Page 1
TCM-6630
36x Zoom H.264 IP D/N Outdoor Speed Dome
Hardware User’s Manual
Ver. 2012/6/25
Page 2
www.acti.com
TCM-6630 Hardware User’s Manual
Table of Contents
0. Precautions 4
1. Introduction 5
Package Contents ........................................................................... 5
Features and Benefits ..................................................................... 6
Safety Instructions .......................................................................... 8
Physical description ........................................................................ 9
2. Installation Procedure 14
Installing Speed Dome Cover ....................................................... 14
1) Remove the Plastic Protection cap ..................................... 14
2) Apply Lubricant to clear cover ............................................ 14
3) Attach clear cover to speed dome ...................................... 15
Connecting cables ......................................................................... 16
Network Connection .................................................................... 18
Mounting Options for Speed Dome ............................................. 19
Wall .............................................................................................. 19
Corner .......................................................................................... 22
Pole .............................................................................................. 24
Ceiling .......................................................................................... 26
3. Appendix 27
OSD Menu Notes (On Screen Display) .......................................... 27
OSD Display Format .................................................................... 27
OSD Setup Menu ......................................................................... 27
Configuration Menu ..................................................................... 30
Default Camera ............................................................................ 30
Backlight ...................................................................................... 30
FOCUS ........................................................................................ 31
2
Page 3
www.acti.com
TCM-6630 Hardware User’s Manual
APERTURE.................................................................................. 31
AE MODE .................................................................................... 32
WBC MODE ................................................................................. 32
ID DISPLAY .................................................................................. 33
SETUP MENU ............................................................................. 34
TITLE DISPLAY ........................................................................... 36
TITLE SETTING ........................................................................... 36
ALARM SETTING ........................................................................ 37
HOME SETTING .......................................................................... 39
SEQENCE ................................................................................... 40
AUTOPAN .................................................................................... 42
CRUISE........................................................................................ 43
IR FUNCTION (Removable IR Cut).............................................. 44
WDR SETTING ............................................................................ 45
PRIVACY ...................................................................................... 46
TIME FUNCTION ......................................................................... 48
EXIT OSD .................................................................................... 48
Product Specification .................................................................... 49
4. Accessing Camera 51
If you have DHCP server / router in your network: ...................... 51
If you do
NOT
have DHCP server / router in your network: ......... 51
3
Page 4
www.acti.com
TCM-6630 Hardware User’s Manual
0. Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to follow
the safety instruction given may directly endanger people, cause damage to the system or to other
equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your local
office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
FCC/CE Regulation
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the users will be required to correct the interference at their own
expense.
4
Page 5
www.acti.com
TCM-6630 Hardware User’s Manual
1. Introduction
Package Contents
TCM-6630 Power Adaptor
Network Cable Power, Audio and Video Cable
Alarm Cable Waterproof Rubber Sleeve & Mounting Kit
Product CD Accessories (Lubricant / Screws)
Warranty Card
5
Page 6
www.acti.com
TCM-6630 Hardware User’s Manual
Features and Benefits
The IP High Speed Dome is designed to deliver superb performance and durability with an
intelligent and stylish housing. It also provides a reliable real time images with outstanding image
quality (D1, 720x480). It can compress and transmit real time images with outstanding image
quality (30 FPS @ D1, 720 x 480 or 720 x 576) through a standard TCP/IP network. This camera is
your best choice to build an intelligent IP surveillance system.
High Speed Pan-Tilt and Zoom
This High Speed Dome is available:
36x MODEL: 36x optical zoom plus 12x digital magnifier/D&N/WDR
Precise and Accurate Tracking
Scheduling function, a special feature, enables users to program a preset point or patrol sequence.
This IP high speed dome provides variable pan/tilt speed ranging from a fast patrol of 400° per
second to a slow ramble of 5° per second with 0.225° pan accuracy for fast and accurate tracking
ability. The 360° endless rotation and -10°~190° tilt travel makes tracking the object passing directly
beneath the dome very easy. Maximum 256 preset points can be programmed for precise location
of target areas, and you may also define 8 patrol sequences, 4 auto-pan sets and 1 cruise rotation
for the camera to operate automatically.
Day/Night Features
Mechanically Removable IR cut filter ensures 24 hours operation.
Low-Light Application
Digital Slow Shutter and Electronic Shutter functions are provided for clear and high quality image.
The minimum illumination is 0.01 Lux.
Perfect Contrast Solution for High Image Quality
Wide Dynamic Range function is an important feature incorporated to fit your needs
Privacy Mask for Privacy Protection
There are up to 24 configurable privacy zones. This is specially designed to avoid any intrusive
monitoring at specific regions.
6
Page 7
www.acti.com
TCM-6630 Hardware User’s Manual
H.264/MPEG-4/MJPEG Triple Codec Dual Streaming
This device supports 3 compression formats, H.264, MPEG-4 and MJPEG. It brings superior image
quality at 30 frames per second up D1 resolution (720 x 480 pixels).
Built-in Hardware Motion Detection
No more external motion sensors are required. You may assign up to 3 video motion detection
areas. By tuning the object size and sensitivity, it will reliably detect objects passing though in view.
Hardware motion detection also offers better sensitivity and faster response time than software
motion detection.
Powerful Bundled Surveillance Software
To extend the capabilities of the IP Camera, a powerful surveillance program is included in the
package for free. Users can easily use an existing PC as a digital video recorder. Scheduled
recording and manual recording keep every important video recorded in the local hard disk.
Reliable and accurate motion detection with instant warning enables immediate response in every
condition. Quick and simple search and playback function lets you easily find the images and video
you want.
Software Development Kit Support
This IP Camera can be integrated or controlled by applications from third party software developers.
Software developers can save considerable efforts by using our Streaming Library or ActiveX
control. Please contact us for details on integration support.
Digital Time Code Embedded
The “Digital Time Code Embedded” function records video time in the video stream. Therefore,
each image frame is marked with its original recording time. It is very useful when users want to
find the video at an exact time or between a certain time intervals.
7
Page 8
www.acti.com
TCM-6630 Hardware User’s Manual
Safety Instructions
Don’t use the power supply with other voltages
This device is likely to be damaged or damage other equipments / personnel, if you use a power
supply with different voltage than the one included with this device. All warranty of this product will
be voided in the situations above.
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may cause
hazards.
