How it Works
Acson
Loading...
ART 200 AR
Technical Manual
180 pgs14.51 Mb0
user guide manual
6 pgs3.57 Mb0

Acson ART 60 A, ART 55 AR, ART 80 AR, ART 100 AR, ART 100 A Technical Manual

...
Download
Page 1
ART 55 A/AR ART 60 A/AR ART 80 A/AR ART 100 A/AR ART 120 A/AR ART 150 A/AR ART 200 A/AR ART 250 A/AR ART 300 A/AR ART 360 A/AR ART 420 A/AR
A4RT 60 A/AR A4RT 80 A/AR A4RT 100 A/AR A4RT 120 A/AR A4RT 150 A/AR A4RT 200 A/AR A4RT 250 A/AR A4RT 300 A/AR A4RT 360 A/AR
A4RT 420 A/A
R
ART-A_(i)
Rooftop Packaged
Air Conditioners
Page 2
TABLE OF CONTENTS
1. NOMENCLATURE.......................................................................................................... 1
- PRODUCT LINE-UP
2. FEATURES..................................................................................................................... 4
3. APPLICATION INFORMATION........................................................................................ 5
- OPERATING RANGE
- REFRIGERANT CIRCUIT DIAGRAMS
- CONTROLLERS
- PRECAUTION AND INSTALLATION
4. SOUND DATA............................................................................................................... 43
5. SELECTION PROCESS...............................................................................................49
- FAN PERFORMANCE CHART
6. ENGINEERING & PHYSICAL DATA............................................................................63
- GENERAL DATA
- COMPONENTS DATA
- SAFETY DEVICES
7. PERFORMANCE DATA..............................................................................................105
- PERFORMANCE TABLE
8. OUTLINE AND DIMENSION.......................................................................................137
9. ELECTRICAL DATA....................................................................................................143
10. WIRING DIAGRAMS...................................................................................................155
11. SERVICING AND MAINTENANCE.............................................................................170
12. TROUBLESHOOTING................................................................................................173
13. EXPLODED VIEW & PART LIST.............. ..................................................................178
This manual supercedes ART-2009
Page 3
A RT 100 AR - FX AA
Series
A: A series
Model Type
R: Heatpump Blank: Cooling Only
Capacity
100: 100,000 Btu/h
Model Name
RT: Rooftop
Brand
A: Acson
Electrical
F: 380-415V/3Ph/50Hz
Type of ref. connection
X: Not Applicable
Production spec variation
4
Refrigerant
4: R407C Blank: R22
1. NOMENCLATURE
1
Page 4
Product Line-up
FXBA
FXBC
FXBA
FXBC
FXBB
FXBC
FXBA
FXBD
FXBA
FXBD
A(4)RT Cooling Only
Classification
A4RT
ART
Model
Cooling Only
60A FXAB 60A FXAD 80A FXAA XXXXXXXXX 80A FXAC XXXXXXXX 100A FXAA XXXXXXXX 100A FXAC XXXX 120A FXAB XXXXXXXX 120A FXAC XXXXXXXX
150A FXAA X XXXXXXX 150A FXAD X XXXXXXX 200A FXAA X XXXXXXX 200A FXAD X XXXX 250A FXAA XXXX XX 250A FXAC XXXX XX 300A FXAA XXXX XX 300A FXAC XXXX XX 360A FXAC XXX 420A FXAC XXXXX XX 55A FXAI XXXX XX 60A FXAH XXXXXXX 60A FXAI XXXXXXX 80A FXBC X X X X X X 80A FXBH X X X X X X 80A FXBI X X X X X X X X 80A FXBN X X X X X X X 100A FXBC X X X X X X 100A FXBH X X X X X X 100A FXBI X X X X X X X X 100A FXBN X X X X X X X 120A FXBH X X X X X X X X 120A FXBI X X X X X X X X 150A FXBC X X X X X X X 150A FXBH XX X X X X 150A FXBI X X X X X X X X 150A FXBN X X X X X X X 200A FXBC X X X X X X 200A FXBH X X X X X X 200A FXBI X X X X X X X X 200A FXBN 250A FXAA XXXXXXX 250A FXAD XXXXXXX 250A FXAH XXXXX XX 300A FXAA XXXXXXX 300A FXAD XXXXXXX 300A FXAH XXXXX XX 360A FXAA XXXXXXX 360A FXAH XXXXX XX 420A FXAA XXXXXXX 420A FXAH XXXXX XX
Nomenclature
SLM Controller
XXX XXX
X X X
Seq. Controller
Capil lary Tube
Thermal Expansion Valve (TXV)
Normal Fin
Gold (NA549) Fin
X
X
X
X
X
Scroll Compressor
Air Filter
Down Flow
XX XX
XX XXX
XXXX
XX XX
X X X X
Side Flow
XX XX
Convertible
Filter Drier
2
Page 5
A(4)RT Heat Pump
SLM Controller
Seq. Controller
Capillary Tube
Thermal Expansion Valve (TXV)
Normal Fin
Gold (NA549) Fin
Reciprocating Compressor
Scroll Compressor
Air Filter
Down Flow
Side Flow
Convertible
Filter Drier
60AR FXAC XXXXXXX
80AR FXAC XXXXX XXX 100AR FXAC XXXXX XXX 120AR FXAC XXXXX XXX 150AR FXAC XXXXX XXX 200AR FXAC XXXXX XXX 250AR FXAC XXXXXXX 300AR FXAC XXXXXXX 360AR FXAC XXXXXXX 420AR FXAC XXXXXXX
55AR FXAI XXXXXX
60AR FXAH XXXXXXX
60AR FXAI XXXXXXX
80AR FXAC XXXXXX
80AR FXAH XX XX XX
80AR FXAN XXXXXXX 100AR FXAC XXXXXX 100AR FXAH XX XX XX 100AR FXAN XXXXXXX 120AR FXAH XXXXX XXX 120AR FXAI XXXXX XXX 150AR FXAC XX XXXX 150AR FXAH XX XX XX 150AR FXAN XX XXXXX 200AR FXAC XX XXXX 200AR FXAH XX XX XX 200AR FXAN XX XXXXX 250AR FXAA XXXXXXX 250AR FXAD XXXXXX X 250AR FXAH XXXXXXX 300AR FXAA XXXXXXX 300AR FXAD XXXXXX X 300AR FXAH XXXXXXX 360AR FXAH XXXXXXX 420AR FXAH XXXXXXX
ART
Nomenclature
Classification
A4RT
Model
Heat Pump
FXBC
FXBC
FXBC
FXBC
FXBC
FXBH
FXBC
FXBN
FXBC
FXBH
FXBN
FXBH
FXBI
FXBH
FXBC
FXBN
FXBC
FXBH
FXBN
3
Page 6
2. FEATURES
High Efciency
The Acson rooftop unit is supplied with high efciency and reliable scroll compressor (except ART 80/100/150/ 200 AR).
Package Unit
Dubbed the “Plug and Play” equivalent in the air-conditioning industry, the single unit conguration allows hassle
free installation. No additional piping work is required as both the indoor and outdoor sides are pre-connected.
Refrigerant is factory pre-charged to ensure clean and efcient operation.
Flexibility Of Air Supply
Acson rooftop unit uses a belt driven fan such that the air volume and static required can be adjusted according
to the requirement. This exibility allows for wider application.
Flat Top Design
Acson rooftop unit’s at top design allows for maximum utilization of warehouse and container space.
Electrical Control Capability
All series are equipped with our Electronic Remote Controller (SLM and Sequential LCD). The Sequential LCD features 7 days programmable timer, compressor run/error status, cool/heat/fan/dry/auto modes, etc, while the SLM features a 15 hour delay timer, cool/heat/fan/dry/auto modes, etc. Part loading of system capacity is now possible with the use of our Sequential PAC (Package Air-Condition) control for multiple compressor Acson rooftop units (A(4)RT150/200/250/300/360/420 A/AR).
4
Page 7
The use of your air conditioner outside the range of working temperature and humidity can result in serious failure.
Caution :
Ensure the operating temperature is in allowable range.
Cooling (R22)
Cooling Only Unit
Heat pump
Heat Pump Unit Only
Outdoor temp. (°C WB)
Indoor temp. (°C WB)
-9
15 27
18
Outdoor temp. (°C DB)
Indoor temp. (°C WB)
15 24
19
40
50
20 3010 25
30
10
0
52
5
15
20
10
0
-5
20 3010 25
••••••••••
Cooling (R22)
Cooling Mode For Heat Pump Model
Indoor temp. (°C WB)
Outdoor temp. (°C DB)
15 24
46
19
40
50
30
10
0
15 20 3010 25
Cooling (R407C)
Cooling Only Unit & Cooling Mode For Heat Pump Model
Indoor temp. (°C WB)
Outdoor temp. (°C DB)
15 24
46
19
40
50
30
10
0
15 20 3010 25
3. APPLICATION INFORMATION
Operating Range
5
Page 8
A(4)RT55/60A
Refrigerant Circuit Diagrams
6
Page 9
A(4)RT80/100A
7
Page 10
A(4)RT120A
8
Page 11
A(4)RT150/200A
9
Page 12
A(4)RT250/300A
10
Page 13
A(4)RT360/420A
COMP1
11
Page 14
ART55AR
COOLING OPERATION
HEATINGOPERATION
HEAT EXCHANGER
(INDOOR)
4-WAY VALVE
CHECK JOINT
HIGH PRESSURE
SWITCH
DISCHARGE
CHECK JOINT
ACCUMULATOR
COMPRESSOR
CAPILLARYTUBE
BIFLOW FILTER DRIER
TXV
HEAT EXCHANGER
(OUTDOOR)
12
Page 15
A(4)RT60AR
13
Page 16
ART80/100AR
14
Page 17
A4RT80/100AR
15
Page 18
A(4)RT120AR
16
Page 19
ART150/200AR
17
Page 20
A4RT150/200AR
18
Page 21
A(4)RT250/300AR
19
Page 22
A(4)RT360/420AR
COMP1
20
Page 23
SLM Wired Controller (Model: A(4)RT55/60/80/100/120A/AR)
COOL
DRY
HEATMED
HIGH
AUTO
MODE
TEMP
SENSOR
ON/OFF
SLEEP
LOW
TIMER
8
2
5
9
3
6
4
1
FAN
FANON/OFF
TEMP
SLEEP
TIMERMODE
7
1
2
3
4
5
6
10
7
SWING
SWING
FAN
SLM AC-5300(OPTIONAL)
Error Seven Segments
Room Sensor missing/Short
E1 blinking Indoor coil sensor missing/Short E2 blinking Outdoor coil sensor missing/Short E3 blinking Compressor overload E4 blinking
Outdoor abnormal compressor overload trip or gas leak
E5 blinking
Controllers
1. “ON/OFF” Switch
• Press to start the air conditioner unit.
• Press again to stop the unit.
2. Temperature Setting
• Set the desired room temperature.
• Press button to increase or decrease the
set temperature. Setting range are between16ºC to 30ºC (60ºF to 80ºF).
6. “SLEEP” Mode
• Press button to activate the sleep function.
This function can only be activated under “cool” or heating mode operation. When it is activated under ìcoolî mode operation, the set temperature will increase 0.5oC after 30 minutes, 1ºC after 1 hour and 2ºC after 2 hours. If it is activated under “HEAT” mode operation, the set temperature will be decreased 0.5ºC after 30 minutes, 1ºC
3. Operation Modes
after 1 hour and 2ºC after 2 hours.
• Press the “mode” button for select the type
of operating mode.
- Cooling Only : COOL, DRY, FAN
7. Air Swing
• Press button to activate the automatic air
swing function.
- Heat Pump : AUTO, COOL, DRY, HEAT, FAN (AUTO mode is represented by both
COOL and HEAT LED light on)
4. Fan Speed Selection
• Press the button until the desired fan speed
is achieved.
8. Sensor
• Infra red sensor to receive signals from
wireless controller.
9. LED Display
• To display the set temperature (inºC) and
timer delay setting (in hours).
5. Timer
• Press the set button to select the switch
10. Transmission Source
• To transmit signals to the air conditioner.
timer of the air conditioner unit (the setting range is between 1 to 15 hours).
21
Page 24
Sequential Controller (Model: A(4)RT150/200/250/300/360/420A/AR)
E
D
C
B
A
I
H
G
F
Sequential Controller Functions
1) Sequential Controller LCD Display
A : Time display B : Error indication C : Compressor running display (up to 4 compressors) D : Key lock display E : Heater display (up to 2 heaters) F : Energy saving mode display G : Compressor defrost cycle display (up to 4 compressors) H : Operation mode display I : Temperature set display
2) Operating Guide a) ON/OFF Key
Press once to start the air conditioning unit. Press again to stop the unit.
The operation lamp next to the key lights up and goes off respectively when the unit is running or not
running. Caution : In the case when the ON/OFF key is pressed immediately after the operation is stopped, the unit will not restart until 3 minutes later to protect the compressor.
b) Selecting Operation Mode
Press the MODE key to select the type of operating mode. Consecutive press of the key switches the operation over “COOL”, “HEAT”, “AUTO” and “FAN”
c) Save Mode
Press the SAVE key to select the energy saving function. This option is only available for “COOL”, “HEAT” and “AUTO” modes.
d) Auxiliary Electric Heater
If the “HEAT” mode provides insufcient heating to a room even at the highest temperature setting (30ºC), press the HEATER key to activate the auxiliary electric heater. For models with two heaters,
consecutive press of the key allows the selection of one or both heaters active.
e) Temperature Setting
To set the desired room temperature, press or to increase or decrease the set temperature in the range of 16ºC to 30ºC. Press both and simultaneously to toggle between ºC and ºF setting.
f) Time Setting
Real time Clock Press the CLOCK key once to activate set clock mode. Press again to disable set clock mode. Under set clock mode, the time of the present day can be set by pressing the respective MINUTE, HOUR and DAY key.
22
Page 25
7-days timer
Error code
Possible fault
Error
code
Possible fault
E01Require manual reset (possible causes) E02Compressor 1 high temperature (overload) E20 Indoor coil sensor 1 open E03Compressor 2 high temperature(overload) E21 Indoor coil sensor 2 open E06Compressor 1 high pressure trip / contact open E24 Outdoor coil sensor 1 short E07Compressor 2 high pressure trip / contact open E25 Outdoor coil sensor 2 short E10Compressor 1 trip / low R-22 / outdoor abnormal E28 Outdoor coil sensor 1 open E11Compressor 2 trip / low R-22 / outdoor abnormal E29 Outdoor coil sensor 2 open E14Room sensor short E32 Compressor 1 de-ice E15Room sensor open E33 Compressor 2 de-ice E16Indoor coil sensor 1 short E17Indoor coil sensor 2 short
Press the ON TIMER key to activate auto-ON timer mode. Under this mode, press the respective MINUTE, HOUR and DAY key to select the time of the week when the air-conditioning unit is to automatically start running. Press the ON TIMER key again to save the setting.
Press the OFF TIMER key to activate auto-OFF timer mode. Under this mode, press the respective MINUTE, HOUR and D AY key to select the time of the week when the air-conditioning unit is to automatically stop running. Press the ON TIMER key again to save the setting.
Then to activate the 7-days timer, press and hold the TIMER ACTIVE key until the word “TIMER ACTIVE” appears on the LCD screen. Repeat the same step to disable the 7-days timer.
g) Other Function
Key Lock Press the MINUTE key 3 times consecutively and fast to activate the key lock. A “KEY LOCK” symbol will appear on the LCD screen. At this point, only the ON/OFF key is valid. To disable the key lock, again press the MINUTE key 3 times consecutively and fast.
Test run Press the TEST key 2 times consecutively to test run the unit.
3) Error Code
When the system is on and an error occurs, the ON/OFF LED on the LCD panel will blink and an error code is shown. When the system is off and there is a thermistor error, the ON/OFF LED is off but the error code is still displayed. Each error code represents different message as below
4) Installation Of LCD Remote Controller a) Accessories
The following accessories are included. If any part is missing, contact your dealer immediately. 1 Remote controller
2 Wooden screw 4.1 x 16 (2 pieces)
3 Instruction manual
23
Page 26
Lower slot for opening LCD casing
Connection behind
top case
LCD Remote
(Bottom case)
Connection
wires
LCD Remote
(Top case)
2 x Wooden
screw
Connection at
main board
GND
+5V
B A
GND
+5V
B A
b) Step-by-step guide
i) First, open up the casing of the LCD remote controller into its top and bottom case using a screwdriver. To do this, insert the screwdriver into the lower slot and slide it in the outward direction.
ii) Fix the bottom case onto the wall with the 2 wooden screws provided. Then, insert the 4 connecting
wires (from the main board) through the slot on the lower right. iii) Connect one end in each of the 4 wires to the terminal block behind the top case as shown below. The wire that goes into the “GND” terminal at the top case must be connected at the other end to the “GND” terminal at the main board. The same goes for the “+5V”, “B” and “A” connection. iv) Fasten back the top and bottom case into place. Hook the two upper claws into their respective slots and snap the lower part shut.
