Acura TL 2010 User Manual

Introduction

2010 TL

Congratulations! Your selection of a 2010 Acura TL was a wise investment. It will give you years of driving pleasure.

One of the best ways to enhance the enjoyment of your new vehicle is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner’s manual in your vehicle so youcanrefertoitatanytime.

Several warranties protect your new vehicle. Read the warranty booklet thoroughly so you understand the coverages and are aware of your rights and responsibilities.

Maintaining your vehicle according to the maintenance minder shown in the instrument panel helps to keep your driving trouble-free while it preserves your investment. When your vehicle needs maintenance, keep in mind that your dealer’s staff is specially trained in servicing the many systems unique to your vehicle. Your dealer is dedicated to your satisfaction and will be pleased to answer any questions and concerns.

As you read this manual, you will find inf ormation that is preceded by a symbol. This information is intended to help you avoid damage to your vehicle, other property, or the environment.

Introduction

2010 TL

California Proposition 65 Warning

WARNING:

defects or other reproductive harm.

Event Data Recorders

This vehicle is equipped with one or more devices commonly referred to as event data recorders. These devices record front seat belt use, front passenger seat occupancy, airbag deployment data, and the f ailure of any airbag system component.

except as legally required or with the permission of the vehicle owner.

Service Diagnostic Recorders This vehicle is equipped with service-related devices that record information about powertrain performance. The data can be used to verify emissions law requirements and/or help technicians diagnose and solve service problems. It may also be combined with data f rom other sources for research purposes, but it remains conf idential.

This product contains or emits chemicals known to the State of California to cause cancer and birth

This data belongs to the vehicle owner and may not be accessed by anyone else

AFewWordsAboutSafety

2010 TL

Your safety, and the safety of others, is very important. And operating this vehicle safely is an important responsibility.

To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This inf ormation alerts you to potential hazards that could hurt you or others.

Of course, it is not practical or possible to warn you about all the hazards associated with operating or maintaining your vehicle. You must use your own good judgement.

You will f ind this important safety inf ormation in a variety of forms, including:

−

Safety Labels Safety Messages

three signal words: , , or . These signal words mean:

Safety Headings

Safety Precautions.

Safety Section Instructions

This entire book is f illed with important saf ety information please read it carefully.

on the vehicle.

−

preceded by a safety alert symbol and one of

DANGER WARNING CAUTION

You WILL be KILLED or SERIOUSLY HURT if you don’t follow instructions.

You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions.

You CAN be HURT if you don’t follow instructions.

−

such as Important Safety Reminders or Important

−

such as Driver and Passenger Safety.

−

how to use this vehicle correctly and safely.

−

iii

Owner's Identification Form

2010 TL Online Reference Owner's Manual

2010 TL

Contents

(main controls)

(seat belts, SRS, and child protection)

(indicators,gauges,multi-information display,dashboard,and steering column)

climate control,audio,steering wheel,security,cruise control,HomeLink

Features

Service Information Summary

( )

(fuel, vehicle break-in, and cargo loading)

(engine and transmission operation)

(minder, fluid checking, minor services, and vehicle storage)

(flat tire, jump starting, overheating, and fuses)

(vehicle specifications, tires, and emissions controls)

(how to order)

................................................................................................................................................Index .I

(fluid capacities and tire pressures)

...............................................................................................Your Vehicle at a Glance .3

.......................................................................Before Driving .443

.........................................................................................Driving .459

(warranty and contact inf ormation)

..................................................................................Authorized Manuals (U.S. only) .597

............................................................Driver and Passenger Saf ety .5

.......Instruments and Controls .61

and other convenience items

.................................................Maintenance .495

........................................Taking Care of the Unexpected .545

..............................................Technical Information .575

..............

.......................Warranty and Client Relations (U.S. and Canada only) . 593

215

Overview of Contents

2010 TL

Contents

A convenient reference to the sections in this manual.

Your Vehicle at a Glance

A quick reference to the main controls in your vehicle.

Driver and Passenger Saf ety

Important information about the proper use and care of your vehicle’s seat belts, an overview of the supplemental restraint system, and valuable inf ormation on how to protect children with child restraints.

Instruments and Controls

Explains the purpose of each instrument panel indicator and gauge, the multi-information display, and how to use the controls on the dashboard and steering column.

Features

How to operate the climate control system, the audio system, and other convenience features.

Before Driving

What gasoline to use, how to breakin your new vehicle, and how to load luggage and other cargo.

Driving

The proper way to start the engine, shift the transmission, and park.

Maintenance

The maintenance minder shows you when you need to take your vehicle to the dealer for maintenance service. There is also a list of things to check and instructions on how to check them.

Taking Care of the Unexpected

This section covers several problems motorists sometimes experience, and details how to handle them.

Technical Information

ID numbers, dimensions, capacities, and technical information.

Warranty and Client Relations (U.S. and Canada only)

A summary of the warranties covering your new vehicle, and how to contact us for any reason. Refer to your warranty manual for detailed information.

Authorized Manuals (U.S. only)

How to order manuals and other technical literature.

Index

Service Information Summary

A summary of the information you need when you pull up to the fuel pump.

Your Vehicle at a Glance

2010 TL

INSTRUMENT PANEL INDICATORS GAUGES MULTI-INFORMATION DISPLAY

DRIVER’S FRONT AIRBAG (P.9,26)

MIRROR CONTROLS (P. 162)

DRIVING POSITION MEMORY SYSTEM BUTTONS

POWER DOOR LOCK MASTER SWITCH (P. 146)

POWER WINDOW SWITCHES

TRUNK RELEASE BUTTON

FUEL FILL DOOR RELEASE BUTTON

HOOD RELEASE HANDLE (P. 447)

A/T model with navigation system is shown.

(P. 75)

(P. 164)

(P. 198)

(P. 148)

(P. 445)

USB ADAPTER CABLE (P. 254, 263, 340, 350)

(P. 77)

＊＊: If equipped

HOMELINK BUTTONS (P. 385)

AUXILIARY INPUT

(P. 371)

JACK

MOONROOF SWITCH(P. 63) (P. 202)

ACCESSORY POWER SOCKET

(P. 207)

PASSENGER’S FRONT AIRBAG (P.9,26)

HAZARD WARNING BUTTON (P. 139)

CLIMATE CONTROL SYSTEM (P. 216)

AUDIO CLOCK COMPASS

ACCESSORY POWER SOCKET (P. 207)

AUTOMATIC TRANSMISSION MANUAL TRANSMISSION

(P. 225)

(P. 373)

(P. 378)

(P. 468)

(P. 465)

Your Vehicle at a Glance

2010 TL

HEADLIGHTS/TURN SIGNALS/ FOG LIGHTS

(P. 133, 137)

PADDLE SHIFTERS (P. 473)

＊

INSTRUMENT PANEL BRIGHTNESS (P. 137)

REMOTE AUDIO CONTROL BUTTONS (P. 370)

VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P. 485)

HEADLIGHT WASHERS (P. 132)

＊

HORN

＊

BLUETOOTH HANDSFREELINK SYSTEM VOICE CONTROL BUTTONS (P. 388)

A/T model with navigation system is shown.

＊

To use the horn, press the center pad of the steering wheel. If equipped

＊

Refer to the navigation system owner’s manual.

＊

STEERING WHEEL ADJUSTMENTS

MULTI-INFORMATION DISPLAY BUTTONS (P. 78)

(P. 140)

WINDSHIELD WIPERS/WASHERS

NAVIGATION DISPLAY

PASSENGER AIRBAG OFF INDICATOR

HAZARD WARNING BUTTON

CENTER DISPLAY

REAR WINDOW DEFOGGER/ HEATED MIRROR BUTTON

INTERFACE DIAL SELECTOR KNOB (P. 226)

CRUISE CONTROL BUTTONS

SEAT HEATER SWITCHES

IGNITION SWITCH (P. 145)

(P. 131)

＊

(P. 196)

(P. 34)

(P. 139)

(P. 217, 274)

(P. 139/163)

ENGINE START/ STOP BUTTON (P. 178)

KEYLESS ACCESS REMOTE SLOT (P. 191)

VOICE CONTROL BUTTONS for NAVIGATION SYSTEM / BLUETOOTH HANDSFREELINK

(P. 273)

SYSTEM

(P. 406)

(P. 382)

: Models with keyless access

system

＊

Driver and Passenger Safety

2010 TL

This section gives you important information about how to protect yourself and your passengers. It shows you how to use seat belts. It explains how your airbags work. And it tells you how to properly restrain infants and children in your vehicle.

.........Important Safety Precautions . 6

.......Your Vehicle’s Safety Features . 7

.......................................Seat Belts . 8

...........................................Airbags . 9

.........Protecting Adults and Teens . 11

.....1. Close and Lock the Doors . 11

...........2. Adjust the Front Seats . 13

............3. Adjust the Seat-Backs . 14

...4. Adjust the Head Restraints . 15

5. Fasten and Position the

.............................Seat Belts . 16

6. Maintain a Proper Sitting

................................Position . 18

.....Advice for Pregnant Women . 18

...Additional Safety Precautions . 19

Additional Information About

.......................Your Seat Belts . 20

......................Lap/Shoulder Belt . 21

Automatic Seat Belt

...............................Tensioners . 22

...............Seat Belt Maintenance . 23

Additional Information About

...........................Your Airbags . 24

How Your Front Airbags

.........................................Work . 26

How Your Side Curtain Airbags

.........................................Work . 32

How the Side Airbag Off

......................Indicator Works . 33

How the Passenger Airbag Off

......................Indicator Works . 34

.............................Airbag Service . 35

Protecting Children General

All Children Must Be

−

................................Guidelines . 37

...............................Restrained . 37

..Seat Belt System Components . 20

......Airbag System Components . 24

...How Your Side Airbags Work . 30

..How the SRS Indicator Works . 32

...Additional Safety Precautions . 36

All Children Should Sit in a

.................................Back Seat . 38

The Passenger’s Front Airbag

If You Must Drive with Several

...................................Children . 40

If a Child Requires Close

..................................Attention . 40

Protecting Infants and Small

...................................Children . 42

.......................Protecting Infants . 42

.....................Selecting a Child Seat . 45

....................Installing a Child Seat . 46

...............................With LATCH . 47

..............................With a Tether . 51

...............Checking Seat Belt Fit . 53

..................Using a Booster Seat . 54

When Can a Larger Child Sit in

.........................................Front . 55

.............Carbon Monoxide Hazard . 57

...................................Safety Labels . 58

.........Can Pose Serious Risks . 38

...Additional Safety Precautions . 40

.........Protecting Small Children . 43

.........With a Lap/Shoulder Belt . 49

...........Protecting Larger Children . 53

...Additional Safety Precautions . 56

Driver and Passenger Safety

Important Safety Precautions

2010 TL

recommendations throughout this section, and throughout this manual. Therecommendationsonthispage are the ones we consider to be the most important.

Always Wear Your Seat Belt

A seat belt is your best protection in all types of collisions. Airbags are designed to supplement seat belts, not replace them. So even though your vehicle is equipped with airbags, make sure you and your passengers always wear your seat belts, and wear them properly (see page ).

Restrain All Children

Children age 12 and under should ride properly restrained in a back seat, not the front seat. Infants and smallchildrenshouldberestrained in a child seat. Larger children should use a booster seat and a lap/ shoulder belt until they can use the belt properly without a booster seat

(see pages ).

Be Aware of Airbag Hazards

While airbags can save lives, they can cause serious or fatal injuries to occupants who sit too close to them, or are not properly restrained. Infants, young children, and short adults are at the greatest risk. Be sure to f ollow all instructions and warnings in this manual.

Don’t Drink and Drive

Alcohol and driving don’t mix. Even one drink can reduce your ability to respond to changing conditions, and your reaction time gets worse with every additional drink. So don’t drink and drive, and don’t let your friends drink and drive, either.

Pay Appropriate Attention to the Task of Driving Safely

Engaging in mobile phone conversation or other activities that keep you from paying close attention

−You’ll find many saf ety

37 56

to the road, other vehicles and pedestrians could lead to a crash. Remember, situations can change quickly, and only you can decide when it is safe to divert attention away f rom driving.