Water and Moisture
Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming pool and the like.
Servicing
Do not attempt to service this video product yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to qualified
service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the video product has been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in this
manual. Adjust only those controls that are covered by the instruction manual, as an improper
adjustment of other controls may result in damage, and will often require extensive work by a
qualified technician to restore the video product to its normal operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
8
Page 9
www.acti.com
TCM-6630 Hardware User’s Manual
Physical description
1) Reset Button
Step 1: Switch off IP device by disconnecting the power cable
Step 2: Press and continue to hold the Reset Button (with a sharp tipped object, like a pen.)
Step 3: Reconnect the power cable while continuing to hold the reset button for 20
seconds. By this time the reset to default operation is already completed. You may then
release the reset button. This length of time fluctuates slightly with the environment. The Power
LED light will come back on and stay on after a few more seconds. The unit will start up with
factory default settings automatically.
9
Page 10
www.acti.com
Pin
Definition
Cable
1
AC 24-1/DC(+)
20 AWG
2
ALM NC
3
AC 24-1/DC(-)
20 AWG
4
ALM NO
5
FG
20 AWG
6
ALM COM
TCM-6630 Hardware User’s Manual
2) Dome Control Protocol
To control PTZ action of this Speed Dome, the control protocol of your software must match the
one used by the Speed Dome Camera. The protocol setting is only available on “07 - DSCP
(Dynacolor)” baud rate 9600 by using firmware v4.12.09 or above version.
Please make sure to turn the switch to the proper number (07).
decimal single digit
3) Ethernet Port
The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this IP
device can auto detect the speed of local network segment (10Base-T/100Base-TX Ethernet).
4) 22 pin connector for Power / Audio In / Audio Out / Video Out / DIO
This 50 cm cable consolidates
all these wires to a single
connection.
Power Input / Audio In / Audio Out / Video Out are
pre-connected. For DIO, there is a separate cable that
you may insert into the 22 pin connector. Please
reference the table below for pin definitions
10
Page 11
www.acti.com
7
MIC +
24 AWG
8
SPK +
9
MIC -
10
SPK -
11
ISOG
12
ALM-1
13
ALM-3
14
ALM-2
15
ALM-4
16
ALM-5
17
ALM-6
18
ALM-7
19
ALM-8
20
ALM GND
21
VGND
24 AWG
22
Video
TCM-6630 Hardware User’s Manual
Please see the graph below on how to insert terminals to connector housing.
11
Page 12
www.acti.com
NOTE: If controlling through an ACTi decoder via analog means such as a
keyboard or DVR, no two speed domes should be given the same ID or
communication conflict may occur. When controlled only through Ethernet
and software (without the use of an ACTi hardware decoder), the dome ID
setting may be ignored.
TCM-6630 Hardware User’s Manual
5) Dome ID Setting
Use the switch to change your speed dome ID by turning the arrow to change each digit to the
desired number. For instance, if the Speed dome ID is 123, the ID switch should be set as below:
12
Page 13
www.acti.com
Communication Switch
Pin 1
RS-232 Setting (Reserved)
Pin 2
Pin 3
Termination
Pin 4
Line Lock
Pin 5
System Initialization (for
upgrade)
Pin 6
Reserved
TCM-6630 Hardware User’s Manual
6) Communication Switch Setting
The table below shows the function of each pin within the Communication Switch
RS-232 is reserved for internal use only; The Pin 3 and Pin 4, they are used for termination and
Link Lock adjustment respectively. The Pin 5 is mainly used for return to factory default of camera
setting.
7) Suspension Loop
This metal cable loop is used to suspend Speed dome from mounting accessories during
installation so that it does not fall down by slipping.
13
Page 14
www.acti.com
TCM-6630 Hardware User’s Manual
2. Installation Procedure
Installing Speed Dome Cover
1) Remove the Plastic Protection cap
Remove the plastic protection cap from the speed dome unit.
2) Apply Lubricant to clear cover
Apply lubricant included in package to dome cover rubber sleeve. This helps ease installation
14
Page 15
www.acti.com
TCM-6630 Hardware User’s Manual
3) Attach clear cover to speed dome
There are a few micro-steps involved here.
First you need to find the plastic stud by the side of dome cover. Insert that into one of the slots at
the side of speed dome.
Secondly, there are two metal screws at the sides of the dome cover. Use a flat headed screwdriver
and unscrew them. Unscrewing will extend them outwards, securing the dome cover.
15
Page 16
www.acti.com
TCM-6630 Hardware User’s Manual
Lastly use the small screw included in package to lock the dome cover into position.
Connecting cables
When installing, please note that you should string the cable through the accessories, the rubber
waterproof sleeve, the mount kit and then into the ports. Please see image below for sequence.
16
Page 17
www.acti.com
TCM-6630 Hardware User’s Manual
There are three locking areas on the mount kit. Put it on top of the speed dome, then rotate it into
position.
Once it is rotated into position, you may use the other larger screw to keep it in place.
17
Page 18
www.acti.com
TCM-6630 Hardware User’s Manual
Network Connection
Follow the diagram below to connect the IP high speed dome to the respective devices.
18
Page 19
www.acti.com
TCM-6630 Hardware User’s Manual
Mounting Options for Speed Dome
Wall
Heavy Duty Wall Mount
PMAX-0309
Heavy Duty Wall Mount + Junction Box
PMAX-0309 + PMAX-0700
19
Page 20
www.acti.com
TCM-6630 Hardware User’s Manual
Gooseneck Wall Mount - Raised
PMAX-0307
Gooseneck Wall Mount - Flat
PMAX-0306
20
Page 21
www.acti.com
TCM-6630 Hardware User’s Manual
Gooseneck Wall Mount + Junction Box
PMAX-0306 + PMAX-0700
21
Page 22
www.acti.com
Corner
Heavy Duty Corner Mount
PMAX-0309 + PMAX-0402
TCM-6630 Hardware User’s Manual
Heavy Duty Corner Mount + Junction Box
PMAX-0309 + PMAX-0402 + PMAX-0700
22
Page 23
www.acti.com
Gooseneck Corner Mount
PMAX-0306 + PMAX-0402
TCM-6630 Hardware User’s Manual
Gooseneck Corner Mount + Junction Box
PMAX-0306 + PMAX-0402 + PMAX-0700
23
Page 24
www.acti.com
Pole
Heavy Duty Pole Mount
PMAX-0309 + PMAX-0502
TCM-6630 Hardware User’s Manual
Heavy Duty Pole Mount + Junction Box
PMAX-0309 + PMAX-0700 + PMAX-0502
24
Page 25
www.acti.com
Gooseneck Pole Mount
PMAX-0306 + PMAX-0502
TCM-6630 Hardware User’s Manual
Gooseneck Pole Mount + Junction Box
PMAX-0306 + PMAX-0700 + PMAX-0502
25
Page 26
www.acti.com
Ceiling
Pendant Mount
PMAX-0109
TCM-6630 Hardware User’s Manual
Pendant Mount + Junction Box
PMAX-0108 + PMAX-0700
** If your camera need to be located far below the mounting point, please use PMAX-0104
extension tube.
