Acson AWM 09GR, AWM 09G, AWM 10G, AWM 15G, AWM 15GR Technical Manual

...

Download

Page 1

Wall Mounted Split Systems

AWM - G - 2009

AWM 07G AWM 09G/GR AWM 10G/GR AWM 15G/GR AWM 20G/GR AWM 25G/GR AWM 301/301R

A5WM 07G/GR A5WM 09G/GR A5WM 10G/GR A5WM 15G/GR A5WM 20G/GR A5WM 25G/GR A5WM 311/301R

Models:

Page 2

Page 3

AWM-G-2009 Table of Contents

Table of Contents

Nomenclature......................................................................................................................1

Indoor Unit .....................................................................................................................1

Outdoor Unit ..................................................................................................................2

Product Line-Up .............................................................................................................3

Features...............................................................................................................................9

Application Information ...................................................................................................10

Operating Range ......................................................................................................... 10

Refrigerant Circuit Diagram ......................................................................................... 11

Controller ....................................................................................................................16

Installation Guideline ................................................................................................... 17

Sound Data ........................................................................................................................31

Sound Pressure Level ................................................................................................. 31

NC Curve ..................................................................................................................... 32

Engineering & Physical Data ........................................................................................... 35

General Data .............................................................................................................. 35

Component Data ........................................................................................................51

Performance Data ............................................................................................................. 67

Calculation Steps .........................................................................................................68

Performance Data .......................................................................................................71

Outline and Dimension ....................................................................................................96

Electrical Data ................................................................................................................. 100

Wiring Diagram ............................................................................................................... 108

Service and Maintenance............................................................................................... 117

Troubleshooting .............................................................................................................119

Exploded View and Part List .........................................................................................129

Page 4

Nomenclature AWM-G-2009

Nomenclature

Indoor Unit

AWM10GR

Brand

A : Acson

Refrigerant

“ “

: Omitted if R22

: R407C

: R410A

Model Name

WM : Wall Mounted

Capacity Index

: 10,000 Btu/h

: 20,000 Btu/h

Chassis

: G Series

: J Series

Model Type

“ “

: Omitted if cooling only

: Heatpump

Page 5

AWM-G-2009 Nomenclature

Outdoor Unit

A 5 LC 10 C R

Brand

A : Acson

Refrigerant

“ “

: Omitted if R22

: R407C

: R410A

Model Name

LC : Single Split Condensing Unit

Capacity Index

: 10,000 Btu/h

: 20,000 Btu/h

Chassis

C : C Series

Model Type

“ “

: Omitted if cooling only

: Heatpump

Page 6

Product Line-Up AWM-G-2009

Product Line-Up

Indoor Unit AWM-G Series

AWM

Nomenclature

Classiﬁ cation

PCB

Handset

Air Puriﬁ cation

Grille

Marking

Others

L2.0

G18

Ionizer Filter

Saranet Filter

Negative Ionizer

Nano Technology Air Filteration

Oriﬁ ce Kit

COOLING

07G ACIBE X X X X X X

09G ACIBE X X X X X X

10G ACIBE X X X X X X

15G ACIBE X X X X X X

20G ACIBE X X X X X X

25G ACIBE X X X X X X

301 AFBF X X X X X X

HEATPUMP

09GR ACIBE X X X X X X

10GR ACIBE X X X X X X

15GR ACIBE X X X X X X

20GR ACIBE X X X X X X

25GR ACIBE X X X X X X

301R AFAE X X X X X

Page 7

AWM-G-2009 Product Line-Up

Indoor Unit A5WM-G Series

A5WM

Nomenclature

Classiﬁ cation

PCB

Handset

Air Puriﬁ cation

Grille

Marking

Others

L2.0

G18

Ionizer Filter

Saranet Filter

Negative Ionizer

Nano Technology Air Filteration

COOLING

07G ACIBE X X X X X X

09G ACIBE X X X X X X

10G ACIBE X X X X X X

15G ACIBE X X X X X X

20G ACIBE X X X X X X

25G ACIBE X X X X X X

311 AFCE X X X X X

HEATPUMP

07GR ACIBE X X X X X X

09GR ACIBE X X X X X X

10GR ACIBE X X X X X X

15GR ACIBE X X X X X X

20GR ACIBE X X X X X X

25GR ACIBE X X X X X X

301R AFCE X X X X X

Page 8

Product Line-Up AWM-G-2009

Outdoor Unit ALC-C Series

ALC

Nomenclature

Classiﬁ cation

PCB

Refrigerant Control

FIN

Safety Devices

Compressor

Marking

Others

Special

Cap Tube

Gold Coated

Bare

Contactor

Rotary

Drain Elbow

Low Ambient Kit

COOLING

07C ACPOE X X X X

07C ACPIE X X X X

09C ACPOD X X X X

09C ACPID X X X X

10C ACPOB X X X X

10C ACPIB X X X X

15C ACPOD X X X X

15C ACPID X X X X

18C ACPOD X X X X

18C ACPID X X X X

18C ACPBD X X X X X

20C ACPOD X X X X

20C ACPID X X X X

20C ACPBD X X X X X

25C ACPOD X X X X

25C ACPID X X X X

25C ACPBD X X X X X

28C ACHOB X X X

28C ACHIB X X X

28C ACHBB X X X X

Page 9

AWM-G-2009 Product Line-Up

Outdoor Unit ALC-C Series

ALC

Nomenclature

Classiﬁ cation

PCB

Refrigerant Control

FIN

Safety Devices

Compressor

Marking

Others

Special

Cap Tube

Gold Coated

Bare

Contactor

Rotary

Drain Elbow

Low Ambient Kit

HEATPUMP

09C ACPOD X X X X

09C ACPID X X X X

10C ACPOB X X X X

10C ACPIB X X X X

15C ACPOA X X X X

15C ACPIA X X X X

18C ACPOD X X X X

18C ACPID X X X X

20C ACPOD X X X X

20C ACPID X X X X

25C ACPOD X X X X

25C ACPID X X X X

28C ACHOB X X X X

28C ACHIB X X X X

Page 10

Product Line-Up AWM-G-2009

Outdoor Unit A5LC-C Series

A5LC

Nomenclature

Classiﬁ cation

PCB

Refrigerant Control

FIN

Safety Devices

Compressor

Marking

Others

Special

Cap Tube

Gold Coated

Bare

Contactor

Phase Sequencer

Rotary

Low Ambient Kit

Drain Elbow

COOLING

07C ACPOE X X X X

07C ACPIE X X X X

10C ACPOB X X X X

10C ACPIB X X X X

15C ACPOC X X X X

15C ACPIC X X X X

20C ACPOC X X X X

20C ACPIC X X X X

20C ACPGC X X X X X

20C FCPOC X X X X X X

20C FCPGC X X X X X X X

25C ACPOC X X X X

25C ACPIC X X X X

25C ACPGC X X X X X

25C FCPOC X X X X X X

25C FCPGC X X X X X X X

28C ACPOA X X X X

28C ACPIA X X X X

28C ACPGA X X X X X

28C FCPOA X X X X X X

28C FCPGA X X X X X X X

Page 11

AWM-G-2009 Product Line-Up

Outdoor Unit A5LC-C Series

A5LC

Nomenclature

Classiﬁ cation

PCB

Refrigerant Control

FIN

Safety Devices

Compressor

Marking

Others

Special

Cap Tube

Gold Coated

Bare

Contactor

Phase Sequencer

Rotary

Low Ambient Kit

Drain Elbow

HEATPUMP

07C ACPOE X X X X

07C ACPIE X X X X

10C ACPOB X X X X

10C ACPIB X X X X

15C ACPOC X X X X

15C ACPIC X X X X

20C ACPOC X X X X

20C ACPIC X X X X

20C FCPOC X X X X X X X

25C ACPOC X X X X

25C ACPIC X X X X

25C FCPOC X X X X X X X

28C ACPOA X X X X

28C ACPIA X X X X

28C FCPOA X X X X X X X

Page 12

Features AWM-G-2009

Features

Excellent Air Distribution

Air discharge direction can be adjusted in four directions, manually or automatically by using LCD remote control. The new double louver design with automatic air swing function fully optimizes the room comfort by distributing the air evenly to the room. The unique skew fan design with larger diameter creates better air ﬂ ow to the operating environment.