Control Your Speed

Excessive speed is a major factor in crash injuries and deaths. Generally, the higher the speed, the greater the risk, but serious injuries can also occur at lower speeds. Never drive faster than is safe for current conditions, regardless of the maximum speed posted.16

Keep Your Vehicle in Safe Condition

Having a tire blowout or a mechanical failure can be extremely hazardous. To reduce the possibility of such problems, check your tire pressures and condition frequently, and perform all regularly scheduled maintenance (see page ).

497

Your Vehicle’s Safety Features

2010 TL

(7)

(10)

(1)

(9)

(8) (9)

(4)

(11)

(5)

(7)

(1) Safety Cage (2) Crush Zones (3) Seats and Seat-Backs (4) Head Restraints

(2)

(5) Collapsible Steering Column (6) Seat Belts (7) Front Airbags (8) Side Airbags (9) Side Curtain Airbags (10) Door Locks (11) Automatic Seat Belt Tensioners

(8)

(3)

(6)

(2)

Your vehicle is equipped with many features that work together to protect you and your passengers during a crash.

Some features do not require any action on your part. These include a strong steel framework that forms a safety cage around the passenger compartment, front and rear crush zones, a collapsible steering column, and tensioners that tighten the front seat belts in a crash.

However, you and your passengers can’t take full advantage of these features unless you remain sitting in the correct position and

your seat belts

features can contribute to injuries if they are not used properly.

The f ollowing pages explain how you cantakeanactiveroleinprotecting yourself and your passengers.

. In fact, some safety

always wear

Driver and Passenger Safety

Your Vehicle’s Safety Features

2010 TL

Seat Belts

Your vehicle is equipped with seat belts in all seating positions.

Your seat belt system also includes an indicator on the instrument panel and a beeper to remind you and your passengers to fasten your seat belts.

Why Wear Seat Belts

Seat belts are the single most effectivesafetydeviceforadultsand larger children. (Infants and smaller children must be properly restrained in child seats.)

Not wearing a seat belt properly increases the chance of serious injury or death in a crash, even though your vehicle has airbags.

In addition, most states and all Canadian provinces and territories require you to wear seat belts.

Not wearing a seat belt properly increases the chance of serious injury or death in a crash, even though your vehicle has airbags.

Be sure you and your passengers always wear seat belts and wear them properly.

When properly worn, seat belts:

Keep you connected to the vehicle so you can take advantage of the vehicle’s built-in safety features.

Help protect you in almost every type of crash, including:

−

frontal impacts

−

side impacts

−

rear impacts

−

rollovers

Help keep you from being thrown against the inside of the vehicle and against other occupants.

Keep you from being thrown out of the vehicle.

Help keep you in a good position should the airbags ever deploy. A good position reduces the risk of injury from an inflating airbag and allows you to get the best advantage from the airbag.

Of course, seat belts cannot completely protect you in every crash.Butinmostcases,seatbelts can reduce your risk of serious injury.

What You Should Do:

Always wear your seat belt, and make sure you wear it properly.

Airbags

2010 TL

Your Vehicle’s Safety Features

Driver and Passenger Safety

Your vehicle has a supplemental restraint system (SRS) with front airbags to help protect the heads and chests of the driver and a front seat passenger during a moderate to severe f rontal collision (see page

for more information on how

your front airbags work).

Your vehicle also has side airbags to help protect the upper torso of the driver or a f ront seat passenger during a moderate to severe side impact (see page f or more information on how your side airbags work).

In addition, your vehicle has side curtain airbags to help protect the heads of the driver, front passenger, and passengers in the outer rear seating positions during a moderate to severe side impact (see page

for more information on how

your side curtain airbags work).

CONTINUED

Your Vehicle’s Safety Features

2010 TL

The most important things you need to know about your airbags are:

Airbags do not replace seat belts.

They are designed to supplement the seat belts.

Airbags off er no protection in rear collisions, or minor frontal or side collisions.

Airbags can pose serious hazards.

To do their job, airbags must inflate with tremendous force. So while airbags help save lives, they can cause minor injuries or more serious or even fatal injuries if occupants are not properly restrained or sitting properly.

What you should do:

your seat belt properly, and sit upright and as far back from the steering wheel as possible while allowing full control of the vehicle. A front passenger should move their seat as far back from the dashboard as possible.

Always wear

The rest of this section gives more detailed inf ormation about how you can maximize your safety.

Remember however, that no safety system can prevent all injures or deaths that can occur in a severe crash, even when seat belts are properly worn and the airbags deploy.

Protecting Adults and Teens

2010 TL

The f ollowing pages provide instructions on how to properly protect the driver, adult passengers and teenage children who are large enough and mature enough to drive or ride in the front seat.

See pages for important

−

37 56

guidelines on how to properly protect infants, small children, and larger children who ride in your vehicle.

Close and Lock the DoorsIntroduction 1.

After everyone has entered the vehicle, be sure the doors are closed and locked.

Your vehicle has a door/

trunk open indicator (red) on the instrument panel to indicate when any door or the trunk lid is not tightly closed.

See page for how to lock the

146

doors, and page for how the door/ trunk open indicator works.

Your vehicle also has a door and trunk open indicator on the multiinformation display to indicate when a specific door or the trunk is not tightly closed. You will see the appropriate indicator(s) for each condition.

You will also hear a beep when you turn the ignition switch to the ON

＊

(II) position, and each time you open any door or the trunk with the key in the ON (II) position.

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and .

17871 181

CONTINUED

Driver and Passenger Safety

Protecting Adults and Teens

2010 TL

If any door or the trunk is not closed tightly, the multi-information display reminds you to close the open door(s) or the trunk bef ore you start driving.

The above illustration shows that all doors and the trunk are open.

When the trunk is not tightly closed, the ‘‘TRUNK OPEN’’ indicator will come on.

When one or more doors or the trunk lid are not tightly closed, the corresponding indicator for each condition will come on.

Theaboveexampleshowsthefront right and rear left doors, and the trunk open.

Protecting Adults and Teens

2010 TL

Locking the doors reduces the chance of someone being thrown out of the vehicle during a crash, and it helps prevent passengers from accidentally opening a door and falling out.

Locking the doors also helps prevent an outsider f rom unexpectedly opening a door when you come to a stop.

Your vehicle has the auto door locking/unlocking feature. For more information, see page .

121

Adjust the Front Seats2.

Adjust the driver’s seat as far to the rear as possible while allowing you to maintain f ull control of the vehicle. Have a f ront passenger adjust their seat as far to the rear as possible.

If you sit too close to the steering wheel or dashboard, you can be seriously injured by an inflating front airbag, or by striking the steering wheel or dashboard.

The National Highway Traffic Safety Administration and Transport Canada recommend that drivers allow at least 10 inches (25 cm) between the center of the steering wheel and the chest. In addition to adjusting the seat, you can adjust the steering wheel up and down, and in and out (see page ).

If you cannot get f ar enough away from the steering wheel and still reach the controls, we recommend that you investigate whether some type of adaptive equipment may help.

140

CONTINUED

Driver and Passenger Safety

Protecting Adults and Teens

2010 TL

Adjust the Seat-Backs3.

Sitting too close to a front airbag can result in serious injury or death if the front airbags inflate.

Always sit as far back from the front airbags as possible.

See page for how to adjust the front seats.

155

Reclining the seat-back too far can result in serious injury or death in a crash.

Adjust the seat-back to an upright position, and sit well back in the seat.

Adjust the driver’s seat-back to a comfortable, upright position, leaving ample space between your chest and the airbag cover in the center of the steering wheel.

Passengers with adjustable seatbacks should also adjust their seatback to a comfortable, upright position.

Protecting Adults and Teens

2010 TL

Reclining a seat-back so that the shoulder part of the belt no longer rests against the occupant’s chest reduces the protective capability of the belt. It also increases the chance of sliding under the belt in a crash and being seriously injured. The farther a seat-back is reclined, the greater the risk of injury.

See page for how to adjust the seat-backs.

155

Adjust the Head Restraints4.

Adjust the driver’s head restraint so the center of the back of your head rests against the center of the restraint.

Have passengers adjust their head restraints properly as well. Taller persons should adjust their restraint as high as possible.

Improperly positioning head restraints reduces their effectiveness and you can be seriously injured in a crash.

Make sure head restraints are in place and positioned properly before driving.

CONTINUED

Driver and Passenger Safety

Protecting Adults and Teens

2010 TL

Properly adjusted head restraints will help protect occupants from whiplash and other crash injuries.

See page for how to adjust the head restraints and how the driver’s and front passenger’s active head restraints work.

157

Fasten and Position the Seat

Belts

Insert the latch plate into the buckle, then tug on the belt to make sure the belt is securely latched. Check that the belt is not twisted, because a twisted belt can cause serious injuries in a crash.

Position the lap part of the belt as low as possible across your hips, then pull up on the shoulder part of thebeltsothelappartfitssnugly. This lets your strong pelvic bones take the force of a crash and reduces the chance of internal injuries.

Protecting Adults and Teens

2010 TL

If necessary, pull up on the belt again to remove any slack, then check that the belt rests across the center of your chest and over your shoulder. This spreads the forces of a crash over the strongest bones in your upper body.

Improperly positioning the seat belts can cause serious injury or death in a crash.

Make sure all seat belts are properly positioned before driving.

If the seat belt touches or crosses your neck, or if it crosses your arm instead of your shoulder, you need to adjust the seat belt anchor height.

RELEASE BUTTON

The front seats have adjustable seat belt anchors. To adjust the height of an anchor, press and hold the release button and slide the anchor up or down as needed (it has four positions).

Never place the shoulder portion of a lap/shoulder belt under your arm or behind your back.

very serious injuries in a crash.

If a seat belt does not seem to work properly, it may not protect the occupant in a crash.

No one should sit in a seat with an inoperative seat belt.

belt that is not working properly can result in serious injury or death. Have your dealer check the belt as soon as possible.

See page f or additional information about your seat belts and how to take care of them.

This could cause

Using a seat

Driver and Passenger Safety

Protecting Adults and Teens

2010 TL

6. Position

After all occupants have adjusted their seats and head restraints, and put on their seat belts, it is very important that they continue to sit upright, well back in their seats, with their feet on the floor, until the vehicle is safely parked and the engine is off.

Sitting improperly can increase the chance of injury during a crash. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased.

In addition, an occupant who is out of position in the f ront seat can be seriously or f atally injured in a crash by striking interior parts of the vehicle or being struck by an inflating front airbag.

Sitting improperly or out of position can result in serious injury or death in a crash.

Always sit upright, well back in the seat, with your feet on the floor.

Advice for Pregnant WomenMaintain a Proper Sitting

If you are pregnant, the best way to protect yourself and your unborn child when driving or riding in a vehicle is to always wear a seat belt, and keep the lap part of the belt as low as possible across the hips.

Protecting Adults and Teens

2010 TL

When driving, remember to sit upright and adjust the seat as far back as possible while allowing full control of the vehicle. When riding as a front passenger, adjust the seat as far back as possible.

This will reduce the risk of injuries to both you and your unborn child that can be caused by a crash or an inflating front airbag.

Each time you have a checkup, ask your doctor if it’s okay for you to drive.

Additional Safety Precautions

Two people should never use the same seat belt.

If they do, they could be very seriously injured in a crash.

Do not put any accessories on seat belts.

Devices intended to improve occupant comfort or reposition the shoulder part of a seat belt can reduce the protective capability of thebeltandincreasethechanceof serious injury in a crash.

Do not place hard or sharp objects between yourself and a front airbag.

Carrying hard or sharp objects on your lap, or driving with a pipe or other sharp object in your mouth, can result in injuries if your airbags inflate.

Do not attach or place objects on the f ront airbag covers.

Objects on the covers marked ‘‘SRS AIRBAG’’ could interf ere with the proper

operation of the airbags or be propelled inside the vehicle and hurt someone if the airbags inflate.

Keep your hands and arms away from the airbag covers.

If your hands or arms are close to an airbag cover, they could be injured if the airbags inf late.

