Adder Technology AV4OSD User Manual

ADDER

VViieeww

OSD

ADDER

VViieeww

OSD

www.addertec.com

8 Port ADDER View OSD

AV8OSD

AV4OSD

RC1

4 Port ADDER View OSD

Remote Control Pad/Display

About this manual

All rights reserved. Whilst every precaution has been taken in the preparation of this manual, Adder Technology Ltd assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. We reserve the right to change the specifications, functions and circuitry of the product without notice. All trademarks acknowledged.

Safety information

For use in dry, oil free indoor environments only. Warning - live parts contained within power adapter. No user serviceable parts within power adapter - do not dismantle. Plug the optional power adapter into a socket outlet close to the AdderView. Replace the power adapter with a manufacturer approved type only. Do not use power adapter if power adapter case becomes damaged, cracked or

broken or if you suspect that it is not operating properly.

Warranty

Adder Technology Ltd warrants that this product shall be free from defects in workmanship and materials for a period of two years from the date of original purchase. If the product should fail to operate correctly in normal use during the warranty period, Adder will replace or repair it free of charge. No liability can be accepted for damage due to misuse or circumstances outside Adder’s control. Also Adder will not be responsible for any loss, damage or injury arising directly or indirectly from the use of this product. Adder’s total liability under the terms of this warranty shall in all circumstances be limited to the replacement value of this product.

If any difficulty is experienced in the installation or use of this product that you are unable to resolve, please contact your supplier.

AdderView OSD Installation and Use Page 1

Radio Frequency Energy

Shielded cables must be used with this equipment to maintain compliance with radio frequency energy emission regulations and ensure a suitably high level of immunity to electromagnetic disturbances.

European EMC directive 89/336/EEC

This equipment has been tested and found to comply with the limits for a class B computing device in accordance with the specifications in the European standard EN55022. These limits are designed to provide reasonable protection against harmful interference. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception. However, there is no guarantee that harmful interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to correct the interference with one or more of the following measures: (a) Reorient or relocate the receiving antenna. (b) Increase the separation between the equipment and the receiver. (c) Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. (d) Consult the supplier or an experienced radio / TV technician for help.

FCC Compliance Statement (United States)

This equipment generates, uses and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to comply with the limits for a class A computing device in accordance with the specifications in Subpart J of part 15 of FCC rules, which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment. Operation of this equipment in a residential area may cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Canadian Department of Communications RFI statement

This equipment does not exceed the class A limits for radio noise emissions from digital apparatus set out in the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le règlement sur le brouillage radioélectriques publié par le ministère des Communications du Canada.

AdderView OSD Installation and Use Page 2

Contents

1. Introduction....................................................................................5

1.1 Key features...........................................................................................5

1.2 Package contents (models AV4osd and AV8osd) .................................6

1.3 Rack mount kit contents (part code: AVrmk)..........................................6

1.4 Remote controller contents (part code: AVremote)................................6

1.5 Product information ...............................................................................7

2. Installation...................................................................................... 9

2.1 What you will need ................................................................................9

2.2 Mounting the AdderView .......................................................................10

2.3 Connecting your devices .......................................................................10

2.4 ‘Interface powered’ operation without the optional power adapter ........11

2.5 Configuring your PCs ............................................................................11

2.6 Configuring the AdderView ...................................................................11

2.7 Summary of AdderView configuration options ...................................... 12

2.8 Other useful installation information ......................................................14

2.9 Re-enabling a disconnected PS/2 mouse ............................................. 15

2.10 Hot plugging the AdderView into running systems and re-enabling

disconnected PS/2 CPU mouse connections .............................................. 15