Self Diagnosis

This function is able to detect and to disgnose any faults occuring in the system by blinking of the LED lights. Simplify and ease for troubleshooting.

Facilitated Maintenance Ensure

The new design of air discharge housing whereby the fan blower can be easily accessed by just losing two screws on the unit to provides a ﬂ exible, faster and easier way to clean up the fan blower and ionizer. Maintenance is easy for electrical components, piping and wiring as these are all easily accessible by merely removing front plastic panel.

High Efﬁ ciency Heat Exchanger

The compact design of the 3-fold structure heat exchanger provides a large surface are for better and efﬁ cient heat exchange. The unique Hydrophilic slit ﬁ n has greatly improved the air ﬂ ow and the contact surfaces with the air thus to boost the cooling capacity.

Wireless Remote Controller

The compact LCD transmitter is able to operate the air conditioner unit within the distance of 9 meters. Fan motor speed can be set at low / medium / high or automatic. Sleep mode auto control will gradually increase or decrease the setting temperature to provide a comfortable surrounding for sleeping. Air ﬂ ow direction can be controlled automatically. Room temperature is controlled by electronic thermostat. The real time timer allows the air conditioner to be switched on and off automatically based on user settings. Turbo mode function is available to enables the required set temperature to be achieved in a short time Personalized Setting allows user to preset and store 2 groups of personal settings (including timer setting) in the handset. Auto random restart is a function whereby when there is power failure occurred during operation, the unit will automatically restart as the last setting condition once the power is resumed.

Rotary Compressors

The ever popular rotary compressor is more energy efﬁ cient and has a higher output to weight ratio.

•

Page 13

AWM-G-2009 Application Information

Application Information

Operating Range

Ensure the operating temperature is in allowable range.

Cooling only

Note :

Standard operating range.

With Low ambient kit. (Optional item) Please refer to local dealer for unit of this specification.

Indoor temp. (°CDB)

Cooling

Outdoor temp. (°CDB)

Indoor temp. (°CWB)

Outdoor temp. (°CDB)

Indoor temp. (°CWB)

Heating

Outdoor temp. (°CWB)

-9

16 21

-5

Standard

point

Low ambient kit

-5

Low ambient kit

Standard

point

Standard

point

! Caution :

The use of your air conditioner outside the range of working temperature and humidity can result in serious failure.

Heatpump

Page 14

Application Information AWM-G-2009

Refrigerant Circuit Diagram

Model: AWM 07G - ALC 07C A5WM 07G - A5LC 07C AWM 09G - ALC 09C A5WM 09G - A5LC 09C AWM 10G - ALC 10C A5WM 10G - A5LC 10C AWM 15G - ALC 15C A5WM 15G - A5LC 15C

Model: AWM 20G - ALC 18C A5WM 20G - A5LC 20C AWM 20G - ALC 20C A5WM 25G - A5LC 25C

Page 15

AWM-G-2009 Application Information

Model: AWM 25G - ALC 25C A5WM 311 - A5LC 28

Model: AWM 301 - ALC 28C

Page 16

Application Information AWM-G-2009

Model: AWM 09GR - ALC 09CR A5WM 07GR - A5LC 07CR

Model: AWM 10GR - ALC 10CR A5WM 09GR - A5LC 10CR A5WM 10GR - A5LC 10CR

Page 17

AWM-G-2009 Application Information

Model: AWM 15GR - ALC 15CR A5WM 15GR - A5LC 15CR

Model: AWM 20GR - ALC 20CR A5WM 20GR - A5LC 20CR A5WM 25GR - A5LC 25CR

Page 18

Application Information AWM-G-2009

Model: AWM 25GR - ALC 25CR

Model: AWM 301R - ALC 28CR A5WM 301R - A5LC 28CR

Page 19

AWM-G-2009 Application Information

Controller

G18

Operation Guide

1 Transmission Source

The source where the signal will be transmitted.•

2 Signal Transmission Indication

Blink to conﬁ rm that the last setting has been transmitted to the unit.

•

3 Temperature Setting

To set the desired room temperature, press the v or V button to increase orde crease the set temperature. The temperature setting range is from 16°C to 30°C (optional setting 20°C to 30°C).

•

4 Personalize Setting

Press

and hold for 3s, then will blink. Press again to cycle between and Set the desire setting, then leave the hand set for 4s without pressing any key and it will save the setting into the programme. Press once to activate the P1 setting, press again to cycle between P1 and P2. Press any key to deactivate the personalize setting.

•

5 Automatic Air Swing (optional)

Press the SWING

button to activate the automatic air swing function. To distribute the air to a speciﬁ c direction, press the SWING button and wait until the louver move to the desired direction and press the button once again.

•

6 Silent Function

Press

for quiet operation. Fan speed turn to minimum speed. Press again to deactivate the function.

•

7 Sleep Mode Setting

Press the SLEEP button will activate the sleep mode function. This function is available under COOL, HEAT and AUTO mode. When the unit is operating under cooling mode, the set temperature is increased by 0.5°C after 30 minutes, 1°C after an hour, and 2°C after 2 hours. When the unit is operating under heating mode, the set temperature is decreased by 1°C after 30 minutes, 2°C after an hour, and 3°C after 2 hours.

•

8 Operating Mode

Press the MODE button to select the type of operating mode. For cooling only unit, the available modes are: COOL (7), DRY (6) and FAN (

•

9 Fan Speed Selection

Press the

button continuously will toggle the fan speed in the following order: Low p Med p High p Auto Stop pressing when the desired fan speed appears on the display screen.

•

10 “ON/OFF” Button

Press one to start the air conditioner unit. Press again to stop the unit.

•

11 Timer Cancel

Press the TIMER CANCEL button to cancel the on timer setting.

•

12 OFF Timer Setting

Press the OFF TIMER button will activate the off timer function. Set the desired off time by pressing the OFF TIMER button continuously.

•

13 ON Timer Setting

Press the ON TIMER button will activate the on timer function. Set the desired on time by pressing the ON TIMER button continuously. If the timer is set to 7.30am, the air conditioner will turn on at 7.30am sharp.

•

14 Turbo Function

Press

for fast cooling. Fan speed turn to maximum speed. Press again to deactivate the function.

•

15 Clock Time Setting

Press

and hold to set the clock time.•

Page 20

Application Information AWM-G-2009

Installation Guideline

Safety Precautions

WARNING

CAUTION

Installation and maintenance should be performed by qualiﬁ ed persons who are familiar with local code and regulation, and experienced with this type of appliance.

All ﬁ eld wiring must be installed in accordance with the national wiring regulation.

Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing wiring work according to the wiring diagram.

The unit must be GROUNDED to prevent possible hazard due to insulation failure.

All electrical wiring must not touch the refrigerant piping or any moving parts of the fan motors.

Conﬁ rm that the unit has been switched OFF before installing or servicing the unit.

Disconnect from the main power supply before servicing the air conditioner unit.

DO NOT pull out the power cord when the power is ON. This may cause serious electrical shocks which may result in ﬁ re hazards.

Keep the indoor and outdoor units, power cable and transmission wiring, at least 1m from TVs and radios, to prevent distorted pictures and static. {Depending on the type and source of the electrical waves, static may be heard even when more than 1m away}.

