AcuRite 01512, 01531 Instruction Manual

Instruction Manual

Professional Weather Center

model 01512 / 01531

CONTENTS

Unpacking Instructions ........... 2

Package Contents .................. 2

Product Registration ............... 2

Features & Benets: 5-in-1....... 3

Features & Benets: Display.... 4

Back of Display...................... 6

Setup .................................... 7

5-in-1 Sensor Setup ................ 7

Display Setup ........................ 8

Set the Time, Date & Units ...... 9

Backlight Settings ................... 9

Placement Guidelines ............10

Questions? Contact Customer Support at

5-in-1 Sensor Installation........11

Using the Weather Center .....12

Rainfall Tracking ...................13

Weather Ticker .....................14

Troubleshooting ....................15

Care & Maintenance............. 17

Calibration ...........................17

Specications........................19

FCC Information ...................19

Customer Support ................ 20

Warranty............................. 20

[phone] or visit www.AcuRite.com.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

Congratulations on your new AcuRite product. To ensure the best
possible product performance, please read this manual in its entirety

and retain it for future reference.

Unpacking Instructions

Remove the protective lm that is applied to the LCD screen prior to using this
product. Locate the tab and peel off to remove.

Package Contents

1. Display with Tabletop Stand

2. 5-in-1 Sensor

3. Sensor Mounting Bracket

4. Mounting Hardware

5. Power Adapter

6. Instruction Manual

IMPORTANT

PRODUCT REGISTRATION

Register online

to receive 1 year

warranty protection

www.AcuRite.com

PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE

Archive:l Products

Register a Product

►

2

Features & Benets

7

1

2

9

11

6

5-in-1 SENSOR

1. Rainfall Collector Funnel

2. Solar Cell Panel

Converts sunlight into power to run
internal aspirating fan.

Internal Aspirating Fan

(not shown)

Draws ambient air into
sensor to reduce solar radiation
heating, resulting in more accurate

temperature measurement.

3. A-B-C Switch

ID code that must match display’s
A-B-C switch to ensure units
synchronize.

4. Battery Compartment

4

3

5

8

10

5. Temperature & Humidity Sensors

(internal)

6. Mounting Point

7. Wind Speed Anemometer

8. Wind Direction Vane

9. Mounting Bracket

10. Mounting Hardware

includes anchors & screws.

Qty Diameter Length

5 #4 3/4”
1 #4 1/2”
1 #6 1/2”

11. Debris Filter

Pre-installed to prevent debris from

entering the rain gauge.

3

Features & Benets

Display Unit

31

30
29

28
27

26
25

24

23

1 2 3 1 4

ARNING

cC':',---

,, 1, 1, II 1, II I &

'""'

5
6

7
8

9
10
11

12
13
14

15
16

22

21 20 19 18 17

4

1. Previous 2 Wind Directions

2. Current Wind Speed

3. Current Wind Direction

4. Current Indoor Temperature

Arrow icon indicates direction

temperature is trending.

5. Display Low Battery Indicator

6. Peak Wind Speed

Highest speed from the last 60

minutes.

7. Current Indoor Humidity

Arrow icon indicates direction
humidity is trending.

8. Wind Speed Alert Indicator

Activates when wind speed is over

50 mph.

9. Clock

10. Rainfall Alert Indicator

Indicates rainfall of more than 1”
(25 mm) of rain in 2 hours or less.

11. AUTO DIM Indicator

Indicates display is in auto-dimming

brightness mode (see page 9).

12. Current Rainfall Total

Accumulates data during rainfall.

13. 12 to 24 Hour Weather Forecast

Self-Calibrating Forecasting pulls
data from your 5-in-1 sensor to
generate your personal forecast.

14. Storm Alert Indicator

Activates when barometric

pressure drops.

15. Month/Year/All-Time Rainfall

16. Current Barometric Pressure

Arrow icon indicates direction

pressure is trending.