5) Auto Random Restart
When power is resumed, the unit will automatically restart and operate at the previous setting as before power failure occurred. (Remove jumper at JH/JP1 to cancel the auto random restart function. Please refer to wiring diagram for the location of JH/JP1 Jumper).
24
Page 27
Precaution & Installation
Safety Precautions
Before installing the air conditioner unit, please read the following safety precautions carefully.
WARNING
• Installation and maintenance should be performed by qualied persons who are familiar with local code and regulation, and experienced with this type of appliance.
• All eld wiring must be installed in accordance with the national wiring regulation.
• Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing
wiring work
• According to the wiring diagram.
• The unit must be GROUNDED to prevent possible hazard due to insulation failure.
• All electrical wiring must not touch the refrigerant piping, compressor and any moving parts of the
fan motors.
• Conrm that the unit has been switched OFF before installing or servicing the unit.
Before installing the air conditioner unit, please read the following safety precautions carefully.
CAUTION
Please take note of the following important points when installing
• Do not install the unit where leakage of ammable gas may occur
If gas leaks and accumulates around the unit, it may cause re ignition.
• Conrm drainage piping is connected properly
If the drainage piping is not connected perfectly, it may cause water leakage which will dampen the furniture.
• Do not overcharge the unit
This unit is factory pre-charged. Over charge will cause over current or damage to the compressor.
• Ensure that the unit panel is closed after service or installation.
Unsecured panel will cause unit to operate noisily.
25
Page 28
Installation
ART55A/AR
Air Outlet
Air
Inlet
Air
Inlet
1000
Comp and
Controller
services space
800 800 400
(Min Clearance)
(Min Clearance)
Indoor
Motor
service space
(unit ; mm) All space value ; minimum clearance
All series of air conditioners are designed for outdoor installations and are to be placed on a slab or rooftop. However, if the air conditioner is to be installed in a plant room, please contact your equipment supplier prior to installation for further advise.
Access to the compressors, control wiring, and fans for service and installation purpose must be provided. Please see item 1: Space Required Around Units for recommendations.
1. Space Required Around Units.
(1) Care must be taken to prevent recirculation of air. To stabilize compressor and condensing pressure, it is
recommended that wherever possible the condenser air inlet side should be faced away from prevailing winds. Please see diagrams below.
(2) For rooftop installation, the type of mounting base depends on the construction of the roof. A built-up
roof may not support the weight of the unit. Hence, it may be necessary to support the unit by adding structural members below it.
(3) The units are equipped with hoisting hangers for rigging and hoisting of the unit. Please see item 3:
Lifting method for further information.
The hoisting plates are located on the top of the unit. When hoisting the unit with a crane, spreader bars
must be used to prevent damage to side panels by the supporting cables.
26
Page 29
A(4)RT60/80/100/120 A/AR
Condenser inlet
Electrical control circuit & compressor service
Evaporator coil, air filter service
300
300
700
1000
1500
Condenser outlet
Electrical
control circuit
& compressor
service
Condenser inlet
Condenser inlet
1000
300
700
1000
500
(min clearance)
(min clearance)
condenser outlet
(unit : mm)(unit : mm)
1500
300
Evaporator coil, air filter service
Evaporator coil, air filter service
A(4)RT150/200 A/AR
A(4)RT250/300 A/AR A(4)RT360/420 A/AR
Electrical
control circuit
& compressor
service
Electrical
control circuit
& compressor
service
Condenser inlet
Condenser inlet
Evaporator coil, motor service
1000
500
1000
500
500
500
(min clearance)
(min clearance)
(min clearance)
condenser outlet
2000
Condenser inlet
Condenser inlet
Evaporator coil, motor service
2000
1000
1500
1000
1000
1000
(min clearance)
condenser outlet
(unit : mm)
(unit : mm)
3000
27
Page 30
2. Duct Construction.
Duct connection with a vertical air plenum
Duct connection at ART down flow unit
at ART side flow unit
ART side flow unit
ART down flow unit
Duct connection with a vertical air plenum
Duct connection at ART down flow unit
at ART side flow unit
ART side flow unit
ART down flow unit
(1) Series ART side ow units are equipped with horizontal supply and return air openings. Duct connection to the unit should be made
with duct anges and secured directly to the air openings with exible
duct connectors to avoid normal noise transmission.
(2) For vertical air supply, a eld supply plenum should be used. The gure shows the recommended method for duct connection.
(3) To prevent air leakage, all duct seams should be taped. Duct runs in air spaces that are not air-conditioned must be insulated and provided with a vapor barrier.
Ducts exposed outdoors must be weather proofed. For quiet
operation, we recommend that the insulation on the supply duct be placed inside, lining the duct.
(4) Where ducts from outdoors enter a building, the duct openings in the building should be sealed with weather stripping to prevent rain, dirt, sand, etc. from entering the building.
(5) Correctly sized lters must be tted. There is no provision within the unit for the placement of lter. However, the lters may be installed
in the return air chamber.
(6) Duct earth wiring must be connected. Please refer to the section “Outlines and dimensions” for the correct position.
Optional Feature (Down Flow)*
Series ART down ow units are equipped with vertical supply and
return air openings. Duct connection to the unit should be made with
duct anges to avoid normal noise transmission. When connecting duct earth wiring for down ow conguration, we must use accessory screw attached on the control box cover. * Site modication required. Please refer to item 6:
OPTIONAL FEATURES for details.
28
Page 31
Hook (as directly aligned over the center of gravity as possible)
The drain piping should have a drain trap.
3. Lifting Method.
ART55A ART60A ART80A ART100AART120A ART150A
Refrigerant charge per circuit (kg)
3.65.2 4.05.9 6.22 x 4.5
ART200A ART250A ART300A ART360AART420A
Refrigerant charge per circuit (kg)
2 x 5.92 x 10.52 x 10.416.5 , 19.52 x 19.5
ART55ARART60ARART80AR ART100ARART120ARART150AR
Refrigerant charge per circuit (kg)
3.94.5 4.7 5.66.0 2 x 4.7
ART200AR
ART250ARART300ARART360ARART420AR
Refrigerant charge per circuit (kg)
2 x 5.62 x 10.02 x 9.4 13.5 , 162 x 16.4
A4RT60A
A4RT80A A4RT100A A4RT120A A4RT150A
Refrigerant charge per circuit (kg)
4.64.6 5.95.6 2 x 3.9
A4RT200A
A4RT250A A4RT300A A4RT360A
Refrigerant charge per circuit (kg)
2 x 4.22 x 9.6 2 x 10.4 14.5 , 18.02 x 18.0
A4RT60AR
A4RT80AR
A4RT100ARA4RT120ARA4RT150AR
Refrigerant charge per circuit (kg)
4.35.2 6.06.0 2 x 5.0
A4RT200AR
A4RT250AR
A4RT300ARA4RT360AR
Refrigerant charge per circuit (kg)
2 x 5.82 x 9.4 2 x 9.6 13.5 , 162 x 16
A4RT420A
A4RT420AR
When the unit is to be lifted and moved, attach ropes to the hoisting
hangers (4 pieces) provided on the top corners of the unit.
When the unit is lifted, its center of gravity tends to shift the unit to
one side. Imbalance such as that in the gure should be attained.
The angles at which the ropes suspend the unit should be at least 60º at the compressor end and at least 45º at the condenser end. Care should be taken to avoid contact with the unit while it is being lifted.
4. Drain Piping.
(1) The condensate drain tting (R1) is provided. The drain pipe can
be led out at the right or left side. Please see Chapter 10: Outlines & Dimensions for further details.
(2) The drain pipe must be provided with a trap on the outside of
the unit and also installed at an incline for proper drainage, as shown below.
(3) To prevent condensate formation and leakage, provide the drain
pipe with insulation to safeguard against sweating.
(4) Upon completion of the piping work, check that there is no
leakage and that the water drains off properly.
5. Refrigerant Charge
An additional charge is unnecessary. The table below shows the amount of the charge when the unit is shipped from the factory.
29
Page 32
STEP 1 STEP 3
STEP 2 STEP 4
Remove top panel
Remove service panel
Remove duct flange
Remove duct flange
Remove
Remove low cover
Remove supply air cover
2.Additional casing leg (Accessory parts)
1.Additional side inlet cover (Accessory parts)
Re-install supply air cover
Re-install fan assy
Re-install top panel
Re-install service panel
6. Optional Features (Down Flow) - Site Modication Required.
Reconstruction Method. (From Side Flow To Down Flow) (For A(4)RT80/100/120/150/200A/AR Only)
Series ART side ow units are able to be modied to down ow in the eld with the help of additional accessory items.
The following diagrams show the necessary steps to reconstruct the unit from side ow to down ow.
30
Page 33
7. Special Precautions When Dealing With Refrigerant R407C Unit
(1) What Is New Refrigerant R407C?
R407C is a zeotropic refrigerant mixture which has Zero Ozone Depletion Potential (ODP = 0) and thus,
conforms to the Montreal Protocol regulation. It requires Polyol-ester (POE) oil for its compressor’s lubricant. Its refrigerant capacity and performance are about the same as the refrigerant R22.
(2) Components
Mixture of composition by weight: R32(23%), R125(25%), R134a(52%)
(3) Characteristic
• R407C liquid and vapor components have different compositions when the uid evaporates or condenses. Hence, when a leak occurs and only vapor leaks out, the composition of the
refrigerant mixture left in the system will change and subsequently affect the system performance.
DO NOT add new refrigerant to a leaked system. It is recommended that the system should be evacuated thoroughly before recharging with R407C.
• When refrigerant R407C is used, the composition will differ depending on whether it is in gaseous
or liquid phase. Hence when charging R407C, ensure that only liquid is being withdrawn from the cylinder or can. This is to make certain that only original composition of R407C is being charged into the system.
• POE oil is used as a lubricant for R407C compressor, which is different from the mineral oil used for R22 compressor. Extra precaution must be taken to avoid exposing the R407C system
to moist air.
(4) Check List Before Installation/servicing
• Tubing
Refrigerant R407C is more easily affected by dust of moisture compared with R22, make sure to
temporarily cover the ends of the tubing prior to installation
• Compressor oil
No additional charge of compressor oil is permitted.
• Refrigerant
No other refrigerant other that R407C
• Tools
Tools specically for R407C only (must not be used for R22 or other refrigerant)
i) Gauge manifold and charging hose ii) Gas leak detector iii) Refrigerant cylinder/charging cylinder iv) Vacuum pump c/w adapter v) Flare tools vi) Refrigerant recovery machine
(5) Handling And Installation Guidelines
Like R22 systems, the handling and installation of R407C systems are closely similar. All precautionary
measures; such as ensuring no moisture, no dirt or chips in the system, clean brazing using nitrogen, and thorough leak check and vacuuming are equally important requirements. However, due to the zeotropic nature of R407C and its hydroscopic POE oil, additional precautions must be taken to ensure optimum and trouble-free system operation.
(a) Filter-dryer must be installed along the liquid line for all R407C air conditioners. This is to
minimise the contamination of moisture and dirt in the refrigerant system. Filter-dryer must be of molecular sieve type. For a heat-pump system, install a two-way ow lter dryer along the liquid line.
(b) During installation or servicing, avoid prolong exposure of the internal part of the refrigerant
system to moist air. Residual POE oil in the piping and components can absorb moisture from the air.
31
Page 34
c) Ensure that the compressor is not exposed to open air for more than the recommended time
Composition of R407C in vapour phase
is different from liquid phase.
R32/R125/R134
33% / 33% / 34%
23% / 25% / 52%
Dip-pipe
Invert cylinder without dip-pipe
Liquid withdrawal
specied by its manufacturer (typically less than 10 minutes). Remove the seal-plugs only when the compressor is about to be brazed.
d) The system should be thoroughly vacuumed to 1.0 Pa (-700mmHg) or lower. This vacuuming level is more stringent than R22 system so as to ensure no incompressible gas and moisture in the system.
e) When charging R407C, ensure that only liquid is being withdrawn from the cylinder or can. This is to ensure that only the original composition of R407C is being delivered into the system. The liquid composition can be different from the vapor composition.
f) Normally, the R407C cylinder or can is being equipped with a dip-pipe for liquid withdrawal. However, if the dip -pipe is not available, invert the cylinder or can so as to withdraw liquid from the valve at the bottom.
g) When servicing leaks, the top-up method, commonly practiced for R22 system, is not recommended for R407C systems. Unlike R22 where the refrigerant is of a single component, the composition of R407C (which is made-up of three different components) may have changed during the leak. Consequently, atop-up may not ensure that the R407C in the system is of the original composition. This composition shift may adversely affect the system performance. It is recommended that the system be evacuated thoroughly before recharging with R407C.
32
Page 35
Model Power cable
Breaker capacity
Over current
protection switch
Earth cable
ART55A/AR
4 mm
2
25A 25A
4 mm
2
over
A(4)RT60A/AR
8 mm
2
40A 40A
8 mm
2
over
A(4)RT80A/AR
14 mm
2
50A 50A
14 mm
2
over
A(4)RT100A/AR
14 mm
2
50A 50A
14 mm
2
over
A(4)RT120A/AR
14 mm
2
50A 50A
14 mm
2
over
A(4)RT150A/AR
22 mm
2
100A 100A
22 mm
2
over
A(4)RT200A/AR
22 mm
2
100A 100A
22 mm
2
over
A(4)RT250A/AR
38 mm
2
125A 125A
38 mm
2
over
A(4)RT300A/AR
38 mm
2
125A 125A
38 mm
2
over
A(4)RT360A/AR
38 mm
2
125A 125A
22 mm
2
over
A(4)RT420A/AR
38 mm
2
125A 125A
22 mm
2
over
a. Power supply
b. Main switch/fuse (field supply)
c. Power supply wiring for unit
d. Unit
e. Remote controller
f.
Connection wiring for unit / remote controller (no polarity)
g. Earth
8. Electric Wiring
Construct The Earth Connection.
All electrical work must be carried out by a suitable qualied electrical trades-person and in accordance with
local supply authority requirements and associated regulators. The unit is to be wired directly from an electrical distribution board either by a circuit breaker (preferred) or HRC fuse.
Fix power source wiring to control box by using buffer bushing for sensible force (PG connection or the like). Connect control wiring to control terminal block through the knockout hole of control box using ordinary
bushing.
NOTE : Earth wiring must be connected.
Arrangement such as terminal block in control box.
Method For Connecting Electric Wire
Please carry out the wiring after consulting with local electric power company on local regulations.
(I) The entire wiring diagram of unit.
(II) Electrical wiring Remove the panel on the right side A(4)RT60~120A/AR or the rear side A(4)RT150~420A/AR of the unit
and connect the units power supply wiring to the proper terminals in the control box.
Connect the wires by following the wiring diagram. Mis-connection will damage the controller.
(III) Wiring example and selection of earth leakage breaker
380~415V, 50Hz, 3Ø
The grounding wire must be of the same diameter as the power cable wires. The table above is an example. The selection of other capacities should be determined in accordance with the relevant local standards, in the country of installation.
Note: All electrical wiring must comply with local electrical authority regulations.
