ADA instruments Cube MINI Professional Edition, Cube MINI Basic Edition User Manual
INSTRUMENTS
MEASUREMENT FOUNDATION
Operating manual
Line laser level
ADA CUBE MINI
Manufacturer: ADAINSTRUMENTS Address: WWW.ADAINSTRUMENTS.COM
CUBE MINI
Table of contents
1. Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. Change of batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5. Laser lines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
8. To check the accuracy of line laser level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
9. Care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
10. Specic reasons for erroneous measuring results . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
11. Electromagnetic acceptability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
12. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
13. Exceptions from responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
14. Appendix 1- “Certicate of acceptance and sale”
15. Appendix 2- “Warranty card”
2
INSTRUMENTS
Kit
Cross line laser, batteries, operating manual, a tripod (optional). Manufacturer may modify complete set
without notice.
Application
Cross Line Laser projects visible laser planes. It is used for determination height, making horizontal and
vertical planes.
Specications
Leveling Range self-leveling, ±3°
Accuracy ±2mm/10m
Working Range 20 m* (*depends on illumination of work area)
Power Supply 2xAA Batteries Alkaline
Laser Source 2 x 635nm
Operating temperature -10°C to 45°C
Laser class 2
Dimensions 65х65х45 mm
Weight 190 g
CUBE MINI
3
INSTRUMENTS
Change of batteries
Open battery compartment. Put in 2x AA Alkaline batteries. Take care to correct polarity. Close battery compartment.
ATTENTION: If you are not going to use instrument for a long time, take out batteries.
Laser lines
4
CUBE MINI
INSTRUMENTS
Features
CUBE MINI
3
1. laser emitting window
2. battery cover
3. compensator switch
4. tripod mount 1/4"
2
1
4
5
INSTRUMENTS
Operation
Place the instrument on the working surface or mount it on the tripod/pillar or wall mount (comes with the
instrument).
Switch on the instrument: turn the compensator switch (3) to the position “ON”.
When enabled, the vertical and horizontal plane projected constantly. Visual alarm (blinking line) and
audible signal indicate that the device was not installed within the compensation range ± 3 º. To properly
work align the unit in a horizontal plane.
6
CUBE MINI
INSTRUMENTS
CUBE MINI
APPLICATION DEMONSTRATION
For more information you can visit our website
www.adainstruments.com
7
INSTRUMENTS
To check the accuracy of line laser level
To check the accuracy of line laser level (slope of plane)
Set up the instrument between two walls, the distance is 5
m.Turn on the Cross Line Laser and mark the point of cross
laser line on the wall.
Set up the instrument 0,5-0,7m away from the wall and make, as
described above, the same masrks. If the difference {a1-b2} and
{b1-b2} is less then the value of “accuracy” (see spesications),
there is no need in calibration.
Example: when you check the accuracy of Cross Line Laser the
difference is {a1-a2}=5 mm and {b1-b2}=7 mm. The
instrument’s error: {b1-b2}-{a1-a2}=7-5=2 mm. Now you can
compare this error with standard error.
If the accuracy of Cross Line Laser isn’t corresponding with
claimed accuracy, contact the authorized service center.
8
CUBE MINI
INSTRUMENTS
m
To check level
Choose a wall and set laser 5M away from the wall. Turn
on the laser and cross laser line is marked A on the wall.
Find another point M on the horizontal line, the distance is
around 2.5m. Swivel the laser, and another cross point of
cross laser line is marked B. Please note the distance of
B to A should be 5m.
Measure the distance between M to cross laser lune, if
the difference is over 3mm, the laser is out of calibration,
please contact with seller to calibrate the laser.
To check plumb
Choose a wall and set laser 5m away from the wall. Mark
point A on the wall, please note the distance from point A
to ground should be 3m. Hang a plumb line from A point
to ground and nd a plumb point B on ground. turn on
the laser and make the vertical laser line meet the point
CUBE MINI
m
9
INSTRUMENTS
B, along the vertical laser line on the wall and measure the distance 3m from point B to another point C.
Point C must be on the vertical laser line, it means the height of C point is 3m.
Measure the distance from point A to point C, if the distance is over 2 mm, please, contact with seller to
calibrate the laser.
Care and cleaning
Please handle measuring instrument with care. Clean with soft cloth only after any use. If necessary
damp cloth with some water. If instrument is wet clean and dry it carefully. Pack it up only if it is perfectly
dry. Transport in original container/case only.
Note: During transport On/Off compensator lock (3) must be set to position “OFF”. Disregard may lead to
damage of compensator.
Specic reasons for erroneous measuring results
• Measurements through glass or plastic windows;
• Dirty laser emitting window;
10
CUBE MINI
INSTRUMENTS
• After instrument has been dropped or hit. Please check the accuracy.
• Large uctuation of temperature: if instrument will be used in cold areas after it has been stored in
warm areas (or the other way round) please wait some minutes before carrying out measurements.
•
Electromagnetic acceptability (EMC)
• It cannot be completely excluded that this instrument will disturb other instruments (e.g. navigation
systems);
• will be disturbed by other instruments (e.g. intensive electromagnetic radiation nearby industrial
facilities or radio transmitters).
Laser class 2 warning label on the laser instrument
CUBE MINI
11
Loading...