17. RAINFALL Button

Press to change the RAINFALL
data being displayed (Month, Year,
All-Time).

A

18. TButton

For setup preferences.

19. SET Button

For setup preferences.

20. V Button

For setup preferences.

21. SELECT Button

Press to change the WEATHER
SELECT category data being
displayed.

22. Weather Ticker

23. Heat Index/ Wind Chill Alert
Indicator

Activates when heat index rises

over 90ºF (32ºC) or when wind

chill drops below -17ºF (-27ºC).

24. Learning Mode Icon

Disappears after weather forecast
self-calibration is complete.

25. WEATHER SELECT

Displays heat index, dew point, wind
chill, feels like, days with rain this
month, and days since last recorded
rainfall.

26. Date

27. Current Outdoor Humidity

Arrow icon indicates direction
humidity is trending.

28. Average Wind Speed

Average of all speeds over the past

2 minutes.

29. 5-in-1 Sensor Signal Strength

30. Sensor Low Battery Indicator

31. Current Outdoor Temperature

Arrow icon indicates direction

temperature is trending.

TM

5

Back of Display Unit

1

2

3

6

5

4

BACK OF DISPLAY UNIT

1. Integrated Hang Hole

For easy wall mounting.

2. Button

Dimmer control while using power
adapter. Activates momentary
backlight while on battery power.

3. Plug-in for Power Adapter

4. Removable Tabletop Stand

5. CLEAR ALL/RESET Button

Press to clear record currently being

viewed. Press AND HOLD for more
than 10 seconds for full reset to
factory defaults.

6. A-B-C Switch

ID code that must match 5-in-1
sensor’s A-B-C switch to ensure
units synchronize.

7. Power Adapter

8. Battery Compartment Cover

(not shown)

6

7

SETUP

5-in-1 Sensor Setup

Set the A-B-C Switch

1

•

Locate the A-B-C switch inside the
battery compartment. Set the A-B-C
switch to A, B or C. You must select
the same letter choices for both the
sensor and the display in order for
the units to synchronize.

Install or Replace Batteries

2

•

Batteries MUST be installed for
this product to operate. AcuRite
recommends high quality alkaline
or lithium batteries for the best
product performance. Heavy duty
or rechargeable batteries are not

recommended.

The 5-in-1 sensor requires lithium
batteries in low temperature
conditions. Cold temperatures can

cause alkaline batteries to function
improperly. Use lithium batteries in

the 5-in-1 sensor for temperatures

below -4ºF / -20ºC.

1. Slide off the battery

compartment cover.

2. Insert 4 x AA batteries into the

battery compartment, as
shown. Follow the polarity
(+/-) diagram in the battery

compartment.

3. Replace the battery cover.

3

Remove Rain Gauge Stabilizer

•

Locate and remove the rain gauge
stabilizer (plastic tab) taped into

the bottom of the sensor. The rain

gauge will not function until this is

removed.

A-B-C Switch

1

Set to match

•

display

2

•

A B C

Install Batteries

4 AA Batteries

Rain Gauge Stabilizer

3

7

Remove and discard

Display Unit Setup

AcuRite recommends high quality alkaline batteries for the best product
performance. Heavy duty or rechargeable batteries are not recommended.

Set the A-B-C Switch

1

The A-B-C switch is located inside

• •

the battery compartment. It can be
set to A, B or C. However, you must
select the same letter choices for
both the sensor and the display unit
in order for the units to synchronize.

1

A B C

Plug Power Adapter into

2

Electrical Outlet

Install or Replace Batteries

3

(optional)

•

Insert 6 x AA alkaline batteries
into the battery compartment,
as shown. Follow the polarity
(+/-) diagram in the battery

compartment.

Install Backup

3

Batteries

6 AA Batteries
(optional)

Plug in Power

2

Adapter

IMPORTANT: Batteries are a backup power source to preserve records in the event of

a power outage. Power adapter is the recommended primary power source to enjoy
the full functionality of this product.

PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.

used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used
batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire,
as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge
non-rechargeable batteries. DO NOT short-circuit the supply terminals.

BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be

8

Set the Time, Date & Units

Press the “S ET” button, located on the front of the display, to enter SET
MODE. Once in set mode, the preference you are currently setting will blink on
the display.

To adjust the currently selected (ashing) item, press and release the “T“ or

“V“ buttons (press and HOLD to fast adjust).

To save your adjustments, press and release the “S ET ” button again to adjust
the next preference. The preference set order is as follows:

TOP DISPLAY:

CLOCK HOUR
CLOCK MINUTE
CALENDAR MONTH
CALENDAR DATE
CALENDAR YEAR
TEMPERATURE UNITS (ºF or ºC)
WIND SPEED UNITS (MPH, KPH, Knots)
RAINFALL UNITS (in or mm)
PRESSURE UNITS (inHg or hPa)

TICKER DISPLAY:

LANGUAGE (English, French, Spanish)
WEATHER TICKER SPEED (SLOW, MEDIUM, FAST)

You will automatically exit SET MODE if no buttons are pressed for 20 seconds.
Enter SET MODE at any time by pressing the “SE T” button.

Display Backlight Settings

This weather station’s color display features three different lighting settings:
High (100%) brightness, Medium (60%) brightness and Low (30%) brightness.

Using battery power alone, the backlight is available momentarily for 10
seconds by pressing the “ ” button.

When display is powered with the power adapter, backlight remains on at
100% brightness. Press “ ” button once to dim to 60% brightness; press
again to dim to 30%, press a 3rd time to enter “AUTO DIM” mode. “AUTO
DIM” will appear below the time.

AUTO DIM MODE: Automatically adjusts display brightness based on time of day & year.

MARCH 11- NOVEMBER 4

NOVEMBER 5 - MARCH 10

6:00 a.m. - 9:00 p.m. = 100% brightness
9:01 p.m. - 5:59 a.m. = 30% brightness
7:30 a.m. - 7:00 p.m. = 100% brightness
7:01 p.m. - 7:29 a.m. = 30% brightness

9

10

View Video

www.AcuRite.com/5in1

video, or learn more about AcuRite technology:
Visit us online to view installation photos and

structures around to ensure accurate wind measurement.

Consider a location that is a wide open area, with few
DO NOT mount the sensor with obstructions around it.

LOCATE AWAY FROM WIND & RAIN OBSTRUCTIONS

may force water inside the sensor.
DO NOT install the sensor where it will be sprayed by a sprinkler system. This

LOCATE AWAY FROM SPRINKLER HEADS

sources may impact humidity accuracy.
Avoid installing the sensor near pools, spas, or other bodies of water. Water

LOCATE AWAY FROM HUMIDITY SOURCES

asphalt and concrete (surfaces that radiate heat).
Position sensor away from heaters, air conditioners, chimneys, exhaust vents,

LOCATE AWAY FROM HEAT SOURCES

computer, microwave, radio, etc.).

Place both units at least 3 feet (.9 m) away from electronic devices (TV,

PREVENT WIRELESS INTERFERENCE

objects that may limit wireless communication.
Place units away from large metallic items, thick walls, metal surfaces, or other

MAXIMIZE WIRELESS RANGE

Display and sensor must be within 330 feet (100 m) of each other.

Important Placement Guidelines

the sensor for the most accurate measurements.

Choose an open location with no obstructions above or around
The 5-in-1 sensor is designed to remain outdoors all year long.

5-in-1 Sensor Placement

~

tabletop use or is wall-mountable.
and away from heat sources or vents. Display stands upright for
accurate temperature measurement, place out of direct sunlight
Place the display in a dry area free of dirt and dust. To ensure

L~

Display Placement

'.OL

performance of this product.

placement of both the display and the sensor are critical to the accuracy and
AcuRite sensors are sensitive to surrounding environmental conditions. Proper

Placement for Maximum Accuracy

5-in-1 Sensor Installation Guidelines

INSTALLATION HEIGHT Mount the sensor at a minimum height of 5 feet

(1.5 meters) off the ground, in an open area. Higher is better for wind

measurements - The National Weather Service recommends 33 feet high!