26
Page 27
www.acti.com
Position
Function
OSD Display
Description
1
Focus Modes
A
Auto Focus Mode
M
Manual Focus Mode
2
Backlight
X
Back Light Compensation OFF
B
Back Light Compensation ON
3
Alarm
ALARM
Alarm Message
4
Zoom Ratio
×1
Present Zoom Ratio
(Optical Zoom(Digital Zoom)
5
Title
Maximum 20 characters for each title.
16 sets of title are available.
6
Camera ID
Show the camera ID
1
2
3
4
5 6
TCM-6630 Hardware User’s Manual
3. Appendix
OSD Menu Notes (On Screen Display)
OSD Display Format
The information shown on the screen are described in terms of OSD display, position and function
description in the table below.
OSD Setup Menu
The OSD setup menu structure is listed separately in the following section. The star symbol
indicates the factory default.
27
Page 28
www.acti.com
TCM-6630:
Item
Layer 1
Layer 2
Layer 3
Default
DEFAULT
CAMERA
<ON>, <OFF>
ON
BACKLIGHT
ON
BLC Level <000> ~ <100>
OFF
☆
FOCUS
AUTO
Focus Length <1cm>, <10cm>,
<30cm> <1m>
10 cm
MANUAL
<01> ~ <08>
APERTURE
AUTO
☆
MANUAL
H APERTURE <00> ~ <31>
V APERTURE <00> ~ <31>
AE MODE
AUTO
IRIS OFFSET <00> ~ <99>
50
SHUTTER
SHUTTER SPEED <1/2> ~ <1/30000>
IRIS
IRIS <00> ~ <09>
AGC
AGC <00> ~ <05>
WBC MODE
AUTO
☆
MANUAL
R Gain <00> ~ <99>
B Gain <00> ~ <99>
ID DISPLAY
<ON>, <OFF>
ON
SETUP MENU
FLIP
<IMAGE>(K model only), <M.E.>,
<OFF>
OFF
ZOOM SPEED
<FAST>, <SLOW>
Slow
SPEED BY ZOOM
<ON>, <OFF>
OFF
AUTO CALI.
<ON>, <OFF>
OFF
DIGITAL ZOOM
<1> ~ <12>, <OFF>
OFF
SLOW SHUTTER
(K model only)
<1/2> ~ <1/60> Sec. (NTSC)
<1/1.5> ~ <1/50> Sec. (PAL)
1/30
ANGLE
ADJUSTER
ADJUST MIN ANGLE
00
ADJUST MAX ANGLE
90
RESET
RESET
YES
EXIT
TITLE
DISPLAY
<ON>, <OFF>
OFF
TITLE
SETTING
<01> ~ <16>
01
ALARM
SETTNG
ALARM PIN
<1> ~ <8>
1
ALARM SWITCH
<ON>, <OFF>
OFF
ALARM TYPE
<N.O.>, <N.C.>
N.C.
ALARM ACTION
PRESET
☆
SEQUENCE
AUTOPAN
CRUISE
PRESET POINT
SEQUENCE LINE
AUTOPAN LINE
CRUISE LINE
<001> ~ <256>
<1> ~ <8>
<1> ~ <4>
<1>
001
DWELL TIME
<001> ~ <127> Sec., ALWAYS
ALWAYS
EXIT
YES
HOME
SETTING
HOME FUNC.
<ON>, <OFF>
OFF
SELECT MODE
PRESET
☆
SEQUENCE
TCM-6630 Hardware User’s Manual
28
Page 29
www.acti.com
Item
Layer 1
Layer 2
Layer 3
Default
AUTOPAN
CRUISE
PRESET POINT
SEQUENCE LINE
AUTOPAN LINE
CRUISE LINE
<001> ~ <256>
<1> ~ <8>
<1> ~ <4>
<1>
001
RETURN TIME
<001> ~ <128> Min.
001
GO
ENTER
EXIT
YES
SEQUENCE
SEQUENCE LINE
<1> ~ <8>
1
SEQUENCE
POINT
<01> ~ <32>
01
PRESET POS.
<001> ~ <255>, <END>
001
SPEED
<01> ~ <15>
01
DWELL TIME
<000> ~ <127> Sec.
000
RUN SEQUNECE
ENTER
EXIT
AUTOPAN
AUTOPAN LINE
<1> ~ <4>
1
START POINT
<TO FIND>, <TO SAVE>
END POINT
<TO FIND>, <TO SAVE>
DIRECTION
<RIGHT>, <LEFT>
Right
SPEED
<01> ~ <04>
01
RUN AUTOPAN
ENTER
EXIT
CRUISE
RECORD START
RECORD END
RUN CRUISE
EXIT
IR FUNCTION
(K model only)
AUTO
THRESHOLD
<LOW>, <MID>, <HI>
LOW
IR COLOR
<B/W>, <COLOR>
B/W
EXIT
ON
WDR
SETTING
(K model only)
WDR SWITCH
<ON>, <OFF>
OFF
WDR FUNCTION
AUTO
☆
MANUA
L
RATIO LEVEL
<000>~<128>
SHUTTER LEVEL
<000>~<128>
IRIS OFFSET
<000>~<128>
EXIT
PRIVACY
(K model only)
PRIVACY SWITCH
<ON>, <OFF>
OFF
SHADE
<BLACK>, <WHITE>, <GRAY>
Gray
SET MASK
<1> ~
<8>
H CENTER <000> ~ <256>
V CENTER <000> ~ <256>
H SIZE <000> ~ <127>
V SIZE <000> ~ <127>
MASK
CLEAR+RESET
<01> ~< 08>
01
MASK DSIPLAY
<FIRST>, <LAST>
First
EXIT
YES
TIME
TIME DISPLAY
<ON>, <OFF>
OFF
SET YEAR
TCM-6630 Hardware User’s Manual
29
Page 30
www.acti.com
Item
Layer 1
Layer 2
Layer 3
Default
SET MONTH
SET DAY
SET HOUR
SET MINUTE
EXIT+SAVE
EXIT OSD
YES
MAIN PAGE 1
DEFAULT CAMERA OFF
BACKLIGHT OFF
FOCUS AUTO
APERTURE AUTO
AE MODE AUTO
WBC MODE AUTO
ID DISPLAY ON
SETUP MENU ENTER
TCM-6630 Hardware User’s Manual
Configuration Menu
The detailed functions and parameter settings of your high speed dome can be set by the OSD (On
Screen Display) menu with a control program. The functions in OSD menu are described in the
following sections.