Do not attach hard objects on or near a door.

If a side airbag or a side curtain airbag inflates, a cup holder or other hard object attached on or near the door could be propelled inside the vehicle and hurt someone.

Do not cover or replace front seatback covers without consulting your dealer.

Improperly replacing or covering front seat-back covers can prevent your side airbags from inflating during a side impact.

Driver and Passenger Safety

Additional Information About Your Seat Belts

2010 TL

Seat Belt System Components

Your seat belt system includes lap/ shoulder belts in all seating positions. The front seat belts are also equipped with automatic seat belt tensioners.

This system uses the same sensors as the front airbags to monitor whether the front seat belts are latched or unlatched, and how much weight is on the front passenger’s seat (see pages and ).

28 29

The seat belt system

includes an indicator on the instrument panel and a beeper to remind you and your passengers to fasten your seat belts.

This system monitors the front seat belts. If you turn the ignition switch to the ON (II) position before your seat belt is fastened, the beeper will sound and the indicator will flash. If your seat belt is not fastened before the beeper stops, the indicator will stop flashing but remain on.

BELT’’ message on the multiinformation display.

If a front passenger does not fasten their seat belt, the indicator will come on about 6 seconds after the ignition switch is turned to the ON

＊

(II) position.

If either the driver or a front passenger does not fasten their seat belt while driving, the beeper will sound and the indicator will f lash again at regular intervals.

You will also see a ‘‘FASTEN SEAT

＊

BELT’’ or ‘‘FASTEN PASSENGER SEAT BELT’’ message on the multiinformation display.

When no one is sitting in the front passenger’s seat, or a child or small adult is riding there, the indicator should not come on and the beeper should not sound.You will also see a ‘‘FASTEN SEAT

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and .

178 181

Additional Information About Your Seat Belts

2010 TL

If the indicator comes on or the beeper sounds when the driver’s seat belt is latched and there is no front seat passenger and no items on the front seat, something may be interfering with the monitoring system. Look f or and remove:

Any items under the f ront passenger’s seat.

Any object(s) hanging on the seat or in the seat-back pocket.

Any object(s) touching the rear of the seat-back.

If no obstructions are found, have your vehicle checked by a dealer.

Lap/Shoulder Belt

The lap/shoulder belt goes over your shoulder, across your chest, and across your hips.

To fasten the belt, insert the latch plate into the buckle, then tug on the belt to make sure the buckle is latched (see page for how to properly position the belt).

To unlock the belt, press the red PRESSbuttononthebuckle.Guide the belt across your body so that it retracts completely. Af ter exiting the vehicle, be sure the belt is out of the way and will not get closed in the door.

All seat belts have an emergency locking retractor. In normal driving, the retractor lets you move freely in your seat while it keeps some tension on the belt. During a collision or sudden stop, the retractor automatically locks the belt to help restrain your body.

The seat belts in all positions except the driver’s have a lockable retractor that must be activated to secure a child seat (see page ).

If the shoulder part of the belt is pulled all the way out, the lockable retractor will activate. The belt will retract, but it will not allow the passenger to move freely.

CONTINUED

Driver and Passenger Safety

Additional Information About Your Seat Belts

2010 TL

To deactivate the lockable retractor, unlatch the buckle and let the seat belt fully retract. To refasten the seat belt, pull it out only as far as needed.

Automatic Seat Belt Tensioners

For added protection, the front seat belts are equipped with automatic seat belt tensioners. When activated, the tensioners immediately tighten the belts to help hold the driver and a front passenger in position.

The tensioners are designed to activate in any collision severe enough to cause the front airbags to deploy.

If a side curtain airbag deploys during a side impact, the tensioner on that side of the vehicle will also deploy.

The tensioners can also be activated during a collision in which the front airbags . In this case, the airbags would not be needed, but the extra tension in the seat belt could be helpful.

When the tensioners are activated, the seat belts will remain tight until they are unbuckled.

do not deploy

Additional Information About Your Seat Belts

2010 TL

Seat Belt Maintenance

For safety, you should check the condition of your seat belts regularly.

Pull each belt out fully, and look for frays, cuts, burns, and wear. Check that the latches work smoothly and the belts retract easily. If a belt does not retract easily, cleaning the belt may correct the problem (see page

). Any belt that is not in good

530

condition or working properly will not provide good protection and should be replaced as soon as possible.

Acura provides a limited warranty on seat belts. See your

Information

booklet for details.

Acura Warranty

If a seat belt is worn during a crash, it must be replaced by your dealer. A belt that has been worn during a crash may not provide the same level of protection in a subsequent crash.

The dealer should also inspect the anchors for damage and replace them if needed. If the automatic seat belt tensioners activate during a crash, they must be replaced.

Not checking or maintaining seat belts can result in serious injury or death if the seat belts do not work properly when needed.

Check your seat belts regularly and have any problem corrected as soon as possible.

Driver and Passenger Safety

Additional Information About Your Airbags

2010 TL

Airbag System Components

(1)

(8)

(1) Driver’s Front Airbag (2) Passenger’s Front Airbag (3) Control Unit (4) Front Seat Belt Tensioners (5) Side Airbags (6) Driver’s Seat Position Sensor (7) Front Passenger’s Weight Sensors (8) Front Impact Sensors (9) Passenger Airbag Off Indicator (10) Side Impact Sensors (First) (11) Occupant Detection System (ODS) Sensors (12) Front Passenger’s Weight Sensors Control Unit/

ODS Sensors Control Unit (13) Side Impact Sensors (Second) (14) Side Curtain Airbags (15) Supplemental Restraint System (SRS) Indicator (16) Safing Sensor

(3)

(15)

(6)

(8)

(10)

(9) (2)

(4)

(11) (5)

(5)

(13)

(7)

(14)

(10)

(13)

(14)

(7)

(16)

(12)

Additional Information About Your Airbags

2010 TL

Your airbag system includes:

Two SRS (supplemental restraint system) front airbags. The driver’s airbag is stored in the center of the steering wheel; the front passenger’sairbagisstoredinthe dashboard. Both are marked ‘‘SRS AIRBAG’’ (see page ).

Two side airbags, one for the driver and one for a front passenger. The airbags are stored in the outer edges of the seatbacks. Both are marked ‘‘SIDE AIRBAG’’ (see page ).

Two side curtain airbags, one f or each side of the vehicle. The airbags are stored in the ceiling, above the side windows. The f ront and rear pillars are marked ‘‘SIDE CURTAIN AIRBAG’’ (see page

Automatic front seat belt tensioners (see page ).

Sensors that can detect a moderate to severe front impact or side impact.

Sensors that can detect whether a child is in the passenger’s side airbag path and signal the control unit to turn the airbag off (see page ).

Sensors that can detect whether the driver’s seat belt and the front passenger’s seat belt are latched or unlatched (see page ).

A driver’s seat position sensor that monitors the distance of the seat from the front airbag. If the seat is too far forward, the airbag will inflate with less force (see page

Weight sensors that monitor the weight on the front passenger’s seat. If the weight is about 65 lbs (29 kg) or less (the weight of an infant or small child), the passenger’s front airbag will be turned off (see page ).

CONTINUED

Driver and Passenger Safety

Additional Information About Your Airbags

2010 TL

A sophisticated electronic system that continually monitors and records information about the sensors, the control unit, the airbag activators, the seat belt tensioners, and driver and front passenger seat belt use when the ignition switch is in the ON (II) position.

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and .

178 181

＊

An indicator on the instrument panel that alerts you to a possible problem with your airbags, sensors, or seat belt tensioners (see page ).

An indicator on the instrument panel that alerts you that the passenger’s side airbag has been turned off (see page ).

An indicator on the dashboard that alerts you that the passenger’s front airbag has been turned off (see page ).

Emergency backup power in case your vehicle’s electrical system is disconnected in a crash.

How Your Front Airbags Work

If you ever have a moderate to severe f rontal collision, sensors will detect the vehicle’s rapid deceleration.

If the rate of deceleration is high enough, the control unit will inf late the driver’s and front passenger’s airbags, at the time and with the force needed.

Additional Information About Your Airbags

2010 TL

During a frontal crash, your seat belt restrains your lower body and torso, and the f ront airbag helps protect your head and chest.

Although both airbags normally inflate within a split second of each other, it is possible for only one airbag to deploy.

This can happen if the severity of a collision is at the margin, or threshold, that determines whether or not the airbags will deploy. In such cases, the seat belt will provide sufficient protection, and the supplemental protection offered by the airbag would be minimal.

Only the driver’s airbag can deploy if there is no passenger in the front seat, or if the advanced airbag system has turned the passenger’s airbag off (see page ).34

After inf lating, the front airbags immediately deflate, so they won’t interfere with the driver’s visibility, or the ability to steer or operate other controls.

The total time for inflation and deflation is one-tenth of a second, so fast that most occupants are not aware that the airbags deployed until they see them lying in their laps.

After a crash, you may see what looks like smoke. This is actually powder from the airbag’s surface. Although the powder is not harmful, people with respiratory problems mayexperiencesometemporary discomfort. If this occurs, get out of the vehicle as soon as it is safe to do so.

CONTINUED

Driver and Passenger Safety

Additional Information About Your Airbags

2010 TL

Dual-Stage Airbags

Your front airbags are dual-stage airbags. This means they have two inflation stages that can be ignited sequentially or simultaneously, depending on crash severity.

more severe

In a crash, both stages will ignite simultaneously to provide the quickest and greatest protection.

less severe

In a crash, one stage will ignite first, then the second stage will ignite a split second later. This provides longer airbag inflation time with a little less force.

Your front airbags are also dualthreshold airbags. Airbags with this feature have two deployment thresholds that depend on whether sensors detect the occupant is wearing a seat belt or not.

If the occupant’s belt is , the airbag will deploy at a slightly lower threshold, because the occupant would need extra protection.

If the occupant’s belt is , the airbag will inf late at a slightly higher threshold, when the airbag would be needed to supplement the protection provided by the seat belt.

not latched

latched

Advanced AirbagsDual-Threshold Airbags

Your front airbags are also advanced airbags. The main purpose of this feature is to help prevent airbagcaused injuries to short drivers and children or small-statured adults who ride in front.

For both advanced airbags to work properly:

Occupants must sit upright and wear their seat belts properly.

Do not spill any liquids on or under the seats, cover the sensors, or put any cargo or metal objects under the f ront seats.

Failure to follow these instructions could damage the sensors or prevent them from working properly.

Additional Information About Your Airbags

2010 TL

Be aware that objects placed on the passenger’s seat can also cause the airbag to be turned off.

When the passenger airbag gets turned off by the weight sensors, a ‘‘passenger airbag off’’ indicator in the center of the dashboard comes on (see page ).

Driver and Passenger Safety

DRIVER’S SEAT POSITION SENSOR

The driver’s advanced front airbag system includes a seat position sensor under the seat. If the seat is too far forward, the airbag will inflate with less force, regardless of the severity of the impact.

If there is a problem with the sensor, the SRS indicator will come on, and the airbag will inflate in the normal manner regardless of the driver’s seating position.

PASSENGER’S SEAT WEIGHT SENSOR

The passenger’s advanced f ront airbag system has weight sensors under the seat. Although Acura does not encourage carrying an infant or small child in front, if the sensors detect the weight of an infant or small child (up to about 65 lbs or 29 kg), the system will automatically turn the passenger’s front airbag off.

If the weight sensors detect there is no passenger in the front seat, the airbag is automatically turned off. However, the passenger airbag off indicator in this situation will not come on.

CONTINUED

Additional Information About Your Airbags

2010 TL

To ensure that the passenger’s advanced front airbag system will work properly,

that would increase or decrease the weight on the front passenger’s seat.

This includes:

A rear passenger pushing or pulling on the back of the f ront passenger’s seat.

Moving the front seat or seat-back forcibly back against cargo on the seat or f loor behind it.

Hanging heavy items on the f ront passenger seat, or placing heavy items in the seat-back pocket.

do not do anything

Back seat passengers should not wedge objects or intentionally force their f eet under the front passenger seat.

