Adams Rite 4590-01-00-313, 4590-01-00-335, 4590-01-00-628, 4590-01-01-313, 4590-01-01-335 Installation Instructions

STEP 1

+1/32

.265 DIA

-0
+0,79

(6,73)

-0

(2) HOLES

INSTALLATION

STEP 3STEP 2

STEP 4

DRIVE PLATE

DRIVE EARS

1.25 HOLE

BINDER
POSTS

BINDER
POSTS

(31,75)

C

L

CYLINDER

LATCH
CUTOUT

1.718

(43,64)

BACKSET OF
DEADLATCH

C

L

3.000

(76,20)

SET SCREWS

1.PREPARE STILE AS SHOWN.

2.INSERT BINDER POST THRU .265 DIA. HOLE
IN STILE.

3.SECURE BINDER POST WITH 1/4-28 NUT.

(CAUTION: DO NOT OVERTIGHTEN NUT)

1.INSTALL 4500, 4700 AND 4900 SERIES
DEADLATCH PER MOUNTING INSTRUCTIONS.

2.INSTALL 4580 CAM DISC ASSY.
SECURE WITH SETSCREW.

4580

CAM DISC

ESCUTCHEON
ASSY.

SCREW &
LOCKWASHER

1.INSTALL ESCUTCHEON ASSY.

2.USING 8-32 SCREWS W/LOCKWASHER,
SECURE ESCUTCHEON ASSY. TO
BINDER POST.
IMPORTANT,
TIGHTEN THESE SCREWS SECURELY.

1.INSTALL PADDLE ASSY. ALIGN DRIVE EARS
ON PADDLE WITH SLOT IN DRIVE PLATE.

2.INSTALL PIVOT PIN.

3.INSTALL PIVOT PIN SET SCREW. TIGHTEN
SET SCREW FLUSH WITH BOTTOM OF
ESCUTCHEON.

PADDLE ASSY.

LABEL

PIVOT PIN

SET SCREW

INSTRUCTIONS FOR CHANGING HAND

DRIVER

DRIVER
SCREW

SCREW

PULL TO LEFT

OUTSIDE

INSIDE

1.FIND DESIRED CONFIGURATION.

2.REMOVE KEEPERS TO SEE LOCATION
OF SPRINGS & DRIVER PLATE.

www.adamsrite.com

Phone: [phone]

800-872-3267

Fax: [phone]

800-232-7329

80-0180-200

E

Rev.

PUSH TO LEFT

TOP

SEE REVERSE FOR CAM DISC ASSY.

DRIVER

DRIVER
SCREW

SCREW

PUSH TO RIGHTPULL TO RIGHT

LHRLHRHRRH

3.REVERSE SPRINGS & DRIVER
PLATE IF NECESSARY.

Ecn 11955A

Date: 06-19-12

4.REMOVE DRIVER SCREW IF NECESSARY,
AND PLACE IN DESIRED LOCATION.

SPRING

Page 1 of 2

KEEPER

4590 PADDLE OPERATOR

Appvd: MP

DRIVER SCREW

DRIVER PLATE

5.REPLACE KEEPERS.

6.CONFIGURE CAM DISC.
(SEE REVERSE)

Date: 06-19-12

4580 CAM DISC HANDING

LOOKING AT THE EDGE OF THE DOOR, DETERMINE ON WHICH
SIDE THE HANDLE OR OTHER OPERATOR IS TO BE INSTALLED.

STEP 1

THE CAM DISC MUST BE
HANDED AS SHOWN.

INSTRUCTIONS FOR CHANGING HAND OF 4580 CAM DISC

STEP 2

ON THIS SIDE

STEP 3

ON THIS SIDE

THE CAM DISC MUST BE
HANDED AS SHOWN.

STEP 4

REMOVE THE
RETAINER CLIP

www.adamsrite.com

Phone: [phone]

800-872-3267

Fax: [phone]

800-232-7329

PULL THE CAM PIVOT PIN OUT
OF THE CAM DISC AS SHOWN.

4591 PADDLE OPERATOR

80-0180-200

Rev.

DO NOT REMOVE
THE DRIVER PIECE

E

ECN: 11955A

TURN THE CAM OVER AND PUSH
THE CAM PIVOT PIN THRU THE
CAM AND INTO THE CAM DISC
AS SHOWN.

Date: 06-19-12

SNAP THE RETAINER CLIP
INTO THE GROOVE ON THE
CAM PIVOT PIN.

INSTALLATION INSTRUCTIONS

Page 2 of 2

Appvd: MP

Date: 06-19-12