MOUNTING OPTIONS The included mounting bracket it designed to screw

directly onto wooden posts or surfaces that are 2x4 or larger. The sensor can
also be mounted directly to common 3/4” steel pipe (available at hardware

stores and home centers).

LEVEL INSTALLATION Use the bubble level

(included on top of sensor) to ensure level
installation for accurate wind measurement.

SOLAR CELL INSTALLATION Install the

sensor with the solar cell facing SOUTH.

This ensures the cell receives as much sun
as possible and orients wind direction.

5-in-1 Sensor Installation

1. Fasten mounting base (included) to a
post or pole (not included) using the 4
longer screws included in the hardware

bag.

NO OBSTRUCTIONS

ABOVE OR AROUND

SOUTH

at least

t

(1.5 meters)

5 Feet

l from

2. Insert the mounting base into the hole

on the bottom of the sensor.

~

'f ground

3. Make sure the arrows on the top of
the sensor are pointed in the proper

direction and the bubble level is
centered. The solar cell should be
facing south to properly orient the wind

direction.

4. Fasten the sensor into the mounting base using the 2 shorter screws included

in the hardware bag.

The 5-in-1 sensor is now ready to use.

Clear Data Collected During Installation

When installation is complete, press and HOLD “CLEAR ALL/RESET” button,
located on the back of the display inside the battery compartment, to clear
erroneous data from the display.

Basic Setup is Complete

The 5-in-1 sensor will now synchronize with the display. It may take a few
minutes for synchronization to complete. If both or one of the units appear to
be functioning improperly, please refer to the troubleshooting section.

11

OPERATION

Using the Professional Weather Center

Learning Mode

Self-Calibrating Forecasting use a unique algorithm to analyze changes in
pressure over a time period (called Learning Mode) to determine your altitude.
After 14 days, the Learning Mode icon disappears from the display screen. At
this point, the self-calibrated pressure is tuned in to your location and the unit is
ready for superior weather prediction.

Weather Forecast

AcuRite’s patented Self-Calibrating Forecasting provides your personal forecast
of weather conditions for the next 12 to 24 hours by collecting data from
the sensor in your backyard. It generates a forecast with pinpoint accuracy ­personalized for your exact location.

STORMY

& WINDY

(flashing=stormy)

View the complete list of icons at www.AcuRite.com/acurite-icons

SNOW

LIKELY

~

.. tr ..... It

SNOW / RAIN

MIX LIKELY

CHANCE
OF RAIN

~

II II II If I

CLOUDY

~

Weather Select

Weather Select displays data including wind chill, dew point, heat index, feels
like, days with rain this month, and days since last recorded rainfall. To change
the “Weather Select” category shown, press the “SELECT” button on the front
of the display.

Barometric Pressure

Subtle variations in barometric pressure greatly affect the weather. This
weather center displays the current pressure with an arrow icon to indicate the
direction the pressure is trending (FALLING, STEADY, or RISING).

12

Rainfall Tracking

This weather station features enhanced tracking of historical rainfall data. Rain
accumulation data is recorded for today, over all-time, by year, by month, and
by rainfall event.

Press the “RAINFALL” button to review rainfall records. The icon is shown
on the display while historical data is being viewed.

Records are shown in the following order:
PREVIOUS RAINFALL #1*

PREVIOUS RAINFALL #2*
PREVIOUS RAINFALL #3*
CURRENT MONTH TOTAL RAINFALL
PREVIOUS MONTH TOTAL RAINFALL
2 MONTHS AGO TOTAL RAINFALL
CURRENT YEAR TOTAL RAINFALL
PREVIOUS YEAR TOTAL RAINFALL
ALL-TIME TOTAL RAINFALL (date shown is start date of the all-time total;
the date the display was powered on)

RAINFALL

'---TODAY----'
,- PREVIOUS EVENTS--.