Also,makesurethefloormat behind the front passenger’s seat is hooked to the floor mat anchor (see page ). If it is not, the mat may interfere with the proper operation of the sensors and operation of the seat.

529

How Your Side Airbags Work

If you ever have a moderate to severe side impact, sensors will detect rapid acceleration and signal the control unit to instantly inf late either the driver’s or the passenger’s side airbag.

Additional Information About Your Airbags

2010 TL

Only one airbag will deploy during a side impact. If the impact is on the passenger’s side, the passenger’s side airbag will deploy even if there is no passenger.

To get the best protection from the side airbags, front seat occupants should wear their seat belts and sit upright and well back in their seats.

Side Airbag Cutoff System

Your vehicle has a side airbag cutof f system designed primarily to protect a child riding in the f ront passenger’s seat.

children to ride in front, if the position sensors detect a child has leaned into the side airbag’s deployment path, the airbag will shut off.

Thesideairbagmayalsoshutoffifa short adult leans sideways, or a larger adult slouches and leans sideways into the airbag’s deployment path.

Objects placed on the front passenger seat can also cause the side airbag to be shut off.

If the side airbag off indicator comes on (see page ), have the passenger sit upright. Once the passenger is out of the airbag’s deployment path, the system will turn the airbag back on, and the indicator will go out.Although Acura does not encourage

There will be some delay between the moment the passenger moves into or out of the airbag deployment pathandwhentheindicatorcomes on or goes off.

A front seat passenger should not use a cushion or another object as a backrest. It may prevent the cutoff system f rom working properly.

Driver and Passenger Safety

Additional Information About Your Airbags

2010 TL

How Your Side Curtain Airbags Work

SIDE CURTAIN AIRBAG

In a moderate to severe side impact, sensors will detect rapid acceleration and signal the control unit to instantly inflate the side curtain airbag and activate the seat belt tensioner on the driver’s or the passenger’s side of the vehicle.

If the impact is on the passenger’s side, the passenger’s side curtain airbag will inflate even if there are no occupants on that side of the vehicle.

One or both side curtain airbags may inflate in a moderate to severe frontal collision which causes the front airbags to deploy.

To get the best protection from the side curtain airbags, occupants should wear their seat belts and sit upright and well back in their seats.

How the SRS Indicator Works

The SRS indicator alerts you to a potential problem with your airbags or seat belt tensioners.

When you turn the ignition switch

＊

to the ON (II) position, this indicator comes on briefly then goes off. This tells you the system is working properly.

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and .

178 181

Additional Information About Your Airbags

2010 TL

If the indicator comes on at any other time, or does not come on at all, you should have the system checked by your dealer. For example:

If the SRS indicator does not come on after you turn the ignition switch to the ON (II) position or on models with keyless access system, press the engine start/ stop button to set ON mode (see page ).

181

If the indicator stays on after the engine starts.

If the indicator comes on or flashesonandoffwhileyoudrive.

You will also see a ‘‘CHECK AIRBAG SYSTEM’’ message on the multi-information display.

If you see any of these indications, the airbags and seat belt tensioners may not work properly when you need them.

Ignoring the SRS indicator can result in serious injury or death if the airbag systems or tensioners do not work properly.

Have your vehicle checked by a dealer as soon as possible if the SRS indicator alerts you to a possible problem.

U. S. Canada

How the Side Airbag Off Indicator Works

This indicator alerts you that the passenger’s side airbag has been automatically shut off. It does

not

mean there is a problem with your side airbags.

When you turn the ignition switch

＊

to the ON (II) position, the indicator should come on briefly and then go out(seepage ).Ifitdoesn’tcome

on, stays on, or comes on while driving without a passenger in the front seat, have the system checked.

You will also see a ‘‘PASSENGER SIDE AIRBAG OFF’’ message on the multi-information display.

CONTINUED

Driver and Passenger Safety

Additional Information About Your Airbags

2010 TL

＊ Be aware that objects placed on the

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and .

178 181

How the Passenger Airbag Off Indicator Works

U. S. Canada

PASSENGER AIRBAG OFF INDICATOR

This indicator alerts you that the passenger’s front airbag has been shut off because weight sensors detect about 65 lbs (29 kg) or less (the weight of an infant or small child) on the front passenger’s seat. It does there is a problem with the airbag.

not mean

front seat can cause the indicator to come on.

If no weight is detected on the f ront seat, the airbag will be automatically shut off. However, the indicator will not come on.

The passenger airbag of f indicator may come on and off repeatedly if the total weight on the seat is near the airbag cutoff threshold.

If an adult or teenage passenger is riding in front, move the seat as far to the rear as possible, and have the passenger sit upright and wear the seat belt properly.

Additional Information About Your Airbags

2010 TL

If the indicator comes on with no front seat passenger and no objects on the seat, or with an adult riding there, something may be interfering with the weight sensors. Look for and remove:

Any items under the f ront passenger’s seat.

Any object hanging on the seat or in the seat-back pocket.

Any object(s) touching the rear of the seat-back.

If no obstructions are found, have your vehicle checked by a dealer as soon as possible.

Airbag Service

Your airbag systems are virtually maintenance free, and there are no parts you can safely service. However, you must have your vehicle serviced if:

An airbag ever inflates.

that has deployed must be replaced along with the control unit and other related parts. Any seat belt tensioner that activates must also be replaced.

Do not try to remove or replace anyairbagbyyourself.Thismust be done by an authorized dealer or a knowledgeable body shop.

Any airbag

The SRS indicator alerts you to a problem.

authorized dealer as soon as possible. If you ignore this indication, your airbags may not operate properly.

If your vehicle has a moderate to severe impact.

airbags do not inflate, your dealer should inspect the driver’s seat position sensor, the front passenger’s weight sensors, the front seat belt tensioners, and all seat belts and their anchors worn during a crash to make sure they are operating properly.

Take your vehicle to an

Even if your

Driver and Passenger Safety

Additional Information About Your Airbags

2010 TL

Additional Safety Precautions

Donotattempttodeactivateyour airbags.

seat belts provide the best protection.

Do not tamper with airbag components or wiring for any reason.

the airbags to deploy, possibly causing very serious injury.

Do not expose the f ront passenger’s seat-back to liquid.

another liquid soaks into a seatback, it can prevent the side airbag cutoff system from working properly.

Together, airbags and

Tampering could cause

If water or

Do not remove or modif y a front seat without consulting your dealer.

driver’s seat position sensor or the front passenger’s weight sensors ineffective. If it is necessary to remove or modif y a front seat to accommodate a person with disabilities, first contact Acura Client Services at 800-382-2238.

This could make the

Children depend on adults to protect

2010 TL

them. However, despite their best intentions, many adults do not know how to protect child passengers.

If you have children, or ever need to drive with a child in your vehicle, be sure to read this section. It begins with important general guidelines, then presents special information for infants, small children, and larger children.

properly

Protecting Children General Guidelines

All Children Must Be Restrained

Each year, many children are injured or killed in vehicle crashes because they are either unrestrained or not properly restrained. In f act, traffic accidents are the number one cause of death of children age 12 and under.

To reduce the number of child deaths and injuries, every state, Canadian province and territory requires that infants and children be properlyrestrainedwhentheyridein a vehicle.

Infants and small children must be restrained in an approved child seat that is properly secured to the vehicle

(see pages ).

−

42 52

−

Children who are unrestrained or improperly restrained can be seriously injured or killed in a crash.

Any child too small for a seat belt should be properly restrained in a child seat. A larger child should be properly restrained with a seat belt and use a booster seat if necessary.

Larger children must be restrained with a lap/shoulder belt and ride on a booster seat until the seat belt f its them properly

(see pages ).

−

53 56

Driver and Passenger Safety

Protecting Children General Guidelines

2010 TL

−

All Children Should Sit in a Back Seat

According to accident statistics, children of all ages and sizes are safer when they are restrained in a back seat.

The National Highway Traffic Safety Administration and Transport Canada recommend that all children age 12 and under be properly restrained in a back seat. Some states have laws restricting where children may ride.

Children who ride in the back are less likely to be injured by striking interior vehicle parts during a collision or hard braking. Also, children cannot be injured by an inflating front airbag when they ride in the back.

The Passenger’s Front Airbag Can Pose Serious Risks

Front airbags have been designed to help protect adults in a moderate to severe f rontal collision. To do this, the passenger’s front airbag is quite large, and it can inflate with enough force to cause very serious injuries.

advanced front airbag system that automatically turns the passenger’s front airbag off under certain circumstances (see page ), please follow these guidelines:

Infants Never put a rear-facing child seat in the front seat of a vehicle equipped with a passenger’s front airbag.

the airbag inflates, it can hit the back of the child seat with enough force to kill or very seriously injure an infant.

Small Children Placing a f orward-facing child seat in the front seat of a vehicle equipped with a passenger’s front airbag can be hazardous.

too far forward, or the child’s head is thrown f orward during a collision, an inflating front airbag can strike the child with enough force to kill or very seriously injure a small child.Even though your vehicle has an

Larger Children Children who have outgrown child seats are also at risk of being injured or killed by an inflating passenger’s front airbag.

larger children should sit in the back seat, on a booster seat if needed, and be properly restrained with a seat belt (see page for important information about protecting larger children).

If the vehicle seat is

Whenever possible,

Protecting Children General Guidelines

2010 TL

−

To remind you of the passenger’s front airbag hazards, and that children must be properly restrained in a back seat, your vehicle has warninglabelsonthedashboard (U.S. models) and on the front visors. Please read and follow the instructions on these labels.

U.S. Models

SUN VISOR

Canadian Models

SUN VISOR

DASHBOARD

Driver and Passenger Safety

Protecting Children General Guidelines

2010 TL

−

If You Must Drive with Several Children

Your vehicle has a back seat where children can be properly restrained. If you ever have to carry a group of children, and a child must ride in front:

Place the largest child in the front seat, provided the child is large enough to wear the lap/shoulder belt properly (see page ).

Move the vehicle seat as far to the rear as possible (see page ).

Have the child sit upright and well backintheseat(seepage ).

Make sure the seat belt is properly positioned and secured (see page

155

If a Child Requires Close Attention

Many parents say they prefer to put an infant or a small child in the f ront passenger seat so they can watch the child, or because the child requires attention.

Placing a child in the front seat exposes the child to hazards in a frontal collision, and paying close attention to a child distracts the driver from the important tasks of driving, placing both of you at risk.

If a child requires close physical attention or frequent visual contact, we strongly recommend that another adult ride with the child in the back seat. The back seat is far safer for a child than the front.

Additional Safety Precautions

Neverholdaninfantorchildon your lap.

seat belt in a crash, you could be thrown forward and crush the child against the dashboard or a seat-back. If you are wearing a seat belt, the child can be torn from your arms and be seriously hurt or killed.

Never put a seat belt over yourself and a child.

belt could press deep into the child and cause serious or fatal injuries.

Never let two children use the same seat belt.

could be very seriously injured in a crash.

Use the childproof door locks to prevent children from opening the rear doors.

children from accidentally falling out (see page ).

If you are not wearing a

During a crash, the

If they do, they

This can prevent

147

Protecting Children General Guidelines

2010 TL

−

Make sure any unused seat belt that a child can reach is buckled, the lockable retractor is activated, and the belt is fully retracted and locked.

If a child wraps a loose seat belt around their neck, they can be seriously or fatally injured. (See pages and for how to

50 51

activate and deactivate the lockable retractor.)

Do not leave children alone in a vehicle.

Leaving children without adult supervision is illegal in most states, Canadian provinces and territories, and can be very hazardous.

For example, infants and small childrenleftinavehicleonahot day can die from heatstroke. A child left alone with the key in the ignition switch or with the keyless access remote in the vehicle can accidentally set the vehicle in motion, possibly injuring

themselves or others.

Lock all doors and the trunk when your vehicle is not in use.

Children who play in vehicles can accidentally get trapped inside. Teach your children not to play in or around vehicles. Know how to operate the emergency trunk opener and decide if your children should be shown how to use this feature(seepage ).

Keep vehicle keys/remote transmitters or keyless access remotes out of the reach of children.

Even very young

150

children learn how to unlock vehicle doors, turn on the ignition

＊

switch , and open the trunk, which can lead to accidental injury or death.