33
Page 36
Connector For
Remote Control Wires
Terminal Block For
Power Supply Wires
Connector For
Remote Control Wires
Terminal Block For
Power Supply Wires
connector for remote control
Terminal Block for power supply wire
Control Module Of Unit ART55A/AR
Control Module Of Unit A(4)RT60A
Control Module Of Unit A(4)RT80/100A
34
Page 37
Control Module Of Unit A(4)RT120A
Connector For
Remote Control Wires
Te rminal Block For
Power Supply Wires
Connector For
Remote Control Wires
Terminal Block For
Power Supply Wires
Control Module Of Unit A(4)RT150/200A
35
Page 38
Control Module Of Unit A(4)RT250/300A
Connector For
Remote Control Wires
Terminal Block For
Power Supply Wires
Connector For
Remote Control Wires
Te rminal Block For
Power Supply Wires
Control Module Of Unit A(4)RT60AR
36
Page 39
Control Module Of Unit ART80/100AR
Connector For
Remote Control Wires
Te rminal Block For
Power Supply Wires
Connector For
Remote Control Wires
Terminal Block For
Power Supply Wires
Control Module Of Unit A4RT80/100AR
37
Page 40
Control Module Of Unit A(4)RT120AR
Connector For
Remote Control Wires
Terminal Block For
Power Supply Wires
Connector For
Remote Control Wires
Te rminal Block For
Power Supply Wires
Control Module Of Unit ART150/200AR
38
Page 41
Control Module Of Unit A4RT150/200AR
Connector For
Remote Control Wires
Te rminal Block For
Power Supply Wires
Connector For
Remote Control Wires
Terminal Block For
Power Supply Wires
Control Module Of Unit A(4)RT250/300AR
39
Page 42
Control Module Of Unit A(4)RT360/420A/AR
Terminal Block for
power supply wires
51F1
52F
51C2
TB2 & 3
52C2
52C1
51C1
X1 X2
PCB
52F2
52F3
TB1
47
F1
connector for remote control
wires
(4)RT-AR only
40
Page 43
9. The Putting Condition Of The Belt
Ta ble 1
Parallel angle
pulley
10 or less
Gap of 3mm every 1m
Ta ble 2
mm inch 60-802.5-3.0 81-903.5
91-1054
106-above 4.5-above
1.6-2.0
1.9-2.9
Size of Pulley Motor
K(i)note
pulley
Flexion load
W(kgf)
1.1-1.4
1.3-1.7
1. Set the parallel angle of the fan and the motor pulley as shown in table 1 and gure 1.
2. Set the tension of one belt when the exion load is within the range as shown in gure 2 and table 2
at the proper exion. (A=0.016xC mm)
3. Adjust the suitable tension after the belt sit properly across the pulley (after working for 24-28 hours).
When a new belt is used, adjust the suitable tension about 1.3 times the maximum value of the exion load.
4. Readjust the belt every 2,000 hours after the rst adjustment. Exchange the belt when the belt’s surroundings length has expanded by 2% including the rst
expansion (about 1%) of the belt (after approximately 8,000 hours converted working time).
10. Before Starting The Trial Run
After having installed the unit, check that :
(1) The unit is xed securely.
(2) The unit is installed properly. (3) The drain pipe is provided with a drain trap. (4) The electrical wiring has been connected correctly and the terminal screws have been properly tightened. (5) The duct work has been performed correctly.
Before turning the unit on: (1) Measure the resistance between the terminals of the electrical parts and ground to ensure that the value is at least 1.0M ohm. If the measured value is below 1.0M ohm, do not operate the unit. (2) The unit is using a phase protector. If wiring phase of power supply is mistaken, the unit does not run.
Please reconrm and modify wiring phase.
After the unit is turned on: (1) Check that the fans are rotating in the proper direction. (2) Check to see whether there are refrigerant leakage, and slack in power or transmission cable. (3) Check the operation of high-pressure switch. If the two lead wires of the outdoor unit fan motor are disconnected from the contactor and cooling is performed, the high-pressure switch should function and stop the unit after 5 to 10 minutes. Perform trial operation after completion of above items.
41
Page 44
11. Before Operating The Unit
Ground
Obstacle blocking air inlet
Ceiling
Inlet grille
Ceiling
Outlet grille
Obstacle blocking air outlet
1. Check points for operation Check the following points before you operate your air conditioner.
(1) Check that there is nothing blocking the ow of air from the air outlet into the air inlet.
Indoor Side
Outdoor Side
(2) Make sure the air conditioner is properly grounded by checking the ground terminal.
2. Caution for use
Keep the following points in mind to safeguard against failures and breakdowns.
• For safety, conrm that the earth terminal has been connected to the earth wire correctly.
• Never block or cover the unit’s intakes or outlets. It will reduce the unit’s efciency.
• To start the unit again after it is stopped, ensure 3 minutes has elapsed before turning the
unit ON. Repeated stopping and starting within 3 minutes gives improper force to the machine. This can cause the fuse or power source to trip.
42
Page 45
Overall Noise
125Hz 250Hz 500Hz 1kHz 2kHz 4kHz 8kHz (dBA) Criteria
ART55A/AR 73 72 65 62 58 52 44 68 66
A(4)RT60A/AR 67 61 59 60 55 49 42 63 59
A(4)RT80A/AR 68 65 64 62 54 49 39 65 61
A(4)RT100A/AR 69 67 64 60 56 51 42 66 58
A(4)RT120A/AR 68 64 62 65 60 53 45 68 64
A(4)RT150A/AR 74 68 68 67 60 53 44 70 66
A(4)RT200A/AR 74 69 67 66 60 52 43 70 65
A(4)RT250A/AR 76 72 70 71 65 55 46 74 70*
A(4)RT300A/AR 77 72 71 72 65 55 46 74 71*
A(4)RT360A/AR 67 74 74 75 76 69 60 80 > 70*
A(4)RT420A/AR 72 76 76 75 75 69 58 80 > 70*
Model
1/1 Octave Sound Pressure Level (dB, ref 20 µPa)
* THE DATA DOES NOT APPLY TO INDOOR NOISE CRITERION. Note:
1. ART55A/AR, A(4)RT80A/AR, A(4)RT100A/AR, A(4)RT150A/AR and A(4)RT200A/AR
- Microphone position: 1 m in front of the unit and 1 m above the floor.
2. A(4)RT60A/AR, A(4)RT120A/AR, A(4)RT250A/AR, A(4)RT300A/AR, A(4)RT360A/AR, and A(4)RT420A/AR
- Microphone position: 1 m from the service panel and 1 m height from the floor level.
ART55A/AR NC CURVES
10
20
30
40
50
60
70
80
125
250 500 1000 2000 4000 8000
Octave-band frequency (Hz)
Sound pressure level (dB, ref 20µPa)
NC70
NC45
NC50
NC55
NC60
NC65
NC20
NC25
NC30
NC35
NC40
4. SOUND DATA
43
Page 46
A(4)RT80A/AR NC CURVES
0
10
20
30
40
50
60
70
80
125 250 500 1000 2000 4000 8000
Octave-band frequency (Hz)
NC-20
NC-30
NC-25
NC-35
NC-40
NC-45
NC-50
NC-55
NC-60
NC-65
A(4)RT60A/AR NC CURVES
0
10
20
30
40
50
60
70
80
125 250 500 1000 2000 4000 8000
Octave-band frequency (Hz)
NC-20
NC-30
NC-25
NC-35
NC-40
NC-45
NC-50
NC-55
NC-60
Sound pressure level (dB, ref 20µPa) Sound pressure level (dB, ref 20µPa)
44
Page 47
A(4)RT100A/AR NC CURVES
0
10
20
30
40
50
60
70
80
125 250 500 1000 2000 4000 8000
Octave-band frequency (Hz)
NC-20
NC-30
NC-25
NC-35
NC-40
NC-45
NC-50
NC-55
NC-60
A(4)RT120A/AR NC CURVES
0
10
20
30
40
50
60
70
80
125 250 500 1000 2000 4000 8000
Octave-band frequency (Hz)
Sound pressure level (dB, ref 20µPa)Sound pressure level (dB, ref 20µPa)
NC-20
NC-30
NC-25
NC-35
NC-40
NC-45
NC-50
NC-55
NC-60
NC-65
45
Page 48
A(4)RT150A/AR NC CURVES
0
10
20
30
40
50
60
70
80
90
125 250 500 1000 2000 4000 8000
Octave-band frequency (Hz)
Octave-band frequency (Hz)
NC-20
NC-30
NC-25
NC-35
NC-40
NC-45
NC-50
NC-55
NC-60
NC-65
NC-70
A(4)RT 200A/AR NC CURVES
0
10
20
30
40
50
60
70
80
125 250 500 1000 2000 4000 8000
Sound pressure level (dB, ref 20µPa) Sound pressure level (dB, ref 20µPa)
NC-20
NC-30
NC-25
NC-35
NC-40
NC-45
NC-50
NC-55
NC-60
NC-65
46
Page 49
A(4)RT 360A/AR NC CURVES
Octave-band frequency (Hz)
A(4)RT 420A/AR NC CURVES
10
20
30
40
50
60
70
80
125 250500 1000 2000 4000 8000
NC70
NC45
NC50
NC55
NC60
NC65
NC20
NC25
NC30
NC35
NC40
Sound pressure level (dB, ref 20mPa) Sound pressure level (dB, ref 20mPa)
Octave-band frequency (Hz)
10
20
30
40
50
60
70
80
NC70
NC45
NC50
NC55
NC60
NC65
NC20
NC25
NC30
NC35
NC40
125 250 500 1000 2000 4000 8000
47
Page 50
A(4)RT 360A/AR NC CURVES
Octave-band frequency (Hz)
A(4)RT 420A/AR NC CURVES
10
20
30
40
50
60
70
80
125 250500 100020004000 8000
NC
70
NC
45
NC
50
NC
55
NC
60
NC
65
NC
20
NC
25
NC
30
NC
35
NC
40
Sound pressure level (dB, ref 20mPa)
Octave-band frequency (Hz)
10
20
30
40
50
60
70
80
125250 500 1000 2000 4000 8000
NC70
NC45
NC50
NC55
NC60
NC65
NC20
NC25
NC30
NC35
NC40
Sound pressure level (dB, ref 20mPa)
48
Page 51
Note: Factory supplied rooftop is only with standard drive package. All other changes are only given as example and need to be field supply.
5. SELECTION PROCESS
110
106
Drive Package
The following are the design requirements for ART100A unit:
Model: ART100A
Supply Air Quantity=3800 CFM External Static Pressure = 150 Pa
Step 1: From the blower curve (at 3800 CFM),
Standard operating system;
Internal Static Pressure = 160 Pa
Step 2: Therefore at 3800 CFM and 150 Pa external static pressure,
To tal Static Pressure = 150 + 160 Pa
= 310 Pa
Step 3: From the blower curve, the design requirement calls for RPM about 1380 RPM.
From the table:
Motor pulley =106 mm
Blower pulley = 125 mm
Motor RPM= 1420
In order to obtain 1380 RPM, we calculate the new blower pulley as: (while maintaining the motor pulley)
Db = x (1420/1380)
= 109.1 mm
Let us take close approximation of 110 mm diameter pulley size
Recheck, with Db = 110 mm
Blow pulley = 1420 x (106/110)
= 1368.4 RPM
We thus need to change the blower pulley from 125 mm to 110 mm in order to obtain the higher operating static pressure.
Step 3: When the pulley is changed, the V-belt length must be rechecked. We have for horizontal air throw
configuration:
V-belt length, L =2C + 1.57 (Db + Dm)
=(2 x 174) + 1.57(110 + 106) = 687.12
We thus can use a belt with a length of 687 mm.
where, C = distance between the centres of the two pulleys
Db = diameter of blower pulley
Dm = diameter of motor pulley
Step 4: From the blower curve, we can also notice that the motor power input not maintained within the current
operating range of the standard unit's motor.
Summary:
i) Fan motor kW = 2.2 kW ii) Blower pulley diameter = 110 mm iii) V-belt size=687 mm
49
Page 52
DIMENSIONALDATA
Below tables summarizes the pulley data, motor size used for the RT series, as manufactured.
Model
ART55A/AR SPZ1 100 SPZ1 63 SPZ 1000
A(4)RT60A/AR SPZ1 125 SPZ1 95 SPZ 750
A(4)RT80A/AR SPZ1 140 SPZ1 100 SPZ 737
A(4)RT100A/AR SPZ1 125 SPZ1 106 SPZ 710
A(4)RT120A/AR SPZ1 125 SPZ1 106 SPZ 710
A(4)RT150A/AR SPA2 160 SPA2 90 SPA 782
A(4)RT200A/AR SPA2 170 SPA2 100 SPA 757
A(4)RT250A/AR SPZ2 224 SPZ2 125 SPZ 1662
A(4)RT300A/AR SPZ2 224 SPZ2 140 SPZ 1700
A(4)RT360A/AR SPA 280 VPT 124 SPA 2132
BlowerPulley,Db MotorPulley,Dm VBelt
Type Diameter(mm) Type Diameter(mm) Type Length(mm)
A(4)RT420A/AR SPA 250 VPT 118 SPA 2060
Model
PulleyCenterDistance,C(mm) Motor
Nom Min Max kw RPM
ART55A/AR 850 920 1015 0.75 1420
A(4)RT60A/AR 203 203 245 0.75 1420
A(4)RT80A/AR 180 175 190 1.1 1420
A(4)RT100A/AR 174 170 185 1.5 1420
A(4)RT120A/AR 174 170 185 1.5 1420
A(4)RT150A/AR 195 190 205 2.2 1430
A(4)RT200A/AR 167 165 180 3.7 1430
A(4)RT250A/AR 558 558 572 5.5 1440
A(4)RT300A/AR 565 558 572 7.5 1440
A(4)RT360A/AR 748 730 763 7.5 1440
A(4)RT420A/AR 739 730 763 7.5 1440
50
Page 53
Blower Curve
ART55A/AR
Air Flow
52
Page 54
A(4)RT60A/AR
Total Static Pressure
Air Flow
53
Page 55
$(4)RT080A/AR
)aP( erusserP citatS latoT
350
300
250
200
1.5 kW
1.1 kW
Standard Point
MPR
1300
1200
1100
150
Internal Static Pressure
1000
100
900
50
0
2800 2900 3000 3100 3200 3300 CFM
1320 1400 1500 1560 L/S
Air Flow
54
Page 56
$(4)RT100A/AR
)aP( erusserP citatS latoT
400
350
300
250
1.5 kW
1.1 kW
Standard
Point
2.2 kW
MPR
1400
1300
200
150
100
50
Internal Static Pressure
1200
1100
1000
0
3100 3200 3300 3400 3500 3600 3700 3800 3900 4000 4100 CFM
1470 1500 1600 1700 1800 1900 1930 L/S
Air Flow
55
Page 57
$(4)RT120A/AR
)aP( erusserP citatS latoT
400
350
300
250
1.5 kW
1.1 kW
Standard
Point
2.2 kW
MPR
1400
1300
200
150
100
50
Internal Static Pressure
1200
1100
1000
0
3100 3200 3300 3400 3500 3600 3700 3800 3900 4000 4100 CFM
1470 1500 1600 1700 1800 1900 1930 L/S
Air Flow
56
Page 58
$(4)RT150A/AR
500
450
400
350
300
250
2.2 kW
1.5kW
3.0 kW
RPM
1000
900
Standard
Point
800
700
200
Internal
600
Static
150
100
50
0
4600 4800 5000 5200 5400 5600 5800 6000 6200 CFM
2170 2200 2400 2600 2800 2926 L/S
Pressure
Air Flow
Page 59
$(4)RT200A/AR
Air Flow
650
600
550
500
450
5.5 kW
3.7 kW
1200
Standard Point
RPM
1100
1000
400
3.0kW
900
Total Static Pressure (Pa)
350
800
Internal
300
250
700
200
Static Pressure
150
5600 5800 6000 6200 6400 6600 6800 7000 7200 CFM
2640 2800 3000 3200 3400 L/s
Page 60
Air Flow
A(4)RT250A/AR
59
Page 61
A(4)RT300A/AR
Air Flow
60
Page 62
0
100
200
300
400
500
600
700
800
900
9000 9500 10000 10500 1100011500 12000 12500
Air Flow (CFM)
Total Static Pressure (Pa)
600
700
800
Standard Point
Fan Speed (rpm)
7.5kw
5.5kw
500
Internal Static Pressure
4.0kw
A(4)RT360A/AR
61
Page 63
Air Flow (CFM)
100
200
300
400
500
600
700
800
900
1000
10500 1100011500 12000 12500 13000 1350014000 14500 15000
Total Static Pressure (Pa)
600
700