36x MODEL
Default Camera
The “DEFAULT CAMERA” is used to restore the camera settings (e.g.
Backlight/Focus/AE//WBC/Aperture). Once any one of the items is modified, the setting will
become <OFF> automatically. Select <ON> for this item to recall the mentioned camera
parameters.
Backlight
The Backlight compensation function prevents the center object from being too dark in
surroundings where excessive light is behind the center object.
30
Page 31
www.acti.com
NOTE: If this function is enabled, the WDR function will be
disabled automatically.
FOCUS LENGTH
TURNING VALUE 10CM
EXIT YES
BLC LEVEL
LEVEL 20
EXIT YES
TCM-6630 Hardware User’s Manual
The Backlight Compensation Level ranges from 000 to 100.
FOCUS
Automatically adjusts the focus position to maximize the high frequency content of the picture in a
center measurement area, taking into consideration the high luminance and strong contrast
components. The focus of the dome camera can be operated in two modes: Manual Focus mode
and Auto Focus mode. Different settings for various models are described as follows.
AUTO
The optimum focus is achieved by the internal digital circuit. Users can adjust the minimum
auto focus range for some special conditions; the options are <1cm>, <10cm>, <30cm> and
<1m>.
MANUAL
In this focus mode, users can adjust the lens focus manually.
APERTURE
Sharpness is the subjective evaluation of detail in the picture. With this “APERTURE” function,
users can adjust the enhancement of the edges of objects in the picture. When shooting text, this
function may help by making them sharper and achieve a better image. There are 32 levels of
adjustment, the options are <00> ~ <31>, <00> represents “no enhancement”.
AUTO
The dome camera will assign a proper aperture value automatically for camera to achieve a better
image.
31
Page 32
www.acti.com
APERTURE MENU
H APERTURE 15
V APERTURE 15
TCM-6630 Hardware User’s Manual
MANUAL
Select this item if you want to adjust aperture value manually. Higher value enhances the
incident ray of camera.
AE MODE
The exposure is the amount of light received by the image sensor and is determined by how
wide you open the lens diaphragm (iris adjustment), by how long you keep the sensor exposed
(shutter speed), and other exposure parameters. With this item, users can define how the Auto
Exposure (AE) function works.
AUTO
In this mode, the camera’s Shutter, IRIS and AGC control function work automatically to
compensate the light exposure of image sensor for consistent video output level. IRIS OFF
SET is used to set the level of IRIS variation.
SHUTTER
With this option, the SHUTTER priority is higher than IRIS and AGC; IRIS and AGC circuit will
function automatically in cooperating with SHUTTER to get consistent exposure.
IRIS
With this option, the IRIS priority is higher than SHUTTER and AGC; SHUTTER and AGC
circuit will function automatically in cooperating with IRIS to get consistent exposure. If the IRIS
is modified manually, the action of exposure compensation depends on the AGC circuit.
AGC
With this option, the AGC priority is higher than SHUTTER and IRIS; SHUTTER and IRIS
circuit will function automatically in cooperating with AGC to get consistent exposure. If AGC is
adjusted manually, the exposure compensation depends on the changing of IRIS.
WBC MODE
A digital camera needs to find reference colour temperature, which is a way of measuring the
quality of a light source, for calculating all the other colours. The unit for measuring this ratio is in
32
Page 33
www.acti.com
Light Sources
Color Temperature in K
Cloudy Sky
6,000 to 8,000
Noon Sun and Clear Sky
6,500
Household Lighting
2,500 to 3,000
75-watt Bulb
2,820
Candle Flame
1,200 to 1,500
WBC MENU
R GAIN 50
B GAIN 50
TCM-6630 Hardware User’s Manual
degree Kelvin (K). You can select one of the White Balance Control modes according to the
condition. The following table shows the colour temperature of some light sources.
AUTO
In this mode, white balance works within its colour temperature range and calculates the
best-fit white balance.
MANUAL
In this mode, users can change the White Balance value manually; adjustable R gain and B
gain range from 0 to 99.
ID DISPLAY
Users are allowed to choose whether the dome ID will be displayed on monitor to identify the
domes.
ON
Display the ID address of the selected dome on the right bottom of the monitor screen.
OFF
Hide the ID address of the selected dome.
33
Page 34
www.acti.com
NOTE: The Privacy Mask function will be automatically
disabled if the Image Flip function is enabled, and “Masking
will be disabled” will be displayed on the screen.
NOTE: The speed dome will only be able to tilt 90°, or -10° ~
100° with angle adjuster adjustments.
FLIP SETTING
FLIP OFF
EXIT YES
TCM-6630 Hardware User’s Manual
SETUP MENU
Users can adjust camera lens model parameters under SETUP MENUs. Depending on the model
of dome cameras, the SETUP MENUs are different.
FLIP (IMAGE/ME/OFF)
User can track an object continuously when it passes through under dome camera with
setting Flip to IMAGE (digital flip) or M.E. (mechanical flip).
IMAGE
IMAGE represents digital IMAGE FLIP, enables users to keep tracking object seamlessly and
no delay occurs in comparing with mechanical flip.
M.E.
The item is a standard mechanical operation. As the dome tilts 90°, it will pan 180°, then
continuing tilt to keep tracking object.
OFF
Select this item to disable the flip function.
34
Page 35
www.acti.com
NOTE: The difference between optical and digital zoom is that
optical zoom uses the lens within the camera to draw the
image closer via zoom in or out to achieve the desired effect.