RAINFALL

'---TODAY----'
,- PREVIOUS EVENTS--.

1.c'S

ci 9/ ll/ ll

TOTAL RAINFALL TOTAL RAINFALL

FOR DATE SHOWN FOR MONTH SHOWN

RAINFALL

RAINFALL

RAINFALL

'---TODAY----'
,- PREVIOUS EVENTS--.

36.SS TOJALYR.

Cl

CURRENT YEAR

TOTAL RAINFALL

/ ll

I

'---TODAY----'
,- PREVIOUS EVENTS--.

'-18. 13 TOJALYR.

Cl

PREVIOUS YEAR

TOTAL RAINFALL

/ ll

I

'---TODAY----'
,- PREVIOUS EVENTS--.

B'-1.68 ~:-·

Cl

TOTAL RAINFALL

1/ ll

I/

ALL-TIME

*Previous rainfall is the amount of rain recorded from 12:00am to 11:59pm on

the date shown.

13

Weather Ticker

The Weather Ticker automatically ashes your real-time weather information
and alerts as text in the lower part of the display screen.

The possible WEATHER TICKER messages are as follows:

™

HEAT INDEX-XX
WINDCHILL-XX
DEW POINT-XX
IT FEELS LIKE XX OUTSIDE
7 DAY HIGH TEMP. XX- MM/DD
7 DAY LOW TEMP. XX- MM/DD
30 DAY HIGH TEMP. XX- MM/DD
30 DAY LOW TEMP. XX- MM/DD
ALL TIME HIGH TEMP. XXX...RECORDED MM/DD/YY
ALL TIME LOW TEMP. XXX...RECORDED MM/DD/YY
24 HOUR TEMP. CHANGE +XX
ALL TIME HIGH WIND XX MPH...RECORDED MM/DD/YY
7 DAY AVERAGE WIND XX MPH
TODAY’S AVERAGE WIND XX MPH
MOON- NEW
MOON- WAXING CRESCENT
MOON- FIRST QUARTER
MOON- WAXING GIBBOUS
MOON- FULL
MOON- WANING GIBBOUS
MOON- LAST QUARTER
MOON- WANING CRESCENT
INDOOR HUMIDITY OK
INDOOR HUMIDITY HIGH
INDOOR HUMIDITY LOW
NEW LOW TEMP. RECORD XX
NEW HIGH TEMP. RECORD XX
NEW WIND RECORD TODAY XX
CURRENT RAINFALL X.XX/HR.
RAIN EVENT STARTED XX HRS. AGO
SENSOR BATTERIES LOW
DISPLAY BATTERIES LOW
SENSOR SIGNAL LOST...CHECK BATTERIES AND PLACEMENT
CAUTION- HEAT INDEX IS XXX
CAUTION- WIND CHILL IS XXX
CALIBRATION

14

Troubleshooting

Problem Possible Solution

No outdoor sensor

reception

no bars

Tull

Outdoor

temperature

is ashing or

showing dashes

• Relocate the display and/or the 5-in-1 sensor.

The units must be within 330 ft (100 m) of each other.

• Make sure both units are placed at least 3 feet
(.9 m) away from electronics that may interfere with
the wireless communication (such as TVs, microwaves,

computers, etc).

• Use standard alkaline batteries (or lithium batteries
in sensor when temperature is below -4ºF/-20ºC). Do
not use heavy duty or rechargeable batteries. NOTE:
It may take a few minutes for display and sensor to
synchronize after batteries are replaced.

• Synchronize the units:

1. Bring both the sensor and display indoors and

remove power adapter/batteries from each.

2. Reinstall batteries in outdoor sensor.

3. Reinstall power adapter/batteries in display.

4. Let the units sit within a couple feet of each other

for a few minutes to gain a strong connection.