•

Please take note of the following important points when installing.

Do not install the unit where leakage of ﬂ ammable gas may occur.

If gas leaks and accumulates around the unit, it

may cause ﬁ re ignition.

Ensure that drainage piping is connected properly.

If the drainage piping is not connected properly,

it may cause water leakage which will dampen the furniture.

Do not overcharge the unit.

This unit is factory pre-charged. Overcharge will cause over-current or damage to the compressor.

Ensure that the unit’s panel is closed after service or installation.

Unsecured panels will cause the unit to operate

noisily.

Sharp edges and coil surfaces are potential locations which may cause injury hazards. Avoid from being in contact with these places. Before turning off the power supply, set the remote controller’s ON/OFF switch to the “OFF” position to prevent the nuisance tripping of the unit. If this is

not done, the unit’s fans will start turning automatically when power resumes, posing a hazard to service personnel or the user.

Do not operate any heating apparatus too close to the air conditioner unit. This may cause the plastic panel to

melt or deform as a result of the excessive heat.

Ensure the color of wires of the outdoor unit and the terminal markings are same to the indoors respectively. IMPORTANT : DO NOT INSTALL OR USE THE AIR CONDITIONER UNIT IN A LAUNDRY ROOM. Do not use joined and twisted wires for incoming power supply.

•

NOTICE

Disposal requirements

Your air conditioning product is marked with this symbol. This means that electrical and electronic products shall not be mixed with unsorted household waste. Do not try to dismantle the system yourself: the dismantling of the air conditioning system, treatment of the refrigerant, of oil and of other parts must be done by a qualiﬁ ed installer in accordance with relevant local and national legislation. Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By ensuring this product is disposed of correctly, you will help to prevent potential negative consequences for the environment and human health. Please contact the installer or local authority for more information. Batteries must be removed from the remote controller and disposed of separately in accordance with relevant local and national legislation.

Page 21

AWM-G-2009 Application Information

Installation Diagram

Caution

Before installing the unit, ensure that the power supply matches the power requirement of the airconditioner.•

Page 22

Application Information AWM-G-2009

Selection of Location and Space

Indoor Unit

Install the fan coil (indoor) unit at a location with the following requirements

Location is suitable for wiring, piping and drainage. No obstruction of air ﬂ ow into and out of unit where cooler air can be evenly distributed.(See ﬁ g. 1)·Ensure that air discharge is not short circuited with air intake. Ensure that wall is sufﬁ ciently strong, rigid, ﬂ at, perpendicular and vibration free. Where air ﬁ lter cassette can be slided in or out easily. Where there is no danger of ﬂ ammable gases. Where there is no direct sunlight on unit. Also to take into consideration a place for the installation of the Wireless LCD Remote Controller.

Caution

Do not install unit near the door waybecause excessive fresh air may causepanel condensation on the unit.•

•

Page 23

AWM-G-2009 Application Information

Outdoor Unit

As condensing temperature rises, evaporating temperature rises and cooling capacity drops. In order to achieve maximumcooling capacity, the location selected for outdoor unit should fulﬁ ll the following requirements :

Install the condensing (outdoor) unit in a way such that hot air distributed by the outdoor condensing unit cannot bedrawn in again (as in the case of short circuit of hot discharge air). Allow sufﬁ cient space for maintenance around theunit.

Ensure that there is no obstruction of air ﬂ ow into or out of the unit. Remove obstacles which block air intake ordischarge.

The location must be well ventilated, so that the unit can draw in and distribute plenty of air thus lowering the condensingtemperature. A place capable of bearing the weight of the outdoor unit and isolating noise and vibration. A place protected from direct sunlight. Otherwise use an awning for protection, if necessary.

The location must not be susceptible to dust or oil mist.

Installation Clearance

Outdoor units must be installed such that there is no short circuit of the hot discharge air or obstruction to smooth airﬂ ow. Select the coolest possible place where intake air should not be hotter than the outside temperature (max. 45°C)

ALL MODELS A B C D

Minimum Distance 300 mm 1000 mm 300 mm 500 mm

CAUTION : If the condensing unit is operated in an atmosphere containing oils (including machine oils), salt (coastal area), sulphide gas (near hot spring, oil reﬁ nery plant), such substances may lead to failure of the unit.

Caution

If the condensing unit is operated in an atmosphere containing oils(including machine oils),salt(coastal area), sulphide gas(near hot spring, oil reﬁ nery plant), such substances may lead to failure of theunit.

•

Page 24

Application Information AWM-G-2009

Installation of Outdoor Unit

Condensed Water Disposal of Outdoor Unit (Heat Pump Unit Only)

There are 2 holes on the base of outdoor unit for condensed water to ﬂ ow out. Insert the drain elbow toone of the holes. To install the drain elbow, ﬁ rst insert one portion of the hook to the base (portion A), then pull the drainelbow in the direction shown by the arrow while inserting the other portion to the base. After installation,check to ensure that the drain elbow clings to base ﬁ rmly. If the unit is installed in a snowy and chilly area, condensed water may freeze in the base. In such case,please remove plug at the bottom of unit to smooth the drainage.

•

Page 25

AWM-G-2009 Application Information

Drilling Holes and Mounting Installation Installation Plate

Caution

Please check the unit weight for each model. Always ensure that the wall is sufﬁ ciently strong to withstandthe weight. If not, it is necessary to reinforce the wall with plate, beams or pillars. The unit cannot be directly ﬁ xed onto the wall or the likes. In all cases, the installation plate provided MUSTbe used.

•

Paste the installation plan provided on the desired location on the wall and mark the holes location accordingly. Ensure that the minimum maintenance and servicing space at the top, left and right side of the unit isreserved.·Ensure also the levelness of the installation plate. Drill the screw mounting holes (minimum 4 screws are required). Drill the pipe hole at the location as per plan. (This is only applicable for rear piping outlet installation).

Note: The hole should be drilled slightly lower at outdoor side as per ﬁ gure below:--

Fix the installation plate ﬁ rmly to wall, without tilting to left or right. Use a plumb line, if available.

•

Model DIMENSION “A”

AWM 07/09 G/GR

350.0 mm

A5WM 07/09 G/GR

AWM 10/15 G/GR

400.0 mm

A5WM 10/15 G/GR

MODEL

AWM 20 / 25 G/GR, A5WM 20 / 25 G/GR, AWM 30F / 30FR, A5WM 31F / 30FR

Page 26

Application Information AWM-G-2009

Fixing method:-

WOODENFRAME WALL

REINFORCED CONCRETE BUILDING

NUT ANCHOR BOLT ANCHOR

Indoor Unit Preparation

The refrigerant piping can be routed to the unit in 5direction, by using the cut outs in the unit casing. (See ﬁ g. 1)

Carefully bend the pipes to the required position toalign with the hole. For right hand and rear side drawout, hold the bottom of the piping and ﬁ x directionbefore shaping it to the desired position (See ﬁ g. 2).The condensation drain hose should be taped to thepipes with vinyl tape. The electrical cable can also betaped to the pipes.

Mounting Indoor Unit

Hook the indoor unit onto the upper portion of installation plate. (Engage the 2 hooks of rear top of the indoor unit withthe upper edge of the installation plate). Ensure the hooks are properly seated on the installation plate by moving inleft and right.

Water Drainage Piping

The indoor drain pipe must be downward gradient for smooth drainage. Avoid situation as shown in ﬁ gure below.

•

Page 27

AWM-G-2009 Application Information

Wiring

Electrical Connection

Wiring regulation on wire diameters differ from country to country. Please refer to your LOCAL ELECTRICALCODES for ﬁ eld wiring rules. Be sure that installation comply with such rules and regulations.