800
Standard Point
Fan Speed (rpm)
7.5kw
5.5kw
11.0kw
500
Internal Static Pressure
A(4)RT420A/AR
62
Page 64
General Data - Cooling Only (R22)
General Data - Cooling Only (R22)
Btu/h
W
W
A
V/Ph/Hz
W/W
AIR DISCHARGE
OPERATION
AIR FLOW l/s / cfm
EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm
dBA mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb kg/lb
220 / 484
3.5 / 7.7
2.48
1430 / 56.3
916 / 36
1090 / 43
1110 / 43.7
1386 / 55
380 ~ 415 / 3 / 50
REFRIGERANT TYPE / CONTROL
19 / 0.75
ART55A
850 / 1800
11.0
54000
15830
6380
R22 / TXV
98 / 0.39
SLM CONTROLLER
EVAPORATOR
DUCTED
CONDENSATE DRAIN SIZE
1045 / 41.1
2124 / 4500
68
CONDENSER
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
HEIGHT
WIDTH
MODEL
UNIT DIMENSION
SOUND PRESSURE LEVEL
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
NOMINAL CAPACITY
EER
CONTROL
AIR FLOW
POWER SOURCE
REFRIGERANT CHARGE
DEPTH
UNIT WEIGHT
1) ALL SPECIFICATIONS A RE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO
ISO 13253
.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
Btu/h
59000 80000
W 17290 23450
W 5610 8100
A 10.4 15.4
V/Ph/Hz
R22 / TXV R22 / CAPILLARY TUBE
W/W 3.08 2.43
AIR DISCHARGE
OPERATION
AIR FLOWl/s / cfm 850 / 1800 1334 / 2826
EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm 2124 / 4500 2667 / 5650
dBA 63 65
mm/in mm/in 1100 / 43.3 1300 / 51.2 mm/in mm/in mm/in
1250 / 49.2
1450 / 57.1
mm/in
kg/lb 295 / 650 370 / 816 kg/lb 5.2 / 11.54.0 / 8.8
EER
DEPTH
UNIT WEIGHT
98 / 0.39
SLM CONTROLLER
1680 / 66.1
HEIGHT
SOUND PRESSURE LEVEL
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
AIR FLOW
CONDENSER
WIDTH
REFRIGERANT CHARGE
POWER SOURCE
REFRIGERANT TYPE / CONTROL
NOMINAL CAPACITY
1530 / 60.2 1090 / 42.9
UNIT DIMENSION
1000 / 39.4
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
ART60AMODEL
EVAPORATOR
DUCTED
CONDENSATE DRAIN SIZE
ART80A
380 ~ 415 / 3 / 50
CONTROL
25.4 / 1
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
6. ENGINEERING & PHYSICAL DATA
Specications
63
Page 65
General Data - Cooling Only (R22)
General Data - Cooling Only (R22)
Btu/h 100000 116000
W 29300 34000
W 10500 11560
A 18.2 22.1
V/Ph/Hz
R22 / CAPILLARY TUBE R22 / TXV
W/W 2.94 2.94
AIR DISCHARGE OPERATION
AIR FLOWl/s / cfm 1667 / 3532 1699 / 3600
EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm 2667 / 5650 3776 / 8000
dBA 66 68
mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 400 / 882 425 / 937
kg/lb 5.9 / 136.2 / 13.7
NOMINAL CAPACITY
98 / 0.39
SLM CONTROLLER
EVAPORATOR
DUCTED
CONDENSATE DRAIN SIZE
REFRIGERANT TYPE / CONTROL
EER
1680 / 66.1
ART120A
380 ~ 415 / 3 / 50
1000 / 39.4 1300 / 51.2
1450 / 57.1
25.4 / 1
ART100A
1530 / 60.2 1090 / 42.9
CONDENSER
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
HEIGHT
WIDTH
REFRIGERANT CHARGE
DEPTH
UNIT WEIGHT
MODEL
UNIT DIMENSION
SOUND PRESSURE LEVEL
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
CONTROL
AIR FLOW
POWER SOURCE
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
Btu/h 150000 200000
W 44000 58600
W 15600 20700
A 29.0 35.7
V/Ph/Hz
W/W 2.51 2.58
AIR DISCHARGE
OPERATION
AIR FLOW l/s / cfm 2667 / 5651 3167 / 6710
EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm
dBA mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 665 / 1466 765 / 1687 kg/lb 2 x 4.5 / 2 x 9.9 2 x 5.9 / 2 x 13
AIR FLOW 5333 / 11300
70
25.4 / 1
ART200A
380 ~ 415 / 3 / 50
CONTROL
MODEL
POWER SOURCE
NOMINAL CAPACITY
NOMINAL TOTAL INPUT POWER
REFRIGERANT TYPE / CONTROL
UNIT WEIGHT
UNIT DIMENSION
SOUND PRESSURE LEVEL
1200 / 47.2
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
HEIGHT
WIDTH
CONDENSER
ART150A
1670 / 65.7 1320 / 52.0
1810 / 71.3
1990 / 78.4
2100 / 82.7
REFRIGERANT CHARGE
DEPTH
NOMINAL RUNNING CURRENT
EER
R22 / CAPILLARY TUBE
196 / 0.79
SEQUENTIAL CONTROLLER
EVAPORATOR
DUCTED
CONDENSATE DRAIN SIZE
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
64
Page 66
General Data - Cooling Only (R22)
General Data - Cooling Only (R22)
Btu/h 250000 300000
W 73270 87930
W 27560 35960
A 49.6 62.7
V/Ph/Hz
W/W 2.56
2.39
AIR DISCHARGE
OPERATION
AIR FLOW l/s / cfm 3776 / 8000 4531 / 9600
EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm
dBA mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 1200 / 2646 1350 / 2976 kg/lb 2 x 10.5 / 2 x 23.12 x 10.4 / 2 x 22.9
2250 / 88.5
2250 / 88.5
NOMINAL CAPACITY
294 / 1.18
SEQUENTIAL CONTROLLER
EVAPORATOR
DUCTED
CONDENSATE DRAIN SIZE
CONDENSER
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
HEIGHT
WIDTH
REFRIGERANT CHARGE
DEPTH
UNIT WEIGHT
ART250A
2800 / 110.0
1900 / 75
2900 / 114
UNIT DIMENSION
SOUND PRESSURE LEVEL
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
ART300A
380 ~ 415 / 3 / 50
CONTROL
MODEL
REFRIGERANT TYPE / CONTROL EER
R22 / TXV
74
1735 / 68.0
AIR FLOW
POWER SOURCE
9439 / 20000
25.4 / 1
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
Btu/h
329000 404000
W
96420 118410
W 39870 46800 A 67.2 72.8
V/Ph/Hz
W/W 2.42 2.53
AIR DISCHARGE
OPERATION
AIR FLOWl/s / cfm 5191 / 11000 5899 / 12500
EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm
dBA mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 1510 / 3329 1600 / 3527
kg/lb 16.5 / 36.4 & 19.5 / 43.02 x 19.5 / 2 x 43.0
MODEL
70
AIR FLOW
POWER SOURCE
9439 / 20000
25.4 / 1
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
WIDTH
REFRIGERANT CHARGE
DEPTH
UNIT WEIGHT
REFRIGERANT TYPE / CONTROL EER
ART360A
3180 / 125.0
CONTROL
CONDENSER
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
2150 / 84.5
3250 / 128.0
ART420A
380 ~ 415 / 3 / 50
1974 / 78.0 2252 / 89.0
2300 / 90.5
R22 / TXV
HEIGHT
NOMINAL CAPACITY
294 / 1.18
SEQUENTIAL CONTROLLER
EVAPORATOR
DUCTED
CONDENSATE DRAIN SIZE
UNIT DIMENSION
SOUND PRESSURE LEVEL
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
65
Page 67
General Data - Heat pump (R22)
General Data - Heat pump (R22)
Btu/h
W
Btu/h
W W W A A
V/Ph/Hz
W/W
W/W AIR DISCHARGE OPERATION
AIR FLOWl/s / cfm EXTERNAL STATIC PRESSURE
Pa/in.wg.
mm/in
l/s / cfm
dBA mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb kg/lb
REFRIGERANT TYPE / CONTROL
R22 / TXV (HEATING), CAP TUBE (COOLING)
EER COP
2.93
19./ 0.75
916 / 36
1386 /55
1045/ 41.1
1090 / 43
1650/3500
5128
10.2
9.4
850 / 1800
380 ~ 415 / 3 / 50
98 / 0.39
DUCTED
3.41
ART55AR
55000 16119
NOMINAL RUNNING CURRENT (HEATING)
NOMINAL TOTAL INPUT POWER (COOLING) NOMINAL TOTAL INPUT POWER (HEATING) NOMINAL RUNNING CURRENT (COOLING)
56500 16559
5778
POWER SOURCE
MODEL
CONTROL
EVAPORATOR*
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
CONDENSATE DRAIN SIZE
SOUND PRESSURE LEVEL
CONDENSER*
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
HEIGHT
WIDTH
230 / 506
REFRIGERANT CHARGE
AIR FLOW
DEPTH
UNIT WEIGHT
1430 / 56.3
1110 /43.7
68
3.9 / 8.6
UNIT DIMENSION
SLM CONTROLLER
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) * DESIGNATION BASED ON COOLING CYCLE.
6) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STA NDARD: ISO 13253
Btu/h
56000 80000
W
16410 23450
Btu/h
68000 78600
W
19930 23000
W
6220 9400
W
5970 7800
A
12.7 16.8
A
12.4 14.8
V/Ph/Hz
R22 / TXV R22 / CAPILLARY TUBE
W/W
2.64 1.73
W/W
3.34 2.98
AIR DISCHARGE OPERATION
AIR FLOWl/s / cfm
850 / 1800 1334 / 2826
EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm
2124 / 4500 2667 / 5650
dBA
63 65
mm/in mm/in
1100 / 43.3 1300 / 51.2
mm/in mm/in mm/in
1250 / 49.2
1450 / 57.1
mm/in
kg/lb
320 / 705 385 / 849
kg/lb
4.5 / 9.9 4.7 / 10.4
1680 / 66.1
25.4 / 1
1000 / 39.4
1530 / 60.2 1090 / 42.9
ART60AR ART80AR
380 ~ 415 / 3 / 50
98 / 0.39
DUCTED
SLM CONTROLLER
NOMINAL RUNNING CURRENT (HEATING) POWER SOURCE REFRIGERANT TYPE / CONTROL EER COP
MODEL
CONTROL
EVAPORATOR*
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER (COOLING) NOMINAL TOTAL INPUT POWER (HEATING) NOMINAL RUNNING CURRENT (COOLING)
CONDENSATE DRAIN SIZE
UNIT DIMENSION
SOUND PRESSURE LEVEL
CONDENSER*
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
HEIGHT
WIDTH
REFRIGERANT CHARGE
AIR FLOW
DEPTH
UNIT WEIGHT
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) * DESIGNATION BASED ON COOLING CYCLE.
6) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
66
Page 68
General Data - Heat pump (R22)
General Data - Heat pump (R22)
Btu/h 100000 105000
W
29300 30770
Btu/h
105000 118000
W
30800
32580
W
11860
11600
W
10050
10700
A
20.5
21.6
A
18.2
21.0
V/Ph/Hz
R22 / CAPILLARY TUBE R22 / TXV
W/W 2.03 2.65 W/W 2.67 3.23
AIR DISCHARGE OPERATION
AIR FLOW l/s / cfm 1667 / 3532 1699 / 3600 EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm 2667 / 5650 4719 / 10000
dBA 66 68
mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 415 / 915 440 / 970 kg/lb 5.6 / 12.36.0 / 13.2
REFRIGERANT CHARGE
AIR FLOW
DEPTH
UNIT WEIGHT
CONDENSATE DRAIN SIZE
UNIT DIMENSION
SOUND PRESSURE LEVEL
CONDENSER*
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
HEIGHT
WIDTH
MODEL
CONTROL
EVAPORATOR*
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER (COOLING) NOMINAL TOTAL INPUT POWER (HEATING) NOMINAL RUNNING CURRENT (COOLING) NOMINAL RUNNING CURRENT (HEATING) POWER SOURCE REFRIGERANT TYPE / CONTROL EER COP
ART100AR ART120AR
380 ~ 415 / 3 / 50
98 / 0.39
DUCTED
SLM CONTROLLER
1680 / 66.1
25.4 / 1
1000 / 39.4
1530 / 60.2 1090 / 42.9
1300 / 51.2
1450 / 57.1
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) * DESIGNATION BASED ON COOLING CYCLE.
6) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
Btu/h
150000 200000
W
44000 58600
Btu/h 155000
208000
W 45400
61000
W 18600 23500 W 15400 20400
A 33.0 39.2 A 29.0 35.0
V/Ph/Hz
W/W 2.26
2.19
W/W 3.02 2.80
AIR DISCHARGE OPERATION
AIR FLOWl/s / cfm 2667 / 5651
3167 / 6710
EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm
dBA mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 700 / 1543
800 / 1764
kg/lb 2 x 4.7 / 2 x 10.4
2 x 5.6 / 2 x 12.3
1938 / 76.3
25.4 / 1
1200 / 47.2
1800 / 70.9 1320 / 52.0
1990 / 78.4
2100 / 82.7
5333 / 11300
70
ART150AR ART200AR
380 ~ 415 / 3 / 50
196 / 0.79
DUCTED
SEQUENTIAL CONTROLLER
R22 / CAPILLARY TUBE
NOMINAL RUNNING CURRENT (HEATING) POWER SOURCE REFRIGERANT TYPE / CONTROL EER COP
MODEL
CONTROL
EVAPORATOR*
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER (COOLING) NOMINAL TOTAL INPUT POWER (HEATING) NOMINAL RUNNING CURRENT (COOLING)
CONDENSATE DRAIN SIZE
UNIT DIMENSION
SOUND PRESSURE LEVEL
CONDENSER*
PACKING DIMENSION
HEIGHT
WIDTH
DEPTH
HEIGHT
WIDTH
REFRIGERANT CHARGE
AIR FLOW
DEPTH
UNIT WEIGHT
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) * DESIGNATION BASED ON COOLING CYCLE.
6) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
67
Page 69
General Data - Heat pump (R22)
General Data - Heat pump (R22)
Btu/h 235000 290000
W 68880 84990
Btu/h 252000 295000
W 73860 86460 W 27660 37160 W 26360 32660
A 49.9 64.7 A 48.1 59.1
V/Ph/Hz
W/W 2.37 2.23
W/W 2.68 2.53
AIR DISCHARGE OPERATION
AIR FLOW l/s / cfm 3776 / 8000 4531 / 9600 EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm
dBA mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb
1200 / 2646
1350 / 2976
kg/lb
2 x 10 / 2 x 22
2 x 9.4 / 2 x 20.7
REFRIGERANT CHARGE
AIR FLOW
DEPTH
UNIT WEIGHT
CONDENSATE DRAIN SIZE
UNIT DIMENSION
SOUND PRESSURE LEVEL
CONDENSER*
PACKING DIMENSION
HEIGHT
WIDTH
DEPTH
HEIGHT
WIDTH
MODEL
CONTROL
EVAPORATOR*
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER (COOLING) NOMINAL TOTAL INPUT POWER (HEATING) NOMINAL RUNNING CURRENT (COOLING) NOMINAL RUNNING CURRENT (HEATING) POWER SOURCE REFRIGERANT TYPE / CONTROL EER COP
ART250AR ART300AR
380 ~ 415 / 3 / 50
294 / 1.18
DUCTED
SEQUENTIAL CONTROLLER
R22 / TXV
2900 / 114
25.4 / 1
1735 / 68.0
2800 / 110.0
1900 / 75
2250 / 88.5
2250 / 88.5
9439 / 20000
74
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) * DESIGNATION BASED ON COOLING CYCLE.
6) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
Btu/h 335000 384000
W 98180 112540
Btu/h 348000 412000
W 101990 120750 W 39210 46400 W 35830 40800
A 70.6 72.5 A 66.6 65.3
V/Ph/Hz
W/W 2.50 2.43 W/W 2.85 2.96
AIR DISCHARGE OPERATION
AIR FLOW l/s / cfm
5191 / 11000 5899 / 12500
EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm
dBA mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb
1510 / 3329 1600 / 3527
kg/lb
13.5/ 29.7 & 16 / 36.22 x 16.4 / 2 x 36.2
9439 / 20000
70
EER COP
ART360AR ART420AR
380 ~ 415 / 3 / 50
294 / 1.18
DUCTED
SEQUENTIAL CONTROLLER
R22 / TXV
NOMINAL RUNNING CURRENT (COOLING) NOMINAL RUNNING CURRENT (HEATING) POWER SOURCE REFRIGERANT TYPE / CONTROL
DEPTH
MODEL
CONTROL
EVAPORATOR*
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER (COOLING) NOMINAL TOTAL INPUT POWER (HEATING)
2252 / 89.0
CONDENSER*
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
HEIGHT
WIDTH
REFRIGERANT CHARGE
AIR FLOW
UNIT WEIGHT
3250 / 128.0
2300 / 90.5
CONDENSATE DRAIN SIZE
UNIT DIMENSION
SOUND PRESSURE LEVEL
25.4 / 1
1974 / 78.0
3180 / 125.0
2150 / 84.5
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) * DESIGNATION BASED ON COOLING CYCLE.
6) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STA NDARD: ISO 13253
68
Page 70
General Data - Cooling Only (R407C)
General Data - Cooling Only (R407C)
Btu/h 59000 72000
W 17290 21100
W 5890 8700
A 10.9 16.3
V/Ph/Hz
R407C / TXV R407C / CAPILLARY TUBE
W/W 2.94 2.32
AIR DISCHARGE
OPERATION
AIR FLOWl/s / cfm 850 / 1800 1334 / 2826
EXTERNAL STATIC PRESSURE (H/M/L) Pa/in.wg.
mm/in
l/s / cfm 2124 / 4500 2667 / 5650
dBA 63 65
mm/in mm/in 1100 / 43.3 1300 / 51.2 mm/in mm/in mm/in
1250 / 49.2
1450 / 57.1
mm/in
kg/lb 295 / 650 370 / 816 kg/lb
4.6 / 10.1
4.6 / 10.1
EER
DEPTH
UNIT WEIGHT
98 / 0.39
SLM CONTROLLER
1680 / 66.1
HEIGHT
SOUND PRESSURE LEVEL
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
AIR FLOW
CONDENSER
WIDTH
REFRIGERANT CHARGE
POWER SOURCE
REFRIGERANT TYPE / CONTROL
NOMINAL CAPACITY
1530 / 60.2 1090 / 42.9
UNIT DIMENSION
1000 / 39.4
PACKING DIMENSION
HEIGHT
WIDTH
DEPTH
A4RT60AMODEL
EVAPORATOR
DUCTED
CONDENSATE DRAIN SIZE
A4RT80A
380 ~ 415 / 3 / 50
CONTROL
25.4 / 1
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPA CITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
Btu/h 95000 110000
W 27840 32240
W 11600 12180
A 20.2 22.8
V/Ph/Hz
R407C / CAPILLARY TUBE R407C / TXV
W/W 2.31 2.65
AIR DISCHARGE
OPERATION
AIR FLOW l/s / cfm 1667 / 3532 1699 / 3600
EXTERNAL STATIC PRESSURE (H/M/L) Pa/in.wg.
mm/in
l/s / cfm 2667 / 5650 3776 / 8000
dBA 66 68
mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 400 / 882 425 / 937 kg/lb 5.9 / 135.6 / 12.3
NOMINAL CAPACITY
98 / 0.39
SLM CONTROLLER
EVAPORATOR
DUCTED
CONDENSATE DRAIN SIZE
REFRIGERANT TYPE / CONTROL
EER
1680 / 66.1
A4RT120A
380 ~ 415 / 3 / 50
1000 / 39.4 1300 / 51.2
1450 / 57.1
25.4 / 1
A4RT100A
1530 / 60.2 1090 / 42.9
CONDENSER
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
HEIGHT
WIDTH
REFRIGERANT CHARGE
DEPTH
UNIT WEIGHT
MODEL
UNIT DIMENSION
SOUND PRESSURE LEVEL
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
CONTROL
AIR FLOW
POWER SOURCE
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STA NDARD: ISO 13253
69
Page 71
General Data - Cooling Only (R407C)
General Data - Cooling Only (R407C)
Btu/h 140000 190000
W 41030 55680
W 17200 25100
A 32.1 43.8
V/Ph/Hz
W/W 2.34 2.18
AIR DISCHARGE
OPERATION
AIR FLOWl/s / cfm 2667 / 5651 3167 / 6710
EXTERNAL STATIC PRESSURE (H/M/L) Pa/in.wg.
mm/in
l/s / cfm
dBA
mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 665 / 1466 765 / 1687 kg/lb
2 x 3.9 / 2 x 8.6
2 x 4.2 / 2 x 9.3
AIR FLOW 5333 / 11300
70
25.4 / 1
A4RT200A
380 ~ 415 / 3 / 50
CONTROL
MODEL
POWER SOURCE
NOMINAL CAPACITY
NOMINAL TOTAL INPUT POWER
REFRIGERANT TYPE / CONTROL
UNIT WEIGHT
UNIT DIMENSION
SOUND PRESSURE LEVEL
1200 / 47.2
PACKING DIMENSION
HEIGHT
WIDTH
DEPTH
HEIGHT
WIDTH
CONDENSER
A4RT150A
1670 / 65.7 1320 / 52.0
1810 / 71.3
1990 / 78.4
2100 / 82.7
REFRIGERANT CHARGE
DEPTH
NOMINAL RUNNING CURRENT
EER
R407C / CAPILLARY TUBE
196 / 0.79
SEQUENTIAL CONTROLLER
EVAPORATOR
DUCTED
CONDENSATE DRAIN SIZE
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STA NDARD: ISO 13253
Btu/h 230000 283000
W 67410 82940
W 28700 40160
A 53.0 68.5
V/Ph/Hz
W/W 2.21.96
AIR DISCHARGE
OPERATION
AIR FLOW l/s / cfm 3776 / 8000 4389 / 9300
EXTERNAL STATIC PRESSURE (H/M/L) Pa/in.wg.
mm/in
l/s / cfm
dBA
mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 1200 / 2646 1350 / 2976 kg/lb 2 x 9.6 / 2 x 21.22 x 10.4 / 2 x 22.9
2250 / 88.5
2250 / 88.5
NOMINAL CAPACITY
294 / 1.18
SEQUENTIAL CONTROLLER
EVAPORATOR
DUCTED
CONDENSATE DRAIN SIZE
CONDENSER
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
HEIGHT
WIDTH
REFRIGERANT CHARGE
DEPTH
UNIT WEIGHT
A4RT250A
2800 / 110.0
1900 / 75
2900 / 114
UNIT DIMENSION
SOUND PRESSURE LEVEL
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
A4RT300A
380 ~ 415 / 3 / 50
CONTROL
MODEL
REFRIGERANT TYPE / CONTROL
EER
R407C / TXV
74
1735 / 68.0
AIR FLOW
POWER SOURCE
9439 / 20000
25.4 / 1
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
70
Page 72
General Data - Cooling Only (R407C)
Btu/h 331000 415000
W 97010 121620
W 41870 48800
A 74.2 83.7
V/Ph/Hz
W/W 2.32 2.49
AIR DISCHARGE
OPERATION
AIR FLOW l/s / cfm 5191 / 11000 5899 / 12500
EXTERNAL STATIC PRESSURE (H/M/L) Pa/in.wg.
mm/in
l/s / cfm
dBA
mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 1510 / 3329 1600 / 3527 kg/lb 14.5 / 32.0 & 18.0 / 39.72 x 18.0 / 2 x 39.7
MODEL
70
AIR FLOW
POWER SOURCE
9439 / 20000
25.4 / 1
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
WIDTH
REFRIGERANT CHARGE
DEPTH
UNIT WEIGHT
REFRIGERANT TYPE / CONTROL
EER
A4RT360A
3180 / 125.0
CONTROL
CONDENSER
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
2150 / 84.5
3250 / 128.0
A4RT420A
380 ~ 415 / 3 / 50
1974 / 78.0 2252 / 89.0
2300 / 90.5
R407C / TXV
HEIGHT
NOMINAL CAPACITY
294 / 1.18
SEQUENTIAL CONTROLLER
EVAPORATOR
DUCTED
CONDENSATE DRAIN SIZE
UNIT DIMENSION
SOUND PRESSURE LEVEL
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STA NDARD: ISO 13253
71
Page 73
General Data - Heat pump (R407C)
General Data - Heat pump (R407C)
Btu/h 56000 72000
W 16710 21100
Btu/h 69000 77000
W 20220 22570 W 6650 8410 W 6580 7540
A 13.2 16.0 A 12.9 15.4
V/Ph/Hz
W/W 2.47 2.40 W/W 3.07 2.85
AIR DISCHARGE OPERATION
AIR FLOW l/s / cfm 850 / 1800 1334 / 2826 EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm 2124 / 4500 2667 / 5650
dBA 63 65
mm/in mm/in 1100 / 43.3
1300 / 51.2
mm/in mm/in mm/in
1250 / 49.2
1450 / 57.1
mm/in
kg/lb
320 / 705
385 / 849
kg/lb
4.3 / 9.5
5.2 / 11.5
1680 / 66.1
25.4 / 1
1000 / 39.4
1530 / 60.2 1090 / 42.9
A4RT60AR A4RT80AR
380 ~ 415 / 3 / 50
98 / 0.39
DUCTED
SLM CONTROLLER
R407C / TXV
NOMINAL RUNNING CURRENT (HEATING) POWER SOURCE REFRIGERANT TYPE / CONTROL EER COP
MODEL
CONTROL
EVAPORATOR*
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER (COOLING) NOMINAL TOTAL INPUT POWER (HEATING) NOMINAL RUNNING CURRENT (COOLING)
CONDENSATE DRAIN SIZE
UNIT DIMENSION
SOUND PRESSURE LEVEL
CONDENSER*
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
HEIGHT
WIDTH
REFRIGERANT CHARGE
AIR FLOW
DEPTH
UNIT WEIGHT
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) * DESIGNATION BASED ON COOLING CYCLE.
6) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
Btu/h 88000 100000
W 25790 29310
Btu/h 102000 122000
W 29890 35760 W 10820 12810 W 9810 11260
A 20.6 23.2 A 19.3 21.2
V/Ph/Hz
W/W 2.26 2.29 W/W 2.92 3.17
AIR DISCHARGE OPERATION
AIR FLOW l/s / cfm 1667 / 3532 1699 / 3600 EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm 2667 / 5650 4719 / 10000
dBA 66 68
mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 415 / 915 440 / 970 kg/lb 6.0 / 13.26.0 / 13.2
1680 / 66.1
25.4 / 1
UNIT WEIGHT
CONDENSATE DRAIN SIZE
UNIT DIMENSION
SOUND PRESSURE LEVEL
1450 / 57.1
1000 / 39.4
1530 / 60.2 1090 / 42.9
CONDENSER*
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
HEIGHT
WIDTH
REFRIGERANT CHARGE
AIR FLOW
DEPTH
MODEL
CONTROL
EVAPORATOR*
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER (COOLING) NOMINAL TOTAL INPUT POWER (HEATING) NOMINAL RUNNING CURRENT (COOLING) NOMINAL RUNNING CURRENT (HEATING) POWER SOURCE REFRIGERANT TYPE / CONTROL EER COP
1300 / 51.2
A4RT100AR A4RT120AR
380 ~ 415 / 3 / 50
98 / 0.39
DUCTED
SLM CONTROLLER
R407C / TXV
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) * DESIGNATION BASED ON COOLING CYCLE.
6) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
72
Page 74
General Data - Heat pump (R407C)
General Data - Heat pump (R407C)
Btu/h 149000 190000
W
43670
55680
Btu/h
160000
230000
W 46890 67410 W 16570 21160 W 15710 20300 A 32.2 39.9 A 31.2 38.4
V/Ph/Hz
W/W 2.75 2.63 W/W 3.12 3.32
AIR DISCHARGE OPERATION
AIR FLOW l/s / cfm 2667 / 5651 3167 / 6710 EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in l/s / cfm
dBA mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 700 / 1543 800 / 1764 kg/lb 2 x 5.0 / 2 x 11.02 x 5.8 / 2 x 12.8
1938 / 76.3
25.4 / 1
1200 / 47.2
1800 / 70.9 1320 / 52.0
1990 / 78.4
2100 / 82.7
5333 / 11300
70
A4RT150AR A4RT200AR
380 ~ 415 / 3 / 50
196 / 0.79
DUCTED
SEQUENTIAL CONTROLLER
R407C / TXV
NOMINAL RUNNING CURRENT (HEATING) POWER SOURCE REFRIGERANT TYPE / CONTROL EER COP
MODEL
CONTROL
EVAPORATOR*
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER (COOLING) NOMINAL TOTAL INPUT POWER (HEATING) NOMINAL RUNNING CURRENT (COOLING)
CONDENSATE DRAIN SIZE
UNIT DIMENSION
SOUND PRESSURE LEVEL
CONDENSER*
PACKING DIMENSION
HEIGHT
WIDTH
DEPTH
HEIGHT
WIDTH
REFRIGERANT CHARGE
AIR FLOW
DEPTH
UNIT WEIGHT
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STA NDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) * DESIGNATION BASED ON COOLING CYCLE.
6) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
Btu/h 230000 283000
W 67410 82940
Btu/h 255000
315000
W
74730
92320
W 29200
38160
W 26220 34780 A 52.1 65.5 A 48.6 61.9
V/Ph/Hz
W/W 2.30 2.07
W/W 2.73 2.55
AIR DISCHARGE OPERATION
AIR FLOWl/s / cfm 3776 / 8000 4531 / 9600 EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm
dBA mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 1200 / 2646 1350 / 2976 kg/lb 2 x 9.4 / 2 x 20.72 x 9.6 / 2 x 21.2
REFRIGERANT CHARGE
AIR FLOW
DEPTH
UNIT WEIGHT
CONDENSATE DRAIN SIZE
UNIT DIMENSION
SOUND PRESSURE LEVEL
CONDENSER*
PACKING DIMENSION
HEIGHT
WIDTH DEPTH
HEIGHT
WIDTH
MODEL
CONTROL
EVAPORATOR*
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER (COOLING) NOMINAL TOTAL INPUT POWER (HEATING) NOMINAL RUNNING CURRENT (COOLING) NOMINAL RUNNING CURRENT (HEATING) POWER SOURCE REFRIGERANT TYPE / CONTROL EER COP
A4RT250AR A4RT300AR
380 ~ 415 / 3 / 50
294 / 1.18
DUCTED
SEQUENTIAL CONTROLLER
R407C / TXV
2900 / 114
25.4 / 1
1735 / 68.0
2800 / 110.0
1900 / 75
2250 / 88.5
2250 / 88.5
9439 / 20000
74
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) * DESIGNATION BASED ON COOLING CYCLE.
6) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
73
Page 75
General Data - Heat pump (R407C)
Btu/h 345000 374000
W 101110
Btu/h 349000 431000
W 102290
126310
W 43170 48200
W 41670 46800
A 74.2 82.9 A 72.0 81.1
V/Ph/Hz
W/W 2.34 2.27 W/W 2.45 2.70
AIR DISCHARGE OPERATION
AIR FLOW l/s / cfm 5191 / 11000 5899 / 12500 EXTERNAL STATIC PRESSURE Pa/in.wg.
mm/in
l/s / cfm
dBA
mm/in mm/in mm/in mm/in mm/in mm/in
kg/lb 1510 / 3329 1600 / 3527 kg/lb
13.5/ 29.7 & 16 / 35.3
2 x 16 / 2 x 35.3
9439 / 20000
70
EER COP
A4RT360AR A4RT420AR
380 ~ 415 / 3 / 50
294 / 1.18
DUCTED
SEQUENTIAL CONTROLLER
R407C / TXV
NOMINAL RUNNING CURRENT (COOLING) NOMINAL RUNNING CURRENT (HEATING) POWER SOURCE REFRIGERANT TYPE / CONTROL
DEPTH
MODEL
CONTROL
EVAPORATOR*
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER (COOLING) NOMINAL TOTAL INPUT POWER (HEATING)
2252 / 89.0
CONDENSER*
PACKING DIMENSION
HEIGHT
WIDTH
DEPTH
HEIGHT
WIDTH
REFRIGERANT CHARGE
AIR FLOW
UNIT WEIGHT
3250 / 128.0
2300 / 90.5
CONDENSATE DRAIN SIZE
UNIT DIMENSION
SOUND PRESSURE LEVEL
25.4 / 1
1974 / 78.0
3180 / 125.0
2150 / 84.5
109610
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEAT ING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
5) * DESIGNATION BASED ON COOLING CYCLE.
6) EFFECTIVE POWER INPUT IS USED IN THE RATED EER/COP CALCULATION, ACCORDING TO ISO STANDARD: ISO 13253
74
Page 76
Components Data (R22)
mm/in
mm/in
mm/in
cm
3
/fl.oz.
mm/in
mm/in
mm/in
m
2
/ft
2
mm/in
mm/in
mm/in
m2/ft
2
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
THICKNESS
ROW
FIN PER INCH
MATERIAL
MATERIAL
0.28 / 0.011
SONTEX 200LT
1
FACE AREA
MATERIAL
THICKNESS
DIAMETER
THICKNESS
MATERIAL
COMPRESSOR
TYPE
OIL TYPE
QUANTITY
OIL AMOUNT
CONDENSER FAN
MOTOR
CONDENSER FAN MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
INDEX OF PROTECTION (IP)
QUANTITY
DIAMETER
EVAPORATOR FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
TYPE
QUANTITY
DIAMETER
MODEL
TYPE
EVAPORATOR FAN
LENGTH
CONDENSER COIL
FIN
FIN
TUBE
TUBE
EVAPORATOR COIL
CASING
AIR QUALITYFILTER
TYPE
QUANTITY
INSULATION / THICKNESS
EXTERNAL FINISHING
COLOUR
SIZE
MATERIAL
ROW
FIN PER INCH
FACE AREA
0.11 / 0.004
9.52 / 3/8
0.28 / 0.011
ALUMINIUM
3
DIAMETER
THICKNESS
CENTRIFUGAL
1
1
PLASTIC
1
IP22
254 / 10
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
PROPELLER
N/A
N/A
N/A
BELT DRIVE
1
ALUMINIUM
INDUCTION MOTOR
DIRECT DRIVE
SCROLL
9.52 / 3/8
609.6 / 24.0
IP54
LIGHT GREY
PE / 10mm
0.11 / 0.004
N/A
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
2
0.44 / 4.75
S.I.G.C.