Flashing of the outdoor temperature may be an
indication of wireless interference.

• Make sure the A-B-C switch in the battery
compartments of both the display and sensor are
switched to the same letter. You may choose A, B or
C; but both units must match to sync up. Sometimes
changing to a different channel can help.

Inaccurate forecast

• Weather Forecast icon predicts conditions for the next

12 to 24 hours, not current conditions.

• Has Learning Mode icon disappeared from the
display? Learning Mode must complete before
forecast and pressure will be accurate.

• Allow unit to run continuously for 33 days. Battery
removal or resetting the display will restart Learning
Mode. After 14 days, forecast should be fairly
accurate, however Learning Mode calibrates for a
total of 33 days.

15

Troubleshooting

Problem Possible Solution

Inaccurate

temperature or

humidity

No rainfall

Inaccurate wind

readings

• Make sure both the display and 5-in-1 sensor are

placed away from any heat sources or vents

(see page 10).

• Make sure both units are positioned away from

moisture sources (see page 10).

• Make sure 5-in-1 sensor is mounted at least 5 ft off of

the ground.

• Calibrate indoor and outdoor temperature and

humidity (see page 17).

• Check to ensure the rain gauge stabilizer (plastic tab)

has been removed from the bottom of the sensor (see
page 7).

• Clear debris, such as leaves, out of the rain collector

funnel and debris screen.

• Calibrate the Rain Gauge (see page 18).

• What is wind reading being compared to? Pro

weather stations are typically mounted at 30 ft high

or more. Make sure to compare data using a sensor
positioned at the same mounting height.

• Check location of the sensor. Ensure it’s mounted a

minimum of 5 ft in the air with no obstructions around

it (within several feet).

•Ensure wind cups are spinning freely. If they hesitate

or stop try lubricating with graphite powder or spray
lubricant.

• Check that the batteries are installed correctly.

Batteries may need to be replaced.

Display screen

not working

• Reset the display by pressing and holding the

CLEAR ALL/RESET button, located in the battery
compartment of the display. Date and time will need

to be entered after a reset.

If your AcuRite product does not operate properly after trying
the troubleshooting steps, visit www.AcuRite.com or call
[phone] for assistance.

16

17

BAROMETRIC PRESSURE (must be set to MANUAL mode to calibrate)*

” icon will remain illuminated next to calibrated values.

,.e

INDOOR HUMIDITY
INDOOR TEMPERATURE
OUTDOOR HUMIDITY
OUTDOOR TEMPERATURE

The preference set order is as follows:

preference. The “

3. To save your adjustments, press and release the “ S ET” button to adjust the next

T

“

“ or “

V

V

T

” buttons

V

”, “SE T ”, and “

V

buttons to calibrate the data value higher or lower from the actual reading.

2. To adjust the currently selected (ashing) item, press and release the “

simultaneously for at least 5 seconds.

1. To access calibration mode, press AND HOLD the “
when sensor placement or environmental factors impact the data accuracy.

be calibrated on the display to improve accuracy. Calibration can improve accuracy
The indoor / outdoor temperature and humidity readings, and barometric pressure can

Calibration

or graphite powder on the anemometer for improved movement.

vane and anemometer. If needed, use a small amount of spray lubricant, clear silicone

Remove foreign matter from the outside of the sensor for free movement of the wind

Clean the Wind Vane & Anemometer

collector funnel. Remove from the top by gently squeezing and pulling out.
Remove and empty rain collector debris lter. The debris lter is located in the rain

Clean the Rain Collector Cup

collector cup lls with snow and then melts, it will register as rain on the display.
The 5-in-1 sensor will not be damaged by freezing conditions. NOTE: If the rain

Snow & Freezing Weather

repellent instructions prior to use.
To limit this problem, spray sensor with a household insect repellent. Consult the insect
Insects may cause obstructions and interrupt data by nesting in or on the 5-in-1 sensor.

