Adams Rite 2290-302-103-10B, 2290-302-201-10B, 2290-310-101-32D, 2290-310-102-32D, 2290-310-103-32D Installation Instructions

STRIKE PREPARATION

HOLLOW METAL FRAME

DEADLATCH
IN DOOR

3 25/64"

4 1/8"

4 57/64"

1/8"

1 17/64"

C

L

5/8"

C

OF

L

LOCK

C

OF

L

STRIKE PLATE

1/8"

1 33/64"

INSTALLATION OF STRIKE

MOUNT STRIKE ONTO JAMB AND FASTEN WITH #10 FLAT
HEAD SCREWS AS SHOWN.

ONE WALL ONLY

4x,

2 5/16"

3 5/16"

TOOLS NEEDED:

- 5/64 ALLEN WRENCH

- 3/32 ALLEN WRENCH

- 1/8 ALLEN WRENCH

- #9 DRILL BIT (.196 Ø)

- #16 DRILL BIT (.177 Ø)

- 7/8 DRILL BIT (.875 Ø)

- 1-1/8 DRILL BIT (1.125 Ø )

13/64"

11/64"

1 7/32"

1 5/32"

2 33/64"

BACKSET

59/64"

31/32"

( EXTERIOR TRIM )

DOOR PREPARATION

1

59/64"

1 1/8"
ONE WALL
ONLY

1 1/8"
THRU ONE
WALL ONLY

31/32"

1/2"
ONE WALL ONLY
FOR
ELECTRIFIED OPTION

4 13/64"

5 1/32"

2 5/32"

8 1/64"

1 17/64"

HOLLOW METAL DOOR

PREPARATION

1 1/4"

BOTH WALLS

BACKSET

C

OF CYLINDER

L

7 1/4"

ONE WALL ONLY

- APPLY STICK ON TEMPLATE OVER CYLINDER BACKSET CENTER LINE.

NOTE: EACH TEMPLATE IS LABELED FOR OUTSIDE OR INSIDE TRIM.

- CENTER PUNCH ALL HOLES.

- DRILL HOLES AT CENTER PUNCH LOCATIONS. REMOVE TEMPLATE.

- INSTALL 2290 PER INSTALLATION INSTRUCTIONS.

4 13/64"

7/8"

31/32"

15/16"

31/32"

15/16"

1 5/32"

( INTERIOR TRIM )

FOR CYLINDER

13/64"

ONE WALL ONLY

4x,

1 7/32"

2 33/64"

13/64"

ONE WALL ONLY

11/64"

11/64"

2 15/64"

3 25/64"

EXTERIOR

"B"

8 1/64"

6 33/64"

5/32"

1"

*

*

*

**

WOOD DOOR PREPARATION

.50 DEEP

*

1.00 DEEP

**

7 1/4"

INTERIOR

BEVEL TABS ADJUSTMENT

2

- ROTATE BEVEL TABS TO DESIRED HANDING.
USING THE BEVEL ADJUSTMENT ALLOWS THE FLAT.
FACEPLATE TO WORK IN BEVEL STILES

AVAILABLE FACEPLATES

FLAT

Adams Rite Manufacturing Co.

260 Santa Fe Street,

Pomona, CA 91767

Phone: [phone]

Fax: [phone]

www.adamsrite.com

TO CHANGE THE HANDING
ON LATCH BOLT:

- DEPRESS THE LATCHBOLT UNTIL BOLT SCREW CAN BE
SEEN THROUGH CASE HOLE. (1-1/2" BACKSET ONLY).

- REMOVE BOLT SCREW AND ORIENT LATCH BOLT TO
THE OPPOSITE HAND.

- DEPRESS THE LATCH BOLT UNTIL THE COUNTERSINK
HOLE ON THE LATCH BOLT CAN BE SEEN THROUGH THE
CASE HOLE AS SHOWN IN FIG.1.

- REINSERT BOLT SCREW AND TIGHTEN TO 22 - 27 IN-LB.

