Briefly appear with each engine start. Red and amber indicators are most critical.
Blue and green indicators are used for general information.
If an indicator remains on, there may be a problem; see your dealer.
Charging system
Low brake fluid
Low oil pressure
SRS
(Supplemental Restraint System)
ABS (Anti-lock Brake System)
SH-AWD®*
(Super Handling-All Wheel Drive system)
Malfunction lamp
(check engine light)
®
VSA
(Vehicle Stability Assist)
TPMS (blinks)
(Tire Pressure Monitoring System)
Brake System
*if equipped
O n / O f f I n d i c a t o r sM a l f u n c t i o n I n d i c a t o r s
PASSENGER AIRBAG OFF
(above audio panel)
SIDE AIRBAG OFF
VSA off
CRUISE MAIN on
CRUISE CONROL on
Fog lights on
Immobilizer (flashes): improperly
coded key; use correct key
Headlights on
Turn signals/hazards on
High beams on
C o n d i t i o n I n d i c a t o r s
Action is needed by driver.
Parking brake on:
Release
Seat belt reminder:
Fasten seat belt(s)
A/T temperature:
Pull over and let engine idle
Message indicator:
See MID
Low fuel:
Refill
Low tire pressure (stays on):
Add air
32
M U L T I - I N F O R M A T I O N D I S P L A Y ( M I D )
Consists of several displays that provide you with useful information.
A c c e s s i n g t h e M I DM a i n D i s p l a y s
When you start the engine, the MID
shows the last active lower display
from the previous drive cycle. Press
either Info button (▲/▼) to show
the last active main display.
Main display
Bluetooth
HandsFreeLink
(if paired)
Instant fuel
economy
Range with
remaining fuel
Total travel time
®
Engine coolant
temperature
®
Tire pressure
monitor
SH-AWD torque
distribution monitor
(if equipped)
Average fuel
economy for
trips A and B
Average speed
To toggle between the different
displays, press either Info button
(▲/▼) for the main displays and
press the SEL/RESET button for
the lower displays.
SEL/RESET
button
INFO
buttons
L o w e r D i s p l a y s
Trip B,
Outside Temperature
Trip A,
Outside Temperature
Oil Life,
Outside Temperature
54
T i r e P r e s s u r e M o n i t o r i n g S y s t e m
Alerts you when one or more of your tires has significantly low pressure. Toggle
to the tire pressure monitor display to view pressure readings on the MID.
C u s t o m i z i n g S e t t i n g s U s i n g t h e M I D
Three groups of settings can be programmed using the MID*: Meter Setup,
Lighting Setup, and Door Setup.
H o w i t W o r k s
If the tire pressure drops significantly below recommended levels:
• The low tire pressure indicator comes on.
• A “CHECK TIRE PRESSURE” message appears on the MID, showing
which tire(s) have low pressure.
W h a t t o D o
1. Visually inspect the tires for
damage.
2. Use a tire air pressure gauge
(or check the MID) to check
which tire(s) have low pressure.
P r o g r a m m i n g t h e A u t o D o o r U n l o c k S e t t i n g
Press and hold either Info button
(▲/▼) to enter customization
mode, then press SEL/RESET to
activate the menu.
SEL/RESET
button
1. Select “CHG SETTING.”
2. Select “DOOR SETUP.”
4. Select “ALL DOORS WITH
SHIFT TO P.”
5. Once the setting has been
saved, select “EXIT.”
Info
buttons
3. Inflate the tire(s), if necessary,
to the recommended pressures
listed on the label on the
driver’s doorjamb.
6
3. Select “AUTO DOOR
UNLOCK.”
* See “Customize Settings” in your Owner’s Manual for other programmable settings.
7
K E Y L E S S M E M O R Y S E T T I N G S
When linked, each remote (labeled 1 or 2 on the back) activates its own set of
programmable driving position memory and customized settings (MID).
C u s t o m i z i n g S e t t i n g s
R e m o t e V e r i f i c a t i o n
1. Verify that the remote you are using is linked to the vehicle by pressing
the lock and unlock buttons at the same time. The LED light on the
remote blinks once to indicate that it is linked or twice if it is unlinked.
2. When you use the remote to unlock the vehicle, the ID number on
the back of the remote should match the memory button
illuminated on the driver door panel. Go to step 3.
• If the numbers still do not match after the remotes have been
linked, follow these instructions:
- Press the lock button on your remote, then press the
unlock button.
D r i v i n g P o s i t i o n M e m o r y S y s t e m ( D P M S )
1. Turn the ignition switch to ON (II).
Shift into Park (P).
2. Adjust your preferred seat and
outside mirror settings.
Note: Each group of settings is activated by the corresponding remote
transmitter (1 or 2). When activated, each item begins to adjust when you
open the driver’s door to enter the vehicle.
3. Press the SET button. You will
hear a beep.
4. Press the memory button
corresponding to the remote
(1 or 2) you are using. You will
hear two beeps.
R E V E R S E T I L T D O O R M I R R O R
When you shift into Reverse (R), the passenger’s outside door mirror tilts down slightly
to improve your view as you parallel park. Shifting out of Reverse returns the tilted
mirror to its original position.
- Whichever memory button is illuminated on the driver
door panel should now match the number on the back of
the remote.
3. Once the remotes are linked, you can begin to program your Keyless
Memory Settings.
8
H o w I t W o r k s
• To tilt the passenger’s
door mirror, move the
mirror selector switch to
the right (R) position
when in Reverse.
• To turn the feature off,
move the switch to the
middle position or left (L)
position.
9
9
Loading...
+ 11 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.