Insect Prevention

decreased performance and reliability.
polished surfaces of the rain collection funnel or the solar cell. Scratches will result in
Clean with a soft damp cloth. Do not use caustic cleaners or abrasives that will mar the

Clean the Sensor

5-in-1 Sensor Care

from dust, dirt and moisture. Clean ventilation ports regularly with a gentle puff of air.
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep away

Display Care

Care & Maintenance

*To change from AUTO to MANUAL pressure mode and vice versa, press and
HOLD the “SET” button for at least 10 seconds. The display indicates the current
pressure mode selected,“AUTO” or “MANUAL”.

After 20 seconds of inactivity, the display will save the adjustments and exit calibration
mode. Note: Calibrations will be erased if the display is reset or if batteries are
removed and the power adapter is unplugged.

Calibrate the Rain Gauge

The rain gauge on the 5-in-1 sensor can be calibrated to improve accuracy.
Items Needed: 5-in-1 sensor, display unit, plastic cup, pin, screw driver

1. First, ensure 5-in-1 sensor is perfectly level using built-in bubble level.

2. Place display unit close so you can monitor it during calibration.

3. Make a pin hole in the bottom of a plastic cup. Hold the cup over the rain gauge
and ll it with exactly 1 cup (8oz) of water, allowing the water to drip into the rain
gauge. You should hear the internal buckets tip and see water drain through the rain

gauge.

4. A few seconds after each bucket tip, the display unit displays rainfall in
approximately 0.01” or more increments.

5. The cup of water should take more than 20 minutes to empty; a quicker period will
result in inaccurate calibration. Try to simulate a normal steady rainfall. When cup is
empty of water, display unit should register 1.06”

Tips

• There should be nearly an equal number of water drops (about 25 water drops)
between bucket tips. If not, adjust the calibration screws on the bottom of the 5-in-1
sensor until an equal number of water drops are tipping the buckets. Then, restart the
calibration procedure.

• If you don’t hear the buckets tipping and see water dripping alternately out of
each drain, there may be an issue with the rain gauge or it’s adjustment. See
Troubleshooting on page 16.

Adjustment

If the rain gauge doesn’t register close to 1.06”, make an EQUAL adjustment to the two
calibration screws on the bottom of the 5-in-1 sensor. Turning screws clockwise increases
rainfall; counter clockwise decreases rainfall.

• To adjust the rainfall reading by 2% turn both screws 1/8 of a turn.

• To adjust the rainfall reading by 4% turn both screws 1/4 of a turn.

• To adjust the rainfall reading by 8% turn both screws 1/2 of a turn.

Watch the video at www.acurite.com/5n1

18

Specications

TEMPERATURE RANGE

Outdoor: -40ºF to 158ºF; -40ºC to 70ºC
Indoor: 32ºF to 122ºF; 0ºC to 50ºC

HUMIDITY RANGE

Outdoor: 1% to 99%
Indoor: 1% to 99%

WIND SPEED
WIND DIRECTION
INDICATORS

RAINFALL MEASUREMENT
WIRELESS RANGE
OPERATING FREQUENCY
POWER

0 to 99 mph; 0 to 159 kph

16 points

0.01 inches (0.25 mm) and up

330ft / 100m depending on home construction materials
433 MHz

Display: 4.5V, 250mA AC adapter
6 x AA alkaline batteries (optional)

Sensor: 4 x AA alkaline or lithium batteries

DATA REPORTING

Wind Speed: 18 second updates; Direction: 30 seconds
Outdoor temperature & humidity: 36 second updates
Indoor temperature & humidity: 60 second updates

If your AcuRite product does not operate properly,

visit www.AcuRite.com or call [phone] for assistance.

For more information, visit our Knowledge Base at http://www.AcuRite.com/kbase

FCC Information

This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip
ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment.
Such modications could void the user authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.

