ACTi ENR-010P User Manual
ENR-010P
ENR-020P
User Manual
2016/05/06
For V4.04.36 Firmware
www.acti.com
ENR-010P/ENR-020P User’s Manual
Legal Notice
Disclaimer
The information contained in this document is intended for general information purposes.
ACTi Corporation shall not be liable for errors contained herein or for incidental or
consequential damages arising from the furnishing, performance, or use of this manual.
The information contained herein is subject to change without notice.
Copyright
Copyright ©2016 ACTi Corporation All Rights Reserved.
Trademarks
ACTi Connecting Vision and its logo are registered trademarks of ACTi
Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
All other product or company names mentioned in this document may be trademarks or
registered trademarks of their respective owners.
2
www.acti.com
ENR-010P/ENR-020P User’s Manual
Regulatory Compliance Information
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to the equipment that are not expressly approved by
the responsible party for compliance could void the user’s authority to operate the equipment.
European Community Compliance Statement
This product has been tested and found to comply with the limits for
Class B Information Technology Equipment according to European
Standard EN 55022 and EN 55024. In a domestic environment, this
product may cause radio interference in which cause the user be
require to take adequate measures.
3
www.acti.com
ENR-010P/ENR-020P User’s Manual
About This Manual
Target Audience
This manual is intended for End Users who execute security tasks such as monitoring
ongoing activities in the building, patrolling secured zones, searching video data and
managing alarms with use of ENR surveillance system. The reader is expected to own not
only the basic operation skills but permissions to access major functionalities defined by the
System Administrator.
You may also visit ACTi Download Center for updates and documents:
http://www.acti.com/downloadcenter
Technical Support
If you have any questions during system installation, please feel free to contact our engineers
via our Customer Help Desk platform http://www.acti.com/CHD.
4
www.acti.com
ENR-010P/ENR-020P User’s Manual
Table of Contents
1 Legal Notice 2
Disclaimer ................................................................................................ 2
Copyright ................................................................................................ 2
Trademarks............................................................................................... 2
Regulatory Compliance Information ...................................................... 3
2 About This Manual 4
Target Audience ....................................................................................... 4
Technical Support .................................................................................... 4
3 Table of Contents 5
4 Introduction 7
Product Overview .................................................................................... 7
ENR Server/Client Architecture .............................................................. 7
At A Glance ............................................................................................... 9
Power Button & Reset Button .............................................................. 10
5 Local Client Operation 13
Log in to & out of ENR .......................................................................... 13
System Overview ................................................................................... 14
Monitoring .............................................................................................. 17
Understand Channel Status ................................................................. 25
Understand Event Notifications ........................................................... 26
Playback……………………………………………………………………….27
5
www.acti.com
ENR-010P/ENR-020P User’s Manual
6 Remote Client Operation 35
Access ENR Server ............................................................................... 35
Monitoring .............................................................................................. 37
Playback……………………………………………………………………….45
6
www.acti.com
ENR-010P/ENR-020P User’s Manual
Introduction
Product Overview
ACTi ENRSeries (hereafter referred to as ENR) is a compact and reliable multi-channel
standalone NVR. It features a stable embedded Linux operating system and capabilities of
supporting mega-pixel resolution H.264 streaming, an HDMI output for local display, PTZ
control, scheduled/event-triggered/event speed-up recording, event management,
synchronized playback, time/event-based playback search and video bookmarks. Its smart
Setup Wizard and intuitive user interface allow the system installer to enjoy effortless
installation experience, while making it easy for new users to get acquainted with the
operation by first-time use. Other than the local client, the remote PC client may access the
ENR system simultaneously, and experience user-friendly web interface customized for
browser-based operations.
ENR Server/Client Architecture
In a video surveillance system architecture, ENR serves as service provider, aimed to run
24/7 non-stop a video management service for clients. An ENR Client makes requests for
monitoring video streams or playing back recordings of ENR.
There are two types of ENR clients: Local Client and Remote Client. A client, connecting
from whether a remote computer or from local, will be offered the same functionalities of
ENR.
Local Client: In the local site, the client user directly operates ENR by connecting an HDMI
monitor and a USB mouse to the physical ENR.
Remote Client: Over the TCP/IP network, the Remote Client communicates with ENR
through HTTP Protocol. This client user will have to use a computer with Internet Explorer
to access the ENR web interface, without the need of installing any client program
beforehand. Logging in to ENR is as simple as visiting a website.
7
www.acti.com
ENR-010P/ENR-020P User’s Manual
8
www.acti.com
ENR-010P/ENR-020P User’s Manual
At A Glance
9
www.acti.com
ENR-010P/ENR-020P User’s Manual
Power Button & Reset Button
You can turn on/off the device with Power Button.
Turn On the Device
Switch the Power Button to “ON”, the Power LED will light up and turn solid red.
Turn Off the Device
As this unit is powered on, the Power LED and System LED are both lit, and the Power
Button is in pressed state. To turn ENR off, please do the following:
1. On Live screen, click Setup Power tab, and click “Shutdown”.
2. The local display screen will turn black, with an information dialogue box showing up.
When the System LED on the front panel is off, you may switch the Power Button to
“OFF” to completely shut down the unit.
10
www.acti.com
ENR-010P/ENR-020P User’s Manual
3 2 1
Reset to Factory Default
By resetting this device, all your system settings and system log will return to factory
default. It is strongly recommended that you back up previous settings with Backup function
and export the system logs before resetting to factory default.
1. To begin, switch the Power Button to “OFF” position to turn off the unit.
2. Press and hold the Reset Button with a pin or clip.
3. Switch the Power Button to “ON” position, make sure the Reset Button remains in
pressed state for a full 5 seconds after the unit is powered on, and then release it. The
unit will enter the resetting process immediately and automatically restart.
11
www.acti.com
ENR-010P/ENR-020P User’s Manual
Item
Indicator Status
Light Color
Description
Power LED
Solid
Red
The device power is on.
LINK(System) LED
Solid
Green
The O/S is running.
LED Indicators
The LED indicators on front panel show the current device status:
12
www.acti.com
ENR-010P/ENR-020P User’s Manual
Local Client Operation
Log in to & out of ENR
To log into ENR system for the first time, you will have to key in the account name and
password in Login window. Please contact your system administrator for account and
password information.
Log In
On Login window, click into the Account and Password fields to enter your account
information.
Log Out
On Live screen, click on the Logout button.
13
www.acti.com
ENR-010P/ENR-020P User’s Manual
CClliicckk ttoo ooppeenn SSeettuupp MMeennuu EEnntteerr PPllaayybbaacckk
System Overview
Main Screen Introduction
ENR local interface is composed of two main screens:
Live screen
After logging in, you will enter Live screen. Live screen is the interface where you see the
live streaming from your cameras and manipulate PTZ functions.
Playback screen
Where you can search the recordings, view the playback, put video bookmarks and export
the video.
14
www.acti.com
ENR-010P/ENR-020P User’s Manual
Input Devices
IN ENR system, a USB mouse is the required input device to do all the operations on user
interface. All the input devices, including USB mouse, USB joystick and USB keyboard are
ready to use when you connect them to ENR via USB 2.0 ports.
The onscreen keyboards allow you to input characters without using a physical one. By
clicking in a character field (e.g. Account or Server name) or number field (e.g. IP address
or Port), the specific onscreen keyboard will be brought up.
Standard Alphabet + Symbol Keyboard
Number + Symbol Keyboard
Symbol Keyboard
15
Loading...