Optical zoom remains the same and the full resolution of the
zoomed image quality. On the other hand, Digital zoom takes
a portion of image and expands that image to the full size of
the image; however the image quality will be reduced.
TCM-6630 Hardware User’s Manual
ZOOM SPEED
This item is used to set the zoom speed for operating the dome camera.
For this model, the options are <FAST> and <SLOW> (default).
SPEED BY ZOOM
If the item is set to <ON>, the pan/tilt speed will be adjusted by internal algorithm when
zooming automatically. The larger zoom ratio leads the lower rotation speed.
AUTO CALIBRATION
There are one horizontal and one vertical infrared rays check points in each dome. When the
dome camera position may be moved during installation or maintenance, the relative distance
between the original set point and the check point has been changed. Enable the Auto
Calibration function, the dome will automatically detect that and reset the point baack to the
original position.
DIGITAL ZOOM
With this item, users can enable or disable the 12x Digital Zoom. The Digital Zoom activate
after the full Optical Zoom level is reached.
Digital zoom ration is adjustable from <1> to <12>.
SLOW SHUTTER
The shutter speed determines how long the image sensor is exposed to light. To see clear
image in a dark environment, enable this function and select a slower shutter speed.
The shutter speed is adjustable on TCM-6630. With the slowest shutter speed, users can see
objects in a dark environment under 0.2 lux; or see a smooth video image with a higher
shutter speed. The options are from <1/2> to <1/60>.
35
Page 36
www.acti.com
ANGLE ADJUSTER
ADJUST MIN ANGLE -10 DEG
ADJUST MAX ANGLE 100 DEG
EXIT+SET YES
TCM-6630 Hardware User’s Manual
ANGLE ADJUSTER
The item is for adjusting the camera view angle. The ranges of view angle are changed in
different FLIP mode: the angle ranges from -10° to +100° with ME FLIP and FLIP OFF
modes, and from -10° ~ +190° with IMAGE FLIP mode. With IMAGE FLIP function,
users are able to adjust the view angle from -10° ~ +190° to catch the true horizontal
line.
STABILIZER (36x Model Only)
With the Image Stabilizer Function, the speed Dome Camera can capture images that would
otherwise be blurred due to the vibration. The built-in electronic compensation filters out the
vibrations of up to 80% movement at 10Hz, as caused by wind and other environmental
conditions. Its various detection mode ensures total detection for all types of environment. If
the function is activated, users could select the frequency range of either 10Hz or 5Hz.
RESET
Select this item to reset all the camera parameters of SETUP MENUs to the factory dfault.
EXIT
Exit the SETUP MENU1 and go back to MAN MENU.
TITLE DISPLAY
Users are allowed to name a certain view area and display its title for easy recognition. At this item,
users can choose to display or not to display the titles set in advance.
ON
A title set for certain view will be displayed when the dome back to the view area.
OFF
When the TITLE DISPLAY is set <OFF>, no title will be displayed on the screen even titles are
set in advance.
TITLE SETTING
Up to 16 zone titles can be set with maximum 20 characters for each title; two mask zones are
allowed to set in a view area. Users can name the zone titles with privacy mask ID numbers for
future recognition.
36
Page 37
www.acti.com
TITLE SETTING: 01
0 1 2 3 4 5 6 7 8 9
EXIT
A B C D E F G H I J
SAVE
K L M N O P Q R S T
LEFT
U V W X Y Z : / . ,
RIGHT
[ ] + ? -
DELETE
TITLE:
ABC
NOTE: For TCM-6630, the available area for setting privacy
mask is restricted within tilt angle 45°.
ALARM SETTING
ALARM PIN 1
ALARM SWITCH OFF
ALARM TYPE N.C.
ALARM ACTION
PRESET
PRESET POINT 001
DWELL TIME ALWAY
TCM-6630 Hardware User’s Manual
Follow the steps to set a camera title.
(1) Operate speed dome to certain view area where you want to set a title for it.
(2) Turn on OSD and select <TITLE SETTING>.
(3) Select a number to indicate the view area.
(4) Press <ENTER> to go into editing mode.
(5) Choose a character with direction keys and then press <ENTER> to input.
Example: <A> <ENTER>, <B> <ENTER>, <C> <ENTER>
TITLE: ABC
(6) To delete entered characters, move the cursor to <LEFT> or <RIGHT> and press <ENTER> to
select a character in entry field, then move the cursor to <DELETE> and press <ENTER> to
delete the selected character.
(7) When the setting is completed, move the cursor to <SAVE> and press <ENTER> to save.
ALARM SETTING
The integrated high speed dome provides eight alarm inputs and two alarm outputs (N.O. and N.C.)
to connect alarm devices. With this function, dome will cooperates with alarm system to catch the
event images. For wiring, please refer to the installation guide and/or qualified service personnel.
Alarm parameters can be set on this page.
37
Page 38
www.acti.com
TCM-6630 Hardware User’s Manual
ALARM PIN
The dome provides 8 alarm inputs and 2 outputs ( 1 x N.O. and 1 x N.C.). Select an alarm
connector which you want to set its alarm-related parameters with this item, and then set its
alarm-related parameters in Alarm Setting menu.
ALARM SWITCH
The item is used to enable or disable the selected alarm pin function.
ALARM TYPE
There are two kinds of alarm types: Normal Open and Normal Close, which are illustrated as
below. Select an alarm type that corresponds with the alarm application.
ALARM ACTION
Select one of these modes that choose a kind of actions that should be executed when an
alarm is triggered. The alarm actions can be set to execute the preset position, sequence,
auto-pan or cruise function.
PRESET
Select a preset point where the dome should go when an alarm pin is triggered.
SEQUENCE
Select a sequence line that the speed dome camer should execute when alarm pin is triggered.
The Sequence line should be defined prior in SEQENCE setup menu.
AUTOPAN
Select an auto-pan line that the dome camera should execute when alarm pin is triggered. The
Auto-pan line can be defined in setup AUTOPAN menu.
CRUISE
Select a cruise line that the speed dome camera should execute when alarm pin is triggered.
38
Page 39
www.acti.com
NOTE: The DWELL TIME is only accessible when selecting
ALARM ACTION: Preset or Sequence.
HOME SETTING
HOME FUNCTION OFF
SELECT MODE PRESET
PRESET POINT 001
RETURN TIME 001
GO ENTER
EXIT YES
TCM-6630 Hardware User’s Manual
The Cruise line can be defined in CRUISE setup menu.
DWELL TIME
The DWELL TIME is the duration of executing ALARM ACTION: Preset or Sequence. When
alarm takes place, the dome will go to the preset position or execute sequence function and
stay at each sequence point for a period of time (1~127 seconds). If select <Always>, the
dome will go to the preset position and stay there until alarm condition is released or users
rotate the dome.
EXIT
Exit the ALARM SETTING menu.
HOME SETTING
Users are able to set an operation mode to ensure constant monitoring; if the dome idles for a
period of time, the pre-set function will be activated automatically, this is the HOME function. HOME
function allows constant and accurate monitoring, to avoid the speed dome stops or missing
events.
HOME FUNCTION
The item is used to enable or disable the HOME function.
SELECT MODE
Select one of the modes that the dome should execute when HOME function is enabled and
the RETURN TIME is up. The options are <AUTOPAN>, <SEQUENCE>, <CRUISE> and
<PRESET>.
39
Page 40
www.acti.com
SEQUENCE
SEQUENCE LINE 1
SEQUENCE POINT 01
PRESET POSITION 001
SPEED 1
DWELL TIME 001
RUN SEQUENCE ENTER
EXIT YES
TCM-6630 Hardware User’s Manual
PRESET
Select a preset point where the speed dome should go when alarm pin is triggered.
SEQUENCE
Select a sequence line that the speed dome camer should execute when alarm pin is triggered.
The Sequence line should be defined prior in SEQENCE setup menu.
AUTOPAN
Select an auto-pan line that the speed dome camera should execute when alarm pin is
triggered. The Auto-pan line can be defined in setup AUTOPAN setup menu.
CRUISE
Select a cruise line that the speed dome camera should execute when alarm pin is triggered.
The Cruise line can be defined in CRUISE setup menu.
RETURN TIME
The speed dome starts to count down RETURN TIME when the dome idles, and will execute
the SELECT MODE function if the return time is up. The RETURN TIME ranges from 1 to 128
minutes.
GO
If HOME function is enabled, the users are allowed to execute HOME function manually by
selecting this item.
EXIT
Exit the HOME SETTING menu.
SEQENCE
The function executes pre-positioning of the pan, tilt, zoom and focus features in a certain
sequence for a camera. Before set up this function, users must setup at least two preset points.
40
Page 41
www.acti.com
PAN (degree/sec.)
TILT (degree/sec.)
Speed 1
10
8
Speed 2
23
12
Speed 3
35
22
Speed 4
45
30
Speed 5
55
40
Speed 6
65
50
Speed 7
75
58
Speed 8
185
185
Speed 9
205
210
Speed 10
225
240
Speed 11
250
275
Speed 12
280
305
Speed 13
320
335
Speed 14
365
365
Speed 15
400
400
TCM-6630 Hardware User’s Manual
SEQUENCE LINE
There are eight sets of sequence lines built in the speed dome camera. Using LEFT/RIGHT
direction keys to select a line first and then set its sequence points.
SEQUENCE POINT
Up to 32 points can be specified for each sequence line. The sequence points represent the
orders of the preset points that the dome will automatically run, and the bellowing setup items,
PRESET POSITION, SPEED, and DWELL TIME, are related to this item.
PRESET POSITION
Users can assign a specific preset position to the selected sequence point with this item.
SPEED
Users can set the Speed that the dome goes to the next sequence point, and setup speed
range is from 1 ~ 15. Refer to below table for more information.
DWELL TIME
The DWELL TIME is the duration time that the speed dome will stay at the sequence point,
and the range is from <0> to <127> seconds. The speed dome will go to the next sequence
point when the DWELL TIME is up. If the setting is <0>, the speed dome will stay at this
sequence point until users manually move the speed dome.
41
Page 42
www.acti.com
NOTE: The tilt and zoom value of the start point will be
recorded and fixed for the selected auto-pan line.
AUTOPAN
AUTOPAN LINE 1
START POINT TO FIND
END POINT TO FIND
DIRECTION RIGHT
SPEED 1
RUN AUTOPAN ENTER
EXIT YES
TCM-6630 Hardware User’s Manual
RUN SEQUENCE
User can command the speed dome camera to run the selected Sequence line manually.
EXIT
Select the item to exit the SEQUENCE menu.
AUTOPAN
Auto-pan means rotating or scanning side-to-side motion by a speed dome camera to view an area
horizontally. The parameters can be set on this page.
AUTOPAN LINE
There are four sets of auto-pan lines built in speed dome camera. Users are able to command
the speed dome camera to do continuously panning without limit by setting the start point the
same as endpoint.
START POINT
Follow the description to set the start position of the AUTOPAN path.
1. Move the cursor to <START POINT> and press <ENTER> while <TO FIND> item flashes,
the item will turn <TO SAVE> automatically.
2. Move the speed dome to a desired position and press <ENTER> to save the position as
the start point; the cursor will move to <END POINT> automatically. Ensure to set the end
point to complete the auto-pan setting.
END POINT
Users are able to set the end point after the start point is defined. Pan the dome to another
position and press <ENTER> to save the position as the end point.
42
Page 43
www.acti.com
PAN (degree/sec.)
Speed 1
10
Speed 2
23
Speed 3
35
Speed 4
45
CRUISE
RECORD START ENTER
RECORD END ENTER
RUN CRUISE ENTER
EXIT YES
TCM-6630 Hardware User’s Manual
DIRECTION
The item is for setting the AUTOPAN direction of speed dome camera. The speed will start to
pan clockwise from the start point to the end point if your selection is <RIGHT>, and then
return to the start point. The speed dome will start to pan anti-clockwise from the start point to
the end point if your selection is <LEFT>. Refer to below diagram.
SPEED
The item is for defining the speed dome camera rotation speed while running auto-pan. The
speed is adjustable from 1 to 4; refer to the table below for details.
RUN AUTOPAN
After the setting is completed, select this item to manually execute the Auto-pan function.
EXIT
Exit the AUTOPAN setup menu.
CRUISE
A Cruise is a route of manual operations that can be stored and recalled to execute repeatedly. It
can be formed of pan, tilt position.
43
Page 44
www.acti.com
NOTE: Beware of the memory size when building the cruise path.
After the percentage of the buffer becomes 100%, the path will not
be recorded.
IR FUNCTION
THRESHOLD LOW
IR COLOR COLOR
EXIT YES
TCM-6630 Hardware User’s Manual
RECORD START
Follow the description to record the CRUISE path.
1. Rotate the speed dome camera to a desired view area. The percentage of the memory
buffer will be displayed on the screen.
RECORD END
The cursor will be moved RECORD END while building the cruise line; when the setting is
completed, press <ENTER> to save the path.
RUN CRUISE
After the setting is completed, select this item to manually execute the Cruise function.
EXIT
Exit the CRUISE setup menu.
IR FUNCTION (Removable IR Cut)
With the IR cut filter, the speed dome can still catch clear image at night time or very dark light
condition. During day time, the IR cut filter will be on to block the infrared light for clear image;
during night time, the IR cut filter will be removed to catch infrared light to view images in black and
white. Users are able to view color images when the IR function activated.
Refer to the description to operate the removable IR cut filter.
AUTO
The internal circuit will automatically decide the occasion to remove the IR cut filter according
to the value of light condition calculated by the internal light algorithm.
ON
Select the item to remove the IR cut filter.
44
Page 45
www.acti.com
NOTE: The Backlight function will automatically turned off
when the WDR function is enabled, because the WDR
function has better effect than the Backlight compensation.
WDR SETTING
WDR SWITCH OFF
WDR FUNCTION AUTO
EXIT YES
TCM-6630 Hardware User’s Manual
AUTO
The internal circuit will automatically decide the occasion to remove the IR cut filter according
to the image brightness level.
THRESHOLD
The speed dome will remove the filter immediately when the threshold value is reached. The
threshold options are <LOW>, <MID> and <HI>. <LOW> threshold indicates a higher
sensitivity and can improve the reliability of lens.
IR COLOUR
When IR function is enabled, the video output can be programmed as colour or B/W.
ON
Select the item to remove the IR cut filter.
WDR SETTING
The Wide Dynamic Range function is especially effective in solving indoor and outdoor contrast
issues to enhance better image quality and video performance. It enables the speed dome to catch
detailed data from the dark part (Indoor) without any saturation from the bright part (Outdoor). The
parameter of WDR function can be set on this page.
WDR SWITCH
Enable or disable the WDR function with the item.
WDR FUNCTION
The item is used to define the WDR function mode.
45
Page 46
www.acti.com
NOTE: The Image Flip function will be disabled automatically
while the Privacy function is enabled.
PRIVACY
PRIVACY SWITCH ON
SHADE GRAY
SET MASK 01
MASK CLEAR+RESET 01
MASK DISPLAY FIRST
EXIT YES
WDR MODE
RATIO LEVEL 000
SHUTTER SPEED 000
IRIS OFFSET 000
EXIT YES
TCM-6630 Hardware User’s Manual
AUTO
If select <AUTO>, the speed dome camera operates the WDR function automatically.
MANUAL
Users are allowed to adjust WDR function manually by defining the RATIO LEVEL, SHUTTER
SPEED and IRIS OFFSET value.
EXIT
Exit this setup menu.
PRIVACY
The Privacy Mask function aims to avoid any intrusive monitoring. Users can adjust the camera
view position, and adjust the mask size and area. The speed dome camera will memorize the
center of the selected view as an original point, so it will be locked as users enter the Privacy Setup
menu. Refer to the description for setting Privacy masks.
PRIVACY SWITCH
The item is used to enable or disable masking function. Set this item to <ON> before
configuring mask zone.
SHADE
The colour of privacy mask can be selected through this item. The available colours are black,
gray and white.
46
Page 47
www.acti.com
MASK01 MENU
H CENTER 000
V CENTER 000
H SIZE 000
V SIZE 000
TCM-6630 Hardware User’s Manual
SET MASK
After pressing <ENTER> on this item, speed dome will memorize this position as privacy
mask position, up to 8 masks can be set. The model restricts the mask zones to be set too
close with each other.
H CENTER(000 ~ 256)
The original center of mask zone is the center of screen. User can move the center of mask
zone to another position through adjust this value.
V CENTER(000 ~ 256)
The original center of mask zone is the center of screen. User can move the center of mask
zone to another position through adjust this value.
H SIZE(000 ~ 127)
User can adjust the horizontal size of privacy mask through this item. Set the H and V size to
0 can also delete the selected mask.
V SIZE(000 ~ 127)
User can adjust the vertical size of privacy mask through this item. Set the H and V size to 0
can also delete the selected mask.
MASK CLEAR+RESET
The item is used to clear the mask settings of the selected privacy mask. Select a mask and
press <ENTER> to erase its configuration.
MASK DISPLAY
This item is used to set the occasion to display privacy mask.
FIRST
If select this mode, the camera will detect the mask zone of the next preset position and
display the mask in advance, then pan the speed dome to the preset point.
47
Page 48
www.acti.com
NOTE: The available area for setting privacy mask is
restricted within tilt angle 45°, and two mask zones are
allowed to set in a view area.
TIME SETTING
TIME DISPLAY OFF
SET YEAR 05
SET MONTH 10
SET DAY 02
SET HOUR 12
SET MINUTE 12
TCM-6630 Hardware User’s Manual
LAST
If select this mode, the camera will move the speed dome to the preset point, then display the
mask zone.
EXIT
Exit this page.
TIME FUNCTION
The item is used to set the TIME related parameters of the integrated high speed dome.
TIME DISPLAY
Select <ON> to display the Time information on screen, or <NO> not to display.
YEAR / MONTH / DAY
The items are for setting up the system date.
HOUR / MINUTE
This items are for setting up the system time.
EXIT+SAVE
Exit this page.
EXIT OSD
To exit the OSD setup menu, users can select this item.
48
Page 49
www.acti.com
TCM-6630 Hardware User’s Manual
TCM-6630
•Dev ic e
Device Type Speed Dome Camera
Image Sensor Sony EXview HAD Interlaced Scan CCD
Sensor Size 1/4” (3.2 x 2.4 mm)
Horizontal Resolution 650 TVL
Day / Night Yes
Minimum Illumination Color: 0.1 lux; B/W: 0.01 lux
Color to B/W switch DSP based switch, configurable
Mechanical IR Cut Filter Yes
IR Sensitivity Range 700 - 1100 nm
IR LED No
Electronic Shutter 1/1 - 1/10,000 sec (NTSC/PAL)
•Le ns
Focal Length Zoom, f3.4 - 122.4 mm / F1.6 - 4.5
Iris Auto iris
Focus Auto focus
Horizontal Viewing Angle 57.8° - 1.7°
•PT Z
Zoom Ratio 36x optical; 12x digital
Zoom Speed 4 sec (1x to 36x) Manual
Manual Panning Speed 0.5° ~ 90° /s
Manual Tilting Speed 0.5° ~ 90° /s
Preset Panning Speed 5° ~ 400° /s
Preset Tilting Speed 5° ~ 400° /s
Panning Range 0° ~ 360° endless
Tilting Range -10° ~ 190°
Control Remote manual control; 256 preset points; 8 preset tours; auto scan
Preset Panning Accuracy 0.225°
Preset Tilting Accuracy 0.45°
Absolute Positon Yes
Protocol DSCP, Pelco P, Pelco D, AD422, Philips, Kalatel, VCL, JVC, etc.
•Video
Compression H.264, MPEG-4 SP, MJPEG
Maximum Frame Rate vs.
Resolution
30 fps at 720 x 480 (Full D1, NTSC); 25 fps at 720 x 576 (Full D1, PAL)
30 fps at 352 x 240 (CIF, NTSC); 25 fps at 352 x 288 (CIF, PAL)
30 fps at 160 x 112 (QCIF, NTSC); 25 fps at 176 x 144 (QCIF, PAL)
Multi-Streaming Simultaneous dual streams based on two configurations
Bit Rate 28 Kbps - 6 Mbps (per stream)
Bit Rate Mode Constant, Variable
S/N Ratio More than 50 dB
Image Enhancement
Wide dynamic range; Backlight compensation; White balance: automatic,
predefined and manual;
Privacy Mask 16 configurable regions
Text Overlay User defined text on video
Image Orientation Image flip and mirro
Product Specification
49
Page 50
www.acti.com
•Aud io
Compression 8 kHz, Mono, PCM, 16 bit encoding
Audio-In 3.5 mm Phone Jack
Audio-Out 3.5 mm Phone Jack
•Network
Protocol & Service
TCP, UDP, HTTP, HTTPS, DHCP, PPPoE, RTP, RTSP, IPv6, DNS, DDNS,
NTP, ICMP, ARP, IGMP, SMTP, FTP, UPnP
Security
IP address filtering; HTTPS encryption; Password protected user levels; IEEE
•Alarm
Alarm Trigger Video motion detection (3 regions); External device through digital input
Alarm Response
Notify control center; Go to PTZ preset point or preset tour; Change camera
settings; Command other devices; E-mail notification with snapshots;
Upload video, snapshot to FTP server; Activate external device through digital
•Interfac e
Analog Video Output 1, CVBS, 1.0Vp-p with 75 Ω BNC connector
Digital Input 8, terminal block
Digital Output 1, terminal block
•General
Power Source /
Consumption
AC 24V / 65 W (heater on)
Weight
5800 g (12.9 lb)
Dimensions (Ø x H)
172 mm x 302.5 mm (6.7” x 11.9”); 190 mm x 302.5 mm (7.5” x 11.9”) with
Environmental Casing Weatherproof (IP66 rated); Transparent dome cover
Mount Type Pendant, Wall, Corner, Pole
Operating Temperature -45 °C ~ 50 °C (-49 °F ~ 122 °F)
Operating Humidity 10% ~ 85% RH
Approvals Camera: CE, FCC, IP66; Adapter: CE, TUV-GS, UL, RCM, CCC
•Integration
Unified Solution Fully compatible with ACTi software
ISV Integration Software Development Kit (SDK) available
Firmware Access Browser Microsoft Internet Explorer 6.0 or newer
TCM-6630 Hardware User’s Manual
50
Page 51
www.acti.com
TCM-6630 Hardware User’s Manual
4. Accessing Camera
If you have DHCP server / router in your network:
Many network server / routers are able to automatically provide IP addresses through DHCP. If you
are using such a network, just plug in your computer and IP Camera into the network and your IP
device will acquire network address by itself. Find and access the device with our IP Utility program.
You may download it at:
http://www.acti.com/product/detail/Software/ACTi_Utility_Suite
If you do
1. Configure your PC to use the same subnet by changing your PC’s IP address to the
subnet with prefix 192.168.0.XXX. The last number should be anything from 1 to 254
except 100 and other occupied IP addresses. Subnet mask should be 255.555.255.0.
2. The default IP used by this device is 192.168.0.100. Please make sure your PC is
NOT using this address and that no two equipments use the same IP address in the
network.
3. Change your IP address by going to Control Panel ->Manage Network Connections ->
Right click on the connection to change -> Option -> TCP/IP IPv4 Properties.
NOT
have DHCP server / router in your network:
51
Page 52
www.acti.com
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255.0
(NOTE: xxx should be a number
from 1 to 254 except 100, which is
used by the IP device. Please also
make sure that no two equipments
use the same IP address in the
same network..)
TCM-6630 Hardware User’s Manual
4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP:
192.168.0.100
5. When you see the login window, please input default user and password:
Default User: Admin Password: 123456
6. After logging in, you will see the video from camera. To go to the main menu, click
the ”Setup” button on the top left.
52
Page 53
www.acti.com
TCM-6630 Hardware User’s Manual
If you are using a single camera, this is enough to access the device.
If you are using multiple devices, you need to change the current device to another unused
IP address, so that when the next device is connected to the network, no two devices use
the same IP. Please perform the following steps.
7. Go to IP Settings -> Connection Type
8. Change the IP mode to Static.
9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC’s IP address
or 192.168.0.100.). If this is not the first device you add to the network, please also avoid
other devices’ IPs.
53
Page 54
www.acti.com
TCM-6630 Hardware User’s Manual
10. Click “Apply”
11. Please go to System -> Save & Reboot, and click ”Apply”. Internet Explorer will close after a
few seconds. This is normal.
12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example,
192.168.0.101). For the second device or more you add into the network, please type the
correct IP.
13. Adjust the default Video setting by going to Video & Audio -> Video
54
Page 55
www.acti.com
TCM-6630 Hardware User’s Manual
55
Loading...