Adams Rite 7800-605, 7800-606, 7800-613E, 7800-628E, 7800-629 Installation Instructions

Diagram 8

Dimensions

NOTE: May not be to scale. For easy installation,

the HES 9000-MTK should be ordered.

1-3/4"

[44.5mm]

HES® 9800 | Adams Rite® 7800
Electric Strike

HES

9000-ASB

(optional)

Diagram 9

Set Screw

Location

Mounting

Screw

Lockdown

Screw

(optional)

Set Screw

Location

Mounting

Screw

1/2"
[12.7mm]
Clearance

10-24 UNC Screw (optional)

for

LBM/LBSM

Final Lockdown Feature 10-32 UNF or

1-5/16"

[33.3mm]

1-5/16"

[33.3mm]

Wiring

1-1/16"

[27mm]

4-1/8"

[104.8mm]

This edge

toward

door

Centerline

of Latchbolt

Installation Instructions and Frame Preparation

Product Components

A HES 9800 | Adams Rite 7800 Strike Body

B HES 9800 | Adams Rite 7800 Cover

C 1/4"-20 x 1" Mounting Screws

D #10-32 & 10-24 Lockdown Screws (optional)

E #6-32 x 1/4" Cover Screws

F 5/64" Hex Key

G 12-Volt and 24-Volt Pigtails

H 1/8" and 1/16" Spacers

Diagram 1: Product Components

A

Electrical Specifications

Electrical Ratings for Solenoid

Voltage 12 V DC 24 VDC

Resistance in Ohms 24 96

B

HES

9000-ASB

(optional)

Mounted on Aluminum Frame

with HES 9000-ASB

[e-mail] | assaabloyesh.com

800.626.7590 | 10027 S. 51st Street Phoenix, AZ 85044 USA

Mounted on

Hollow Metal Frame

9"

[228.6mm]

3/4"

[19mm]

Clearance

for Power

Wiring

2X

Mounting

Hole

Locations

for

1/4-20 UNC

Mounting

Screws

7/8"

4X

[22.5mm]

3026006.005_1
Copyright © 2018, Hanchett Entry Systems, Inc., an ASSA ABLOY Group
compan y. All rights r eserve d. Reproduc tion in who le or in part w ithout th e
expr ess writ ten permis sion of Hanche tt Entr y Systems, I nc. is prohibi ted.

4-1/8"

[104.8mm]

mA Continuous Duty 450 250

Solenoids are rated at +/- 10% indicated value.

Minimum Wire Gauge

Solenoid Voltage

Requirements

(Based on Round Trip)

200 feet or less 18 gaug e 22 gauge

200 – 300 feet 16 gau ge 22 gauge

300 – 400 feet 16 gau ge 20 gauge

UL1034

• Static Strength: 1500 lbs

• Dynamic Streng th: 70 f t – lbs

• Endurance: 250,000 cycles

UL294 Performance Levels

• Destructive Attack: Level I

• Line Security: Level I

• Endurance: Level IV

• Standby Power: Level I

NOTE: Installation wiring for the product and
wiring methods shall be in accordance with the
National Electrical Code, ANSI/NFPA70

12 V DC 24 VDC

G

C

F

H

D

E

14

CAUTION Before connecting any device at the installation site, verify input voltage using a multimeter.

Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage
exceeding 10% of the solenoid rating may cause severe damage to the unit and will void the warranty.

Preparing the Strike

For 12 VDC, the Plug In Connector (pigtail)
marked “12 VDC” should be used; for 24 VDC,
the pigtail marked “24 VDC” should be used.

Diagram 1: 12V to 24V Conversion

Diagram 2: If Connector Is Missing

• SELECT the appropriate pigtail that
matches system power and electrically
CONNECT as illustrated in Diagram 1.

• IF no connector is present,
THEN CONFIGURE the wires
as shown in Diagram 2.

or

• IF using the Latchbolt Monitor (LBM)
or Latchbolt Strike Monitor (LBSM),
THEN REFER to Diagrams 5 and 6 to
complete wiring (see page 3).

