accordance with the instructions may cause harmful
interference to radio or television reception. However, there
is no guarantee that harmful interference will not occur
in a particular installation. If this equipment does cause
interference to radio or television reception, which can
be determined by turning the equipment on and off, the
user is encouraged to correct the interference with one or
more of the following measures: (a) Reorient or relocate
the receiving antenna. (b) Increase the separation between
the equipment and the receiver. (c) Connect the equipment
to an outlet on a circuit different from that to which
the receiver is connected. (d) Consult the supplier or an
experienced radio/TV technician for help.

DDC Ghost

User Guide

The DDC Ghost module is designed to
attach in-line with a VGA connection
in order to present Extended Display
Identification Data (EDID) to the video
controller independently of the actual
monitor, switch or extender unit. Video
signals are passed straight through the
DDC Ghost.

The Extended Display Identification Data
(EDID) information stored within the DDC
Ghost can either be cloned from a monitor
or used with a standard set of information
(see Standard EDID Information).

What’s in the box

DDC Ghost module

Adder Technology Limited,
Technology House,
Trafalgar Way, Bar Hill,
Cambridge, CB3 8SQ,
United Kingdom
Tel: [phone]
Fax: [phone]

© 2008 Adder Technology Limited • Release 1.0e • January 2008 • Part No. ADD0074
All trademarks are acknowledged. Documentation by Corporate Text & Design (www.ctxd.com)

Email: [e-mail] Web: www.adder.com

Adder Corporation,
29 Water Street,
Newburyport, MA 01950,
United States of America

Tel: [phone]
Fax: [phone]

Adder Asia Pacific
6 New Industrial Road,
Hoe Huat Industrial Building
#07-01, Singapore 536199

Tel: [phone]
Fax: [phone]

Video cable
(15 pin D-type male
to 15 pin D-type
male)

What you may additionally need

Mains to 5VDC power adapter (if power cannot be obtained
from the controlling computer via the video cable) Adder P/N: PSU-IEC-5VDC

Additional video cable (15 pin D-type male to 15 pin D-type male) Adder P/N: VSC18

DDC

Ghost

VGA

S

T

AT

U

S

C

L

O

N

E

C

O

M

P

U

T

E

R

M

O

N

IT

O

R

Cloning EDID information

D

D

C

G

h

o

s

t

V

G

A

S

T

AT

U

S

C

L

O

N

E

CO

M

PUTER

MONIT

OR

D

D

C

G

h

o

s

t V

G

A

S

T

AT

U

S

C

L

O

N

E

COMPUTER

MO

NIT

OR

D

D

C

G

h

o

s

t

V

G

A

S

T

AT

U

S

C

L

O

N

E

COMPUTER

MONI

T

OR

The DDC Ghost module contains a default set of EDID values which
may be used immediately with most monitors (see Standard EDID
Information). Alternatively, you can use a ‘donor’ monitor from which
you can clone new EDID information.

To clone EDID information

1 Link the BLACK connector of the DDC Ghost to the donor monitor

(diagram A).

2 Provide power for the DDC Ghost module in one of two ways, either:

• Link the BLUE connector of the DDC Ghost to a computer video
output for the duration of the cloning operation (diagram B), or

• Attach the optional 5VDC power adapter to the socket on the side
of the DDC Ghost module (diagram C).

3 Ensure that the donor monitor and the DDC Ghost module are

powered. The DDC Ghost red STATUS indicator should be on.

4 Using a narrow implement, press and hold the recessed button

labelled CLONE on the side of the module (diagram D). The STATUS
indicator will begin to flash slowly for five seconds. Release the
button while the indicator is still slowly flashing.

• If new EDID information is available, it will be copied to the DDC
Ghost module memory.

• If there is no EDID information to clone then the existing DDC
Ghost memory will be not altered.

• If there is an error during cloning then the DDC Ghost will be
automatically reset to its standard values.

5 When the operation is complete, the STATUS indicator will flash

rapidly five times. Disconnect the DDC Ghost module from the donor
monitor.

Resetting EDID information

If required, you can reinstate the standard EDID values (see Standard
EDID Information) into the DDC Ghost module memory.

To reset the EDID information

1 Ensure that the DDC Ghost is powered (either from the video output

of a host computer or an optional power adapter) and check that the
red STATUS indicator is on.

2 Using a narrow implement, press and hold the recessed button

3 Release the button while the red STATUS indicator is off, following

labelled CLONE on the side of the module (diagram D). The red
STATUS indicator will flash slowly for five seconds and then will go
off for a further five seconds.

the five slow flashes. The reset operation will take place and then
the red STATUS indicator will flash rapidly five times to indicate a
successful completion.

A

Link the monitor
to the BLACK
connector

B

C

D

Link the computer
to the BLUE
connector

If power is
unavailable from
the computer via the
BLUE connector, use
the optional 5VDC
power adapter

Press and hold the
recessed CLONE button.
Release it as follows:

To clone: While
indicator is slowly
flashing.

To reset: While
indicator is off
(immediately following
the slow flashes).

Installing for normal operation

During normal operation, the DDC Ghost module supplies either
standardised or cloned EDID information to the computer instead of
the data from the connected monitor.

To install for normal operation

1 Link the BLACK connector of the DDC Ghost to the monitor

(diagram A).

2 Link the BLUE connector of the DDC Ghost to the computer

video output (diagram B)

Note: In operation, the red STATUS indicator should be on. If

it is not then power is not being correctly supplied from the
computer (pin 9 of the VGA connector). If this situation cannot
be resolved, attach the optional 5VDC power adapter to the
socket on the side of the DDC Ghost module (diagram C).

3 Switch on the computer and monitor in the normal manner.

Standard EDID information

The standard EDID information supplied within the DDC
Ghost module represents a standard analogue monitor
(with no manufacturer details) capable of resolutions up to
1600x1200@60Hz. Other presented information is as follows:

Manufacturer details

ID Manufacturer Name: NON

Product ID Code: 0000
Last 5 Digits of Serial Number: 00000
Week of Manufacture: 00
Year of Manufacture: 1990
Complete Serial Number: 0000000000

Video input definition

Analog Signal: 0.700, 0.300 (1.000 Vp-p)

Separate Syncs

Established timing I

720 X 400 @ 70Hz (IBM,VGA)

640 X 480 @ 60Hz (IBM,VGA)
640 X 480 @ 75Hz (VESA)
800 X 600 @ 60Hz (VESA)

Established timing II

800 X 600 @ 75Hz (VESA)

1024 X 768 @ 60Hz (VESA)
1024 X 768 @ 75Hz (VESA)
1280 X 1024 @ 75Hz (VESA)

Standard timing identification

1280 X 1024 @60Hz

1600 X 1200 @60Hz
1152 X 864 @75Hz

Note: The DDC
Ghost module has
the capacity to store
one standard EDID
data block plus one
extension block.