On models with keyless access

＊

system

Your vehicle has the engine start/stop button instead of an ignition switch. For more information on selecting the power mode, see page .

Driver and Passenger Safety

178

Protecting Infants and Small Children

2010 TL

Protecting Infants

Child Seat Type

An infant must be properly restrained in a rear-facing, reclining child seat until the child reaches the seat maker’s weight or height limit for the seat, and the child is at least one year old.

Only a rear-facing child seat provides proper support for a baby’s head, neck, and back.

Two types of seats may be used: a seat designed exclusively for infants, or a convertible seat used in the rearfacing, reclining mode.

Do not put a rear-f acing child seat in a forward-facing position.

facing forward, an infant could be very seriously injured during a frontal collision.

If placed

Rear-f acing Child Seat Placement

A rear-facing child seat can be placed in any seating position in the back seat, but not in the front.

rear-f acing child seat in the f ront seat.

If the passenger’s front airbag inflates, it can hit the back of the child seat with enough force to kill or seriously injure an inf ant.

When properly installed, a rearfacing child seat may prevent the driver or a f ront passenger from moving their seat as far back as recommended, or f rom locking their seat-back in the desired position.

It can also interfere with proper operation of the passenger’s advanced front airbag system.

Never put a

Protecting Infants and Small Children

2010 TL

In any of these situations, we strongly recommend that you install the child seat directly behind the front passenger’s seat, move the seat as far forward as needed, and leave it unoccupied. Or, you may wish to get a smaller rear-facing child seat.

Placing a rear-facing child seat in the front seat can result in serious injury or death during a crash.

Always place a rear-facing child seat in the back seat, not the front.

Protecting Small Children

Child Seat Type

Many states, Canadian provinces and territories allow a child one year of age or older who also meets the minimum size and weight requirements to transition from a rear-facing child seat to a forward facing seat. Know the requirements where you are driving and follow the child seat instructions. Many experts recommend use of a rear-f acing seat up to age two, if the child’s height

and weight are appropriate for a rear-facing seat.

Of the different seats available, we recommend those that have a fivepoint harness system as shown.

We also recommend that a small child use the child seat until the child reaches the weight or height limit for the seat.

CONTINUED

Driver and Passenger Safety

Protecting Infants and Small Children

2010 TL

Child Seat Placement

We strongly recommend placing a forward-facing child seat in a back seat, not the front.

Placing a f orward-facing child seat in the front seat of a vehicle equipped with a passenger’s airbag can be hazardous.

far forward, or the child’s head is thrown f orward during a collision, an inflating airbag can strike the child with enough force to cause very serious or fatal injuries.

If the vehicle seat is too

Even with advanced front airbags that automatically turn the passenger’s front airbag off (see page ), a back seat is the safest

place for a small child.

If it is necessary to put a f orwardfacing child seat in the front, move the vehicle seat as far to the rear as possible, and be sure the child seat is firmly secured to the vehicle and the child is properly strapped in the seat.

Placing a forward-facing child seat in the front seat can result in serious injury or death if the front airbag inflates.

Ifyoumustplaceaforwardfacing child seat in front, move the vehicle seat as far back as possible, and properly restrain the child.

When buying a child seat, you need

2010 TL

to choose either a conventional child seat, or one designed for use with the Lower Anchors and Tethers for CHildren (LATCH) system.

Conventional child seats must be secured to a vehicle with a seat belt, whereas LATCH-compatible seats are secured by attaching the seat to hardware built into the two outer seating positions in the back seat.

Since LATCH-compatible child seats are easier to install and reduce the possibility of improper installation, we recommend selecting this style.

In seating positions and vehicles not equipped with LATCH, a LATCHcompatible child seat can be installed using a seat belt.

Whatever type of seat you choose, to provide proper protection, a child seat should meet three requirements:

The child seat should meet

1. Federal Motor Vehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213.

Look f or FMVSS 213 or CMVSS 213 on the box.

The child seat should be of the

2. proper type and size to fit the child.

Rear-facing for infants, forwardfacing for small children.

Selecting a Child Seat

The child seat should f it the

3. vehicle seating position (or positions) where it will be used.

Before purchasing a conventional child seat, or using a previously purchased one, we recommend that you test the seat in the specific vehicle seating position or positions where the seat will be used.

Driver and Passenger Safety

Installing a Child Seat

2010 TL

After selecting a proper child seat and a good place to install the seat, there are three main steps in installing the seat:

Properly secure the child seat to

1. the vehicle.

secured to the vehicle with the lap part of a lap/shoulder belt or with the LATCH (Lower Anchors and Tethers for CHildren) system. A child whose seat is not properly secured to the vehicle can be endangered in a crash.

Make sure the child seat is firmly

2. secured.

seat, push and pull the seat forward and f rom side-to-side to verify that it is secure.

All child seats must be

After installing a child

A child seat secured with a seat belt should be installed as firmly as possible. However, it does not need to be ‘‘rock solid.’’ Some side-to-side movement can be expected and should not reduce the child seat’s effectiveness.

If the child seat is not secure, try installing it in a different seating position, or use a different style of child seat that can be firmly secured.

Secure the child in the child seat.

Make sure the child is properly strappedinthechildseat according to the child seat maker’s instructions. A child who is not properly secured in a child seat can be seriously injured in a crash.

The f ollowing pages provide guidelines on how to properly install a child seat. A f orward-facing child seat is used in all examples, but the instructions are the same for rearfacing child seats.

Installing a Child Seat

2010 TL

Installing a Child Seat with LATCH

Your vehicle is equipped with LATCH (Lower Anchors and Tethers for CHildren) at the outer rear seats.

The lower anchors are located between the seat-back and seat bottom, and are to be used only with a child seat designed for use with LATCH.

The location of each lower anchor is indicated by a small button above the anchor point.

BUTTON

LOWER ANCHORS

To install a LATCH-compatible child seat:

STRAPS

Outer seating position

Usethepullstraptolowerthe

2. anchor cover on the lower seat

COVERS

cushion that covers the LATCH

Move the seat belt buckle or

anchor holes in the seat.

tongue away from the lower anchors. Make sure there are no objects

3. near the anchors that could prevent a secure connection between the child seat and the anchors.

CONTINUED

Driver and Passenger Safety

Installing a Child Seat

2010 TL

HEAD RESTRAINT

BUTTON

Outer seating position

Push the button located next to

4. 5. each rear head restraint to pivot the head restraint down.

Rigid type Flexible type

Place the child seat on the vehicle seat, then attach the seat to the lower anchors according to the

Other LATCH-compatible seats have a f lexible-type connector as shown above.

child seat maker’s instructions.

Whatever type you have, follow

6. Some LATCH-compatible seats have a rigid-type connector as

the child seat maker’s instructions for adjusting or tightening the fit.

shown above.

Installing a Child Seat

2010 TL

TETHER STRAP HOOK

ANCHOR

Route the tether strap over the

COVER

head restraint, then attach the tether strap hook to the anchor, making sure the strap is not twisted.

Tighten the tether strap as

8. instructed by the child seat maker.

Push and pull the child seat

9. forward and f rom side-to-side to verify that it is secure.

Installing a Child Seat with a Lap/ Shoulder Belt

When not using the LATCH system, all child seats must be secured to the vehicle with the lap part of a lap/ shoulder belt.

In addition, the lap/shoulder belts in all seating positions except the driver’s have a lockable retractor that must be activated to secure a child seat.

With the child seat in the desired

1. seating position, route the belt through the child seat according to the seat maker’s instructions, then insert the latch plate into the buckle and remove any slack from the lap portion of the belt.

CONTINUED

Driver and Passenger Safety

Installing a Child Seat

2010 TL

To activate the lockable retractor,

2. slowly pull the shoulder part of the belt all the way out until it stops, then let the belt feed back into the retractor.

After the belt has retracted, tug on

3. it. If the belt is locked, you will not be able to pull it out. If you can pull thebeltout,itisnotlocked,and you will need to repeat these steps.

After conf irming that the belt is

4. 5. locked, grab the shoulder part of the belt near the buckle, and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.

To remove slack, it may help to putweightonthechildseat,or push on the back of the seat while pulling up on the belt.

Push and pull the child seat forward and f rom side-to-side to verify that it is secure enough to stay upright during normal driving maneuvers. If the child seat is not secure, unlatch the belt, allow it to retract fully, then repeat these steps.

Installing a Child Seat

2010 TL

To deactivate the lockable retractor and remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract.

Installing a Child Seat with a Tether

TETHER ANCHORAGE POINTS

COVERANCHOR

A child seat with a tether can be installed in any seating position in the back seat, using one of the anchorage points shown above.

Since a tether can provide additional security to the lap/shoulder belt installation, we recommend using a tether whenever one is required or available.

Using an Outer Anchor

TETHER STRAP HOOK

ANCHOR

After properly securing the child

COVER

seat with the lap/shoulder belt (see page ), pivot the head restraint down (see page ) and

157

route the tether strap over the head restraint.

CONTINUED

Driver and Passenger Safety

Installing a Child Seat

2010 TL

Lift the anchor cover, then attach

2. the tether strap hook to the anchor, making sure the strap is not twisted.

Tighten the strap according to the

3. seat maker’s instructions.

Using the Center Anchor

TETHER STRAP HOOK

After properly securing the child

1. seat (see page ), adjust the

COVER

ANCHOR

head restraint to its lowest position, then route the tether strap over the head restraint.

Followsteps2and3inthe

2. previous column.

Protecting Larger Children

2010 TL

When a child reaches the recommended weight or height limit for a forward-facing child seat, the child should sit in a back seat on a booster seat and wear the lap/ shoulder belt.

The f ollowing pages give instructions on how to check proper seat belt fit, what kind of booster seat to use if one is needed, and important precautions f or a child who must sit in front.

Allowing a child age 12 or under to sit in front can result in injury or death if the passenger’s front airbag inflates.

If a child must ride in front, move the vehicle seat as far back as possible, use a booster seat if needed, have the child sit up properly and wear the seat belt properly.

Checking Seat Belt Fit

To determine if a lap/shoulder belt properly fits a child, have the child put on the seat belt, then ask yourself:

Does the child sit all the way back

1. against the seat?

Do the child’s knees bend

2. comfortably over the edge of the seat?

CONTINUED

Driver and Passenger Safety

Protecting Larger Children

2010 TL

Does the shoulder belt cross

3. between the child’s neck and arm?

Is the lap part of the belt as low as

4. possible, touching the child’s thighs?

Will the child be able to stay

5. seated like this for the whole trip?

If you answer yes to all these questions, the child is ready to wear the lap/shoulder belt correctly. If you answer no to any question, the child needs to ride on a booster seat. A child who has outgrown a forward-

Using a Booster Seat

facing child seat should ride in a back seat and use a booster seat until the lap/shoulder belt f its them properly without the booster.

Some states, Canadian provinces and territories also require children to use a booster seat until they reach a given age or weight (e.g., 6 years or 60lbs).Besuretocheckcurrent laws in the states, provinces or territories where you intend to drive.

Booster seats can be high-back or low-back. Whichever style you select, make sure the booster seat meets federal safety standards (see page

) and that you follow the booster

seat maker’s instructions.

If a child who uses a booster seat must ride in f ront, move the vehicle seat as far back as possible and be sure the child is wearing the seat belt properly.

Protecting Larger Children

2010 TL

A child may continue using a booster seat until the tops of their ears are even with the top of the vehicle’s or booster’s seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster seat.

When Can a Larger Child Sit in Front

The National Highway Traffic Safety Administration and Transport Canada recommend that all children age 12 and under be properly restrained in the back seat.

If the passenger’s front airbag inflates in a moderate to severe frontal collision, the airbag can cause serious injuries to a child who is unrestrained, improperly restrained, sitting too close to the airbag, or out of position.

A side airbag also poses risks. If any part of a larger child’s body is in the path of a deploying side airbag, the child could receive possibly serious injuries.

Of course, children vary widely. And while age may be one indicator of when a child can safely ride in f ront, there are other important f actors you should consider.

