ADC S2785 011, S2790 011, S2783 011 Users Manual

ADC Spectrum 7.0

Installation Guide

D-xxxxxx-x-xx Rev A

ADCP-77-xxx  Issue 1  12/2009

ADC Telecommunications, Inc. P.O. Box 1101, Minneapolis, Minnesota 55440-1101 In U.S.A. and Canada: 1-800-366-3891 Outside U.S.A. and Canada: (952) 938-8080 Fax: (952) 917-1717

shall not be modified, used, copied, reproduced or disclosed in whole or in part without the written consent of ADC.

Trademark Information

ADC is a registered trademark and FlexWave and Universal Radio Head are tradema rks of ADC Telecommunications, Inc. No right, license, or interest to such trademarks is granted hereunder, and you agree that no such right, license, or interest shall be asserted by you with respect to such trademark.

Other product names mentioned in this practice are used for identification purposes only and may be trademarks or registered trademarks of their respective companies.

Disclaimer of Liability

Contents herein are current as of the date of publication. ADC reserves the right to change the contents without prior notice. Should the content of printed user documentation shipped with product differ from documentation provided on a product CD (inclusive of the associated Help modules), the printed user documentation supersedes the documentation on the product CD. In no event shall ADC be liable for any damages resulting from loss of data, loss of use, or loss of profits, and ADC further disclaims any and all liability for indirect, incidental, special, consequential or other similar damages. This disclaimer of liability applies to all products, publications and services during and after the warranty period.

Specific Disclaimer for High-Risk Activities

This Product is not specifically designed, manufactured, tested or intended for use in high-risk activities including, without restricting the generality of the foregoing, on-line control of aircraft, air traffic, aircraft navigation or aircraft communications; or in the design, construction, operation or maintenance of any nuclear facility. ADC (including its affiliates) and its suppliers specifically disclaim any express or implied warranty of fitness for such purposes or any other purposes.

Screenshots in User Documentation

Due to concurrent development of this documentation, artwork, and the FlexWave URH EMS product, there may be some minor discrepancies between screenshots contained in this documentation and those actually displayed in the FlexWave URH EMS. These discrepancies wil l generally be few and minor and should not affect your understanding of FlexWave URH EMS.

TABLE OF CONTENTS

Preface.................................................................................................................... 2

Revision History................................................................................................... 2

Document Cautions and Notes...............................................................................2

General Safety Precautions ......................................................... .......................... 2

Standards Certification ........................... .............................................................. 3

Introduction............................................................................................................. 4

Host Unit............................................................................................................5

DART Remote Unit ............................................................................................... 6

IF Expansion Unit..................... ............................................................................ 7

Main Remote Access Unit...................................................................................... 8

Secondary Remote Access Unit..............................................................................9

Omni Antenna................................................................................................... 10

Installation ............................................................................................................ 11

Cascading.............................................................................................................. 14

Specifications......................................................................................................... 15

Contacting ADC...................................................................................................... 17

Preface

PREFACE

This manual provides basic installation instructions for a ADC® Spectrum 7.0 system.

Revision History

Initial release.

Document Cautions and Notes

Two types of messages, identified below, appear in the text:

CAUTION! Caution text indicates operations or steps that could cause personal injury, induce a

safety problem in a managed device, destroy or corrupt information, or interrupt or stop services.

NOTE: Note text contains information about special circumstances.

General Safety Precautions

CAUTION! Wet conditions increase the potential for receiving an electrical shock when installing or

using electrically-powered equipment. To prevent electrical shock, never install or use electrical equipment in a wet location or during a lightning storm.

CAUTION! This equipment uses a Class 1 Laser according to FDA/CDRH rules. Laser radiation can

seriously damage the retina of the eye. Do not look into the ends of any optical fiber. Do not look directly into the optical transceiver of any digital unit or exposure to laser radiation may result. An optical power meter should be used to verify active fibers. A protective cap or hood MUST be immediately placed over any radiating transceiver or optical fiber connector to avoid the potential of dangerous amounts of radiation exposure. This practice also prevents dirt particles from entering the adapter or connector.

CAUTION! This system is an RF Transmitter and continuously emits RF energy. Maintain 3 foot (91.4

cm) minimum clearance from the antenna while the system is operating. Wherever possible, shut down the RAN before servicing the antenna.

CAUTION! Always allow sufficient fiber length to permit routing of patch cords and pigtails without

severe bends. Fiber optic patch cords or pigtails may be permanently damaged if bent or curved to a radius of less than 2 inches (5.1 cm).

CAUTION! Exterior surfaces of the Remote may be hot. Use caution during servicing.

Page 2 FlexWave Prism Remote Unit Ins tallation Guide

2009 ADC Telecommunications, Inc ADCP-77-072 • Issue 2 • 11/2009

Standards Certification

FCC: This equipment complies with the applicable sections of Title 47 CFR Part 15

(Host unit), Part 22 (800 MHz Cellular), Part 24 (1900 MHz - PCS), Part 90

(800/900 - SMR), and Part 27 (700 MHz, 2100 MHz - AWS).

IC: This equipment complies with the applicable sections of RSS-131. The term

“IC:” before the radio certification number only signifies that Industry Canada

Technical Specifications were met.

The Manufacturer's rated output power of this equipment is for single carrier

operation. For situations when multiple carrier signals are present, the rating

would have to be reduced by 3.5 dB, especially where the output signal is

re-radiated and can cause interference to adjacent band users. This power

reduction is to be by means of input power or gain reduction and not by an

attenuator at the output of the device.

NOTE: To comply with Maximum Permissible Exposure (MPE) requirements, the maximum

composite output from the antenna cannot exceed 1000 Watts ERP (Cellular and SMR), the antenna cannot exceed 1640 Watts EIRP (PCS), and the antenna must be permanently installed in a fixed location that provides at least 6 meters (20 feet) of separation from all persons.

Preface

NOTE: The U.S. Federal Communications Commission (FCC) has developed guidelines for

evaluation of human exposure to RF emissions. The guidelines incorporate limits for Maximum Permissible Exposure (MPE) for power density of transmitter operating at frequencies between 300 kHz and 100 GHz. Limits have been set for portable, mobile, and fixed equipment. ADC products fall in the category of fixed equipment; products intended to be permanently secured and exposures are evaluated for distances greater than 20cm (7-7/8”). Portable devices fall into exposures of less than 20cm, where SAR evaluations are used.

Antenna gain is restricted to 1.5 W ERP (2.49 W EIRP) in order to satisfy RF exposure compliance requirements. If higher than 1.5 W ERP, routine MPE evaluation is needed. The antennas should be installed to provide at least 20cm from all persons to satisfy MPE requirements of FCC Part 2, 2.1091.

UL/CUL: This will be installed in a restricted access location. This equipment

complies, per UL and CUL 50, Standard for Enclosures for Electrical Equipment.

FDA/CDRH: This equipment uses a Class 1 LASER according to FDA/CDRH Rules.

This product conforms to all applicable standards of 21 CFR Part 1040.

Caution: Modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Introduction

INTRODUCTION

InterReach Spectrum is an addition to the InterReach family of Distributed Antenna Systems. It offers a flexible multi-operator/multi-protocol single platform system supporting up to 8 Radio Frequency (RF) bands.

InterReach Spectrum has a Host Unit, an Expansion Unit (comprised of a DART Remote Module (DRU), IF Expansion Module (IFEU), and Power Supply), and Remote Amplifiers Units (RAUs). The Host, DRU and IFEU are intended for telecom closet indoor use. The RAU is intended to be installed above a false ceiling in an environmentally controlled office.

The standard configuration is:

• one Host Unit

• up to sixteen Expansion Units

• with each IFEU in the Expansion Unit supporting up to eight Main RAUs (one

per IFEU FWD/REV F connector paired ports).

Page 4 FlexWave Prism Remote Unit Ins tallation Guide

2009 ADC Telecommunications, Inc ADCP-77-072 • Issue 2 • 11/2009

+ 14 hidden pages