Adams Rite 2190-301-000, 2190-301-101-03, 2190-301-101-04, 2190-301-101-10B, 2190-301-101-32D Installation Instructions
...
STRIKE PREPARATION
1
DEADLATCH
IN DOOR
C'SNK FOR #10
FLAT HD SCREW
2 PLS
.080
4.645
5.375
.572
1.447
OUTSWING LOCK STILE PREPARATION ONLY
FOR INSWING DOORS USE SMALL FORMAT LEVERS (4600)
AND REFER TO 4600 INSTRUCTION WITH 2190
C
L
ALUMINUM FRAME
.218
2101 STRIKE PLATE
SHOWN
C
OF
L
CYLINDER
C
OF
L
STRIKE PLATE
(2 15/32")
6.375
1.340
ONE WALL ONLY
4x,
2.310
3.306
2x
#10-32
ONE WALL ONLY
1.212
2.520
BACKSET
.196
.177
.968
1.160
.928
.928
1.125
ONE WALL ONLY
1.125
THRU ONE
WALL ONLY
.968
.500
ONE WALL ONLY
FOR
ELECTRIFIED OPTION
4.200
5.025
C
OF
L
CYLINDER
R
1.010
1.594
6.375
4x
.156
BACKSET
6.885
ONE WALL ONLY
.938
4.200
.875
.968
.938
.968
1.250
BOTH WALLS
FOR CYLINDER
ONE WALL ONLY
4x,
1.160
ONE WALL ONLY
.196
.177
2.238
1.212
3.390
2.520
.196
.177
INSTALLATION OF STRIKE
- INSERT MOUNTING BACK PLATE BEHIND JAMB AND FASTEN WITH
#10 FLAT HEAD SCREWS.
- INSERT TRIM BOX WITH 2101 STRIKE PLATE AND FASTEN WITH
#10 FLAT HEAD SCREWS TO BACK PLATE AS SHOWN.
BEVEL TABS ADJUSTMENT
- ROTATE BEVEL TABS TO DESIRED HANDING.
USING THE BEVEL ADJUSTMENT ALLOWS THE FLAT.
FACEPLATE TO WORK IN BEVEL STILES
RHR BEVEL
LHR BEVEL
AVAILABLE FACEPLATES
FLAT
RADIUS
RADIUS WEATHER STRIP
Adams Rite Manufacturing Co.
260 Santa Fe Street,
Pomona, CA 91767
Phone: 909-632-2300
Fax: 909-632-2369
www.adamsrite.com
FLAT or RADIUS
2190 INSTALLATION INSTRUCTIONS
W/ HEAVY DUTY ENTRANCE LEVER SET
80-0180-410
TOOLS NEEDED:
- 5/64 ALLEN WRENCH
BACK OF LOCK STILE
- 3/32 ALLEN WRENCH
- 1/8 ALLEN WRENCH
- #9 DRILL BIT (.196 Ø)
- #16 DRILL BIT (.177 Ø)
- 7/8 DRILL BIT (.875 Ø)
- 1-1/8 DRILL BIT (1.125 Ø )
FOR RADIUS FACEPLATE
WITH WEATHERSEAL ONLY !
- WITH A SMALL FLAT HEAD
SCREWDRIVER, PRY OFF
BEVEL TABS AS SHOWN.
Rev.
D
( EXTERIOR TRIM )
32
1-1/2" BACKSET
SHOWN
#6 x1/2"
BOLT SCREW
ECN: 11883
- APPLY STICK ON TEMPLATE OVER CYLINDER BACKSET CENTER LINE.
NOTE: EACH TEMPLATE IS LABELED FOR OUTSIDE OR INSIDE TRIM.
- CENTER PUNCH ALL HOLES.
- DRILL HOLES AT CENTER PUNCH LOCATIONS. REMOVE TEMPLATE.
- INSTALL 2190 PER INSTALLATION INSTRUCTIONS.
TO CHANGE THE HANDING
ON LATCH BOLT:
- DEPRESS THE LATCHBOLT UNTIL BOLT SCREW CAN BE
SEEN THROUGH CASE HOLE. (1-1/2" BACKSET ONLY).
- REMOVE BOLT SCREW AND ORIENT LATCH BOLT TO
THE OPPOSITE HAND.
- DEPRESS THE LATCH BOLT UNTIL THE COUNTERSINK
HOLE ON THE LATCH BOLT CAN BE SEEN THROUGH THE
CASE HOLE AS SHOWN IN
- REINSERT BOLT SCREW AND TIGHTEN TO 22 - 27 IN-LB.
#1-64 x 1/4"
FLAT HEAD SCREW
LATCH
BOLT
3a
FIG.1.
1-1/2 BACKSET
Date:
02/03/2012
1-1/8 BACKSET
FIG.1
- YOU WILL ALSO HAVE TO RE-ORIENT
THE INTER-CONNECT CAM:
a)
LOOSEN THE #6-32 FLAT HEAD SCREW
AT THE BOTTOM OF THE LOCK.
b)
ROTATE THE INTER-CONNECT CAM
TO THE SAME DIRECTION AS THE
LATCH BOLT BEVEL.
RETIGHTEN THE #6-32 FLAT HEAD
SCREW TO COMPLETE THE
OPERATION.
TO BLOCK HOLDBACK FEATURE:
3a
- INSTALL #1-64 x 1/4" FLAT HEAD
SCREW INTO CASE AS SHOWN
BEFORE INSTALLING IN DOOR.