18
N/A
ART55A
1770 / 62.3
S.I.G.C.
0.44 / 4.75
14
METAL
203 / 8
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
75
Page 77
Components Data (R22)
PLASTIC GALVANISED STEEL
mm/in
mm/in 254 / 10 254 / 10 & 203.2 / 8.0
mm/in 609.6 / 24.0 660.4 / 26.0
IP54
IP44
cm3/fl.oz.
1770 / 62.3 2510 / 88.3
S.I.G.C.
SEAMLESS COPPER
mm/in
mm/in
mm/in
m2/ft
2
0.53 / 5.700.65 / 6.96
16 15
S.I.G.C.
SEAMLESS COPPER
mm/in
mm/in
mm/in
m2/ft
2
16
pc
LENGTH mm/in 820 / 32.3 1020 / 40.2
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
16
FACE AREA
DIAMETER
THICKNESS
THICKNESS
ROW
FIN PER INCH
MATERIAL
MATERIAL
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
PROPELLER
ALUMINIUM
INDUCTION MOTOR
DIRECT DRIVE
SCROLL
9.52 / 3/8
0.33 / 0.013
SONTEX 200LT
1
MATERIAL
THICKNESS
COMPRESSOR
TYPE
OIL TYPE
QUANTITY
OIL AMOUNT
DIAMETER
THICKNESS
MATERIAL
CONDENSER FAN MOTOR
CONDENSER FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
INDEX OF PROTECTION (IP)
QUANTITY
DIAMETER
EVAPORATOR FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
TYPE
QUANTITY
DIAMETER
MODEL
TYPE
EVAPORATOR FAN
LENGTH
CONDENSER COIL
FIN
FIN
TUBE
TUBE
EVAPORATOR COIL
CASING
AIR QUALITY FILTER
TYPE
QUANTITY
INSULATION / THICKNESS
EXTERNAL FINISHING
COLOUR
SIZE
MATERIAL
ROW
FIN PER INCH
FACE AREA
ART60A
0.11 / 0.004
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
3
254 / 10
1 / 0.04
ART80A
BELT DRIVE
CENTRIFUGAL
2
1
GALVANISED STEEL
1
IP22
1
LIGHT GREY
PE / 10mm
0.11 / 0.004
WASHABLE SARANET
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
2
1.41 / 15.17
1
615 / 24.2
76
Page 78
Components Data (R22)
mm/in
mm/in
mm/in 660.4 / 26.0 762 / 30
IP44 N/A
cm3/fl.oz.
SEAMLESS COPPER S.I.G.C.
mm/in
mm/in
mm/in
m2/ft
2
0.65 / 6.960.65 / 6.99
15 14
SEAMLESS COPPER S.I.G.C.
mm/in
mm/in
mm/in
m2/ft
2
16 14
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
PE / 10mm
SONTEX 200LT
3250 / 114.4
QUANTITY 1
OIL AMOUNT
0.11 / 0.004
WASHABLE SARANET
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
254 / 10
254 / 10 & 203.2 / 8.0
3
ALUMINIUM
ALUMINIUM
0.11 / 0.004
9.52 / 3/8
0.33 / 0.013
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
PROPELLER
1020 / 40.2
1
1.42 / 15.28
615 / 24.2
1 / 0.04
THREE PHASE INDUCTION MOTOR
DIRECT DRIVE
1
1
IP22
GALVANISED STEEL
1
4
SCROLL
ART100A ART120A
BELT DRIVE
CENTRIFUGAL
GALVANISED STEEL
2
FIN PER INCH
DIAMETER
THICKNESS
THICKNESS
FACE AREA
CASING
AIR QUALITY FILTER
TYPE
QUANTITY
INSULATION / THICKNESS
SIZE
MATERIAL
EXTERNAL FINISHING
COLOUR
CONDENSER COIL
FIN
FIN
TUBE
TUBE
MODEL
TYPE
EVAPORATOR FAN
DIAMETER
LENGTH
EVAPORATOR FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
TYPE
QUANTITY
CONDENSER FAN MOTOR
CONDENSER FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
DIAMETER
INDEX OF PROTECTION (IP)
QUANTITY
COMPRESSOR
TYPE
OIL TYPE
EVAPORATOR COIL
DIAMETER
THICKNESS
THICKNESS
MATERIAL
LIGHT GREY
9.52 / 3/8
0.33 / 0.013
MATERIAL
ROW
FACE AREA
FIN PER INCH
MATERIAL
MATERIAL
ROW
77
Page 79
Components Data (R22)
mm/in
mm/in
mm/in
cm3/fl.oz.
2510 / 88.3 3250 / 114.4
mm/in
mm/in
mm/in
m2/ft
2
34
mm/in
mm/in
mm/in
m2/ft
2
23
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
PE / 10mm
1 / 0.04
SIZE
MATERIAL
EXTERNAL FINISHING
THICKNESS
THICKNESS
FACE AREA
DIAMETER
MATERIAL
ROW
FIN PER INCH
MATERIAL
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
ALUMINIUM
2 x 0.57 / 2 x 6.12
0.11 / 0.004
9.52 / 3/8
0.33 / 0.013
15
S.I.G.C.
384.5 / 15.1
374.0 / 14.7
660.4 / 26.0
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
PROPELLER
1
2
IP22
GALVANISED STEEL
SONTEX 200LT
S.I.G.C.
THREE PHASE INDUCTION MOTOR
DIRECT DRIVE
IP44
2
SCROLL
2
MATERIAL
DIAMETER
CONDENSER FAN MOTOR
INDEX OF PROTECTION (IP)
QUANTITY
COMPRESSOR
TYPE
OIL TYPE
QUANTITY
OIL AMOUNT
CONDENSER FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
DIAMETER
TYPE
QUANTITY
EVAPORATOR FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
DIAMETER
LENGTH
MODEL
TYPE
EVAPORATOR FAN
CONDENSER COIL
FIN
FIN
TUBE
TUBE
EVAPORATOR COIL
CASING
AIR QUALITY FILTER
TYPE
QUANTITY
INSULATION / THICKNESS
COLOUR
MATERIAL
ROW
FIN PER INCH
THICKNESS
THICKNESS
FACE AREA
ART150A ART200A
BELT DRIVE
CENTRIFUGAL
PLASTIC
2
0.11 / 0.004
WASHABLE SARANET
ELECTRO GALVANISED MILD STEEL
LIGHT GREY
EPOXY POLYESTER POWDER
2 X 1.25 / 2 x 13.44
2
840 / 33.1
16
667 / 26.3
78
Page 80
Components Data (R22)
mm/in
mm/in 480 / 18.9 481 / 18.9
mm/in
cm3/fl.oz.
3250 / 114.4 4140 / 145.7
mm/in
mm/in
mm/in
m2/ft
2
SEAMLESS COPPER S.I.G.C.
mm/in
mm/in
mm/in
m2/ft
2
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
735 / 28.9
1 / 0.04
MATERIAL
EXTERNAL FINISHING
TYPE
QUANTITY
SIZE
ROW
FIN PER INCH
FACE AREA
DIAMETER
THICKNESS
THICKNESS
MATERIAL
MATERIAL
OIL AMOUNT
DIAMETER
THICKNESS
THICKNESS
TUBE
457.2 / 18
2 x 3.01 / 2 x 32.44
ALUMINIUM
2 x 0.91 / 2 x 9.84
14
GALVANISED STEEL
IP22
9.52 / 3/8
0.33 / 0.013
2
0.33 / 0.013
PE / 10mm
0.11 / 0.004
WASHABLE SARANET
ELECTRO GALVANISED MILD STEEL
LIGHT GREY
EPOXY POLYESTER POWDER
2
2
1370 / 53.9
14
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
PROPELLER
THREE PHASE INDUCTION MOTOR
DIRECT DRIVE
1
2
812.8 / 32.0
4
0.11 / 0.004
ART250A ART300A
BELT DRIVE
CENTRIFUGAL
GALVANISED STEEL
1
CASING
CONDENSER COIL
FIN
FIN
TUBE
COLOUR
INSULATION / THICKNESS
FACE AREA
AIR QUALITY FILTER
TYPE
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
QUANTITY
QUANTITY
MODEL
TYPE
EVAPORATOR FAN
DIAMETER
LENGTH
EVAPORATOR FAN MOTOR
QUANTITY
INDEX OF PROTECTION (IP)
CONDENSER FAN
MATERIAL
DRIVE
TYPE
QUANTITY
DIAMETER
CONDENSER FAN MOTOR
TYPE
ROW
FIN PER INCH
COMPRESSOR
TYPE
OIL TYPE
EVAPORATOR COIL
MATERIAL
MATERIAL
IP55
SCROLL
9.52 / 3/8
ALUMINIUM
SEAMLESS COPPER
2
SONTEX 200LT
79
Page 81
Components Data (R22)
mm/in
mm/in
mm/in
320 SZ
cm 3 /fl.oz.
8000 / 281.6
S.I.G.C.
160P & 320SZ
6600 / 232.3 & 8000 / 281.6
S.I.G.C.
mm/in
mm/in
mm/in
m 2 /ft
2
S.I.G.C. S.I.G.C.
mm/in
mm/in
mm/in
m 2 /ft
2
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
SCROLL
9.52 / 3/8
ALUMINIUM
2
CONDENSER FAN MOTOR
TYPE
ROW
FIN PER INCH
COMPRESSOR
TYPE
OIL TYPE
EVAPORATOR COIL
MATERIAL
MATERIAL
INDEX OF PROTECTION (IP)
CONDENSER FAN
MATERIAL
DRIVE
TYPE
QUANTITY
DIAMETER
INDEX OF PROTECTION (IP)
QUANTITY
QUANTITY
MODEL
TYPE
EVAPORATOR FAN
DIAMETER
LENGTH
EVAPORATOR FAN MOTOR
QUANTITY
TYPE
QUANTITY
MATERIAL
DRIVE
CASING
CONDENSER COIL
FIN
FIN
TUBE
COLOUR
INSULATION / THICKNESS
FACE AREA
AIR QUALITY FILTER
ART360A ART420A
BELT DRIVE
560 / 22
457 / 18
CENTRIFUGAL
GALVANISED STEEL
1
13
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
PROPELLER
GALVANISED STEEL
THREE PHASE INDUCTION MOTOR
DIRECT DRIVE
1
IP22
IP55
2
812.8 / 32.0
3 & 4
0.11 / 0.004
3.02 / 32.5
0.33 / 0.013
PE / 10mm
0.11 / 0.004
3.50 / 37.7
WASHABLE SARANET
ELECTRO GALVANISED MILD STEEL
LIGHT GREY
EPOXY POLYESTER POWDER
860 / 33.86
4 / 0.16
505 / 19.88 & 600 / 23.62
3
14 & 13
2 & 3
2 & 4
ALUMINIUM
14 & 13
4
13
9.52 / 3/8
0.33 / 0.013
2
OIL AMOUNT
DIAMETER
THICKNESS
THICKNESS
TUBE
FACE AREA
DIAMETER
THICKNESS
THICKNESS
MATERIAL
MATERIAL
TYPE
QUANTITY
SIZE
ROW
FIN PER INCH
MATERIAL
EXTERNAL FINISHING
80
Page 82
Components Data (R22)
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
3) * DESIGNATION BASED ON COOLING CYCLE.
mm/in
mm/in
mm/in
cm
3
/fl.oz.
mm/in
mm/in
mm/in
m
2
/ft
2
mm/in
mm/in
mm/in
m
2
/ft
2
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
THICKNESS
ROW
FIN PER INCH
MATERIAL
MATERIAL
0.28 / 0.011
SONTEX 200LT
1
FACE AREA
MATERIAL
THICKNESS
DIAMETER
THICKNESS
MATERIAL
COMPRESSOR
TYPE
OIL TYPE
QUANTITY
OIL AMOUNT
CONDENSER
*
FAN
MOTOR
CONDENSER
*
FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
INDEX OF PROTECTION (IP)
QUANTITY
DIAMETER
EVAPORATOR* FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
TYPE
QUANTITY
DIAMETER
MODEL
TYPE
EVAPORATOR
*
FAN
LENGTH
CONDENSER* COIL
FIN
FIN
TUBE
TUBE
EVAPORATOR* COIL
CASING
AIR QUALITYFILTER
TYPE
QUANTITY
INSULATION / THICKNESS
EXTERNAL FINISHING
COLOUR
SIZE
MATERIAL
ROW
FIN PER INCH
FACE AREA
0.11 / 0.004
9.52 / 3/8
0.28 / 0.011
ALUMINIUM
3
DIAMETER
THICKNESS
CENTRIFUGAL
1
1
PLASTIC
1
IP22
254 / 10
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
PROPELLER
N/A
N/A
N/A
BELT DRIVE
1
ALUMINIUM
INDUCTION MOTOR
DIRECT DRIVE
SCROLL
9.52 / 3/8
609.6 / 24.0
IP54
LIGHT GREY
PE / 10mm
0.11 / 0.004
N/A
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
3
0.44 / 4.75
S.I.G.C.
14
N/A
ART55AR
1770 / 62.3
S.I.G.C.
0.44 / 4.75
14
METAL
203 / 8
81
Page 83
Components Data (R22)
PLASTIC GALVANISED STEEL
mm/in 254 / 10286.0 / 11.3
mm/in 254 / 10274.0 / 10.8 & 184.0 / 7.2
mm/in 609.6 / 24.0660.4 / 26.0
IP54 IP44
SCROLL RECIPROCATING
SONTEX 200LTDIAMOND MS 32(N-1)
cm3/fl.oz.
1770 / 62.3 3000 / 106.0
mm/in
mm/in
mm/in
m2/ft
2
0.53 / 5.700.65 / 6.96
16 15
mm/in
mm/in
mm/in
m2/ft
2
16 13
pc
LENGTH mm/in 820 / 32.3 1020 / 40.2
WIDTH mm/in
THICKNESS mm/in
LIGHT GREY
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
3) * DESIGNATION BASED ON COOLING CYCLE.
THICKNESS
FACE AREA
MATERIAL
MATERIAL
FILTER
QUANTITY
SIZE
TYPE
MATERIAL
ROW
FIN PER INCH
DIAMETER
THICKNESS
THICKNESS
FACE AREA
COMPRESSOR
TYPE
OIL TYPE
INDEX OF PROTECTION (IP)
QUANTITY
CONDENSER* FAN MOTOR
OIL AMOUNT
QUANTITY
CONDENSER* FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
DIAMETER
TYPE
QUANTITY
EVAPORATOR* FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
DIAMETER
LENGTH
MODEL
TYPE
EVAPORATOR* FAN
FIN PER INCH
DIAMETER
THICKNESS
EVAPORATOR* COIL
CONDENSER* COIL
FIN
FIN
TUBE
TUBE
MATERIAL
PE / 10mm
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
CASING
MATERIAL
EXTERNAL FINISHING
COLOUR
INSULATION / THICKNESS
AIR QUALITY
615 / 24.2
1 / 0.04
1
WASHABLE SARANET
2
1
ALUMINIUM
0.11 / 0.004
ROW
GALVANISED STEEL
ART60AR ART80AR
CENTRIFUGAL
2
BELT DRIVE
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
1
PROPELLER
1
DIRECT DRIVE
INDUCTION MOTOR
ALUMINIUM
0.11 / 0.004
IP22
1.41 / 15.17
1
0.33 / 0.013
S.I.G.C.
3
S.I.G.C.
9.52 / 3/8
9.52 / 3/8
0.33 / 0.013
82
Page 84
Components Data (R22)
mm/in 286.0 / 11.3 254 / 10
mm/in 274.0 / 10.8 & 184.0 / 7.2 254 / 10 & 203.2 / 8.0
mm/in 660.4 / 26.0 762 / 30
RECIPROCATING SCROLL
SUNISO 3GS SONTEX 200LT
cm3/fl.oz.
4500 / 158.4 3250 / 114.4
mm/in
mm/in
mm/in
m2/ft
2
0.65 / 6.96 0.65 / 6.99
15 14
mm/in
mm/in
mm/in
m2/ft
2
13 14
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
LIGHT GREY
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
3) * DESIGNATION BASED ON COOLING CYCLE.
615 / 24.2
1 / 0.04
PE / 10mm
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
MATERIAL
EXTERNAL FINISHING
COLOUR
INSULATION / THICKNESS
THICKNESS
TYPE
QUANTITY
SIZE
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
WASHABLE SARANET
3
1.42 / 15.28
ART100AR ART120AR
CENTRIFUGAL
2
CASING
FILTERAIR QUALITY
MATERIAL
MATERIAL
ROW
FIN PER INCH
FACE AREA
CONDENSER* COIL
FIN
TUBE
TUBE
TYPE
QUANTITY
FIN PER INCH
FACE AREA
DIAMETER
THICKNESS
MODEL
TYPE
EVAPORATOR* FAN
DIAMETER
LENGTH
EVAPORATOR* FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
CONDENSER* FAN MOTOR
CONDENSER* FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
DIAMETER
COMPRESSOR
TYPE
OIL TYPE
EVAPORATOR* COIL
QUANTITY
OIL AMOUNT
DIAMETER
THICKNESS
THICKNESS
FIN
GALVANISED STEEL
MATERIAL
MATERIAL
ROW
INDEX OF PROTECTION (IP)
QUANTITY
BELT DRIVE
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
1
IP22
1
1020 / 40.2
PROPELLER
1
DIRECT DRIVE
THREE PHASE INDUCTION MOTOR
1
S.I.G.C.
4
S.I.G.C.
IP22
GALVANISED STEEL
1
9.52 / 3/8
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
83
Page 85
Components Data (R22)
mm/in
mm/in
mm/in
DIAMOND MS 32(N-1) SUNISO 3GS
cm3/fl.oz.
3000 / 106.0 4500 / 158.4
mm/in
mm/in
mm/in
m2/ft
2
34
mm/in
mm/in
mm/in
m2/ft
2
23
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
3) * DESIGNATION BASED ON COOLING CYCLE.
CASING
COLOUR
INSULATION / THICKNESS
FILTER
TYPE
QUANTITY
EXTERNAL FINISHING
MATERIAL
FACE AREA
667 / 26.3
1 / 0.04
AIR QUALITY
CONDENSER* COIL
FIN
WASHABLE SARANET
SIZE
FIN PER INCH
2 x 1.25 / 2 x 13.44
THICKNESS
THICKNESS
FIN PER INCH
MATERIAL
MATERIAL
DIAMETER
THICKNESS
FACE AREA
DIAMETER
COMPRESSOR
TYPE
OIL TYPE
EVAPORATOR* COIL
QUANTITY
MATERIAL
MATERIAL
ROW
THICKNESS
OIL AMOUNT
CONDENSER* FAN MOTOR
CONDENSER* FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
INDEX OF PROTECTION (IP)
QUANTITY
DIAMETER
EVAPORATOR* FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
DIAMETER
MODEL
TYPE
EVAPORATOR* FAN
LENGTH
FIN
TUBE
TUBE
PE / 10mm
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
LIGHT GREY
2
840 / 33.1
13
PLASTIC
BELT DRIVE
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
ROW
TYPE
QUANTITY
PROPELLER
2
DIRECT DRIVE
THREE PHASE INDUCTION MOTOR
ART150AR ART200AR
CENTRIFUGAL
2
IP44
9.52 / 3/8
660.4 / 26.0
IP22
GALVANISED STEEL
2
S.I.G.C.
2
1
384.5 / 15.1
374.0 / 14.7
S.I.G.C.
RECIPROCATING
2 x 0.57 / 6.12
15
0.11 / 0.004
0.33 / 0.013
ALUMINIUM
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
9.52 / 3/8
84
Page 86
Components Data (R22)
mm/in
mm/in 480 / 18.9 481 / 18.9
mm/in
cm3/fl.oz.
3250 / 114.4 4140 / 145.7
SEAMLESS COPPER S.I.G.C.
mm/in
mm/in
mm/in
m2/ft
2
SEAMLESS COPPER S.I.G.C.
mm/in
mm/in
mm/in
m2/ft
2
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
3) * DESIGNATION BASED ON COOLING CYCLE.
AIR QUALITY
735 / 28.9
1 / 0.04
MATERIAL
WASHABLE SARANET
FILTER
TYPE
QUANTITY
SIZE
2
14
DIAMETER
LENGTH
DIAMETER
OIL AMOUNT
DIAMETER
THICKNESS
THICKNESS
14
ART250AR ART300AR
CENTRIFUGAL
1
PE / 10mm
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
CASING
LIGHT GREY
EXTERNAL FINISHING
COLOUR
INSULATION / THICKNESS
CONDENSER* COIL
FIN
FIN
TUBE
TUBE
MODEL
TYPE
EVAPORATOR* FAN
TYPE
QUANTITY
EVAPORATOR* FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
CONDENSER* FAN MOTOR
CONDENSER* FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
COMPRESSOR
TYPE
OIL TYPE
EVAPORATOR* COIL
QUANTITY
FACE AREA
FIN PER INCH
GALVANISED STEEL
MATERIAL
MATERIAL
ROW
INDEX OF PROTECTION (IP)
QUANTITY
BELT DRIVE
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
1
457.2 / 18
FIN PER INCH
0.33 / 0.013
IP54
GALVANISED STEEL
IP54
PROPELLER
2
DIRECT DRIVE
THREE PHASE INDUCTION MOTOR
812.8 / 32.0
MATERIAL
MATERIAL
ROW
DIAMETER
THICKNESS
THICKNESS
FACE AREA 2 x 3.01 / 2 x 32.44
2
1370 / 53.9
2
SONTEX 200LT
ALUMINIUM
0.11 / 0.004
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
2
SCROLL
4
9.52 / 3/8
9.52 / 3/8
2 x 0.91 / 9.84
85
Page 87
Components Data (R22)
mm/in
mm/in
mm/in
320 SZ
cm 3 /fl.oz.
8000 / 281.6
S.I.G.C.
160P & 320SZ
6600 / 232.3 & 8000 / 281.6
S.I.G.C.
mm/in
mm/in
mm/in
m 2 /ft
2
S.I.G.C.
mm/in
mm/in
mm/in
m 2 /ft
2
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
3) * DESIGNATION BASED ON COOLING CYCLE.
2
SCROLL
4
9.52 / 3/8
9.52 / 3/8
2
2 & 4
ALUMINIUM
0.11 / 0.004
3.50 /37.7
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
3
MATERIAL
MATERIAL
ROW
DIAMETER
THICKNESS
THICKNESS
FACE AREA
FIN PER INCH
0.33 / 0.013
PROPELLER
2
GALVANISED STEEL
DIRECT DRIVE
THREE PHASE INDUCTION MOTOR
812.8 / 32.0
GALVANISED STEEL
3.02 / 32.5
MATERIAL
MATERIAL
ROW
INDEX OF PROTECTION (IP)
QUANTITY
BELT DRIVE
560 / 22
457 / 18
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
1
IP44
IP54
COMPRESSOR
TYPE
OIL TYPE
EVAPORATOR* COIL
QUANTITY
FACE AREA
FIN PER INCH
CONDENSER* FAN MOTOR
CONDENSER* FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
QUANTITY
EVAPORATOR* FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
MODEL
TYPE
EVAPORATOR* FAN
CONDENSER* COIL
FIN
FIN
TUBE
TUBE
PE / 10mm
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
CASING
LIGHT GREY
860 / 33.86
505 / 19.88 & 600 / 23.62
4 / 0.16
EXTERNAL FINISHING
COLOUR
INSULATION / THICKNESS
ART360AR ART420AR
CENTRIFUGAL
1
13
DIAMETER
LENGTH
DIAMETER
OIL AMOUNT
DIAMETER
THICKNESS
THICKNESS
13
S.I.G.C.
3 & 4
14 & 13
TYPE
AIR QUALITY
MATERIAL
WASHABLE SARANET
FILTER
TYPE
QUANTITY
SIZE
86
Page 88
Components Data (R407C)
PLASTIC GALVANISED STEEL
mm/in
mm/in 254 / 10 254 / 10 & 203.2 / 8.0
mm/in 609.6 / 24.0 660.4 / 26.0
IP54 IP44
cm3/fl.oz.
1770 / 62.32510 / 88.3
S.I.G.C.
SEAMLESS COPPER
mm/in
mm/in
mm/in
m2/ft
2
0.53 / 5.700.65 / 6.96
16 15
mm/in
mm/in
mm/in
m2/ft
2
pc
LENGTH mm/in 820 / 32.31020 / 40.2
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
LIGHT GREY
PE / 10mm
MATERIAL
MATERIAL
ROW
FIN PER INCH
DIAMETER
THICKNESS
THICKNESS
FACE AREA
MATERIAL
COMPRESSOR
TYPE
OIL TYPE
EVAPORATOR COIL
CONDENSER COIL
FIN
FIN
TUBE
TUBE
INDEX OF PROTECTION (IP)
OIL AMOUNT
CONDENSER FAN MOTOR
QUANTITY
QUANTITY
CONDENSER FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
DIAMETER
EVAPORATOR FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
TYPE
DIAMETER
LENGTH
QUANTITY
MODEL
TYPE
EVAPORATOR FAN
CASING
AIR QUALITY FILTER
TYPE
QUANTITY
INSULATION / THICKNESS
SIZE
MATERIAL
EXTERNAL FINISHING
COLOUR
MATERIAL
ROW
FIN PER INCH
DIAMETER
THICKNESS
THICKNESS
FACE AREA
POE
A4RT60A A4RT80A
BELT DRIVE
CENTRIFUGAL
2
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
PROPELLER
INDUCTION MOTOR
DIRECT DRIVE
3
S.I.G.C.
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
WASHABLE SARANET
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
2
16
615 / 24.2
1 / 0.04
1
1
1
SCROLL
IP22
1.41 / 15.17
1
254 / 10
GALVANISED STEEL
1
0.11 / 0.004
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
87
Page 89
Components Data (R407C)
mm/in
mm/in
mm/in 660.4 / 26.0 762 / 30
IP22 N/A
cm3/fl.oz.
SEAMLESS COPPER S.I.G.C.
mm/in
mm/in
mm/in
m2/ft
2
0.65 / 6.96 0.65 / 6.99
15 14
mm/in
mm/in
mm/in
m2/ft
2
16 14
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
LIGHT GREY
PE / 10mm
DIAMETER
THICKNESS
THICKNESS
FACE AREA
MATERIAL
0.11 / 0.004
WASHABLE SARANET
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
254 / 10 & 203.2 / 8.0
254 / 10
3
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
1.42 / 15.28
1
1020 / 40.2
S.I.G.C.
615 / 24.2
1 / 0.04
A4RT120A
BELT DRIVE
CENTRIFUGAL
GALVANISED STEEL
2
3250 / 114.4
1
IP22
GALVANISED STEEL
ROW
FIN PER INCH
A4RT100A
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
PROPELLER
THREE PHASE INDUCTION MOTOR
DIRECT DRIVE
1
1
CASING
AIR QUALITY FILTER
TYPE
QUANTITY
INSULATION / THICKNESS
SIZE
MATERIAL
EXTERNAL FINISHING
COLOUR
FIN PER INCH
DIAMETER
THICKNESS
CONDENSER COIL
FIN
FIN
EVAPORATOR COIL
TUBE
MODEL
TYPE
EVAPORATOR FAN
DIAMETER
LENGTH
QUANTITY
MATERIAL
FACE AREA
DRIVE
INDEX OF PROTECTION (IP)
TYPE
QUANTITY
DIAMETER
QUANTITY
EVAPORATOR FAN MOTOR
CONDENSER FAN
MATERIAL
DRIVE
TYPE
QUANTITY
CONDENSER FAN MOTOR
TYPE
MATERIAL
SCROLL
COMPRESSOR
TYPE
OIL TYPE
MATERIAL
ROW
OIL AMOUNT
THICKNESS
QUANTITY
INDEX OF PROTECTION (IP)
1
POE
4
TUBE
0.11 / 0.004
MATERIAL
88
Page 90
Components Data (R407C)
mm/in
mm/in
mm/in
cm3/fl.oz.
2510 / 88.3 3250 / 114.4
mm/in
mm/in
mm/in
m2/ft
2
34
mm/in
mm/in
mm/in
m2/ft
2
23
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
PE / 10mm
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
PROPELLER
THREE PHASE INDUCTION MOTOR
DIRECT DRIVE
1
2
0.11 / 0.004
WASHABLE SARANET
ELECTRO GALVANISED MILD STEEL
DIAMETER
THICKNESS
THICKNESS
FACE AREA
COMPRESSOR
TYPE
OIL TYPE
INDEX OF PROTECTION (IP)
QUANTITY
CONDENSER FAN MOTOR
OIL AMOUNT
QUANTITY
CONDENSER FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
DIAMETER
EVAPORATOR FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
DIAMETER
LENGTH
MODEL
TYPE
EVAPORATOR FAN
EVAPORATOR COIL
CONDENSER COIL
FIN
FIN
TUBE
TUBE
CASING
AIR QUALITY FILTER
TYPE
QUANTITY
INSULATION / THICKNESS
SIZE
MATERIAL
EXTERNAL FINISHING
COLOUR
MATERIAL
ROW
FIN PER INCH
DIAMETER
THICKNESS
THICKNESS
FACE AREA
384.5 / 15.1
374.0 / 14.7
660.4 / 26.0
MATERIAL
TYPE
QUANTITY
MATERIAL
MATERIAL
ROW
FIN PER INCH
A4RT150A A4RT200A
BELT DRIVE
CENTRIFUGAL
PLASTIC
2
LIGHT GREY
EPOXY POLYESTER POWDER
16
2
840 / 33.1
667 / 26.3
1 / 0.04
2
POE
0.11 / 0.004
9.52 / 3/8
S.I.G.C.
0.33 / 0.013
ALUMINIUM
2 x 0.57 / 2 x 6.12
15
IP44
2 x 1.25 / 2 x 13.44
IP22
GALVANISED STEEL
2
S.I.G.C.
SCROLL
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
89
Page 91
Components Data (R407C)
mm/in
mm/in 480 / 18.9 481 / 18.9
mm/in
cm3/fl.oz.
3250 / 114.4 4140 / 145.7
mm/in
mm/in
mm/in
m2/ft
2
SEAMLESS COPPER S.I.G.C.
mm/in
mm/in
mm/in
m2/ft
2
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
PE / 10mm
1 / 0.04
SIZE
MATERIAL
EXTERNAL FINISHING
DIAMETER
THICKNESS
THICKNESS
FACE AREA
MATERIAL
DIAMETER
THICKNESS
THICKNESS
FACE AREA
0.11 / 0.004
WASHABLE SARANET
ELECTRO GALVANISED MILD STEEL
LIGHT GREY
EPOXY POLYESTER POWDER
2
14
2
1370 / 53.9
735 / 28.9
812.8 / 32.0
IP54
GALVANISED STEEL
9.52 / 3/8
2
4
SCROLL
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
A4RT300A
BELT DRIVE
CENTRIFUGAL
GALVANISED STEEL
1
ROW
FIN PER INCH
A4RT250A
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
PROPELLER
THREE PHASE INDUCTION MOTOR
DIRECT DRIVE
1
2
CASING
AIR QUALITY FILTER
TYPE
QUANTITY
INSULATION / THICKNESS
COLOUR
EVAPORATOR COIL
CONDENSER COIL
FIN
FIN
TUBE
TUBE
MODEL
TYPE
EVAPORATOR FAN
DIAMETER
LENGTH
EVAPORATOR FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
TYPE
QUANTITY
CONDENSER FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
DIAMETER
COMPRESSOR
TYPE
OIL TYPE
INDEX OF PROTECTION (IP)
QUANTITY
CONDENSER FAN MOTOR
OIL AMOUNT
QUANTITY
2
POE
0.33 / 0.013
ALUMINIUM
2 x 0.91 / 2 x 9.84
14
457.2 / 18
2 x 3.0 / 2 x 32.44
MATERIAL
MATERIAL
MATERIAL
ROW
FIN PER INCH
SEAMLESS COPPER
0.11 / 0.004
IP54
90
Page 92
Components Data (R407C)
mm/in
mm/in
mm/in
320 SZ
cm 3 /fl.oz.
8000 / 281.6
S.I.G.C.
mm/in 7.0 / 0.28
mm/in 0.28 / 0.011
160SZ & 320SZ
6600 / 232.3 & 8000 / 281.6
S.I.G.C.
9.52 / 3/8
0.33 / 0.013
mm/in
m 2 /ft
2
S.I.G.C.
mm/in
mm/in
mm/in
m 2 /ft
2
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
MATERIAL
MATERIAL
MATERIAL
ROW
FIN PER INCH
0.11 / 0.004
3.02 / 32.5
2
0.33 / 0.013
ALUMINIUM
13
COMPRESSOR
TYPE
OIL TYPE
INDEX OF PROTECTION (IP)
QUANTITY
CONDENSER FAN MOTOR
OIL AMOUNT
QUANTITY
CONDENSER FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
DIAMETER
EVAPORATOR FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
TYPE
QUANTITY
MODEL
TYPE
EVAPORATOR FAN
DIAMETER
LENGTH
EVAPORATOR COIL
CONDENSER COIL
FIN
FIN
TUBE
TUBE
CASING
AIR QUALITY FILTER
TYPE
QUANTITY
INSULATION / THICKNESS
COLOUR
ROW
FIN PER INCH
A4RT360A
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
PROPELLER
GALVANISED STEEL
THREE PHASE INDUCTION MOTOR
DIRECT DRIVE
1
IP44
IP54
2
A4RT420A
BELT DRIVE
560 / 22
457 / 18
CENTRIFUGAL
GALVANISED STEEL
1
812.8 / 32.0
9.52 / 3/8
2
4
S.I.G.C.
14 & 13
3 & 4
SCROLL
ALUMINIUM
0.11 / 0.004
3.50 / 37.7
WASHABLE SARANET
ELECTRO GALVANISED MILD STEEL
LIGHT GREY
EPOXY POLYESTER POWDER
860 / 33.86
4 / 0.16
505 / 19.88 & 600 / 23.62
3
13
2 & 3
14 & 13
2 & 4
DIAMETER
THICKNESS
THICKNESS
FACE AREA
DIAMETER
THICKNESS
THICKNESS
FACE AREA
MATERIAL
PE / 10mm
SIZE
MATERIAL
EXTERNAL FINISHING
91
Page 93
Components Data (R407C)
PLASTIC GALVANISED STEEL
mm/in
mm/in 254 / 10 254 / 10 & 203.2 / 8.0
mm/in 609.6 / 24.0 660.4 / 26.0
N/AIP44
cm3/fl.oz.
1770 / 62.3 2510 / 88.3
mm/in
mm/in
mm/in
m2/ft
2
0.53 / 5.700.65 / 6.96
16 15
mm/in
mm/in
mm/in
m2/ft
2
16 13
pc
LENGTH mm/in 820 / 32.3 1020 / 40.2
WIDTH mm/in
THICKNESS mm/in
LIGHT GREY
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
3) * DESIGNATION BASED ON COOLING CYCLE.
615 / 24.2
1 / 0.04
MATERIAL
EXTERNAL FINISHING
AIR QUALITY FILTER
TYPE
QUANTITY
SIZE
MATERIAL
MATERIAL
ROW
FIN PER INCH
DIAMETER
THICKNESS
THICKNESS
FACE AREA
COMPRESSOR
TYPE
OIL TYPE
INDEX OF PROTECTION (IP)
QUANTITY
CONDENSER* FAN MOTOR
OIL AMOUNT
QUANTITY
CONDENSER* FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
DIAMETER
TYPE
QUANTITY
EVAPORATOR* FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
DIAMETER
LENGTH
MODEL
TYPE
EVAPORATOR* FAN
EVAPORATOR* COIL
CONDENSER* COIL
FIN
FIN
TUBE
TUBE
MATERIAL
MATERIAL
ROW
FIN PER INCH
DIAMETER
THICKNESS
THICKNESS
FACE AREA
PE / 10mm
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
CASING
COLOUR
INSULATION / THICKNESS
WASHABLE SARANET
A4RT60AR A4RT80AR
CENTRIFUGAL
2
BELT DRIVE
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
1
PROPELLER
254 / 10
IP22
1
DIRECT DRIVE
INDUCTION MOTOR
1
GALVANISED STEEL
3
S.I.G.C.
9.52 / 3/8
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
14.1 / 15.17
1
2
SCROLL
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
1
POE
S.I.G.C.
92
Page 94
Components Data (R407C)
mm/in
mm/in
mm/in 660.4 / 26.0 762 / 30
IP22 N/A
cm3/fl.oz.
mm/in
mm/in
mm/in
m2/ft
2
0.65 / 6.96 0.65 / 6.99
15 14
mm/in
mm/in
mm/in
m2/ft
2
13 14
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
LIGHT GREY
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
3) * DESIGNATION BASED ON COOLING CYCLE.
615 / 24.2
1 / 0.04
MATERIAL
EXTERNAL FINISHING
AIR QUALITY FILTER
TYPE
QUANTITY
SIZE
THICKNESS
FACE AREA
DIAMETER
THICKNESS
ROW
FIN PER INCH
1
S.I.G.C.
PROPELLER
1
4
S.I.G.C.
3
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
1.42 / 15.28
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
GALVANISED STEEL
BELT DRIVE
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
1
254 / 10
254 / 10 & 203.2 / 8.0
A4RT100AR A4RT120AR
CENTRIFUGAL
2
PE / 10mm
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
CASING
COLOUR
INSULATION / THICKNESS
WASHABLE SARANET
MATERIAL
MATERIAL
ROW
FIN PER INCH
FACE AREA
9.52 / 3/8
THICKNESS
CONDENSER* COIL
FIN
FIN
TUBE
TUBE
MODEL
TYPE
EVAPORATOR* FAN
DIAMETER
LENGTH
TYPE
QUANTITY
EVAPORATOR* FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
CONDENSER* FAN MOTOR
CONDENSER* FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
QUANTITY
INDEX OF PROTECTION (IP)
DIAMETER
COMPRESSOR
TYPE
OIL TYPE
EVAPORATOR* COIL
MATERIAL
MATERIAL
QUANTITY
THICKNESS
OIL AMOUNT
DIAMETER
IP22
GALVANISED STEEL
1
1020 / 40.2
3250 / 114.4
SCROLL
1
POE
DIRECT DRIVE
THREE PHASE INDUCTION MOTOR
93
Page 95
Components Data (R407C)
mm/in
mm/in
mm/in
cm3/fl.oz.
2510 / 88.3 3250 / 114.4
mm/in
mm/in
mm/in
m2/ft
2
34
mm/in
mm/in
mm/in
m2/ft
2
23
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
3) * DESIGNATION BASED ON COOLING CYCLE.
CASING
667 / 26.3
1 / 0.04
MATERIAL
EXTERNAL FINISHING
AIR QUALITY FILTER
TYPE
QUANTITY
SIZE
THICKNESS
THICKNESS
FIN PER INCH
MATERIAL
MATERIAL
DIAMETER
THICKNESS
FACE AREA
DIAMETER
660.4 / 26.0
13
PROPELLER
2
DIRECT DRIVE
THREE PHASE INDUCTION MOTOR
2
S.I.G.C.
2
IP44
COMPRESSOR
TYPE
OIL TYPE
EVAPORATOR* COIL
QUANTITY
MATERIAL
MATERIAL
ROW
THICKNESS
OIL AMOUNT
CONDENSER* FAN MOTOR
CONDENSER* FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
INDEX OF PROTECTION (IP)
QUANTITY
DIAMETER
TYPE
QUANTITY
EVAPORATOR* FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
DIAMETER
MODEL
TYPE
EVAPORATOR* FAN
LENGTH
CONDENSER* COIL
FIN
FIN
TUBE
TUBE
ROW
FIN PER INCH
FACE AREA
PE / 10mm
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
LIGHT GREY
2 x 1.25 / 2 x 13.44
COLOUR
INSULATION / THICKNESS
A4RT150AR A4RT200AR
CENTRIFUGAL
2
PLASTIC
BELT DRIVE
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
1
384.5 / 15.1
374.0 / 14.7
IP22
GALVANISED STEEL
2
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
WASHABLE SARANET
S.I.G.C.
SCROLL
9.52 / 3/8
840 / 33.1
POE
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
2 x 0.57 / 6.12
14
94
Page 96
Components Data (R407C)
mm/in
mm/in 480 / 18.9 481 / 18.9
mm/in
cm3/fl.oz.
3250 / 114.4 4140 / 145.7
SEAMLESS COPPER S.I.G.C.
mm/in
mm/in
mm/in
m2/ft
2
SEAMLESS COPPER S.I.G.C.
mm/in
mm/in
mm/in
m2/ft
2
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
3) * DESIGNATION BASED ON COOLING CYCLE.
735 / 28.9
1 / 0.04
MATERIAL
EXTERNAL FINISHING
AIR QUALITY FILTER
TYPE
QUANTITY
SIZE
DIAMETER
THICKNESS
THICKNESS
FACE AREA
POE
ALUMINIUM
0.11 / 0.004
WASHABLE SARANET
2
14
4
9.52 / 3/8
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
2 x 0.91 / 9.84
14
A4RT250AR A4RT300AR
CENTRIFUGAL
1
PE / 10mm
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
CASING
LIGHT GREYCOLOUR
INSULATION / THICKNESS
CONDENSER* COIL
FIN
FIN
TUBE
TUBE
MODEL
TYPE
EVAPORATOR* FAN
DIAMETER
LENGTH
TYPE
QUANTITY
EVAPORATOR* FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
CONDENSER* FAN MOTOR
CONDENSER* FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
DIAMETER
COMPRESSOR
TYPE
OIL TYPE
EVAPORATOR* COIL
QUANTITY
OIL AMOUNT
DIAMETER
THICKNESS
THICKNESS
FACE AREA
GALVANISED STEEL
MATERIAL
MATERIAL
ROW
INDEX OF PROTECTION (IP)
QUANTITY
BELT DRIVE
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
1
IP54
GALVANISED STEEL
2
1370 / 53.9
PROPELLER
2
DIRECT DRIVE
THREE PHASE INDUCTION MOTOR
812.8 / 32.0
2
SCROLL
ROW
FIN PER INCH
0.33 / 0.013
457.2 / 18
N/A
2 x 3.01 / 2 x 32.44
2
FIN PER INCH
MATERIAL
MATERIAL
95
Page 97
Components Data (R407C)
mm/in
mm/in
mm/in
320 SZ
cm 3 /fl.oz.
8000 / 281.6
S.I.G.C.
160 SZ & 320 SZ
6600 / 232.3 & 8000 / 281.6
S.I.G.C.
mm/in
mm/in
mm/in
m 2 /ft
2
S.I.G.C.
mm/in
mm/in
mm/in
m 2 /ft
2
pc
LENGTH mm/in
WIDTH mm/in
THICKNESS mm/in
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) S.I.G.C. - SEAMLESS INNER GROOVED COPPER.
3) * DESIGNATION BASED ON COOLING CYCLE.
ROW
FIN PER INCH
0.33 / 0.013
2
FIN PER INCH
MATERIAL
MATERIAL
2 & 4
PROPELLER
GALVANISED STEEL
2
DIRECT DRIVE
THREE PHASE INDUCTION MOTOR
812.8 / 32.0
2
SCROLL
GALVANISED STEEL
MATERIAL
MATERIAL
ROW
INDEX OF PROTECTION (IP)
QUANTITY
BELT DRIVE
560 / 22
457 / 18
IP44
IP54
THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
1
COMPRESSOR
TYPE
OIL TYPE
EVAPORATOR* COIL
QUANTITY
OIL AMOUNT
DIAMETER
THICKNESS
THICKNESS
FACE AREA
CONDENSER* FAN MOTOR
CONDENSER* FAN
MATERIAL
DRIVE
TYPE
TYPE
QUANTITY
DIAMETER
TYPE
QUANTITY
EVAPORATOR* FAN MOTOR
QUANTITY
MATERIAL
DRIVE
INDEX OF PROTECTION (IP)
MODEL
TYPE
EVAPORATOR* FAN
DIAMETER
LENGTH
CONDENSER* COIL
FIN
FIN
TUBE
TUBE
PE / 10mm
ELECTRO GALVANISED MILD STEEL
EPOXY POLYESTER POWDER
CASING
LIGHT GREY
860 / 33.86
505 / 19.88 & 600 / 23.62
4 / 0.16
COLOUR
INSULATION / THICKNESS
A4RT360AR A4RT420AR
CENTRIFUGAL
1
4
9.52 / 3/8
9.52 / 3/8
0.33 / 0.013
ALUMINIUM
0.11 / 0.004
3.02 / 32.5
13
S.I.G.C.
3 & 4
14 & 13
ALUMINIUM
0.11 / 0.004
3.50 / 37.7
WASHABLE SARANET
3
13
2 & 3
14 & 13
DIAMETER
THICKNESS
THICKNESS
FACE AREA
AIR QUALITY FILTER
TYPE
QUANTITY
SIZE
MATERIAL
EXTERNAL FINISHING
96
Page 98
Safety Devices (R22)
OPEN kPa/psi
CLOSE kPa/psi
OPEN kPa/psi
CLOSE kPa/psi
DISCHARGE THERMOSTAT SETTING °C / °F
OPEN kPa/psi
CLOSE kPa/psi
OPEN kPa/psi
CLOSE kPa/psi
DISCHARGE THERMOSTAT SETTING °C / °F
OPEN kPa/psi
CLOSE kPa/psi
OPEN kPa/psi
CLOSE kPa/psi
DISCHARGE THERMOSTAT SETTING °C / °F
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
N/A
PHASE SEQUENCER
YES
N/A
SAFETY DEVICE
HIGH PRESSURE SWITCH
TYPE NC
3241 / 470
LOW PRESSURE SWITCH
TYPE N/A
N/A
MODEL
ART150A ART200A
N/A
PHASE SEQUENCER YES
125 / 257
SAFETY DEVICE
HIGH PRESSURE SWITCH
TYPE NC
3241 / 470
LOW PRESSURE SWITCH
TYPE N/A
N/A
MODEL
ART100A ART120A
TYPE
3241 / 470
2648 / 384
2648 / 384
2648 / 384
TYPE
N/A
125 / 257
N/A
N/A
NC
ART60A ART80A
YES
MODEL
SAFETY DEVICE
PHASE SEQUENCER
HIGH PRESSURE SWITCH
LOW PRESSURE SWITCH
OPEN kPa/psi
CLOSE kPa/psi
OPEN kPa/psi
CLOSE kPa/psi
DISCHARGE THERMOSTAT SETTING °C / °F
ART55A
TYPE
3241 / 470
TYPE
NC
2648 / 384
N/A
125 / 257
N/A
N/A
YES
MODEL
SAFETY DEVICE
PHASE SEQUENCER
HIGH PRESSURE SWITCH
LOW PRESSURE SWITCH
97
Page 99
Safety Devices (R22)
OPEN kPa/psi
CLOSE kPa/psi
OPEN kPa/psi
CLOSE kPa/psi
DISCHARGE THERMOSTAT SETTING °C / °F
OPEN kPa/psi
CLOSE kPa/psi
OPEN kPa/psi
CLOSE kPa/psi
DISCHARGE THERMOSTAT SETTING °C / °F
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
N/A
PHASE SEQUENCER YES
SAFETY DEVICE
HIGH PRESSURE SWITCH
TYPE NC
2937 / 426
2413 / 350
LOW PRESSURE SWITCH
TYPE N/A
N/A
MODEL
ART360A ART420A
TYPE
3241 / 470
2648 / 384
TYPE
N/A
N/A
N/A
N/A
N/A
NC
ART250A ART300A
YES
MODEL
SAFETY DEVICE
PHASE SEQUENCER
HIGH PRESSURE SWITCH
LOW PRESSURE SWITCH
98
Page 100
Safety Devices (R22)
OPEN kPa/psi
CLOSE kPa/psi
OPEN kPa/psi
CLOSE kPa/psi
YES
DISCHARGE THERMOSTAT SETTING °C / °F 125 / 257
YES
125 / 257
OPEN kPa/psi
CLOSE kPa/psi
OPEN kPa/psi
CLOSE kPa/psi
YES
YES
DISCHARGE THERMOSTAT SETTING °C / °F 125 / 257
OPEN kPa/psi
CLOSE kPa/psi
OPEN kPa/psi
CLOSE kPa/psi
DISCHARGE THERMOSTAT SETTING °C / °F
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
N/A
PHASE SEQUENCER
N/A
SAFETY DEVICE
HIGH PRESSURE SWITCH
TYPE NC
2937 / 426
LOW PRESSURE SWITCH
TYPE N/A
N/A
ART200AR
SAFETY DEVICE
HIGH PRESSURE SWITCH
TYPE
PHASE SEQUENCER
MODEL
ART150AR
NC
2937 / 426
LOW PRESSURE SWITCH
TYPE N/A
N/A
N/A
MODEL
ART100AR ART120AR
MODEL
SAFETY DEVICE
PHASE SEQUENCER
HIGH PRESSURE SWITCH
LOW PRESSURE SWITCH
TYPE
TYPE
ART60AR ART80AR
N/A
N/A
NC
N/A
2937 / 426
2413 / 350
2413 / 350
2413 / 350
OPEN kPa/psi
CLOSE kPa/psi
OPEN kPa/psi
CLOSE kPa/psi
DISCHARGE THERMOSTAT SETTING °C / °F
MODEL
SAFETY DEVICE
PHASE SEQUENCER
HIGH PRESSURE SWITCH
LOW PRESSURE SWITCH N/A
125 / 257
N/A
N/A
YES
ART55AR
TYPE
2937 / 426
TYPE
NC
2413 / 350
99
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use