General Precautions

Ensure that the rated voltage of the unit corresponds to the name plate before carrying out proper wiringaccording to the wiring diagram. Provide a power outlet to be used exclusively for each unit. A power supply disconnect and a circuit breakerfor over current protection should be provided in the exclusive line. The unit must be GROUNDED to prevent possible hazards due to insulation failures. All wiring must be ﬁ rmly connected. All wiring must not touch the hot refrigerant piping, compressor or any moving parts of fan motors. The ﬁ eld wires from the indoor unit must be clamped on the wire clamp as per shown in the ﬁ gure.

Refrigerant Piping

Maximum pipe Length and Maximum Number of Bends

Always choose the shortest path for refrigerant piping and follow the recommendations as tabulated below:

Model

AWM/A5WM

07G/GR

AWM

09G/GR

AWM/A5WM

10G/GR

AWM/A5WM

15G/GR

AWM/A5WM

20G/GR

AWM/A5WM

25G/GR

A5WM

311/301R

AWM 301/R

Data

Max. Length, L (m) 12 12 12 12 15 15 15

Max. Elevation, H (m) 5555888

Max. No. of Bends 10 10 10 10 10 10 10

Flare Connection

Cut the pipe stages by stages, advancing the blade of pipe cutter slowly.

Remove burr with the burr remover. Hold the ﬂ aring end down to prevent burrs from dropping inside pipe.

•

Page 28

Application Information AWM-G-2009

The exact length of pipe protruding from the face of the ﬂ are die is determined by the ﬂ aring tool. The table showsthe use of an imperial die and riged die.

PIPE Ø, D (mm)

A(mm)

IMPERIAL DIE RIGED DIE

6.35 (1/4”) 1.3 0.7

9.52 (3/8”) 1.6 1

12.7 (1/2”) 1.9 1.3

15.88 (5/8”) 2.2 1.7

Fix the pipe ﬁ rmly on the ﬂ are die. Match the centers of both the ﬂ are die and the ﬂ aring punch, and tightenﬂ aring punch fully.

•

INSTALLATION OF SEPARATE ORIFICE KIT AT OUTDOOR

i) Outdoor Unit Installation Space Is Wide Enough

Directly connect the “Female” nut of oriﬁ ce pipe to the liquid pipe.

•

Orifice Pipe

Liquid Pipe

Flare the liquid pipe and connect it to the “Male” joint of the oriﬁ ce pipe.

•

Page 29

AWM-G-2009 Application Information

ii) Outdoor Installation Space Is Limited

Step 4

Step 3 Step 2

Step 1

Orifice Pipe

If the oriﬁ ce pipe can not be connecteddirectly to the liquid valve due tolimitation space, it can be connectedbetween the liquid pipes.

•

Flare the liquid pipe and connect it to the liquid valve.

•

Liquid Pipe

Brazer

Braze an addition “Male” joint to the liquid pipe.•

Liquid Pipe

Orifice Pipe

Connect the “Female” nut of the oriﬁ ce pipe to the “Male” joint.

•

Liquid Pipe

Orifice Pipe

Flare another liquid pipe and connect it to the “Male”joint of the oriﬁ ce pipe.

•

Page 30

Application Information AWM-G-2009

VACUUMING AND CHARGING

The precharged outdoor unit does not need any vacuuming or charging. However once it is connected, theconnecting pipe line and the indoor need to be vacuumed before releasing the R22/R407C/R410A from theoutdoor unit.

1) Open the service port core cap.

2) Connect pressure gauge to the service port.

3) Connect the line to vacuum pump. Open the charging manifold valve and turn the pump on. Vacuum to–0.1 MPa (-760mmHg) or lower. (Evacuation time varies by the pump but averagely in 1 hour).

Note : R407C – Fix ﬁ lter dryer

R22 - Nil R410A - Nil

4) After evacuation, unscrew the spindle (diagram B) for the gas to run to indoor unit.

•

Page 31

AWM-G-2009 Application Information

4) Decision by low side pressure. Turn compressor on for 10 or 15 min.

gisp²mc/gkgisp²mc/gk AWM 07G 5.2 ~ 5.7 74.3 ~ 81.0 5.7 ~ 6.2 81.9 ~ 89.1 AWM 09G

4.7 ~ 5.5 66.6 ~ 78.6 5.0 ~ 5.8 71.2 ~ 83.1

AWM 10G 4.9 ~ 5.7 70.6 ~ 81.8 5.4 ~ 6.1 76.5 ~ 86.6 AWM 15G 4.7 ~ 5.2 67.6 ~ 74.7 5.2 ~ 5.6 74.0 ~ 80.4 AWM 20G

47~072.5~9.496~668.4~6.4

AWM 25G 37~761.5~7.476~957.4~1.4

AWM 301 4.0 ~ 4.8 56.9 ~ 68.3 4.5 ~ 5.0 64.0 ~ 71.1

AWM 07G R

5.2 ~ 5.8 74.8 ~ 82.3 5.6 ~ 6.1 79.3 ~ 87.7

AWM 09G R 4.8 ~ 5.7 68.9 ~ 81.4 5.2 ~ 5.9 73.7 ~ 84.8 AWM 10G R 4.9 ~ 5.9 70.5 ~ 83.7 5.4 ~ 6.3 76.5 ~ 90.7 AWM 15G R

4.9 ~ 6.3 69.4 ~ 89.3 5.0 ~ 6.6 71.7 ~ 93.8

AWM 20G R 77~074.5~9.4

27~660.5~6.4

AWM 25G R

37~761.5~7.486~068.4~2.4

AWM 301R 4.0 ~ 4.8 56.9 ~ 68.3 4.5 ~ 5.0 64.0 ~ 71.1

A5WM 07 G

9.6 ~ 10.0 137.5 ~ 143.2 10.4 ~ 10.7 148.4 ~ 153.1

A5WM 09G/10G 9.4 ~ 9.9 134.9 ~ 141.8 10.2 ~ 10.6 145.4 ~ 152.1

A5WM 15 G 8.9 ~ 9.3 127.3 ~ 132.3 9.3 ~ 9.7 133.1 ~ 138.1 A5WM 20 G

8.5 ~ 8.8 121 ~ 125 9.3 ~ 9.6 133 ~ 137

A5WM 25 G 8.0 ~ 8.3 114 ~ 118 9.0 ~ 9.2 128 ~ 132

A5WM 31 1 8.0 ~ 8.6 114 ~ 122 8.7 ~ 9.4 124 ~ 133

A5WM 07 GR

9.6 ~ 9.9 136.6 ~ 141.0 10.8 ~ 11.1 154.1 ~ 159.1

A5WM 09GR/10GR 9.4 ~ 9.9 134.4 ~ 141.9 9.9 ~ 10.5 141.4 ~ 149.7

A5WM 15 GR 9.0 ~ 9.4 128.0 ~ 134.2 9.4 ~ 9.9 134.6 ~ 142.0 A5WM 20 GR

8.3 ~ 8.8 119 ~ 125 8.8 ~ 9.2 125 ~ 132

A5WM 25 GR 7.7 ~ 8.3 110 ~ 118 8.4 ~ 9.0 120 ~ 129 A5WM 301R

8.0 ~ 8.6 114 ~ 122 8.7 ~ 9.4 124 ~ 133

Model

noitidnoCdaoLyvaeHnoitidnoCdradnatS

C°

34roodtuO/C°23roodnIC°53roodtuO/C°72roodnI

Within the value refrigerant cycle normal. Lower than value refrigerant cycle has some leaks check, amend and top up is necessary. Extremely low (@ zero) needs evacuation and charge.

Additional Charge

The refrigerant gas is charged in the outdoor unit and, if the piping length is 7.6m, additional charge of therefrigerant after vacuuming is not necessary. When the piping length is more than 7.6m, please use the table below :

Additional charge in gram.