FOR APPLICATIONSTHAT REQUIRE
3b
RETRACTION OF THE DEADBOLT
AND DEADLATCH FROM BOTH
SIDES OF THE DOOR.
INTER-CONNECT CAM, AND INSTALL
THE OPTIONAL DOUBLE
INTER-CONNECT CAM.
REMOVE THE
INSTALLATION INSTRUCTIONS
Page of13
BEVELED
SIDE SHOULD
FACE THE SAME
DIRECTION AS THE
INTER-CONNECT
CAM
INTERCONNECT CAM
DOUBLE INTERCONNECT CAM
(P/N 27-0268)
Appvd: BC
( INTERIOR TRIM )
LATCH
BOLT
#6-32
FLAT HD
SCREW
a
b
BACK VIEW
3b
Date: 02/09/12
.980
"B"
"A"
.476
FOR TRADITIONAL MOUNTING INSTALLATIONS
4
- MEASURE THE DEPTH FROM THE BACK OF THE LOCK STILE
TO THE INSIDE WALL OF THE LOCK STILE.
- MATCH THE DISTANCE FROM THE FACE OF MOUNTING
PLATE TO END OF BOTH TUBE SPACERS.
- USE 3/16" HEX KEY FOR FINE ADJUSTMENT.
FOR MOUNTING TAB INSTALLATIONS
5
-REMOVE TOP AND BOTTOM FLAT HEAD UNDERCUT
SCREW #8-32 x 1/4"AS SHOWN.THEN REMOVE YOKE.
(MOUNTING TABS NOT INCLUDED).
FLAT HD UNDERCUT SCREW
#8-32 x 1/4"
1.587
1.004
5.80
6.874
.626
INSTALLING LOCK TO THE BACK OF THE STILE
6
- INSERT LOCK ASSEMBLY INTO LOCK STILE THRU CUTOUT.
- INSTALL AND FASTEN TWO (2) FLAT HEAD SCREWS
#10-32 x 1-7/8" TO SECURE THE LOCK ASSEMBLY ON STILE.
7
- INSTALL CYLINDER AND SECURE WITH SET SCREWS.
- INSTALL FACE PLATE.
FLAT HD
SCREW
#10-32 x 1-7/8"
CYLINDER
SET SCREWS
PLATE
2 EA.
FACE
1.362
1.737
2.856
.750
STRIKE PLATES ARE SHOWN
AT FRONT SIDE FOR CLARITY
C
OF CYLINDER
L
2 15/32"
3.200
C
OF
L
STRIKE
PLATE
.688
SET SCREW
TR* = A - B
TOLERANCE: ±.060
*
"TR"
is trim ring length
"A"
is cylinder height (less
shoulder but including cam)
"B"
is one-half of door thickness
CYLINDER
TRIM RING
DOOR STILE
A
LOCK CASE
CAM
C
DOOR
CYLINDER
TR
B
L
MATCH MEASURED
INSIDE
LOCK
STILE
WALL
3/16"
HEX KEY
HANDING CONFIGURATION FOR 2190 TRIM
8
- THE OUTPUT DRIVE FOR THE EXTERIOR TRIM IS SHIPPED FROM THE FACTORY IN A CLOCKWISE
ROTATION AND THE INTERIOR TRIM IS SHIPPED WITH A COUNTER-CLOCKWISE ROTATION.
TO CHANGE THE OUTPUT DRIVE ROTATION, FOLLOW THESE STEPS:
1. REMOVE THE SHOULDER SCREW WITH A 5/64" ALLEN WRENCH.
2. REINSTALL SHOULDER SCREW ON THE OPPOSITE SIDE.
REFER TO THE CHART BELOW FOR REHANDING THE TRIM AS NEEDED.
OUTPUT
SHOULDER
BACK VIEW
EXTERIOR TRIM LHR
CW SHOWN
DRIVE
SCREW
INTERIOR TRIM LHR
CCW SHOWN
DISTANCE
YOKE
ADJUST
TUBE
SPACERS
EQUALLY
ASSEMBLE EXTERIOR TRIM
9
-SLIDE THE FINISH COVER ONTO BODY. THE COVER HAS CUTOUTS THAT FIT OVER
THE GROOVES ON THE BODY.
- INSTALL TOP CAP WITH (2) FLAT HEAD SCREWS (#4-40 x1/4") SUPPLIED.
- *FOR EXTERIOR TRIM WITH ELECTRIFIED OPTION. INSERT THE SHIELD ASSY
BETWEEN THE COVER AND THE EXTERIOR TRIM BODY BEFORE INSTALLING
THE BOTTOM CAP.
- INSTALL BOTTOM CAP WITH (2) FLAT HEAD SCREWS (#4-40 x1/4") SUPPLIED.
FINISH
COVER
CUTOUTS
FINISH
COVER
TOP CAP
FLAT HD SCR
#4-40 x 1/4"
4 EA
GROOVES
EXTERIOR
TRIM BODY
EXTERIOR
TRIM BODY
BOTTOM
CAP
*SHIELD
ASSY.
Adams Rite Manufacturing Co.
260 Santa Fe Street,
Pomona, CA 91767
Phone: 909-632-2300
Fax: 909-632-2369
www.adamsrite.com
2190 INSTALLATION INSTRUCTIONS
W/ HEAVY DUTY ENTRANCE LEVER SET
80-0180-410
Rev.
D
ECN: 11883
Date:
02/03/2012
INSTALLATION INSTRUCTIONS
Page of23
Appvd: BC
Date: 02/09/12
Loading...