ADA INSTRUMENTS AeroTemp User Manual [ru]

Operating manual

Anemometer

Model: AeroTemp

Manufacturer

Address: WWW. ADAINSTRUMENTS.COM

Table of contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2. Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3. Illustration of display screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4. Operation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

5. Trouble shootings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

6. Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

7. Warranty/Exceptions from responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Appendix 1. Certificate of acceptance and sale Appendix 2. Warranty card

AeroTemp

INTRODUCTION

ADA AeroTemp anemometer is a unit with high stability and advanced sensor technology. It is suitable for the measurement of air speed and temperature under normal ambient temperature. It is a ideal instrument in environmental monitor stations, hospitals, building air conditioning heating, ventilation test and calibrating temperature. This model has the advantages of easy operation, rapid measurement, safe usage and portability. It has backlight LCD display and has the function of default parameters saved and measurement data maintained automatically which can avoid to reset for each power on.

AeroTemp

APPEARANCE

1. Impeller protection cap

2. Impeller

3. Temperature measurement sensor parts

4. LCD screen

5. Temperature unit switch button UNIT

6. Power/ Wind chill button /WCI

7. Set//HOLD button;

8. Safety sling

9. Battery compartment

ILLUSTRATION OF DISPLAY SCREEN

A) Air speed unit: m/min B) Air speed unit: m/s C) Air speed unit: km/hr D) Air speed unit: ft/min E) Air speed unit: m/h F) Air speed unit: knots G) Maximum wind speed indicator H) Minimum wind speed indicator I) Average wind speed indicator J) Low battery display indicator K) Screen hold indicator L) Wind chill indicator M) Wind speed value N) Temperature value O) °F indicator P) °C indicator

AeroTemp

OPERATION INSTRUCTIONS

1. Unscrew the battery lid according to the arrows direction, remove insulation pad under the battery and place a CR2032 button battery according to the polarity indication, then put back the battery lid.

2. Press WCI button to power on the unit and the default status is wind speed and environment temperature mesurement .

3. Wind speed measurement: pull out the impeller protection cap to make the fan vertical to wind direction. Current wind speed will be displayed on the up line of the screen.

4. Adjustment of wind speed display mode: in normal state, press SET/HOLD button to change display mode. Press each time to switch from real-time, MAX, MIN, AVG in turns and display corresponding signs and no sign indicator for real time mode.

5. Adjustment of wind speed unit: in normal state, press UNIT button, the wind speed unit flashes. then press SET/HOLD button to switch the units (m/m, m/s, km/h , ft/m, m/h, knots). Each press will make corresponding unit flashes. Press UNIT button twice to exit this mode. The units don’t flash any more and return to normal state.

6. Adjustment of temperature unit: in normal state, press UNIT button twice continuously to enter this mode. At this time, the temperature unit flashes. Then press SET/HOLD button to switch between °F and °C. Each press can make corresponding temperature unit flashes. Press UNIT button again to exit this mode. The temperature units don’t flash any more and return to normal state.

7. The screen hold function: in normal state, hold SET/HOLD button for 2 seconds to lock the screen content and “HOLD” sign appears. Press this buttton again to release lock and return to normal state. Notes: During hold period, if battery lack of power, low battery indicator will appear on the screen.

8. Environment temperature and wind chill temperature display: in normal state, environemnt temperature displayed in below line. Press /WCI button to display wind chill in below line and WCI sign. Press again to return to environment temperature display and WCI sign disappears. Note: Wind chill is only used for the wind speed >1.34m/s ((4.8km/h).

9. Power off the unit: hold /WCI button for more than 2S to power off the unit.

Operation notes

1. Please don’t operate this product unless the manual has been read.

2. To ensure the accurracy, pull out the impeller protection cap before use and make sure the sensor fully contact with the measured environment and the fan be vertical to the wind direction.

3. Please don’t make pressure to the two sides of the impeller to avoid harming the impeller axle and affect the measurement accuracy.

4. The low battery indication will appear on the screen when lack of power.

5. Backlight off after 15s: the backlight off if no action in 15s.

6. Power off after 5 minutes: the unit will power off automatically in about 5 minutes if no action and the impeller stops running.

7. Parameters memory function setting: after setting the parameter, it stores automatically. Next power-on, it measures as the last set parameters.

8. Don’t immerse the product into liquid.

9. Don’t make the unit close to the magnet.

10. To avoid damages to the instrument, do not use it near following places: a) Environment has vapor and dust; b) EMF places (Electro-magnetic fields: such as arc welders, induction heaters) c) Static environment

Battery Safety Instructions

● Please remove the batteries when clean the product.

● Remove the batteries before long term storage

● Please install the batteries properly as the instructions of the positive and negative charges

AeroTemp

● Please dispose the waste batteries properly. High temperature will cause explosions and do not burn the batteries. Strap insulated

tape around the battery charges to avoid unsafe contacts with other objects. Many countries have regulations about the batteries disposing. Please follow the local regulations of battery disposing.

Cautions

● Handle with care and do not let the unit drop down.

● Do not disassemble the unit to avoid failure.

● Please put back the impeller protection cap when not in use.

● Do not place the unit together with corrosive gases or objects.

● Please keep clean and keep away from water.

● Avoid dust and water, which may stain the unit.

● Don’t immerse the product into water, which will result in damage to product.

● Please remove the battery, if it is not for use for a long time.

TROUBLE SHOOTINGS

Problems Causes Solutions

No display on the screen Battery runs down Check and replace the battery

Low battery Replace the battery

Show “ ” sign

TECHNICAL DATA

AeroTemp

Measuring range (temperature) 0°C~50°C

Measuring range (wind speed) 0.4~30.0 m/s

80~5910 ft/min

Measuring accuracy (temperature) ±1.2°C

Measuring accuracy (wind speed) ±(3% +0.2 m/s),

±(3% +40 ft/min)

Resolution: temperature 0.1°C

Wind speed 0.1m/s

1ft/min

Wind speed response time <2s

Backlight off time About 15s

Automatic off About 5 minutes

Power supply CR2032

Working current Backlight light on<10mA;

No backlight <3mA

Standby current <150uA

Operating temperature 0°C~50°C

Working humidity 5%~95%RH

non-condensing

Storage Condition -30~60°C

<85% RH (w/o batteries)

Size 148mm×53mm×22mm

Weight About 78.5g

(w/o batteries)

+ 18 hidden pages