10m 12m 15m 25m 35m

35 65 - - -

35 65 110 - -

90 165 280 - -

90 165 280 650 1030

50 90 - - -

60 110 185 - -

120 220 370 - -

120 220 370 870 1370

35 60 - - -

35 60 100 - -

80 150 255 - -

80 150 255 600 950

45 80 - - -

55 100 165 - -

110 200 335 - -

110 200 335 790 1250

AWM 301R

AWM 301

A5WM 301R

A5WM 311

R410A MODELS

A5WM 07G / 09G / 10G / 15G

A5WM 20G

A5WM 25G

A5WM 07GR / 09GR / 10GR / 15GR

A5WM 20GR

AWM 07G / 09G / 10G / 15G

AWM 20G

R22 MODELS

AWM 25G

AWM 07GR / 09GR / 10GR / 15GR

AWM 20GR

AWM 25GR

A5WM 25GR

•

Page 32

Application Information AWM-G-2009

Diagram shows typical charging method.

Caution For R410A

Avoid prolong exposure of an opened compressor, or the internal part of refrigerant pipingto moist air. The POE oil in the compressor and piping can absorb moisture from air.

•

Final Checking

Ensure that steps 1 to 8 are closely followed.

Ensure the following, in particular :

1) The unit is mounted solidly and rigidly in position.

2) Piping and connections are leak proof after charging.

3) Proper wiring has been done.

Trial run

1) Conduct a trial run after water drainage test and gas leakage test.

2) Watch out for the following : a) Is the electric plug ﬁ rmly inserted into the socket? b) Is there any abnormal sound from unit? c) Is there any abnormal vibrations with regard to unit itself or pipings? d) Is there smooth drainage of water?

Check that :

1) Condenser fan is running, with warm air blowing off the condensing unit.

2) Evaporator blower is running and discharging cool air.

3) Suction (Low side) pressure as per recommended.

4) The remote controller incorporate a 3 minute delay in their circuit. Thus, it requires about 3 minutes uponcut off before the outdoor condensing unit can start up.

SPECIAL PRECAUTIONS WHEN DEALING WITH REFRIGERANT R410A UNIT

1) WHAT IS NEW REFRIGERANT R410A?

R410A is a new HFC refrigerant which does not damage the ozone layer. The working pressure of thisnew refrigerant is 1.6 times higher than conventional refrigerant (R22), thus proper installation / servicingis essential.

2) COMPONENTS

Mixture weight composition R32(50%) and R125(50%)

•

Page 33

AWM-G-2009 Application Information

3) CHARACTERISTIC

R410A liquid and vapor components have different compositions when the ﬂ uid evaporates or condenses.Hence, when leak occurs and only vapor leaks out, the composition of the refrigerant mixture left in thesystem will change and subsequently affect the system performance. DO NOT add new refrigerant toleaked system. It is recommended that the system should be evacuated thoroughly before recharging withR410A. When refrigerant R410A is used, the composition will differ depending on whether it is in gaseous or liquidphase. Hence when charging R410A, ensure that only liquid is being withdrawn from the cylinder or can.This is to make certain that only original composition of R410A is being charged into the system. POE oil is used as lubricant for R410A compressor, which is different from the mineral oil used for R22compressor. Extra precaution must be taken not to expose the R410A system too long to moist air.

4) CHECK LIST BEFORE INSTALLATION/SERVICING

Tubing Refrigerant R410A is more easily affected by dust of moisture compared with R22, make sure to temporarilycover the ends of the tubing prior to installation Compressor oil No additional charge of compressor oil is permitted. Refrigerant No other refrigerant other that R410A Tools (size of service port is different from R22 system) Tools speciﬁ cally for R410A only (must not be used for R22 or other refrigerant) i) Manifold gauge and charging hose ii) Gas leak detector iii) Refrigerant cylinder/charging cylinderiv)Vacuum pump c/w adapter v) Flare tools vi)Refrigerant recovery machine

5) HANDLING AND INSTALLATION GUIDELINES

Like R22 system, the handling and installation of R410A system are closely similar. All precautionary measures;such as ensuring no moisture, no dirt or chips in the system, clean brazing using nitrogen, and thorough leakcheck and vacuuming are equally important requirements. However, due to its hydroscopic POE oil, additionalprecautions must be taken to ensure optimum and trouble free system operation.

a) During installation or servicing, avoid prolong exposure of the internal part of the refrigerant system tomoist

air. Residual POE oil in the piping and components can absorb moisture from the air.

b) Ensure that the compressor is not expose to open air for more than the recommended time speciﬁ ed byits

manufacturer (typically less than 10 minutes). Removed the seal plugs only when the compressor isabout to be brazed.

c) The system should be thoroughly vacuumed to 1.0 Pa ( 700mmHg) or lower. This vacuuming level ismore

stringent than R22 system so as to ensure no incompressible gas and moisture in the system.

d) When charging R410A, ensure that only liquid is being withdrawn from the cylinder or can. This is toensure

that only the original composition of R410A is being delivered into the system. The liquid compositioncan be different from the vapor composition.

Dip-pipe

Liquid withdrawal

Invert cylinder without dip-pipe

f) Normally, the R410A cylinder or can is being equipped with a dip pipe for liquid withdrawal. However,

if thedip pipe is not available, invert the cylinder or can so as to withdraw liquid from the valve at the bottom.

•

Page 34

Sound Data AWM-G-2009

Sound Data

Sound Pressure Level

Model

Speed

(RPM)

1/1 Octave Sound Pressure Level (dB, ref 20μPa)

Overall

(dBA)

Noise

Criteria

125 Hz 250 Hz 500 Hz 1k Hz 2k Hz 4k Hz 8k Hz

AWM 07G AWM 09G/GR A5WM 07G/GR A5WM 09G/GR

High 32 34 38 37 32 23 15 40 36

Medium 27 30 34 32 26 17 14 35 31

Low 24 27 29 26 20 13 13 29 24

AWM 10G/GR A5WM 10G/GR

High 28 34 37 36 31 22 13 39 35

Medium 27 30 33 31 25 17 12 34 30

Low 24 26 28 25 19 12 11 28 23

AWM 15G/GR A5WM 15G/GR

High 30 35 39 38 33 25 15 42 37

Medium 28 31 34 33 26 18 13 36 32

Low 24 26 28 26 20 13 12 29 24

AWM 20G/GR A5WM 20G/GR

High 37 44 42 37 34 25 15 43 37

Medium 34 40 39 34 30 21 14 40 34

Low 30 35 35 30 26 18 13 35 30

AWM 25G/GR A5WM 25G/GR

High 41 48 47 43 40 32 23 49 43

Medium 39 44 43 39 35 28 20 44 38

Low 37 41 40 36 32 25 19 42 35

AWM 301/301R A5WM 311/301R

High 42 46 45 44 41 35 28 49 43

Medium 40 45 44 43 35 33 27 47 42

Low 37 43 43 40 35 30 26 45 39

Microphone position - A5WM/AWM-G/GR : 1m in front and 0.8m below the vertical centre line of the unit. (JIS C 9612)

- A5WM/AWM 30F/FR : 1m in front and 1m below the vertical centre line of the unit. (JIS B 8615)

Model Measuring location

AWM 07G AWM 20G/GR AWM 09G/GR AWM 25G/GR AWM 10G/GR AWM 15G/GR

A5WM 07G/GR A5WM 20G/GR A5WM 09G/GR A5WM 25G/GR A5WM 10G/GR A5WM 15G/GR

Standard : JIS C 9612

A5WM 301/301R A5WM 311/301R

Standard : JIS B 8615

Page 35

AWM-G-2009 Sound Data

Sound pressure level (dB,ref 20μPa)