Physical Size

Physically, a child must be large enough for the lap/shoulder belt to properly fit (see pages and ). If the seat belt does not fit properly, with or without the child sitting on a booster seat, the child should not sit in front.

Maturity

To safely ride in front, a child must be able to f ollow the rules, including sitting properly, and wearing the seat belt properly throughout the ride.

16 53

CONTINUED

Driver and Passenger Safety

Protecting Larger Children

2010 TL

If you decide that a child can safely ride up front, be sure to:

Carefully read the owner’s manual, and make sure you understand all seat belt instructions and all safety information.

Move the vehicle seat to the rearmost position.

Have the child sit up straight, back against the seat, and feet on or near the floor.

Check that the child’s seat belt is properly and securely positioned.

Supervise the child. Even mature children sometimes need to be reminded to fasten the seat belts or sit properly.

Additional Safety Precautions

Do not let a child wear a seat belt across the neck.

in serious neck injuries during a crash.

Do not let a child put the shoulder part of a seat belt behind the back or under the arm.

cause very serious injuries during a crash. It also increases the chance that the child will slide under the belt in a crash and be injured.

Two children should never use the same seat belt.

could be very seriously injured in a crash.

This could result

This could

If they do, they

Do not put any accessories on a seat belt.

improve a child’s comfort or reposition the shoulder part of a seat belt can make the belt less effective and increase the chance of serious injury in a crash.

Devices intended to

Carbon Monoxide Hazard

2010 TL

Your vehicle’s exhaust contains carbon monoxide gas. Carbon monoxide should not enter the vehicle in normal driving if you maintain your vehicle properly and follow the information on this page.

Have the exhaust system inspected for leaks whenever:

The vehicle is raised for an oil change.

You notice a change in the sound of the exhaust.

The vehicle was in a collision that may have damaged the underside.

Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you.

Avoid any enclosed areas or activities that expose you to carbon monoxide.

High levels of carbon monoxide can collect rapidly in enclosed areas, such as a garage. Do not run the engine with the garage door closed. Even with the door open, run the engine only long enough to move the vehicle out of the garage.

With the trunk lid open, airflow can pull exhaust gas into your vehicle’s interior and create a hazardous condition. If you must drive with the trunk open, open all the windows, and set the climate control system as shown below.

If you must sit in your parked vehicle with the engine running, even in an unconfined area, adjust the climate control system as f ollows:

Select the fresh air mode.

1. Select the mode.

2. Set the fan speed to high.

3. Set the temperature control to a

4. comfortable setting.

Driver and Passenger Safety

Safety Labels

2010 TL

These labels are in the locations shown. They warn you of potential hazards that could cause serious injury or death. Read these labels carefully.

If a label comes off or becomes hard to read (except for the U.S. dashboard label which may be removed by the owner), contact your dealer for a replacement.

DASHBOARDRADIATOR CAP

U.S. models only

SUN VISOR

2010 TL

U.S. models

Canadian models

Safety Labels

Driver and Passenger Safety

DOORJAMB

U.S. models Canadian models

2010 TL

Instruments and Controls

2010 TL

This section gives information about the controls and displays that contribute to the daily operation of your vehicle. All the essential controls are within easy reach.

...........................Control Locations . 62

............................Instrument Panel . 63

.............................................Gauges . 75

..................................Fuel Gauge . 75

...................Temperature Gauge . 76

Controls Near the Steering

.........................................Wheel . 130

Windshield Wipers and

.....................................Washers . 131

Automatic Lighting Off

...................................Feature . 135

.....................................Fog Lights . 137

...............Hazard Warning Button . 139

...............Rear Window Defogger . 139

.............................Keys and Locks . 141

......................Immobilizer System . 143

..............................Ignition Switch . 145

....................................Door Locks . 146

..........Instrument Panel Indicators . 64

.............Multi-Information Display . 77

.......Turn Signals and Headlights . 133

.........Daytime Running Lights . 136

......Instrument Panel Brightness . 137

......Steering Wheel Adjustments . 140

............Childproof Door Locks . 147

..............................................Trunk . 148

.....................Remote Transmitter . 151

...............................................Seats . 155

...........................................Mirrors . 161

Driving Position Memory

........................................System . 164

................Keyless Access System . 167

..................................Seat Heaters . 196

............................Power Windows . 198

.......................................Moonroof . 202

...............................Parking Brake . 204

.....................Beverage Holders . 206

..................................Glove Box . 208

............................Vanity Mirror . 209

...................................Sun Visor . 209

...........................Center Pocket . 210

....................Sunglasses Holder . 210

..................................Coat Hook . 211

...............................Interior Lights . 211

......Emergency Trunk Opener . 150

......Trunk Pass-through Cover . 160

...........Keyless Access Remote . 173

........Engine Start/Stop Button . 177

.........Interior Convenience Items . 205

........Accessory Power Sockets . 207

.............Console Compartment . 208

Instruments and Controls

Control Locations

2010 TL

INSTRUMENT PANEL INDICATORS GAUGES MULTI-INFORMATION DISPLAY

MIRROR CONTROLS (P. 162)

DRIVING POSITION MEMORY SYSTEM BUTTONS

POWER DOOR LOCK MASTER SWITCH (P. 146)

POWER WINDOW SWITCHES

TRUNK RELEASE BUTTON

FUEL FILL DOOR RELEASE BUTTON

HOOD RELEASE HANDLE (P. 447)

A/T model with navigation system is shown.

(P. 75)

(P. 164)

(P. 198)

(P. 148)

(P. 445)

SEAT HEATER SWITCHES (P. 196)

USB ADAPTER CABLE (P. 254, 263, 340, 350)

(P. 63)

(P. 77)

＊＊: If equipped

HOMELINK BUTTONS (P. 385)

ACCESSORY POWER SOCKET

(P. 207)

MOONROOF SWITCH (P. 202)

HAZARD WARNING BUTTON (P. 139)

AUDIO CLOCK COMPASS (P. 378)

CLIMATE CONTROL SYSTEM (P. 216)

AUTOMATIC TRANSMISSION MANUAL TRANSMISSION

ACCESSORY POWER SOCKET

AUXILIARY INPUT JACK (P. 371)

(P. 225)

(P. 373)

(P. 207)

(P. 468)

(P. 465)

Instrument Panel

2010 TL

(P. 77)

(P. 72)

HIGH BEAM INDICATOR (P. 71)

ELECTRIC POWER STEERING (EPS) INDICATOR

LOW FUEL INDICATOR

SIDE AIRBAG OFF INDICATOR

CRUISE CONTROL INDICATOR

CRUISE MAIN INDICATOR

LOW TIRE PRESSURE/TPMS INDICATOR (P. 69)

CHARGING SYSTEM INDICATOR (P. 65, 559)

LOW OIL PRESSURE INDICATOR (P. 64, 559)

MALFUNCTION INDICATOR LAMP (P. 64, 560)

DOOR/TRUNK OPEN INDICATOR (P. 71)

VEHICLE STABILITY ASSIST (VSA) OFF INDICATOR

SH-AWD INDICATOR

VEHICLE STABILITY ASSIST (VSA) SYSTEM INDICATOR

FOG LIGHT INDICATOR (P. 71)

＊

If equipped:

A/T model is shown.

(P. 68)

＊

(P. 73)

(P. 68)

MULTI-INFORMATION DISPLAYSEAT BELT REMINDER INDICATOR (P. 64)

SYSTEM MESSAGE INDICATOR (P. 72)

SECURITY SYSTEM INDICATOR

ANTI-LOCK BRAKE SYSTEM (ABS) INDICATOR

LIGHTS ON INDICATOR

KEYLESS ACCESS SYSTEM INDICATOR

(P. 71)

SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P. 67)

＊

(P. 74)

The U.S. instrument panel is shown. Differences for the Canadian models are noted in the text.

(P. 66)

(P. 70)

IMMOBILIZER SYSTEM INDICATOR

PARKING BRAKE AND BRAKE SYSTEM INDICATOR

(P. 65)

(P. 65, 561)

(P. 73)

(P. 67)

(P. 72)

Instruments and Controls

Instrument Panel Indicators

2010 TL

The instrument panel has many indicators to give you important information about your vehicle.

Seat Belt Reminder Indicator

This indicator comes on when you turn the ignition switch to the ON

＊

(II) position. It reminds you and your passengers to fasten your seat belts. A beeper also sounds if you have not fastened your seat belt.

You will also see a ‘‘FASTEN SEAT BELT’’ message on the multiinformation display.

If you turn the ignition switch to the

＊

ON (II) position before fastening your seat belt, the beeper sounds and the indicator flashes. If you do notfastenyourseatbeltbeforethe beeper stops, the indicator stops flashing but remains on.

If your f ront passenger does not fasten their seat belt, the indicator comes on about 6 seconds after the ignition switch is turned to the ON

＊

(II) position.

If either of you do not fasten your seat belt while driving, the beeper will sound and the indicator will flash again at regular intervals, and you will see a ‘‘FASTEN SEAT BELT’’ or ‘‘FASTEN PASSENGER SEAT BELT’’ message on the multiinformation display. For more information, see page .

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and .

178

181

Malfunction Indicator Lamp

You will also see a ‘‘CHECK EMISSION SYSTEM’’ message on the multi-information display. For more information, see page .

560

Low Oil Pressure Indicator

The engine can be severely damaged if this indicator f lashes or stays on when the engine is running, and you will see a ‘‘CHECK ENGINE OIL LEVEL’’ message on the multiinformation display. For more information, see page .

559

Instrument Panel Indicators

2010 TL

Charging System Indicator

If this indicator comes on when the engine is running, the battery is not being charged, and you will also see a ‘‘CHECK CHARGING SYSTEM’’ message on the multi-information display. For more information, see page .

595

Immobilizer System Indicator

This indicator comes on briefly when you turn the ignition switch to the

＊

ON (II) position. It will then go off if you have inserted a properly coded ignition key, on models with keyless access system, if an appropriate keyless access remote is used. If it is not a properly coded key or keyless access remote, the indicator will blink, and the engine’s fuel system will be disabled (see page ).

143

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and . 1.

178 181

U.S. Canada

Parking Brake and Brake System Indicator

This indicator has two functions:

Itcomesonwhenyouturnthe ignition switch to the ON (II)

＊

position. It is a reminder to check the parking brake. Driving with the parking brake not fully released can damage the brakes and tires.

If you drive without releasing the parking brake, a beeper will sound, and you will also see a ‘‘RELEASE PARKING BRAKE’’ message on the multi-information display (see page ).

204

CONTINUED

Instruments and Controls

Instrument Panel Indicators

2010 TL

2. : released the parking brake while the engine is running, or if it comes on while driving, it can indicate a problem in the brake system. You will also see a ‘‘LOW BRAKE FLUID’’ or ‘‘CHECK BRAKE SYSTEM’’ message on the multi-information display. For more information, see page .

561

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. It may also come on brief ly when the ignition switch is turned to the START (III) position.

If this indicator comes on at any other time, there is a problem in the ABS. If this happens, take the vehicle to your dealer to have it checked. With this indicator on, your vehicle still has normal braking ability but no anti-lock function. You will also see a ‘‘CHECK ABS SYSTEM’’ message on the multiinformation display. For more information, see page .

Anti-lock Brake System (ABS) Indicator

＊

482

＊If it stays on after you have fully

Models equipped with the keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II), and START Mode is the equivalent of START (III). For more information, see pages and

181

178

Instrument Panel Indicators

2010 TL

Supplemental Restraint System Indicator Side Airbag Off

This indicator comes on briefly when you turn the ignition switch to the

＊

ON (II) position. If it comes on at any other time, it indicates a potential problem with your front airbags. This indicator will also alert you to a potential problem with your side airbags, passenger’s side airbag cutoff system, side curtain airbags, automatic seat belt tensioners, driver’s seat position sensor, or the front passenger’s weight sensors. You will also see a ‘‘CHECK AIRBAG SYSTEM’’ message on the multi-information display. For more information, see page .

U.S. Canada

Indicator

This indicator comes on briefly when you turn the ignition switch to the

＊

ON (II) position. If it comes on at any other time, it indicates that the passenger’s side airbag has automatically shut off. For more information, see page .