-

19

Customer Support

Limited 1 Year Warranty

We expressly disclaim all liability for special, consequential,

from any breach of this warranty. Some states do not allow the

Canada, please consult the policies applicable to the country in

dispute relating to this Policy shall be brought exclusively in the

AcuRite customer support is committed to providing you with best-in­class service. For assistance, please have the model number of this

product available and contact us in any of the following ways:

[phone]

Visit us at www.AcuRite.com

► Installation Videos ► Register your Product
► Instruction Manuals ► Support User Forum
► Replacement Parts ► Submit Feedback & Ideas

IMPORTANT

PRODUCT REGISTRATION

Register online

to receive 1 year

warranty protection

www.AcuRite.com

AcuRite is a wholly owned subsidiary of Chaney
Instrument Company. For purchases of AcuRite

products, AcuRite provides the benets and services set

forth herein. For purchases of Chaney products, Chaney

provides the benets and services set forth herein.

We warrant that all products we manufacture under this
warranty are of good material and workmanship and, when
properly installed and operated, will be free of defects for a
period of one year from the date of purchase.

Any product which, under normal use and service, is proven
to breach the warranty contained herein within ONE YEAR
from date of sale will, upon examination by us, and at our sole
option, be repaired or replaced by us. Transportation costs and
charges for returned goods shall be paid for by the purchaser.
We hereby disclaim all responsibility for such transportation
costs and charges. This warranty will not be breached, and we
will give no credit for products which have received normal
wear and tear not affecting the functionality of the product,
been damaged (including by acts of nature), tampered,
abused, improperly installed, or repaired or altered by others
than our authorized representatives.

Remedy for breach of this warranty is limited to repair or
replacement of the defective item(s). If we determine that repair
or replacement is not feasible, we may, at our option, refund
the amount of the original purchase price

THE ABOVE-DESCRIBED WARRANTY IS THE SOLE WARRANTY
FOR THE PRODUCTS AND IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED. ALL OTHER WARRANTIES
OTHER THAN THE EXPRESS WARRANTY SET FORTH HEREIN
ARE HEREBY EXPRESSLY DISCLAIMED, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTY OF MERCHANTABILITY
AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE.

PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE

Archi~ed Products

Register a Product

►

or incidental damages, whether arising in tort or by contract

exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.

We further disclaim liability from personal injury relating to
its products to the extent permitted by law. By acceptance of
any of our products, the purchaser assumes all liability for the

consequences arising from their use or misuse. No person, rm

or corporation is authorized to bind us to any other obligation
or liability in connection with the sale of our products.

Furthermore, no person, rm or corporation is authorized

to modify or waive the terms of this warranty unless done in
writing and signed by a duly authorized agent of ours.

In no case shall our liability for any claim relating to our
products, your purchase or your use thereof, exceed the
original purchase price paid for the product.

Applicability of Policy

This Return, Refund, and Warranty Policy applies only to
purchases made in the United States and Canada. For
purchases made in a country other than the United States or

which you made your purchase.
Additionally, this Policy applies only to the original purchaser

of our products. We do cannot and do not offer any return,
refund, or warranty services if you buy products used or from
resale sites such as eBay or Craigslist.

Governing Law

This Return, Refund, and Warranty Policy is governed by the
laws of the United States and the State of Wisconsin. Any

federal or State courts having jurisdiction in Walworth County,
Wisconsin; and purchaser consents to jurisdiction within the
State of Wisconsin.

20

21

22

23

ACU

►

RITE®

Weather Temperature Weather Kitchen

Stations & Humidity Alert Radio Thermometers

It’s More than Accurate, it’s

AcuRite offers an extensive assortment of precision instruments,

designed to provide you with information you can depend on to

Plan your day with condence

& Timers

ACU RITE.

.

™

Clocks

www.AcuRite.com

©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of

the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copy-

Printed in China

01531DI INST 021116 Visit www.AcuRite.com/patents for details.

rights are the property of their respective owners. AcuRite uses patented technology.