AWM 07G, 09G/GR , A5WM 07/09G/GR

NC CURVES

125 250 500 1000 2000 4000 8000

Octave-band frequency (Hz)

High Fan

NC-30

NC-35

NC-40

NC-45

Low Fan

Medium Fan

NC-25

NC-20

Sound pressure level (dB,ref 20μPa)

AWM 10G/GR , A5WM 10G/GR

NC CURVES

125 250 500 1000 2000 4000 8000

Octave-band frequency (Hz)

High Fa n

Medium Fan

Low Fan

NC-20

NC-30

NC-45

NC-40

NC-25

NC-35

Page 36

Sound Data AWM-G-2009

Sound pressure level (dB,ref 20μPa)

AWM 15G/GR , A5WM 15G/GR

NC CURVES

125 250 500 1000 2000 4000 8000

Octave-band frequency (Hz)

High Fan

Medium Fan

Low Fan

NC-20

NC-30

NC-45

NC-40

NC-25

NC-35

Sound pressure level (dB,ref 20μPa)

AWM 20G/GR , A5WM 20G/GR

NC CURVES

125 250 500 1000 2000 4000 8000

Octave-band frequency (Hz)

NC-20

NC-25

NC-30

NC-35

NC-40

NC-45

High Fan

Medium Fan

Low Fan

Page 37

AWM-G-2009 Sound Data

Sound pressure level (dB,ref 20μPa)

AWM 25G/GR , A5WM 25G/GR

NC CURVES

125 250 500 1000 2000 4000 8000

Octave-band frequency (Hz)

NC-20

NC-25

NC-30

NC-35

NC-40

NC-45

High Fan

Medium Fan

Low Fan

Octave-band frequency (Hz)

Sound pressure level (dB, ref20μPa)

NC-20

NC-25

NC-35

NC-40

NC-45

NC-50

High Fan

Medium Fan

Low Fan

AWM 301/301R , A5WM 311/301R

NC CURVES

125 250 500 1000 2000 4000 8000

Page 38

Engineering & Physical Data AWM-G-2009

Engineering & Physical Data

General Data - Cooling Only (R22)

MODEL

INDOOR UNIT AWM 07G AWM 09G

OUTDOOR UNIT ALC 07C ALC 09C

NOMINAL CAPACITY

Btu/h 7000 9000

W 2050 2640

NOMINAL TOTAL INPUT POWER W 590 919

NOMINAL RUNNING CURRENT A 2.70 4.10

POWER SOURCE V/Ph/Hz 220 - 240 / 1 / 50 220 - 240 / 1 / 50

EER W/W 3.47 2.87

REFRIGERANT TYPE R22 R22

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 118 / 250 130 / 275

MEDIUM l/s / CFM 104 / 220 106 / 225

LOW l/s / CFM 85 / 180 83 / 175

SOUND PRESSURE LEVEL (H/M/L) dBA 38 / 33 / 28 40 / 35 / 29

UNIT DIMENSION

HEIGHT mm/in 260 / 10.2 260 / 10.2

WIDTH mm/in 799 / 31.5 799 / 31.5

DEPTH mm/in 198 / 7.8 198 / 7.8

PACKING DIMENSION

HEIGHT mm/in 337 / 13.3 337 / 13.3

WIDTH mm/in 857 / 33.7 857 / 33.7

DEPTH mm/in 270 / 10.6 270 / 10.6

UNIT WEIGHT kg/lb 8.5 / 18.7 10 / 22.1

CONDENSATE DRAIN SIZE mm/in 16 / 0.6 16 / 0.6

OUTDOOR UNIT

AIR FLOW l/s / CFM 321 / 680 307 / 650

SOUND PRESSURE LEVEL dBA 45 46

UNIT DIMENSION

HEIGHT mm/in 495 / 19.5 495 / 19.5

WIDTH mm/in 600 / 23.6 600 / 23.6

DEPTH mm/in 245 / 9.7 245 / 9.7

PACKING DIMENSION

HEIGHT mm/in 575 / 22.6 575 / 22.6

WIDTH mm/in 715 / 28.1 715 / 28.1

DEPTH mm/in 330 / 13.0 330 / 13.0

UNIT WEIGHT kg/lb 28 / 61.7 28 / 61.7

PIPE CONNECTION

TYPE FLARE VALVE FLARE VALVE

SIZE

LIQUID mm/in 6.35 / 1/4 6.35 / 1/4

GAS mm/in 9.52 / 3/8 9.52 / 3/8

REFRIGERANT CHARGE kg/lb 0.50 / 1.10 0.53/ 1.16

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 39

AWM-G-2009 Engineering & Physical Data

General Data - Cooling Only (R22)

MODEL

INDOOR UNIT AWM 10G AWM 15G

OUTDOOR UNIT ALC 10C ALC 15C

NOMINAL CAPACITY

Btu/h 9500 12000

W 2780 3520

NOMINAL TOTAL INPUT POWER W 860 1200

NOMINAL RUNNING CURRENT A 3.80 5.40

POWER SOURCE V/Ph/Hz 220 - 240 / 1 / 50 220 - 240 / 1 / 50

EER W/W 3.23 2.93

REFRIGERANT TYPE R22 R22

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 142 / 300 163 / 345

MEDIUM l/s / CFM 118 / 250 135 / 285

LOW l/s / CFM 94 / 200 104 / 220

SOUND PRESSURE LEVEL (H/M/L) dBA 39 / 34 / 28 42 / 36 / 29

UNIT DIMENSION

HEIGHT mm/in 260 / 10.2 260 / 10.2

WIDTH mm/in 799 / 31.5 799 / 31.5

DEPTH mm/in 198 / 7.8 198 / 7.8

PACKING DIMENSION

HEIGHT mm/in 337 / 13.3 337 / 13.3

WIDTH mm/in 957 / 37.7 957 / 37.7

DEPTH mm/in 270 / 10.6 270 / 10.6

UNIT WEIGHT kg/lb 12 / 26.5 12 / 26.5

CONDENSATE DRAIN SIZE mm/in 16 / 0.6 16 / 0.6

OUTDOOR UNIT

AIR FLOW l/s / CFM 396 / 840 453 / 960

SOUND PRESSURE LEVEL dBA 46 49

UNIT DIMENSION

HEIGHT mm/in 540 / 21.3 540 / 21.3

WIDTH mm/in 700 / 27.6 700 / 27.6

DEPTH mm/in 250 / 9.8 250 / 9.8

PACKING DIMENSION

HEIGHT mm/in 620 / 24.4 620 / 24.4

WIDTH mm/in 810 / 31.9 810 / 31.9

DEPTH mm/in 330 / 13.0 330 / 13.0

UNIT WEIGHT kg/lb 32 / 70.5 32 / 70.5

PIPE CONNECTION

TYPE FLARE VALVE FLARE VALVE

SIZE

LIQUID mm/in 6.35 / 1/4 6.35 / 1/4

GAS mm/in 9.52 / 3/8 12.70 / 1/2

REFRIGERANT CHARGE kg/lb 0.63 / 1.39 0.60 / 1.33

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 40

Engineering & Physical Data AWM-G-2009

General Data - Cooling Only (R22)