You will also see a ‘‘PASSENGER SIDE AIRBAG OFF’’ message on the multi-information display.

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and .

178 181

Instruments and Controls

Instrument Panel Indicators

2010 TL

Vehicle Stability Assist (VSA) System Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II)

＊

position. It may also come on brief ly when the ignition switch is turned to the START (III) position.

This indicator has two functions:

It flashes when VSA is active (see

1. page ).

484

Ifitcomesonandstaysonatany

2. : other time, or it does not come on when you turn the ignition switch

＊

to the ON (II) position, there is a problem with the VSA or Hill Start Assist (on SH-AWD models only) system. You will also see a ‘‘CHECK VSA SYSTEM’’ or ‘‘CHECK HILL START ASSIST SYSTEM’’ message on the multiinformation display. Take your vehicle to a dealer to have it

checked. Without VSA, your vehicle still has normal driving ability, but will not have VSA traction and stability enhancement. For more inf ormation, see page

484

If the VSA indicator illuminates, hill start assist will not be working. Without hill start assist, the vehicle will roll downhill immediately when you release the brakeonanincline.

181

178

VSA Off Indicator

This indicator comes on as a reminder that you have turned off the vehicle stability assist (VSA) system.

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II)

＊

position. It may also come on brief ly when the ignition switch is turned to the START (III) position. For more information, see page .

484

Instrument Panel Indicators

2010 TL

Low Tire Pressure/ TPMS Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II)

＊

position.

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and .

178 181

This indicator has two functions:

If it comes on while driving, it

1. indicates that one or more of your vehicle’s tires are signif icantly low on pressure.

You will also see a ‘‘CHECK TIRE PRESSURE’’ message on the multiinformation display (see page ).

490

Check the tire pressure monitor on the multi-information display and determinethecause(seepage ).

489

If this happens, pull to the side of the road when it is safe, check which tire has lost pressure on the multiinformation display, and determine the cause. If it is because of a flat tire, have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service. For more information, see page .

570

If this indicator begins to flash,

2. there is a problem with the tire pressure monitoring system (TPMS). You will also see a ‘‘CHECK TPMS SYSTEM’’ message on the multi-information display. The indicator continues to flash for a while (approximately 1 minute), then stays on. If this happens, have your dealer check the system as soon as possible. For more inf ormation, see page

488

Instruments and Controls

Instrument Panel Indicators

2010 TL

Turn Signal and Hazard Warning Indicators

The lef t or right turn signal indicator blinks when you signal a lane change or turn. If an indicator does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see pages and ). Replace the bulb as soon as possible, since other drivers cannot see that you are signaling.

When you press the hazard warning button, both turn signal indicators and all turn signals on the outside of the vehicle flash.

524 528

Electric Power Steering (EPS) Indicator

This indicator normally comes on when you turn the ignition switch to the ON (II) position and goes off after the engine starts. If it comes on at any other time, there is a problem in the electric power steering system.

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and .

181178

＊

If this happens, stop the vehicle in a safe place and turn off the engine. Reset the system by restarting the engine. The indicator will stay on, but should go off after driving a short distance. If it does not go off , or comes back on again while driving, take the vehicle to your dealer to have it checked. With the indicator on, the EPS may be turned of f, making the vehicle harder to steer.

If you turn the steering wheel to the full lef t or right position repeatedly while stopping or driving at very low speed, you may feel slightly harder steering in order to prevent damage to the steering box caused by overheating.

You will also see a ‘‘CHECK POWER STEERING SYSTEM’’ message on the multi-information display.

Instrument Panel Indicators

2010 TL

Lights On Indicator Door/Trunk Open

This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the

or position. This indicator will also come on when the light switch is in AUTO and the lights turn on automatically. If you turn the ignition switch to the ACCESSORY

＊

(I) or the LOCK (0) position, without turning off the light switch, this indicator will remain on. Reminder beeps will also sound when you open the driver’s door.

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. VEHICLE OFF (LOCK) Mode is the equivalent of LOCK (0) and ACCESSORY Mode is the equivalent of ACCESSORY (I). For more inf ormation, see pages

and .

178 181

High Beam Indicator

This indicator comes on with the high beam headlights. For more information, see page .

134

This indicator also comes on with reduced brightness when the daytime running lights (DRL) are on (see page ).

136

Fog Light Indicator

This indicator comes on when you turn on the fog lights. For more information, see page .

137

Indicator

This indicator comes on red if any door or the trunk lid is not closed tightly.

You will also see a corresponding indicator(s) on the multi-information display to indicate which door and/ or the trunk is not closed tightly (see

page ).

Instruments and Controls

Instrument Panel Indicators

2010 TL

Cruise Main Indicator

This indicator comes on when you turn on the cruise control system by pressing the CRUISE button on the steering wheel (see page ).

Cruise Control Indicator

This indicator comes on when you set the cruise control. See page

for inf ormation on operating the

382

cruise control.

382

System Message Indicator

This indicator comes on when there is a system message on the multiinformation display. Press the INFO button on the steering wheel (see page ) to see the message (see

page ).

Most of the time, this indicator comes on along with other indicators in the instrument panel such as the seat belt reminder indicator, SRS indicator, VSA system indicator, etc.

Security System Indicator

SECURITY SYSTEM INDICATOR

This indicator comes on when the security system is set. For more information, see page .

376

Instrument Panel Indicators

2010 TL

Low Fuel Indicator Super Handling-All

When the indicator comes on, there are about 2.5 U.S. gal (9.6

)on

SH-AWD models, and 2.8 U.S. gal

)on2WDmodelsoffuel

(10.5 remaining in the tank.

When the needle reaches E, there is a very small amount of fuel in the tank.

Wheel Drive (SH-AWD) Indicator

On SH-AWD models

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II)

＊

position. If this indicator comes on at any other time, there is a problem in the SH-AWD system. You will also see a ‘‘CHECK SH-AWD SYSTEM’’

LOW FUEL INDICATOR

U.S. model is shown.

message on the multi-information display (see page ). Take your

479

vehicle to a dealer to have it checked.

This indicator is in the fuel gauge. It

For more inf ormation, see page . comesonasareminderthatyou must refuel soon. You will also see a ‘‘LOW FUEL’’ message on the multiinformation display.

＊

Models equipped with the keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

178

181

and .

CONTINUED

Instruments and Controls

478

Instrument Panel Indicators

2010 TL

If the indicator blinks while driving, the differential temperature is too high. You will also see an ‘‘SH-AWD DIFF TEMP. HIGH’’ message on the multi-information display (see page

479 189

Pull to the side of the road when it is safe, shift to Park, and let the engine idle until the indicator goes out.

Continuing to drive with the SH-AWD indicator blinking may cause serious damage to the system.

On models with keyless access system

This indicator normally comes on for a few seconds when you select the ON mode with the engine start/stop button (see page ). If it comes on at any other time, it indicates that there is a problem with the system.

Keyless Access System Indicator

If this indicator comes on along with a ‘‘CHECK KEYLESS ACCESS SYSTEM’’ message on the multi-information display, there is a problem with the keyless access system. Have the vehicle checked by your dealer as soon as possible. For more information, see page .

190

If this indicator comes on along

2. with a ‘‘CHECK KEYLESS STARTING SYSTEM’’ message on the multi-information display, there is a problem with the keyless starting system. In this case, your vehicle may not restart. If you can continue to drive safely, take the vehicle to your dealer and have it checked as soon as possible. For more information, see page .This indicator has two functions:

190

TACHOMETER

2010 TL

MULTI-INFORMATION DISPLAY

SPEEDOMETER

Gauges

Fuel Gauge

This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition/power mode.

Instruments and Controls

TEMPERATURE GAUGE

U.S. model with automatic transmission is shown.

FUEL GAUGE

Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damaging the catalytic converter.

Gauges

2010 TL

Temperature Gauge

This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise from the bottom mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull saf ely to the side of the road. Turn to page for instructions and precautions on checking the engine cooling system. If the pointer of the temperature

557

gauge reaches to or above the red mark, you will also see the ‘‘WATER TEMP HOT’’ message on the multiinformation display. This will alert you that the engine should be cooled down.

Multi-Information Display

2010 TL

The multi-information display in the instrument panel displays various information and messages when the ignition switch is in the ON (II)

＊

position. Some of the messages help you operate your vehicle more comfortably. Others help to keep you aware of the periodic maintenance your vehicle needs for continued trouble-free driving.

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and .

178 181

There are three types of messages: normal display messages, engine oil life and maintenance messages, and system messages.

You can select the displayed language and also customize some vehicle control settings to your liking with the multi-information display and the three buttons on the steering wheel (see page ).

Normal Display Messages

Remote transmitter/keyless access remote 1 is used.

Remote transmitter/keyless access remote 2 is used.

When you unlock and open the driver’s door, the display shows ‘‘DRIVER 1’’ or ‘‘DRIVER 2’’ depending on which remote transmitter/keyless access remote

you use, and the driver’s seat and the outside mirrors move to the position stored in that remote transmitter/ keyless access remote (see page

164

On models with keyless access system

The driver’s ID (1 or 2) is displayed when the power mode is set to ON.

CONTINUED

Instruments and Controls

Multi-Information Display

2010 TL

If you do not fasten your seat belt, you will also see a ‘‘FASTEN SEAT BELT’’ message on the multiinformation display when you turn the ignition switch to the ON (II)

＊

position.

These messages go off several seconds after the key is inserted into the ignition switch.

On models with keyless access system

These messages go off after several seconds.

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and .

178 181

SEL/RESET BUTTON

INFO BUTTONS ( / )

A/T model is shown.

With the ignition switch in the ON

▲▼

＊

(II) position, the multi-inf ormation display changes as shown on page

each time you press the INFO

▲▼

( / ) button or the SEL/RESET button.

When you turn the ignition switch to the ON (II) position, your last selection is displayed.

＊

Multi-Information Display

2010 TL

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and .

178 181

In the multi-information display, the system message is also displayed (see page ) and you can

customize your vehicle control settings (see page ).

U.S. model is shown.

UPPER SEGMENT

LOWER SEGMENT

The multi-information display consists of an upper segment and a lower segment.

In the normal display mode, the upper segment displays trip computer inf ormation, such as f uel economy or average speed. The lower segment displays the odometer/trip meter (A/B), outside temperature, and engine oil life and maintenance item code(s).

On models with keyless access system

You will see some keyless access system messages until you select the ON mode by operating the engine start/stop button. These messages canbecustomized(seepage ).

106

CONTINUED

Instruments and Controls

Multi-Information Display

2010 TL

Odometer (See page 81.) Outside Temperature (See page 84.)

U.S. model is shown.

Trip Meter (See page 81.)

Trip Computer (See page 82.)

Keyless Memory Settings (See page 92.)

＊

HFL (See page 86.)

Engine Oil Life (See page 84.)

＊

2 : SH-AWD models only

＊

SH-AWD Torque Distribution Monitor

(See page 85.)

Tire Pressure for each tire (See page 85.)

: Press the INFO button ( / ).

▲▼

: Press the SEL/RESET button.

On models without navigation system only This display will be shown when the

Bluetooth

HandsFreeLink is activated.

Multi-Information Display

2010 TL

Odometer Trip Meter

U.S.

ODOMETER

Canada

The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect,

This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Each trip meter works independently, so you can keep track of two different distances.

U.S. Canada

TRIP METER A

reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

To reset a trip meter, display it, and then press and hold the SEL/RESET button until the number resets to ‘‘0.0.’’

TRIP METER B

When you reset Trip A, average fuel economy A, average vehicle speed A, and elapsed time A are reset at the same time. When you reset Trip B, average fuel economy B, average vehicle speed B, and elapsed time B are reset.

In the customizing mode, you can set Trip A and average fuel economy A to reset at the same time when you refuel your vehicle (see page ).102

CONTINUED

Instruments and Controls

Multi-Information Display

2010 TL

U.S. model is shown.

Go to SH-AWD monitor (if equipped) or tire pressure monitor. See page 80 for how to switch the main menu display.

: Press the INFO button ( / ). : Press the SEL/RESET button.