RHR BEVEL

FLAT

3

LHR BEVEL

#6 x1/2"
BOLT SCREW

2290 INSTALLATION INSTRUCTIONS
W/ HEAVY DUTY ENTRANCE LEVER SET

80-0180-420

Rev.

C

ECN: 11735

#1-64 x 1/4"
FLAT HEAD SCREW

3a

LATCH
BOLT

1-1/2" BACKSET

FIG.1

1-1/8 BACKSET

- YOU WILL ALSO HAVE TO RE-ORIENT
THE INTER-CONNECT CAM:

a) LOOSEN THE #6-32 FLAT HD SCREW
AT THE BOTTOM OF THE LOCK.

b) ROTATE THE INTER-CONNECT CAM
TO THE OPPOSITE SIDE AND
RETIGHTEN THE FLAT HEAD SCREW
TO COMPLETE THE OPERATION

TO BLOCK HOLDBACK FEATURE

3a

- INSERT #1-64 x 1/4" FLAT HEAD
SCREW INTO CASE AS SHOWN
BEFORE INSTALLING IN DOOR.

FOR APPLICATION THAT REQUIRE

3b

RETRACTION OF THE DEADBOLT AND
DEARLATCH FROM BOTH SIDES OF
DOOR.

-REMOVE THE INTER-CONNECT CAM,
AND INSTALL THE OPTIONAL DOUBLE
INTER-CONNECT CAM.

LATCH
BOLT

#6-32
FLAT HD
SCREW

BEVELED
SIDE SHOULD
FACE THE SAME
DIRECTION AS THE
INTER-CONNECT
CAM

INTER-CONNECT
CAM

3b

DOUBLE INTER­CONNECT CAM
(P/N 27-0268)

b

BACK VIEW

INSTALLATION INSTRUCTIONS

Page of13

Appvd: B.C

Date:

02/25/11

a

8"

7 11/16"

63/64"

"B"

"A"

1 1/32"

1/2"

2 5/32"

3 13/64" 1 27/32"

1 47/64"

3/4"

INSTALLING LOCK TO THE BACK OF THE DOOR

4

- INSERT LOCK ASSEMBLY INTO DOOR THRU CUTOUT.

- INSTALL AND FASTEN TWO (2) FLAT HEAD SCREWS
#10-32 x 1-7/8" (OR #12, WOOD SCREW, P/N# 29-0271)
TO SECURE THE LOCK ASSEMBLY ON DOOR.

- INSTALL CYLINDER AND SECURE WITH SET SCREWS.

5

FLAT HD

SCREW

#10-32 x 1-7/8"

STRIKE PLATES ARE SHOWN

C

L

4"

LOCK

AT FRONT SIDE FOR CLARITY

OF

2 EA.

- INSTALL FACE PLATE.

TR* = A - B

TOLERANCE: ±.060

*

CYLINDER
SET SCREWS

"TR"

is trim ring length

"A"

is cylinder height (less

shoulder but including cam)

"B"

is one-half of door thickness

5 51/64"

5/8"

7/64"

C

OF

L

STRIKE
PLATE

CYLINDER
TRIM RING

DOOR STILE

A

11/16"

41/64"

7

ASSEMBLE EXTERIOR TRIM

6

HANDING CONFIGURATION FOR 2290 TRIM

- THE OUTPUT DRIVE FOR THE EXTERIOR TRIM IS SHIPPED FROM THE FACTORY IN A CLOCKWISE
ROTATION AND THE INTERIOR TRIM IS SHIPPED WITH A COUNTER-CLOCKWISE ROTATION.
TO CHANGE THE OUTPUT DRIVE ROTATION, FOLLOW THESE STEPS:

1. REMOVE THE SHOULDER SCREW WITH A 5/64" ALLEN WRENCH.

2. REINSTALL SHOULDER SCREW ON THE OPPOSITE SIDE.

DRIVE

REFER TO THE CHART BELOW FOR REHANDING THE TRIM AS NEEDED.

OUTPUT

SHOULDER

SCREW

-SLIDE THE FINISH COVER ONTO BODY. THE COVER HAS CUTOUTS THAT FIT OVER
THE GROOVES ON THE BODY.

- INSTALL BOTTOM CAP WITH (2) FLAT HEAD SCREWS (#4-40 x1/4") SUPPLIED.

- * FOR EXTERIOR TRIM WITH ELECTRIFIED OPTION. INSERT THE SHIELD ASSY
BETWEEN THE COVER AND THE EXTERIOR BODY BEFORE INSTALLING
THE BOTTOM CAP.

- INSTALL TOP CAP WITH (2) FLAT HEAD SCREWS (#4-40 x1/4") SUPPLIED.

CUTOUTS

GROOVES

LOCK CASE

CAM

DOOR

FLAT HD SCR
#4-40 x 1/4"
4 EA

TR

B

C

L

TOP
CAP

FINISH
COVER

BACK VIEW

EXTERIOR TRIM LHR

CW SHOWN

Adams Rite Manufacturing Co.

260 Santa Fe Street,

Pomona, CA 91767

Phone: [phone]

Fax: [phone]

www.adamsrite.com

INTERIOR TRIM LHR

CCW SHOWN

2290 INSTALLATION INSTRUCTIONS
W/ HEAVY DUTY ENTRANCE LEVER SET

80-0180-420

Rev.

C

ECN: 11735

FINISH
COVER

EXTERIOR

EXTERIOR
TRIM BODY

TRIM BODY

BOTTOM

CAP

*SHIELD
ASSY

INSTALLATION INSTRUCTIONS

Page of

2

Appvd: B.C

3

Date:

02/25/11

8

INSTALLING INTERIOR & EXTERIOR TRIM TO STILE

- INSERT DRIVE SPINDLE INTO EACH TRIM BODY
PRIOR TO MOUNTING.

- MOUNT THE EXTERIOR TRIM AND
INTERIOR TRIM BODY TO THE STILE
USING (6) #6-32 x 3" FLAT HEAD SCREWS.

- SLIDE THE COVER ONTO INTERIOR TRIM BODY
FROM THE TOP.

- INSERT SHAFT THRU THE HOLE ON THE
COVER AND THE OUTPUT ON TRIM BODY.
THE GROOVE ON THE SHAFT FACES
OPPOSITE THE LATCH BOLT.
TIGHTEN THE SET SCREW WITH A 3/32" ALLEN
WRENCH TO SECURE THE SHAFT AS SHOWN
IN FIG. 2.

- INSTALL TOP CAP USING (2) #4-40 x1/4" FLAT
HEAD SCREWS .

- PUSH THE COVER UP FLUSH WITH THE
TOP CAP, INSTALL BOTTOM CAP USING
(2) #6-32 x 3/8" FILLISTER HEAD SCREWS.

FIG. 2

EXTERIOR TRIM

3/32"
ALLEN
WRENCH

ELECTRIFIED
TRIM SOLENOID

GROOVE
OPPOSITE
LATCH BOLT

DRIVE
SPINDLE

DRIVE
SPINDLE

VOLTAGE
ADAPTOR CABLE

TOP CAP

FLAT HD SCREW
#4-40 x1/4" (2) EA

COVER

INTERIOR TRIM

SET SCREW
#10-24 x 1/4"
(3/32" ALLEN WRENCH)

SHAFT

FLAT HD SCREW
#6-32 x 3" (6) EA.

BOTTOM CAP

FILLISTER SCREW
#6-32 x3/8" (2) EA.

INSTALLING HANDLE (INTERIOR / EXTERIOR)

9

- INSERT WASHER THEN INSERT HUB OVER SHAFT.
ON HANDLES 2290-01, 2290-02, 2290-03, THE HUB IS FACTORY INSTALLED.
REMOVE LOCK SCREW WITH 1/8" ALLEN WRENCH AND PROCEED TO
NEXT STEP.

- INSTALL HANDLE OVER THE HUB WITH THE HOLE ALIGNED WITH
THE HOLE ON THE HUB.

NOTE: THE SHAFT DETENT SHOULD BE ALIGNED WITH THE LOCKING SCREW.

- MOVE THE HANDLE IN UNTIL IT IS AGAINST THE TRIM COVER.

- FASTEN THE LOCK SCREW 26-0933 TO SECURE THE HANDLE
WITH 1/8"ALLEN WRENCH.

SHAFT DETENT

WASHER

HUB

HANDLE

LOCK SCREW
26-0933
(1/8" ALLEN
WRENCH)

LATCH HOLD BACK FEATURE

- IN THE LOCK POSITION, INSERT KEY, TURN KEY
180° TO RETRACT THE DEADBOLT.

- TURN KEY 315° TO RETRACT THE LATCHBOLT.

- HOLD IN THIS POSITION AND PUSH DOWN
THE HOLD BACK BUTTON TO RETAIN LATCHBOLT.

- RETURN KEY TO NEUTRAL POSITION AND REMOVE KEY.

KEY OR
THUMB TURN

HOLD BACK
BUTTON

DEADBOLT

LATCH BOLT

TO RELEASE HOLD BACK

- INSERT KEY, TURN KEY OR THUMB TURN
ABOUT 135° AND HOLD.

- PUSH UP THE HOLD BACK BUTTON TO RELEASE
THE LATCH BOLT.

- RETURN KEY TO THE NEUTRAL POSITION
AND REMOVE KEY.

HOLD BACK

BUTTON
PUSH
DOWN

TEST OPERATION

- EXTEND DEADBOLT WITH KEY OR THUMBTURN.

- PUSH DOWN ON INTERIOR LEVER.
THE DEADBOLT AND LATCH SHOULD FULLY RETRACT.

- IF LATCH ONLY RETRACTS - REFER TO STEP 4 FOR
INTER-CONNECTION CONFIGURATION.

- IF NEITHER RETRACT - REFER TO STEP 11 FOR
DRIVE SPINDLE INSTALLATION.

- PUSH DOWN ON EXTERIOR LEVER - THE LATCH ONLY
SHOULD RETRACT.

HOLD BACK
BUTTON

PUSH
UP

ELECTRIFIED TRIM SOLENOID SPECIFICATION

SOLENOID AVAILABLE VOLTAGES
12V DC CONTINUOUS DUTY,
24V DC CONTINUOUS DUTY.

- WIRED THE VOLTAGE ADAPTOR CABLE TO THE
PROPER POWER SUPPLY THROUGH THE HOLE
ON THE STILE.

- CONNECTED THE CABLE TO THE EXTERIOR TRIM
SOLENOID BEFORE INSTALLING THE TRIM ONTO
THE STILE.

INTERMITTENT / CONTINUOUS DUTY 12 / 24V DC

120V AC

LINE

VOLTAGE

40 VA TRANSFORMER

2190 WIRING DIAGRAM

4603

RED -

4605 / 4606 -24V AC

RED -

2-AMP

RECTIFIER

WHITE (+)

DEADBOLT / DEADLATCH

BLACK (-)

2190

PRODUCT MUST BE INSTALLED

ACCORDING TO ALL APPLICABLE

BUILDING AND LIFE SAFETY CODES

Adams Rite Manufacturing Co.

260 Santa Fe Street,

Pomona, CA 91767

Phone: [phone]

Fax: [phone]

www.adamsrite.com

2290 INSTALLATION INSTRUCTIONS
W/ HEAVY DUTY ENTRANCE LEVER SET

80-0180-420

Rev.

C

ECN: 11735

INSTALLATION INSTRUCTIONS

Page of

3 3

Appvd: B.C

Date:

02/25/11