Activeforever Babycom Home Doppler Fetal Heartbeat Monitor User Manual
Home Fetal Monitoring Device
Introduction
Nano Medica has developed Babycom , a patented home fetal monitoring
device that enables fast, easy, convenient detection of the fetal heartbeat
and determines the fetal heart rate. Babycom’s proprietary wide beam angle
ensures accurate results simply and safely. Now, in the privacy of your own
home you can monitor your baby's heartbeat with the same state-of-theart devices used by your medical practitioner. Being able to share this
special experience, creates a bond with you and your family, reassures you,
gives you peace of mind, and connects you to your baby's world.
How It Works
Babycom is based on the Doppler shift principle. The tip of the sensitive
transducer contains two piezoelectric crystals. One crystal transmits very
low ultrasonic waves; the other detects these reflected waves. As these
waves reach moving tissue, such as the fetal heart, they bounce back and
their pitch shifts slightly. This change in pitch is the Doppler shift. Babycom’s
wide ultrasonic beam angle and further algorithmic processing convert the
shifted ultrasonic waves into the audible sound of the fetal heartbeat. (Since
the sound waves do not travel through the air easily, a gel is applied
between the transducer and the abdomen to conduct the sound waves.)
About Diagnostic Ultrasound
Ultrasound in pregnancy has been used as a diagnostic tool for more
than 25 years. It has long been considered one of the safest means
available for obtaining information about the unborn baby. Global studies
and tests conducted by manufacturers, government agencies, and
research institutions have not indicated or revealed any adverse side
effects of diagnostic ultrasound.
H
Home Fetal monitoring device
e
c
i
v
e
d
g
n
i
r
o
t
i
n
o
m
l
a
t
e
F
e
m
o
Manufactured by
medica
NANO
Instructions for Use
Before you begin, sit comfortably. (In early pregnancy a full bladder
may improve sound detection. In later pregnancy the best signals
are generally located higher on the abdomen.)
Apply a liberal amount of gel on the transducer
1.
head (1) or on the abdomen. The gel is necessary
for efficient operation. Lack of a signal can be
due to the absence or insufficient amount of gel.
2.
Turn on the side-mounted roller switch (5) and
adjust the volume control to the preferred level.
3.
Place the transducer (1) directly against the
abdomen, just above the symphysis pubis (the
point where the two pelvic bones meet).
4.
Search for fetal heart signals by slowly moving
the handle across the abdomen. Tilt the handle
slightly as you move the transducer (1) across
and down the lower abdomen until fetal heart
tones are heard. Adjust the handle position to
obtain an optimal audio signal.
5.
Once a clear fetal heart signal is established,
Babycom automatically calculates the derived
fetal heart rate (averaged over a 10-beat period)
and displays it on the LCD (3) after approximately
eight seconds (8sec).
Note:
The fetal heart
sounds like the
hoofbeats of a
galloping horse.
(A rushing wind-like
sound is audible from
the placenta.)
The fetal heart rate
usually ranges
between 140 to 160
beats per minute,
approximately twice
the maternal rate.
(The mother’s heart
rate can be checked
by taking the pulse.)
Repeat the
procedure as often
as you like making
sure to add gel as
needed.
The Babycom Unit
Base
3. LCD Display
4. AudioSystem
Babycom comprises two main parts: a handle and
a base, that are connected by a cable
Handle
The handle contains a sensitive transducer (1) together with
sophisticated electronics and the battery compartment (2). With
efficient battery use, the Babycom unit typically allows for a total
of 250 minutes of monitoring time. Battery life varies according
to duration of examinations, volume level, and battery type.
Base
The base comprises an LCD display (3) and an audio system(4).
Accessories
Ultrasound transmission gel (1 tube).
Care
The base and the transducer should be wiped clean, with
soft cloth or disposable wipe. Keep away from water.
Handle
2. Battery compartment
5. Switch Roller
1. Transducer
Important
1.
Discharging the battery will lead to inaccurate or
indeterminate results. If this occurs, replace the battery.
2.
Babycom cannot determine the fetal heart rate if the
signal is of poor quality due to handle position, fetal
position, maternal position, fetal or maternal movement,
lack of gel, noise or interference.
3.
If the fetal heartbeat is audible but cannot be reliably
calculated due to noise or low signal level, repeat step
4 above.
4.
For best results, keep the handle as still as possible
(to maintain a steady state signal).
Babycom should not be used by you in any way for diagnostic
or other medical purposes. Babycom is not intended and should
not be used as a substitute for regular prenatal care by medical
practitioner. Any concerns about your pregnancy should be
adressed to the medical practitioner. In no event shall Nanomedica
Ltd. be liable for any direct, indirect, or consequential damages
or losses resulting from use of Babycom.
Specifications
Oscillator Frequency (MHz) 2.5
US Intensity, max (mW/cm2) 15
FHR Range (bpm) 50-210
Battery voltage 9V
Battery life 250 operation min
Operating temperature 0 to 40 C
Dimentions (mm) 130(W) x 105(D) x 220(H)
Current Consumption 70mA
Warranty
Nano Medica Ltd. warrants defects for a period of one year from
the date of purchase. During the warranty period the product will
be replaced. This warranty does not apply if the product is modified,
tampered with, misused,or subject to abnormal working conditions.
Loading...