MODEL

INDOOR UNIT AWM 20G AWM 20G

OUTDOOR UNIT ALC 18C ALC 20C

NOMINAL CAPACITY

Btu/h 18000 19000

W 5280 5570

NOMINAL TOTAL INPUT POWER W 1820 1807

NOMINAL RUNNING CURRENT A 8.10 8.00

POWER SOURCE V/Ph/Hz 220 - 240 / 1 / 50 220 - 240 / 1 / 50

EER W/W 2.90 3.08

REFRIGERANT TYPE R22 R22

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 231 / 490 231 / 490

MEDIUM l/s / CFM 193 / 410 193 / 410

LOW l/s / CFM 160 / 340 160 / 340

SOUND PRESSURE LEVEL (H/M/L) dBA 43 / 40 / 35 43 / 40 / 35

UNIT DIMENSION

HEIGHT mm/in 304 / 12.0 304 / 12.0

WIDTH mm/in 1062 / 41.8 1062 / 41.8

DEPTH mm/in 222 / 8.7 222 / 8.7

PACKING DIMENSION

HEIGHT mm/in 378 / 14.9 378 / 14.9

WIDTH mm/in 1130 / 44.5 1130 / 44.5

DEPTH mm/in 292 / 11.5 292 / 11.5

UNIT WEIGHT kg/lb 16 / 35.3 16 / 35.3

CONDENSATE DRAIN SIZE mm/in 20 / 0.8 20 / 0.8

OUTDOOR UNIT

AIR FLOW l/s / CFM 614 / 1300 614 / 1300

SOUND PRESSURE LEVEL dBA 51 51

UNIT DIMENSION

HEIGHT mm/in 654 / 25.7 654 / 25.7

WIDTH mm/in 855 / 33.7 855 / 33.7

DEPTH mm/in 328 / 12.9 328 / 12.9

PACKING DIMENSION

HEIGHT mm/in 710 / 28.0 710 / 28.0

WIDTH mm/in 990 / 39.0 990 / 39.0

DEPTH mm/in 415 / 16.3 415 / 16.3

UNIT WEIGHT kg/lb 58 / 127.9 59 / 130.1

PIPE CONNECTION

TYPE FLARE VALVE FLARE VALVE

SIZE

LIQUID mm/in 6.35 / 1/4 6.35 / 1/4

GAS mm/in 15.88 / 5/8 15.88 / 5/8

REFRIGERANT CHARGE kg/lb 0.63 / 1.39 0.60 / 1.33

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 41

AWM-G-2009 Engineering & Physical Data

General Data - Cooling Only (R22)

MODEL

INDOOR UNIT AWM 25G AWM 301

OUTDOOR UNIT ALC 25C ALC 28C

NOMINAL CAPACITY

Btu/h 23500 27000

W 6890 7913

NOMINAL TOTAL INPUT POWER W 2530 2708

NOMINAL RUNNING CURRENT A 11.30 13.10

POWER SOURCE V/Ph/Hz 220 - 240 / 1 / 50 220 - 240 / 1 / 50

EER W/W 2.72 3.00

REFRIGERANT TYPE R22 R22

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

AUTO LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 297 / 630 316 / 670

MEDIUM l/s / CFM 231 / 490 297 / 630

LOW l/s / CFM 208 / 440 236 / 500

SOUND PRESSURE LEVEL (H/M/L) dBA 49 / 44 / 42 49 / 47 / 45

UNIT DIMENSION

HEIGHT mm/in 304 / 12.0 360 / 14.2

WIDTH mm/in 1062 / 41.8 1200 / 47.2

DEPTH mm/in 222 / 8.7 200 / 7.9

PACKING DIMENSION

HEIGHT mm/in 378 / 14.9 420 / 16.5

WIDTH mm/in 1130 / 44.5 1267 / 49.9

DEPTH mm/in 292 / 11.5 260 / 10.2

UNIT WEIGHT kg/lb 16 / 35.3 17 / 37.48

CONDENSATE DRAIN SIZE mm/in 20 / 0.8 20 / 0.8

OUTDOOR UNIT

AIR FLOW l/s / CFM 755 / 1600 741 / 1570

SOUND PRESSURE LEVEL dBA 52 54

UNIT DIMENSION

HEIGHT mm/in 756 / 29.8 756 / 29.8

WIDTH mm/in 855 / 33.7 855 / 33.7

DEPTH mm/in 328 / 12.9 328 / 12.9

PACKING DIMENSION

HEIGHT mm/in 810 / 31.9 810 / 31.9

WIDTH mm/in 990 / 39.0 990 / 39.0

DEPTH mm/in 415 / 16.3 415 / 16.3

UNIT WEIGHT kg/lb 62 / 136.7 65 / 143.3

PIPE CONNECTION

TYPE FLARE VALVE FLARE VALVE

SIZE

LIQUID mm/in 9.52 / 3/8 9.52 / 3/8

GAS mm/in 15.88 / 5/8 15.88 / 5/8

REFRIGERANT CHARGE kg/lb 1.5 / 3.30 2.10 / 4.63

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 42

Engineering & Physical Data AWM-G-2009

General Data - Heat pump (R22)

MODEL

INDOOR UNIT AWM 09GR AWM 10GR

OUTDOOR UNIT ALC 09CR ALC 10CR

NOMINAL COOLING CAPACITY

Btu/h 8800 9500

W 2580 2780

NOMINAL HEATING CAPACITY

Btu/h 8600 9500

W 2520 2780

NOMINAL TOTAL INPUT POWER (COOLING) W 910 860

NOMINAL TOTAL INPUT POWER (HEATING) W 750 750

NOMINAL RUNNING CURRENT (COOLING) A 4.00 3.80

NOMINAL RUNNING CURRENT (HEATING) A 3.40 3.40

POWER SOURCE V/Ph/Hz 220 - 240 / 1 / 50 220 - 240 / 1 / 50

EER W/W 2.84 3.23

COP W/W 3.36 3.71

REFRIGERANT TYPE R22 R22

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 130 / 275 142 / 300

MEDIUM l/s / CFM 106 / 225 118 / 250

LOW l/s / CFM 83 / 175 94 / 200

SOUND PRESSURE LEVEL (H/M/L) dBA 40 / 35 / 29 39 / 34 / 28

UNIT DIMENSION

HEIGHT mm/in 260 / 10.2 260 / 10.2

WIDTH mm/in 799 / 31.5 899 / 35.4

DEPTH mm/in 198 / 7.8 198 / 7.8

PACKING DIMENSION

HEIGHT mm/in 337 / 13.3 337 / 13.3

WIDTH mm/in 857 / 33.7 957 / 37.7

DEPTH mm/in 270 / 10.6 270 / 10.6

UNIT WEIGHT kg/lb 10 / 22.5 12 / 26.5

CONDENSATE DRAIN SIZE mm/in 16 / 0.6 16 / 0.6

OUTDOOR UNIT

AIR FLOW l/s / CFM 307 / 650 396 / 840

SOUND PRESSURE LEVEL dBA 46 46

UNIT DIMENSION

HEIGHT mm/in 495 / 19.5 540 / 21.3

WIDTH mm/in 600 / 23.6 700 / 27.6

DEPTH mm/in 245 / 9.7 250 / 9.8

PACKING DIMENSION

HEIGHT mm/in 575 / 22.6 620 / 24.4

WIDTH mm/in 715 / 28.1 810 / 31.9

DEPTH mm/in 330 / 13.0 330 / 13.0

UNIT WEIGHT kg/lb 28 / 61.7 32 / 70.5

PIPE CONNECTION

TYPE FLARE VALVE FLARE VALVE

SIZE

LIQUID mm/in 6.35 / 1/4 6.35 / 1/4

GAS mm/in 9.52 / 3/8 9.52 / 3/8

REFRIGERANT CHARGE kg/lb 0.75/1.65 0.88 / 1.94

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 43

AWM-G-2009 Engineering & Physical Data

General Data - Heat pump (R22)