3. Using the AdderView .................................................................... 18

3.1 Power on status ..................................................................................... 18

3.2 Front panel keys and remote controller.................................................. 19

3.3 Status display......................................................................................... 19

3.4 Keyboard hotkey control ........................................................................ 20

3.5 On-screen menu control.........................................................................22

3.6 Mouse control.........................................................................................24

3.7 RS232 control ........................................................................................ 24

3.8 Cascading AdderViews .........................................................................24

AdderView Installation and Use Page 3

4. AdderView configuration options................................................ 26

4.1 Screen saver time delay ........................................................................26

4.2 Autoscan lock on mode and delay time ................................................26

4.3 Mouse mode and mouse switching of channels ....................................27

4.4 Keyboard hotkey combination ...............................................................28

4.5 Firmware functions (version query, mouse restore and reset) ..............29

4.6 Display appearance options ..................................................................29

4.7 Setting a security password ..................................................................30

4.8 Cascade query code .............................................................................31

4.9 Exit configure mode .............................................................................. 31

Appendices

A - Cable and connector specifications................................................................32

B - Problem solving ..............................................................................................34

AdderView Installation and Use Page 4

1. Introduction

Thank you for purchasing the AdderView OSD. Your AdderView is a high performance keyboard, monitor and mouse sharing device which supports a wide range of PC hardware and software platforms.

1.1 Key features

Control multiple PCs from a single keyboard, monitor and mouse. On-screen menu allows computers to be selected by name. SmartBoot feature automatically boots all machines during power up. ‘Interface powered” operation – AdderView draws its power from the connected

PCs. Mixed AT/PS2 keyboards and PS2/RS232 mice supported as standard. Can be cascaded to provide a video switching network. Password security prevents unauthorised use. Remote control module for convenient operation. Channel switching by on-screen display, front panel key, keyboard hotkey, or 3

button mouse. Automatically restores keyboard and mouse states when channel changed. Can be controlled remotely via an RS232 serial port. Supports high bandwidth monitors at resolutions up to 1900 x 1200. Supports keyboard modes 1,2 and 3 and mouse prompt and stream modes for

maximum compatibility. Includes screen saver, auto-scan and variable hotkey options. Confirmation of selected ports on local and cascaded AdderViews. Supports Microsoft IntelliMouse and other common wheel mice. Mouse restoration functions to enable ‘hot plugging’ of certain systems.

AdderView Installation and Use Page 5

Supports IBM ThinkPad ‘Y’ cables. Power and activity indication confirm correct operation. Standard cable connections make installation easy and inexpensive. All ports are active simultaneously – all PCs may all be booted at the same time. Robust metal case ensures good shielding and video quality. 19 inch rack mount kit available.

Supports RS6000 computers. Optional power adapter can be used for ‘video only’ or cascade applications.

1.2 Package contents (models AV4osd and AV8osd)

AdderView OSD. 4 x stick on self-adhesive rubber feet. This installation guide. (Please note that a power adapter is NOT required for most applications and so is

not included. This may be purchased separately if required).

1.3 Rack mount kit contents (part code: AVrmk)

2 x mounting brackets for fixing the unit into a 19 inch rack. 4 x screws for fixing mounting brackets to the AdderView OSD.

1.4 Remote controller contents (part code: AVremote)

Remote control module. Velcro strip for mounting remote controller.

AdderView Installation and Use Page 6

1.5 Product information

Fig. 1 – AdderView OSD (model AV8osd)

Fig. 2 - Remote control pad / display (optional accessory) Part code: AVremote

AdderView Installation and Use Page 7

Fig. 3 – AdderView OSD (model AV4osd)

AdderView Installation and Use Page 8

2. Installation

2.1 What you will need

Cables to connect the AdderView to each of your PC keyboard, video and mouse

ports. Cable specifications are given in appendix A. (You do not need to connect a mouse cable if you are not using the mouse).

A monitor with a standard VGA/SVGA (15 pin) connector that will work when

connected directly to each of your PCs. AdderView supports low and high resolution monitors.

A standard AT or PS/2 style keyboard. If you are using an AT keyboard with a 5

pin connector you may connect this to the AdderView using a standard AT to PS/2 keyboard adapter.

A PS/2 style two or three button Microsoft or Logitech compatible mouse or a

Microsoft IntelliMouse compatible mouse. If you wish to use the mouse to switch the AdderView's channel then you will need a three button mouse or an IntelliMouse.

(The AdderView supports ‘Internet Mice’ that are compatible with the Microsoft

IntelliMouse. These are fitted with a wheel or other scroll control and sometimes have additional buttons. Examples are: Microsoft IntelliMouse, Logitech Pilot Mouse+, Logitech MouseMan+, Genius NetMouse and Genius NetMouse Pro.)

A suitable mouse driver for your PCs. Supported types are:

- PS/2 or RS232 two button mouse driver (any manufacturer).

- Microsoft mouse driver (including IntelliMouse).

- Logitech mouse driver (including two button, three button and wheel mouse)

Use of PS/2 and RS232 style mice with the AdderView - All of the mouse connections from AdderView to PCs support either a PS/2 or an RS232 mouse. AdderView automatically converts from the PS/2 mouse commands to RS232 serial mouse commands. Serial mice types are selected by using an adapter as described in Appendix A. The AdderView will operate without a mouse connected if you do not wish to use one.

AdderView Installation and Use Page 9

2.2 Mounting the AdderView

The AdderView has been designed to be used either on a desktop or mounted in a 19 inch rack. If the AdderView is to be used on a desktop then you will need to stick the supplied self-adhesive rubber feet to the underside of the AdderView. If the AdderView is to be mounted in a 19 inch rack then you will need to fit the rack mounting brackets to the side of the AdderView. The 19 inch rack mounting brackets are supplied in the option rack mounting kit (part code: AVrmk)

2.3 Connecting your devices

Ensure that the optional power adapter is disconnected from the AdderView and that all the devices which are to be attached are switch off. Connect the shared keyboard, PS/2 mouse and monitor to the connectors at the rear of the AdderView (see figs 1, 2 and 3). Connect your keyboard monitor and mouse to the control port. Next connect each computer system unit in turn with the keyboard cable, mouse cable and video cable. Any unused computer connections can be left unconnected. To connect computers with serial mouse connections and AT style keyboard connections use the adapters supplied in the cabling pack as shown below. Alternatively, if you have chosen not to purchase the cable pack, refer to appendix A for cable specifications.

The AdderView is now ready for use and will start to operate as soon as one of the attached PCs is powered on. If you are connecting to PCs using cables that are longer than 3 metres or are cascading the AdderView to another AdderView you will need to use the optional power adapter. When using the optional power adapter, ensure that it is connected to the mains and powering the AdderView before you switch on the connected computers. Failure to switch the AdderView and computers on in the correct order can lead to the mouse and/or keyboard not being recognised

AdderView Installation and Use Page 10

by the computers when they are switched on.

2.4 ‘Interface powered’ operation without the optional power adapter

The AdderView draws its power from the connected computers via the keyboard cables. A single keyboard connection is normally sufficient to power the AdderView provided that the cable is no longer than 3 metres. If more than one computer is connected then the power will be intelligently drawn from all computers. Cables longer than 3 metres may be used provided that the AdderView is already powered by another connected computer or the optional power adapter. If you are cascading the AdderView to another AdderView then a power adapter must be connected to all AdderViews.

2.5 Configuring your PCs

Configure your PC in the same way that you would if your keyboard, mouse and monitor were all connected directly to your PC, but bearing in mind the following points:

AdderView emulates Microsoft compatible serial, IntelliMouse and PS/2 mice, so

ensure that your PC software is configured for a Microsoft mouse of the correct type. Refer to the list of supported drivers in section 2.1.

AdderView supports VGA/SVGA/XGA/XGA2 type monitors, but does not support

the automatic detection features available with some ‘plug and play’ monitors and video cards. If you have this type of video card and monitor, you should select the video mode manually instead of relying upon the automatic detection feature.

2.6 Configuring the AdderView

The AdderView is supplied pre-configured with factory defaults which are suitable for most applications. There are a number of more advanced options which can be set by the user. These are stored in the AdderView's EEPROM memory and are retained when the power is disconnected.

AdderView Installation and Use Page 11

+ 27 hidden pages

Adder Technology AV4OSD User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual