ACTi SMAX-0005 User Manual
2013/12/06
Bullet with Bundled
Removable Bracket
Mounting on a Corner
using the Accessory Set
Installation Guide
For Models:
D3x / D4x / E3x
E41 / E42 / E43 / E41A / E42A / E43A
www.acti.com
Installation Guide
Table of Contents
Installation Procedures ..................................................... 4
Installation Using the Corner Mount with Bracket and Sealant Tape...... 5
Step 1: Install the Corner Mount ............................................................. 5
Step 2: Install the Bracket ....................................................................... 6
Step 3: Install the Camera....................................................................... 7
Step 4: Connect the Cables .................................................................... 9
Step 5: Access the Camera Live View .................................................... 9
Step 6: Adjust the Viewing Angle and Focus ........................................... 9
Step 7: Attach the Sunshield ................................................................... 9
Installation Using the Corner Mount with Bracket and Flex Conduit .... 10
Step 1: Install the Corner Mount ............................................................ 11
Step 2: Install the Bracket ..................................................................... 12
Step 3: Remove the Pre-installed Network Cable (“Pigtail”).................. 13
Step 4: Prepare the Conduit Gland and Flex Conduit ........................... 14
Step 5: Install the Ethernet Cable ......................................................... 15
Step 6: Connect the Ethernet Cable ..................................................... 16
Step 7: Install the Camera..................................................................... 17
Step 8: Connect the Camera to the Network ......................................... 19
Step 9: Access the Camera Live View .................................................. 19
Step 10: Adjust the Viewing Angle and Focus ....................................... 19
Step 11: Attach the Sunshield ............................................................... 19
Installation Using the Corner Mount with Bracket and Naked Cable .... 20
Step 1: Install the Corner Mount ........................................................... 21
Step 2: Install the Bracket ..................................................................... 22
Step 3: Remove the Pre-installed Network Cable (“Pigtail”).................. 23
Step 4: Install the New Ethernet Cable ................................................. 24
Step 5: Install the Camera..................................................................... 25
Step 6: Connect the Camera to the Network ......................................... 27
Step 7: Access the Camera Live View .................................................. 27
Step 8: Adjust the Viewing Angle and Focus ......................................... 27
Step 9: Attach the Sunshield ................................................................. 27
Appendices ....................................................................... 28
How to Access the Camera Live View ..................................................... 28
How to Adjust Focus ................................................................................. 36
D3x / E3x Series ................................................................................... 36
D4x / E41 / E41A / E42 / E42A / E43 / E43A Series .............................. 38
How to Attach the Sunshield .................................................................... 39
2
www.acti.com
Installation Guide
How to Make an Ethernet Cable ............................................................... 40
Safety Information ............................................................ 41
3
www.acti.com
Installation Guide
Mounting Solution
Required Accessories
Corner Mount with
Mounting Bracket
(SMAX-0005)
PMAX-0402 PMAX-1103
Installation Procedures
The camera can be installed onto a corner using additional mounting accessories. The
accessories can be purchased individually or as an accessory set.
The installation steps vary depending on the preferred waterproof cabling solution. There are 3
ways to do the cabling:
Installation Using the Corner Mount with Bracket and Sealant Tape, see page 5.
Installation Using the Corner Mount with Bracket and Flex Conduit (Not
applicable for D3x Series), see page 10.
Installation Using the Corner Mount with Bracket and Naked Cable (Not
applicable for D3x Series), see page 20.
4
www.acti.com
Installation Guide
Installation Using the Corner Mount with Bracket and
Sealant Tape
Step 1: Install the Corner Mount
1. Align the Corner Mount to the corner wall and mark the location of the eight (8) screw holes.
NOTE:
The illustration above shows only the screw holes on one side of the wall.
Remember to mark the screw holes on the other side of the wall, too.
Due to different corner surfaces and shapes, it is recommended to use the
actual Corner Mount to mark the holes for drilling.
2. Drill the eight (8) screw holes.
3. Attach eight (8) screws (not included in the package) to secure the Corner Mount to the wall.
NOTE: Purchase screws applicable to the wall type you are mounting the Corner Mount to.
5
www.acti.com
Installation Guide
Step 2: Install the Bracket
1. Remove the screw to detach the camera holder from the bracket. Set the holder aside for
later use.
2. Attach the bracket to the corner mount using the three (3) screws supplied in the corner
mount kit.
6
www.acti.com
Installation Guide
Step 3: Install the Camera
1. Align the screw holes of the holder to the bottom screw holes of the camera.
2. Attach the two (2) screws (supplied in the heavy duty bracket package) to secure the camera
to the holder.
3. Align the screw hole of the holder to the heavy duty bracket.
7
www.acti.com
Installation Guide
4. Loosely attach the screw to secure the holder to the bracket.
5. As needed, turn the holder left or right to adjust the camera viewing direction. Then, secure
the screw tightly to fix the position.
6. As needed, loosen the two (2) side screws of the holder and then move the camera up or
down to adjust the camera viewing angle. Then, tighten the two (2) side screws to fix the
position.
8
www.acti.com
Installation Guide
Camera Side
Network Side
Step 4: Connect the Cables
1. Connect the Ethernet cable from the network side to the Ethernet port of the camera to
complete the installation.
NOTES on using Ethernet cables: For outdoor installations, it is recommended to use
exterior-grade Ethernet cables (CAT5/CAT5e/CAT6); ordinary Ethernet cables are only
designed for indoor use and may deteriorate quickly when exposed to outdoor elements.
Exterior-grade Ethernet cables are waterproof and do not require a conduit.
2. If the camera will be installed outdoors, waterproof the cable connection by wrapping it using
a moisture-sealant tape, such as 3M PRODUCTS Core Series 4-1000 (not included in the
package) or equivalent. See example below.
Step 5: Access the Camera Live View
See How to Access the Camera Live View on page 28 for more information.
Step 6: Adjust the Viewing Angle and Focus
Based on the Live View, adjust the viewing angle and focus of the camera. Adjustments vary per
model; for detailed information, please refer to the following sections:
For D3x / E3x camera series, see D3x / E3x Series on page 36.
For D4x / E41 / E41A / E42 / E42A / E43 / E43A series, see D4x / E41 / E41A / E42 /
E42A / E43 / E43A Series on page 38.
Step 7: Attach the Sunshield
See How to Attach the Sunshield on page 39 for more information.
9
www.acti.com
Installation Guide
Installation Using the Corner Mount with Bracket and
Flex Conduit
The D4x, E3x, E41, E41A, E42, E42A, E43, E43A camera series come with a bundled conduit
gland. Use the conduit gland with a 1/2"-size flex conduit (not included in the package) to protect
the Ethernet cable against fierce weather conditions. To use conduit with the camera, the
pre-installed network cable with "pigtail" (female connector) must be replaced with a standard
Ethernet cable.
NOTE: The flex conduit and Ethernet cable are not included in the package and must be sold
separately. When purchasing, make sure the flex conduit size is 1/2" to match the bundled
conduit gland.
To do the waterproof cable installation, also prepare the following tools:
Screwdriver
Pliers
10
www.acti.com
Installation Guide
Step 1: Install the Corner Mount
1. Align the Corner Mount to the corner wall and mark the location of the eight (8) screw holes.
NOTE:
The illustration above shows only the screw holes on one side of the wall.
Remember to mark the screw holes on the other side of the wall, too.
Due to different corner surfaces and shapes, it is recommended to use the
actual Corner Mount to mark the holes for drilling.
2. Drill the eight (8) screw holes.
3. Attach eight (8) screws (not included in the package) to secure the Corner Mount to the wall.
NOTE: Purchase screws applicable to the wall type you are mounting the Corner Mount to.
11
www.acti.com
Installation Guide
Step 2: Install the Bracket
1. Remove the screw to detach the camera holder from the bracket. Set the holder aside for
later use.
2. Attach the bracket to the corner mount using the three (3) screws supplied in the corner
mount kit.
12
www.acti.com
Installation Guide
Step 3: Remove the Pre-installed Network Cable (“Pigtail”)
1. Loosen the three (3) screws to detach the back cover.
NOTE: A cable is connected inside the camera; do not abruptly pull the back cover.
2. Disconnect the network connector.
3. Remove the pre-installed cable gland and network cable using pliers (not included in the
package).
13
Loading...