Verifying the Operation Mode

The HES 9800 | Adams Rite 7800
Electric Strike is pre-set for FAIL SECURE
OPERATION as shown in Diagram 3.

• VERIFY that both keepers are in

Diagram 3: Fail Secure Operation

FAIL SECURE OPERATION.

Converting the Operation Mode

There are two Selector Stop Pins, one on the left
side and one on the right side. Both Selector Stop
Pins must be repositioned (as shown in Diagram

4) to convert the strike to FAIL SAFE OPERATION.

IN FAIL SAFE OPERATION: Both keepers
should be unlocked without power but
locked when power is applied.

• To convert to FAIL SAFE OPERATION,
REMOVE the Selector Stop Pins on
each side of the strike body using
the provided 5/64" hex key.

• MOVE the Selector Stop Pins to the FAIL
SAFE OPERATION position (towards the
center of the strike) as shown in Diagram 4.

• TIGHTEN both Selector Stop Pins after
they have been moved to the FAIL SAFE
OPERATION position using the 5/64” hex key.

FAIL SAFE OPERATION mode should not be used
in fire rated or windstorm-resistant applications.

Diagram 4: Fail Safe Operation

Selector Stop

Pin Location

Selector Stop

Pin Location

Strike

Electric

Red/green

Strike

Electric

Red/green

Red

Violet

Black

Red

Violet

Black

Connect
Together

(+ 12 VDC)

(- NEG)

Connect
Together

(+ 24 VDC)

Connect
Together

(- NEG)

Preparing the Frame

When mounting on an aluminum frame, with a
blade stop, an HES 9000-ASB (sold separately) is
necessary to provide a secure installation. The HES
9000-ASB is shown installed in Diagrams 8 and 9.

• IDENTIFY and MARK the latchbolt
centerline on the frame.

• Using the dimensions provided on page
4, MARK all appropriate holes. If using a
HES 9000-ASB, reference the installation
instructions provided with that product.
NOTE: This may require the exit device to shift
horizontally towards the hinge side of the
door to compensate for the HES 9000-ASB.

• PUNCH, DRILL and TAP the
marked holes as required.

Finishing the Installation

• ELECTRICALLY CONNECT the HES 9800 |
Adams Rite 7800 to the Plug In Connector, and
ATTACH the electric strike to the jamb using
the 1/4"-20 x 1" mounting screws provided.

• CHECK the starwheel interaction with the
keepers to ensure proper engagement
and clearance. The starwheel’s latchguard
needs to be centered within the keepers as
seen in Diagram 7. If horizontal adjustment
is needed, use one or both of the spacers
to provide latch guard/keeper clearance.
Additional spacers can be ordered separately.

Adjusting Horizontal and Lockdown

• TIGHTEN the two 1/4"-20 x 1" mounting screws.

• SECURE the adjustment by tightening the
set screws. Shown in Diagram 8 on page 4.

• OPTIONAL LOCKDOWN FEATURE: INSTALL
the #10-24 UNC or 10-32 UNF lockdown
screw if additional security is required;
however, REMOVE the strike before drilling
hole. If using a HES 9000-ASB it will require
drilling and tapping of the lockdown hole.

• INSTALL the cover plate, and SECURE in
place using the #6-32 x 1/4" Cover Screws
as illustrated in Diagram 9 on page 4.

Diagram 5

Latchbolt Monitor

White Common
Orange Normally Open
Green Normally Closed

Diagram 6

Latchbolt Strike Monitor

Brown Common
Blue Normally Open
Yellow Normally Closed

White

Orange

Green

Brown

Blue

Yellow

Diagram 7: Starwheel & Keeper Cross-section

Latchguard should be centered between the keepers.

HES

9000-ASB

(optional)

Starwheel

Keepers

Latchuard

32