▲▼

Trip Computer

Along with the trip meter, the trip computer calculates these values:

Average Fuel Economy Average Vehicle Speed Elapsed Time Instant Fuel Economy Range

Multi-Information Display

2010 TL

This shows your vehicle’s average fuel economy in mpg (U.S. models) or liter/100 km (Canadian models) since you last reset Trip A or Trip B.

You can customize the Trip A and AVG. FUEL A reset condition on the multi-information display (see page

102

AVG. SPEED A/B

This shows the average speed you are traveling in miles per hour (mph) forU.S.modelsorkilometersper hour (km/h) for Canadian models.

ELAPSED TIME A/BAVG.FUEL A/B

This shows the time passed traveled since you last reset it. When you turn the ignition switch to the ON (II)

＊

position, ELAPSED TIME A or B is reset.

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. ON Mode is the equivalent of ON (II). For more information, see pages

and .

178

181

INST. MPG (U.S. models)/INST. L/ 100 km (Canadian models)

This shows your instant fuel economy.

RANGE

This shows the estimated distance you can travel on the fuel remaining in the fuel tank. This distance is estimated from the fuel economy you received over the last several miles (U.S.) or kilometers (Canada), so it will vary with changes in speed, traffic, etc.

Instruments and Controls

Multi-Information Display

2010 TL

Outside Temperature Engine Oil Life

The temperature sensor is in the front bumper. The temperature

U.S. CANADA

reading can be affected by heat reflection f rom the road surface,

ENGINE OIL LIFE

engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h). When you start your trip, the sensor is not f ully acclimatized, theref ore it may take several minutes until the proper

OUTSIDE TEMPERATURE

This shows the outside Fahrenheit temperature in U.S. models, and Celsius temperature in Canadian models.

temperature is displayed.

In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.

U.S. model is shown.

This shows the remaining engine oil life. It shows 100% after the engine oil is replaced and the display is reset. The engine oil life is calculated

based on engine operating conditions. You can adjust the outside temperature display (see page ).

101

For more inf ormation, see page .

497

Multi-Information Display

2010 TL

Tire Pressure Monitor SH-AWD Torque Distribution

U.S. Canada

Monitor

SH-AWD models only

Instruments and Controls

You can see the pressure of each tire in this monitor. If one or more tires are low, inflate them to the correct pressure. For more information, see page .

488

U.S. model is shown.

This monitor shows how much

torque is being delivered to each

wheel. For more information, see

page .

478

Multi-Information Display

2010 TL

Bluetooth

U.S. model is shown.

On models without navigation system

You can receive or make phone calls from your cell phone through your vehicle’s (HFL) system without touching your cell phone.

HandsFreeLink

Bluetooth

HandsFreeLink

To use the system, your cell phone and the HFL system must be linked. Not all cell phones are compatible with this system. Refer to page

for instructions on how to link

394

your cell phone to HFL and how to receive or make phone calls, or visit the acura.com/handsfreelink website. In Canada, visit

, or call 1-888-9-ACURA-9.

On models with navigation system

YoucanseeHFLinformationonthe navigation screen (see page ).

www.acura.

408

Multi-Information Display

2010 TL

System Messages

SYSTEM MESSAGE INDICATOR

A/T model is shown.

vehicle, for example the engine oil level is low or a door is not fully closed, the multi-information display will show you the problem. It does this by interrupting the current display with one or more messages.

The system message(s) triggers the appropriate indicator(s) on the instrument panel, including the system message indicator, to come on. The system message indicator does not go off until the problem(s) is corrected.

You will also hear a beep when the system message comes on for the first time.

Most of the messages are displayed for about 5 seconds, and then the normal display returns. If there are several system messages to be shown, the display switches these messages every 5 seconds.

To switch the message(s) before 5 seconds have elapsed, press the INFO( / )buttononthesteering

▲▼

wheel.

Even if you press the INFO ( / )

▲▼

button, some messages stay on or come on again at regular intervals until the problem is corrected.

If the system message indicator remains lit on the instrument panel, you can see the corresponding message(s) again by pressing the INFO ( / ) button repeatedly.

▲▼If there is a problem with your

Here is a list of all messages:

CONTINUED

Instruments and Controls

Multi-Information Display

2010 TL

U.S.

Canada

See page

U.S.

Canada

U.S.

Canada

U.S.

Canada

See page

559

See page

204

See page

560

See page

559

See page

519

See page

482

See page

484

See page

561

See page

485

SH-AWD model only

Multi-Information Display

2010 TL

U.S.

Canada

U.S. model shown

See page

489

See page

490

See page

490

See page

491

See page

491

See page

136

On models without

keyless access

system

Seepage462

On models with

keyless access

system

Seepage464

A/T model

See page

468

See page

Instruments and Controls

See page

479

SH-AWD model only

See page

479

SH-AWD model only

See page

498

See page

499

See page

500

CONTINUED

Multi-Information Display

2010 TL

See page

446

See page

514

Canadian models only

See page

145

On models without keyless access system

On models with keyless access system

See page

190

See page

190

See page

187

See page

188

See page

192

See page

194

See page

193

A/T model only

See page

182

A/T model only

See page

184

A/T model only

See page

185

See page

182

M/T model only

See page

2010 TL

183

Multi-Information Display

See page

Instruments and Controls

182

See page

185

Multi-Information Display

2010 TL

Keyless Memory Settings

You can customize some vehicle control settings. To change the settings, the ignition switch must be

＊

in the ON (II) position, and the vehicle must be stopped with the transmission in Park (automatic) or with the parking brake set (manual).

If you turn the ignition switch to the

＊

ACCESSORY (I) or the LOCK (0) position, move the shift lever out of Park (automatic) or release the parking brake (manual), the display will change to the normal screen.

＊

Models equipped with the

keyless access system have an engine start/stop button instead of an ignition switch. VEHICLE OFF (LOCK) Mode is the equivalent of LOCK (0), ACCESSORY Mode is the equivalent of ACCESSORY (I), and ON Mode is the equivalent of ON (II). For more information, see pages and

181

178

If you try to enter the customizing mode while the vehicle is moving, you will see a ‘‘MUST STOP AND SHIFTTOPARKTOCHANGE SETTINGS’’ (automatic) or ‘‘MUST STOP AND SET PARK BRAKE TO CHANGE SETTINGS’’ (manual) message and you cannot change the settings.

You can customize some vehicle control settings for ‘‘DRIVER 1’’ and ‘‘DRIVER 2’’ separately.

To have the driver’s ID detected, make sure the driver’s door is unlocked with a corresponding remote transmitter/keyless access remote.

Multi-Information Display

2010 TL

On models without keyless access system

If you use the key to unlock the driver’s door, the system cannot recognize either ‘‘DRIVER 1’’ or ‘‘DRIVER 2.’’

Press the SEL/RESET button.

U.S. model is shown.

If you want to change any vehicle control settings, select Keyless Memory Settings by pressing either INFO button ( / ), then

▲▼

press the SEL/RESET button. Select CHG SETTING, then press the SEL/RESET button.

DRIVER’S ID

Instruments and Controls

Refer to the table on the following pages about the settings you want to customize.

CONTINUED

Multi-Information Display

2010 TL

METER SETUP

LANGUAGE SELECTION

(P.99)

ADJUST OUTSIDE TEMP. DISPLAY

TRIP COMPUTER TRIP A INFO RESET

ADJUST ALARM VOLUME

AUTO INTERIOR ILLUMINAT ION

KEYLESS START GUIDANCE SCREENS

POSITION SETUP

MEMORY POSITION LINK

(P.108)

1:2:Default setting

＊

Only on models with keyless access system

＊

Menu ItemGroup Setup PageSetting OptionDescription

Changes the language used in the display.

Changes the outside temperature reading above or below its current reading.

Causes trip meter A and the average f uel economy to reset when you refuel.

Changes the indicator alarm volumes into three levels.

Changes the interior light sensitivity to your liking.

＊

Changes the display of the keyless start guidance screens. Changes the driver’s seat and the outside mirror positions to a stored setting.

＊

ENGLISH

FRENCH SPANISH

5°F 0°F 5°F

−〜± 〜

(U.S.)

3°C 0°C 3°C

−〜± 〜

(Canada) WITH REFUEL

＊

MANUAL ONLY IGN OFF HIGH

＊

MID LOW MAX HIGH MID ON OFF ON

＊

LOW MIN OFF

OFF

100

101

102

104

105

106

109

Multi-Information Display

2010 TL

Group Setup Page

KEYL ESS ACCESS

＊

SETUP (P.111)

DOOR UNLOCK MODE

KEYL ESS ACCESS LIGHT FLASH

Changes which doors unlock when you use the remote or grab the driver’s door handle. Causes some exterior lights to blink when you unlock/lock the doors by grabbing or touching the

Description Setting OptionMenu Item

DRIVER DOOR ALL DOORS

＊

OFF

sensor/pushing the button on the driver’s door

KEYL ESS ACCESS BEEP

handle. Causes the beeper to sound when you unlock/lock the doors by grabbing or touching the sensor/

ON OFF

＊

pushing the button on the driver’s door handle. LIGHTING SETUP (P.116)

1:2:Default setting

＊

Only on models with keyless access system

＊

INTERIOR LIGHT DIMMING TIME HEADLIGHT AUTO OFF TIMER

AUTO LIGHT SENSITIVIT Y

Changes how long (in seconds) the interior lights

stay on after you close the doors.

Changes how long (in seconds) the exterior lights

stay on after you close the driver’s door.

Changes the timing of when the headlights come

on. The headlight switch needs to be in the AUTO

position.

60 sec 30 sec 60 sec 30 sec 15 sec MAX HIGH MID

＊

15 sec

0sec

＊

LOW

＊

MIN

112

113

114

117

118

119

CONTINUED

Instruments and Controls

Multi-Information Display

2010 TL

DOOR/WINDOW SETUP (P.121)

DEFAULT ALL (P.129)

Default setting1:

＊

2:3:Default setting for automatic transmission

＊

Default setting for manual transmission

＊

AUTO DOOR L OCK

AUTO DOOR UNLOCK

KEY AND REMOTE UNLOCK MODE

KEYLESS LOCK ACKNOWLEDGMENT

SECURITY RELOCK TIMER

Changes when the doors automatically lock.

Changes when the doors automatically unlock.

Changes which doors unlock with the remote

transmitter/keyless access remote on the first

push.

The exterior lights flash each time you press the

LOCK or UNLOCK button. A beeper will also

sound when you press the LOCK button twice.

Changes how long it takes (in seconds) for the

doors to relock and the security system to set after

you unlock but do not open the door.

Set/Cancel all the customized settings as default.

SHIFT FR OM P (A/T only) WITH VEHICLE SPEED

＊

OFF SHIFT TO P/DRIVER

＊

DOOR (A/T only) SHIFT TO P/ALL DOORS (A/T only) IGN OFF/DRIVER DOOR IGN OFF/ALL DOORS OFF DRIVER DOOR

＊

ALL DOORS

＊

ON OFF

90 sec 60 sec

＊

30 sec CANCEL SET

PageDescriptionMenu ItemGroup Setup Setting Option

122

123

＊

125

126

127

129

Multi-Information Display

2010 TL

Customize Settings

You can customize some of the vehicle control settings to your preference. Here are the settings you can customize:

METER SETUP POSITION SETUP KEYLESS ACCESS SETUP

＊

LIGHTING SETUP

＊

: Only on models with keyless

access system

When you want to change the vehicle control settings, press the INFO ( / ) button to select CHG

▲▼

SETTING, then press the SEL/ RESET button.

Each time you press the INFO ( /

▼

) button, the screen changes as

▲

shownonthenextpage.Pressthe INFO( / )buttonuntilyousee

▲▼

the setup you want to customize, then press the SEL/RESET button to enter your selection.

If you do not make any changes, select ‘‘EXIT.’’ The display returns to the normal display.DOOR/WINDOW SETUP

If you want the settings as they were when the vehicle left the factory, select DEFAULT ALL, as described on page .

129

CONTINUED

Instruments and Controls

Acura TL 2010 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual