Page 1
Outdoor Mini Dome &
Outdoor Mini Fisheye Dome
Hardware Manual
E924, E925, E926, E927, E928, E929
E924M, E925M, E926M, E927M, E928M, E929M
Ver. 2015/04/17
Page 2
www.acti.com
Hardware Manual
Table of Contents
Precautions 4
Safety Instructions ........................................................................... 6
Introduction 7
List of Models .................................................................................... 7
Package Contents ............................................................................. 9
Physical Description ...................................................................... 10
E924 / E926 / E928 ...................................................................... 10
E925 / E927 / E929 ...................................................................... 10
E924M / E926M / E928M ............................................................. 12
E925M / E927M / E929M ............................................................. 12
Mounting Options ........................................................................... 14
Installation Procedures 15
Step 1: Prepare for Installation ...................................................... 15
Step 2: Open the Dome Cover ....................................................... 16
Step 3: Route the Cables ............................................................... 17
Step 4: Install the Camera .............................................................. 18
Step 5: Waterproof the Cable Connection .................................... 19
M12 Ethernet Cable (for E9xxM models only) .............................. 19
RJ-45 Ethernet Cable (for E9xx models only) .............................. 20
Step 6: Connect to Network ........................................................... 23
Step 7: Access the Camera Live View ........................................... 23
Step 8: Close the Dome Cover ....................................................... 24
Other Adjustments and Accessories 25
How to Install / Remove the Memory Card ................................... 25
How to Insert the Memory Card ................................................... 25
How to Remove the Memory Card ............................................... 25
How to Adjust the Viewing Angle and Orientation ....................... 26
2
Page 3
www.acti.com
Hardware Manual
How to Connect Audio In Device ................................................... 29
How to Replace the Dome Cover ................................................... 30
Accessing the Camera 34
Configure the IP Addresses ........................................................... 34
Using DHCP Server to Assign IP Addresses ................................ 34
Using the Default Camera IP Address .......................................... 36
Access the Camera ......................................................................... 38
3
Page 4
www.acti.com
Hardware Manual
Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to follow
the safety instruction given may directly endanger people, cause damage to the system or to
other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your local
office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
4
Page 5
www.acti.com
Hardware Manual
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to the equipment that are not expressly approved by the
responsible party for compliance could void the user’s authority to operate the equipment.
European Community Compliance Statement
This product has been tested and found to comply with the limits for Class B
Information Technology Equipment according to European Standard EN 55022
and EN 55024. In a domestic environment, this product may cause radio interference in which
cause the user may be required to take adequate measures.
5
Page 6
www.acti.com
Hardware Manual
Safety Instructions
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may cause
hazards.
Water and Moisture
Install other devices (such as PoE injector, alarm, etc.) that will be used with the camera in a dry
place protected from water.
Servicing
Do not attempt to service this video product yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to qualified
service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the video product has been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in this
manual. Adjust only those controls that are covered by the instruction manual, as an improper
adjustment of other controls may result in damage, and will often require extensive work by a
qualified technician to restore the video product to its normal operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
6
Page 7
www.acti.com
Hardware Manual
E924
5MP Outdoor Mini Dome with D/N, Adaptive IR, Basic WDR, Fixed
lens
E924M
5MP Outdoor Mini Dome with D/N, Adaptive IR, Basic WDR,
M12 connector, Fixed lens
E925
5MP Outdoor Mini Fisheye Dome with D/N, Adaptive IR, Basic
WDR, Fixed lens
E925M
5MP Outdoor Mini Fisheye Dome with D/N, Adaptive IR, Basic
WDR, M12 connector, Fixed Lens
E926
10MP Outdoor Mini Dome with D/N, Adaptive IR, Basic WDR, Fixed
lens
E926M
10MP Outdoor Mini Dome with D/N, Adaptive IR, Basic WDR,
M12 connector, Fixed lens
E927
10MP Outdoor Mini Fisheye Dome with D/N, Adaptive IR, Basic
WDR, Fixed lens
E927M
10MP Outdoor Mini Fisheye Dome with D/N, Adaptive IR, Basic
WDR, M12 connector, Fixed lens
Introduction
List of Models
This hardware manual contains the following models:
7
Page 8
www.acti.com
Hardware Manual
E928
3MP Outdoor Mini Dome with D/N, Adaptive IR, Superior WDR,
Fixed lens
E928M
3MP Outdoor Mini Dome with D/N, Adaptive IR, Superior WDR,
M12 connector, Fixed lens
E929
3MP Outdoor Mini Fisheye Dome with D/N, Adaptive IR, Superior
WDR, Fixed lens
E929M
3MP Outdoor Mini Fisheye Dome with D/N, Adaptive IR, Superior
WDR, M12 connector, Fixed lens
From the installation perspective, the above models are very similar; therefore one manual is
used for all of them.
8
Page 9
www.acti.com
Hardware Manual
Camera
(E924, E924M, E926, E926M,
E928, E928M)
Camera
(E925, E925M, E927, E927M,
E929, E929M)
Screw Kit
Drill Template
Hexagon Screwdriver
Extra Desiccant Bag
Cosmetic Cover
(For unused IR LED)
Cable Gland
(Not available in E9xxM models)
Quick Installation Guide
Warranty Card
Drill Template
or
Package Contents
Check if the camera package comes with the following items:
IMPORTANT: When the camera is taken out from the box, the lens cover is covered by a thin film.
DO NOT remove this film. It is used to protect the lens cover from scratches or fingerprint marks
which may happen during installation. Remove this film only after the camera is securely installed
and all connections are complete.
9
Page 10
www.acti.com
Physical Description
4 5 5
E924 / E926 / E928
Hardware Manual
E925 / E927 / E929
10
Page 11
www.acti.com
Hardware Manual
Item
Description
1
Memory Card Slot
Insert a memory card (not included) into the slot for local
recording purposes. See How to Install / Remove the Memory
Card on page 25 for more information.
NOTE: Supports only microSDHC and microSDXC cards.
2
Power LED
Lights up when the camera is powered up and goes off after the
boot up process is complete
3
Reset Button
Restores the factory default settings of the camera. To reset the
camera, while the power is on, press and hold the Reset Button
for at least 5 seconds or until the Power LED lights up.
4
Ethernet Port
(RJ-45)
Connects to a network using an Ethernet cable with RJ-45
connector.
5
Audio Input
Connects to audio input devices, such as a microphone with
built-in amplifier, etc. See How to Connect Audio In Device on
page 29 for more information.
NOTE: The microphone must have a built-in amplifier.
Connecting an ordinary microphone will dwarf sounds and will
result in inaudible recording.
11
Page 12
www.acti.com
E924M / E926M / E928M
4
5
4
Hardware Manual
E925M / E927M / E929M
12
Page 13
www.acti.com
Hardware Manual
Item
Description
1
Memory
Card Slot
Insert a memory card (not included) into the slot for local recording
purposes. See How to Install / Remove the Memory Card on page 25
for more information.
NOTE: Supports only microSDHC and microSDXC cards.
2
Power LED
Lights up when the camera is powered up and goes off after the boot up
process is complete
3
Reset
Button
Restores the factory default settings of the camera. To reset the camera,
while the power is on, press and hold the Reset Button for at least 5
seconds or until the Power LED lights up.
4
Ethernet
Port (M12)
Connects to a network using an Ethernet cable with M12 connector. The
camera uses the female M12 connector with D-coding and PoE type A.
5
Audio Input
Connects to audio input devices, such as a microphone with built-in
amplifier, etc. See How to Connect Audio In Device on page 29 for more
information.
NOTE: The microphone must have a built-in amplifier. Connecting an
ordinary microphone will dwarf sounds and will result in inaudible
recording.
13
Page 14
www.acti.com
Hardware Manual
Mount Types
Accessories
Surface Mount
Suitable when mounting the camera directly on walls or ceilings without
additional mounting accessories. See Installation Procedures on page
15 for more information.
Gangbox
Suitable when mounting the camera on a 4” Round or 4” Octagon
Gangbox. The use of gangbox is lawfully required in some areas in the
United States. A Gangbox Converter (purchased separately) is required
for this type of installation.
Wall Mount
Suitable when mounting the camera on the wall with the camera facing
down as if installed on the ceiling. The Wall Mount (optional mounting
accessory) is required for this type of installation.
Pendant Mount
Suitable when installing the camera on high ceilings where a straight
tube is used to lower the camera. The Pendant Mount with Mount Kit
(optional accessory set) is required for this type of installation.
Mounting Options
Select the most suitable solution for your installation environment. The camera can be mounted
by either of the following methods:
NOTE:
For more information about the mounting solutions and accessories, please check the
Mounting Accessory Selector in our website (http://www.acti.com/mountingselector).
The above mounting accessories are not included in the package. Contact your sales
agents to purchase.
14
Page 15
www.acti.com
Hardware Manual
E9xx Models
E9xxM Models
Exterior-grade Ethernet Cable with
RJ-45 connector (not included; can be
purchased from local stores)
Bundled Cable Gland
Exterior-grade Ethernet Cable with
Waterproof M12 Male Connector,
D-coding and PoE type A (not included;
can be purchased from local stores)
Installation Procedures
This section describes procedures in mounting the camera on a flat surface.
NOTE: The camera images on this documentation are for reference only and may be different
from the actual camera.
Step 1: Prepare for Installation
1. Before installing the camera, prepare the additional accessories required for installation.
2. Depending on the material of the surface where the camera will be installed, it may be
necessary to drill the three (3) screw holes and use the supplied screw tox. In this case,
attach the bundled drill template on the surface and drill the screw holes.
15
Page 16
www.acti.com
Hardware Manual
Step 2: Open the Dome Cover
1. Loosen the three (3) screws using the bundled hex screwdriver.
2. Lift to remove the dome cover.
NOTE:
The dome cover is attached to the camera body by a string, do not abruptly lift the
dome cover!
A desiccant bag is attached underneath the dome cover. DO NOT remove the
desiccant bag to keep the camera interior parts dry. An extra bag is bundled with the
camera that can be used for replacement, as needed, over time.
The photographed model in this section is for demonstration only. The instruction
applies to all models listed in this manual.
16
Page 17
www.acti.com
Hardware Manual
Drill cable hole
within this block.
Step 3: Route the Cables
Determine whether the cable will pass through a hole on the surface or be routed along the
surface:
If the cable will pass through a hole on the surface:
1. Drill the hole for the cable on the surface.
2. Route the cable from the network side through the hole and connect it to the Ethernet port of
the camera.
NOTE: If the camera will be installed outdoors or in places wherein environmental factors
change drastically, make sure to waterproof the cable connection; see Step 5: Waterproof
the Cable Connection on page 19 for instructions.
3. Push the cable through the hole on the surface.
If the cable will be routed along the surface
1. Pull the rubber tab off from the base of the camera.
2. Route the camera cable through this gap.
17
Page 18
www.acti.com
Hardware Manual
Step 4: Install the Camera
1. If necessary, insert a memory card into the memory card slot of the camera. See How to
Insert the Memory Card on page 25 for more information.
2. Install the camera to the surface using the three (3) bundled screws.
NOTE:
Please make sure the screw is flat on the plate.
The photographed model in this section is for demonstration only. The
instruction applies to all models listed in this manual.
18
Page 19
www.acti.com
Hardware Manual
Step 5: Waterproof the Cable Connection
Depending on the camera model, the Ethernet cable or the “pigtail” of the camera may either
have the RJ-45 or M12 connector.
M12 Ethernet Cable (for E9xxM models only)
Typical M12 Ethernet cable has waterproof connection. Simply connect and screw the cable
connectors to make the connection waterproof.
Make sure the connectors are secured tightly.
19
Page 20
www.acti.com
Hardware Manual
Gland Body
Clamping Nut
Sealing Rubber and Claw
RJ-45 Ethernet Cable (for E9xx models only)
When using the RJ-45 Ethernet cable, follow the procedures below to waterproof the cable
connection:
1. Detach the cable gland as shown below.
2. On the network side cable, insert the clamping nut through the Ethernet cable.
3. Insert the sealing rubber and claw through the Ethernet cable.
20
Page 21
www.acti.com
Hardware Manual
4. Make sure the bundled rubber ring is completely aligned on the gap on the gland body.
5. Attach the gland body to the Ethernet port of the camera.
IMPORTANT!
Make sure the rubber ring is completely aligned and flat on the gland body to avoid
possible water leakage.
6. Connect the RJ-45 connector of the network cable to the Ethernet port of the camera.
21
Page 22
www.acti.com
Hardware Manual
7. Insert the sealing rubber and claw into the cable gland body.
8. Attach the clamping nut to the cable gland body. Make sure the clamping nut is tightly
secured and the rubber is squeezed in to avoid water leakage.
DISCLAIMER: ACTi will not be responsible for camera damage caused by water entering the
cable connections.
22
Page 23
www.acti.com
Hardware Manual
Network
AC Power
Source
PoE Injector /
PoE Switch
Power Cable
Ethernet Cable
Ethernet Cable
(Data + Power)
Ethernet Cable
(Data)
Camera
Step 6: Connect to Network
Connect the other end of the network cable to a switch or injector. Then, connect the switch or
injector to a network or PC and a power source. See Power-over-Ethernet (PoE) example
connection diagram below.
Step 7: Access the Camera Live View
See Accessing the Camera on page 34 for more information on how to access the Live View of
the camera.
23
Page 24
www.acti.com
Hardware Manual
Step 8: Close the Dome Cover
1. Align the cable hole side of the dome cover to the direction of the network cable.
2. Tighten the three (3) screws using the supplied hex screwdriver to attach the dome cover.
3. Remove the thin film.
Final installation should look similar to the illustration below.
NOTE: The photographed model in this section is for demonstration only. The instruction
applies to all models listed in this manual.
24
Page 25
www.acti.com
Hardware Manual
Other Adjustments and Accessories
How to Install / Remove the Memory Card
How to Insert the Memory Card
1. Loosen the three (3) screws to remove the dome cover.
2. Insert the memory card into the card slot with the metal contacts facing the bottom side of the
camera.
3. Push the card completely until it clicks into place.
4. Attach the dome cover to the camera and tighten the three (3) screws.
Once inserted, make sure to access the camera Web Configurator and “mount” the card to
prepare the card for local recording. Refer to the camera Firmware User’s Manual for more
information.
How to Remove the Memory Card
In case there is a need to remove the card, make sure to access the camera Web Configurator to
safely “unmount” the card first (see the camera Firmware User’s Manual for more information).
Once unmounted from the firmware, push the card to eject it from the slot.
25
Page 26
www.acti.com
Hardware Manual
How to Adjust the Viewing Angle and Orientation
This section describes the procedures in adjusting the viewing angle and pan direction of the
camera.
Camer Parts Overview
NOTE: Tilt Adjustment Screws are available on Mini Dome cameras only.
1. Open the dome cover.
2. Loosen the three (3) pan adjustment screws.
26
Page 27
www.acti.com
Hardware Manual
3. Move the pan direction.
For mini dome cameras, the arrow indicates the top side orientation.
For mini fisheye dome cameras, the ridge indicates the top side orientation.
4. Once done, tighten the three (3) screws to fix the lens position. For Mini Fisheye dome
cameras, skip to Step 7.
5. For Mini Dome cameras, loosen the two (2) tilt adjustment screws.
27
Page 28
www.acti.com
Hardware Manual
6. Adjust the tilt and tighten back the screws to fix the tilt position.
7. Close the dome cover.
28
Page 29
www.acti.com
Hardware Manual
Audio Input Jack
Audio Device
How to Connect Audio In Device
The camera comes with an audio jack where an audio input device, such as a microphone with a
built-in amplifier, can be connected. The audio-in jack is covered by a rubber protection.
WARNING: Do not remove this rubber protection if the audio-in jack will not be used to avoid
water or dust from entering the jack.
To connect an audio input device, do the following:
1. Pull to remove the rubber protection.
2. Connect the audio input device.
NOTE: The microphone must have a built-in amplifier. Connecting an ordinary microphone
will dwarf sounds and will result in inaudible recording.
3. If the camera is installed outdoors, be sure to wrap the audio connectors with Waterproof
Tape (can be purchased in hardware stores).
DISCLAIMER: ACTi will not be responsible for camera damage due by water leakage
caused by improper waterproofing of cables.
29
Page 30
www.acti.com
Hardware Manual
How to Replace the Dome Cover
For more discrete surveillance needs, the pre-installed dome cover can be replaced with a
smoked, vandal proof dome cover. The smoked dome cover is an optional accessory; contact
your sales agent to purchase.
To replace the dome cover, follow the procedures below:
1. Open the dome cover.
2. Detach the screw securing the cover to the camera module.
3. Remove the four (4) screws securing the dome cover bracket.
4. Remove the bracket and then the transparent dome cover.
30
Page 31
www.acti.com
Hardware Manual
Dome Cover Housing Side
Camera Module Side
Camera logo here
5. Remove the black rubber from the transparent dome cover. Below is an example of the
detached parts.
6. Align and place the rubber on the dome cover housing with the arrow pointing towards the
camera logo. Note that the side of the rubber with 3 lines should face the housing while the
side with 2 lines should face the camera module.
31
Page 32
www.acti.com
Hardware Manual
Camera logo here
Camera logo here
7. Align and place the replacement dome cover with the arrow pointing towards the camera
logo.
8. Align and place the dome cover bracket on the housing with the arrow pointing towards the
camera logo. Tightly attach the four (4) screws to secure the dome cover bracket to the
housing.
9. Attach the screw to secure the dome cover housing to the camera module.
32
Page 33
www.acti.com
10. Close the dome cover.
Hardware Manual
33
Page 34
www.acti.com
Hardware Manual
Accessing the Camera
Configure the IP Addresses
In order to be able to communicate with the camera from your PC, both the camera and the PC
have to be within the same network segment. In most cases, it means that they both should have
very similar IP addresses, where only the last number of the IP address is different from each
other. There are 2 different approaches to IP Address management in Local Area Networks – by
DHCP Server or Manually.
Using DHCP Server to Assign IP Addresses
If you have connected the computer and the camera into the network that has a DHCP server
running, then you do not need to configure the IP addresses at all – both the camera and the PC
would request a unique IP address from DHCP server automatically. In such case, the camera
will immediately be ready for the access from the PC. The user, however, might not know the IP
address of the camera yet. It is necessary to know the IP address of the camera in other to be
able to access it by using a Web browser.
The quickest way to discover the cameras in the network is to use the simplest network
search, built in the Windows system – just by pressing the “Network” icon, all the cameras of the
local area network will be discovered by Windows thanks to the UPnP function support of our
cameras.
In the example below, we successfully found the camera that we had just connected to the
network.
34
Page 35
www.acti.com
Hardware Manual
By double-clicking with the left mouse on the camera model, it is possible to automatically launch
the default browser of the PC with the IP address of the target camera filled in the address bar of
the browser already.
If you work with our cameras regularly, then there is even a better way to discover the
cameras in the network – by using IP Utility. The IP Utility is a light software tool that can not
only discover the cameras, but also list lots of valuable information, such as IP and MAC
addresses, serial numbers, firmware versions, etc, and allows quick configuration of multiple
devices at the same time.
The IP Utility can be downloaded for free from http://www.acti.com/IP_Utility
With just one click, you can launch the IP Utility and there will be an instant report as follows:
You can quickly see the camera model in the list. Click on the IP address to automatically launch
the default browser of the PC with the IP address of the target camera filled in the address bar of
the browser already.
35
Page 36
www.acti.com
Hardware Manual
1 2 3
4
Using the Default Camera IP Address
If there is no DHCP server in the given network, the user may have to assign the IP addresses to
both PC and camera manually to make sure they are in the same network segment.
When the camera is plugged into network and it does not detect any DHCP services, it will
automatically assign itself a default IP:
192.168.0.100
Whereas the default port number would be 80. In order to access that camera, the IP address of
the PC has to be configured to match the network segment of the camera.
Manually adjust the IP address of the PC:
In the following example, based on Windows 7, we will configure the IP address to 192.168.0.99
and set Subnet Mask to 255.255.255.0 by using the steps below:
36
Page 37
www.acti.com
Hardware Manual
Manually adjust the IP addresses of multiple cameras:
If there are more than 1 camera to be used in the same local area network and there is no DHCP
server to assign unique IP addresses to each of them, all of the cameras would then have the
initial IP address of 192.168.0.100, which is not a proper situation for network devices – all the IP
addresses have to be different from each other. The easiest way to assign cameras the IP
addresses is by using IP Utility:
With the procedure shown above, all the cameras will have unique IP addresses, starting from
192.168.0.101. In case there are 20 cameras selected, the last one of the cameras would have
the IP 192.168.0.120.
Later, by pressing the “Refresh” button of the IP Utility, you will be able to see the list of cameras
with their new IP addresses.
Please note that it is also possible to change the IP addresses manually by using the Web
browser. In such case, please plug in only one camera at a time, and change its IP address by
using the Web browser before plugging in the next one. This way, the Web browser will not be
confused about two devices having the same IP address at the same time.
37
Page 38
www.acti.com
Hardware Manual
Functionality
Internet Explorer
Other browsers
Live Video
Yes
Yes*
Live Video Area Resizable
Yes
No
PTZ Control
Yes
Yes
Capture the snapshot
Yes
Yes
Video overlay based configuration (Motion
Detection regions, Privacy Mask regions)
Yes
No
All the other configurations
Yes
Yes
Browser
Required Plug-In
Safari
QuickTime (http://www.apple.com/quicktime/download/)
Other non-Internet Explorer
browsers
Basic VLC Media Player (http://www.videolan.org)
Access the Camera
Now that the camera and the PC are both having their unique IP addresses and are under the
same network segment, it is possible to use the Web browser of the PC to access the camera.
You can use any of the browsers to access the camera, however, the full functionality is
provided only for Microsoft Internet Explorer.
The browser functionality comparison:
* When using non-Internet Explorer browsers, free third-party software plug-ins must be installed
to the PC first to be able to get the live video feed from the camera:
Disclaimer Notice: The camera manufacturer does not guarantee the compatibility of its cameras
with VLC player or QuickTime – since these are third party softwares. The third party has the right
to modify their utility any time which might affect the compatibility. In such cases, please use
Internet Explorer browser instead.
When using Internet Explorer browser, the ActiveX control for video stream management will be
downloaded from the camera directly – the user just has to accept the use of such control when
prompted so. No other third party utilities are required to be installed in such case.
38
Page 39
www.acti.com
Hardware Manual
The following examples in this manual are based on Internet Explorer browser in order to
cover all functions of the camera.
Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web
browser and typing the following address into Web browser’s address bar:
http://192.168.0.100
Upon successful connection to the camera, the user interface called Web Configurator would
appear together with the login page. The HTTP port number was not added behind the IP
address since the default HTTP port of the camera is 80, which can be omitted from the address
for convenience.
Before logging in, you need to know the factory default Account and Password of the camera.
Account: Admin
Password: 123456
39
Page 40
Copyright © 2015, ACTi Corporation All Rights Reserved
7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan 114, R.O.C.
TEL : +886-2-2656-2588 FAX : +886-2-2656-2599
Email: sales@acti.com
Loading...