MODEL

INDOOR UNIT AWM 15GR AWM 20GR

OUTDOOR UNIT ALC 15CR ALC 18CR

NOMINAL COOLING CAPACITY

Btu/h 12000 18000

W 3520 5280

NOMINAL HEATING CAPACITY

Btu/h 12000 18400

W 3520 5390

NOMINAL TOTAL INPUT POWER (COOLING) W 1100 1820

NOMINAL TOTAL INPUT POWER (HEATING) W 980 1660

NOMINAL RUNNING CURRENT (COOLING) A 5.00 8.10

NOMINAL RUNNING CURRENT (HEATING) A 4.50 7.40

POWER SOURCE V/Ph/Hz 220 - 240 / 1 / 50 220 - 240 / 1 / 50

EER W/W 3.20 2.90

COP W/W 3.59 3.25

REFRIGERANT TYPE R22 R22

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 163 / 345 231 / 490

MEDIUM l/s / CFM 135 / 285 193 / 410

LOW l/s / CFM 104 / 220 160 / 340

SOUND PRESSURE LEVEL (H/M/L) dBA 42 / 36 / 29 43 / 40 / 35

UNIT DIMENSION

HEIGHT mm/in 260 / 10.2 304 / 12.0

WIDTH mm/in 799 / 31.5 1062 / 41.8

DEPTH mm/in 198 / 7.8 222 / 8.7

PACKING DIMENSION

HEIGHT mm/in 337 / 13.3 378 / 14.9

WIDTH mm/in 957 / 37.7 1130 / 44.5

DEPTH mm/in 270 / 10.6 292 / 11.5

UNIT WEIGHT kg/lb 12 / 26.5 16 / 35.3

CONDENSATE DRAIN SIZE mm/in 16 / 0.6 20 / 0.8

OUTDOOR UNIT

AIR FLOW l/s / CFM 453 / 960 614 / 1300

SOUND PRESSURE LEVEL dBA 49 51

UNIT DIMENSION

HEIGHT mm/in 540 / 21.3 654 / 25.7

WIDTH mm/in 700 / 27.6 855 / 33.7

DEPTH mm/in 250 / 9.8 328 / 12.9

PACKING DIMENSION

HEIGHT mm/in 620 / 24.4 710 / 28.0

WIDTH mm/in 810 / 31.9 990 / 39.0

DEPTH mm/in 330 / 13.0 415 / 16.3

UNIT WEIGHT kg/lb 32 / 70.5 58 / 127.9

PIPE CONNECTION

TYPE FLARE VALVE FLARE VALVE

SIZE

LIQUID mm/in 6.35 / 1/4 6.35 / 1/4

GAS mm/in 12.7 / 1/2 15.88 / 5/8

REFRIGERANT CHARGE kg/lb 0.80 / 1.76 0.85 / 1.88

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 44

Engineering & Physical Data AWM-G-2009

General Data - Heat pump (R22)

MODEL

INDOOR UNIT AWM 20GR AWM 25GR

OUTDOOR UNIT ALC 20CR ALC 25CR

NOMINAL COOLING CAPACITY

Btu/h 19000 23500

W 5570 6890

NOMINAL HEATING CAPACITY

Btu/h 19500 24000

W 5720 7030

NOMINAL TOTAL INPUT POWER (COOLING) W 1807 2530

NOMINAL TOTAL INPUT POWER (HEATING) W 1757 2450

NOMINAL RUNNING CURRENT (COOLING) A 8.00 11.30

NOMINAL RUNNING CURRENT (HEATING) A 7.80 11.10

POWER SOURCE V/Ph/Hz 220 - 240 / 1 / 50 220 - 240 / 1 / 50

EER W/W 3.08 2.72

COP W/W 3.26 2.87

REFRIGERANT TYPE R22 R22

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 231 / 490 297 / 630

MEDIUM l/s / CFM 193 / 410 231 / 490

LOW l/s / CFM 160 / 340 208 / 440

SOUND PRESSURE LEVEL (H/M/L) dBA 43 / 40 / 35 49 / 44 / 42

UNIT DIMENSION

HEIGHT mm/in 304 / 12.0 304 / 12.0

WIDTH mm/in 1062 / 41.8 1062 / 41.8

DEPTH mm/in 222 / 8.7 222 / 8.7

PACKING DIMENSION

HEIGHT mm/in 378 / 14.9 378 / 14.9

WIDTH mm/in 1130 / 44.5 1130 / 44.5

DEPTH mm/in 292 / 11.5 292 / 11.5

UNIT WEIGHT kg/lb 16 / 35.3 16 / 35.3

CONDENSATE DRAIN SIZE mm/in 20 / 0.8 20 / 0.8

OUTDOOR UNIT

AIR FLOW l/s / CFM 614 / 1300 755 / 1600

SOUND PRESSURE LEVEL dBA 51 52

UNIT DIMENSION

HEIGHT mm/in 654 / 25.7 756 / 29.8

WIDTH mm/in 855 / 33.7 855 / 33.7

DEPTH mm/in 328 / 12.9 328 / 12.9

PACKING DIMENSION

HEIGHT mm/in 710 / 28.0 810 / 31.9

WIDTH mm/in 990 / 39.0 990 / 39.0

DEPTH mm/in 415 / 16.3 415 / 16.3

UNIT WEIGHT kg/lb 59 / 130.1 62 / 136.7

PIPE CONNECTION

TYPE FLARE VALVE FLARE VALVE

SIZE

LIQUID mm/in 6.35 / 1/4 9.52 / 3/8

GAS mm/in 15.88 / 5/8 15.88 / 5/8

REFRIGERANT CHARGE kg/lb 1.35 / 2.99 1.50 / 3.30

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 45

AWM-G-2009 Engineering & Physical Data

General Data - Heat pump (R22)

MODEL

INDOOR UNIT AWM 301R

OUTDOOR UNIT ALC 28CR

NOMINAL COOLING CAPACITY

Btu/h 27000

W 7913

NOMINAL HEATING CAPACITY

Btu/h 27000

W 7913

NOMINAL TOTAL INPUT POWER (COOLING) W 2708

NOMINAL TOTAL INPUT POWER (HEATING) W 2273

NOMINAL RUNNING CURRENT (COOLING) A 13.20

NOMINAL RUNNING CURRENT (HEATING) A 13.30

POWER SOURCE V/Ph/Hz 220 - 240 / 1 / 50

EER W/W 2.92

COP W/W 3.48

REFRIGERANT TYPE R22

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 316 / 670

MEDIUM l/s / CFM 297 / 630

LOW l/s / CFM 236 / 500

SOUND PRESSURE LEVEL (H/M/L) dBA 49 / 47 / 45

UNIT DIMENSION

HEIGHT mm/in 360 / 14.2

WIDTH mm/in 1200 / 47.2

DEPTH mm/in 200 / 7.9

PACKING DIMENSION

HEIGHT mm/in 420 / 16.5

WIDTH mm/in 1267 / 49.9

DEPTH mm/in 260 / 10.2

UNIT WEIGHT kg/lb 17 / 37.48

CONDENSATE DRAIN SIZE mm/in 20 / 0.8

OUTDOOR UNIT

AIR FLOW l/s / CFM 741 / 1570

SOUND PRESSURE LEVEL dBA 54

UNIT DIMENSION

HEIGHT mm/in 756 / 29.8

WIDTH mm/in 855 / 33.7

DEPTH mm/in 328 / 12.9

PACKING DIMENSION

HEIGHT mm/in 810 / 31.9

WIDTH mm/in 990 / 39.0

DEPTH mm/in 415 / 16.3

UNIT WEIGHT kg/lb 68 / 150

PIPE CONNECTION

TYPE FLARE VALVE

SIZE

LIQUID mm/in 9.52 / 3/8

GAS mm/in 15.88 / 5/8

REFRIGERANT CHARGE kg/lb 2.10 / 4.63

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 46

Engineering & Physical Data AWM-G-2009

General Data - Cooling Only (R22)

MODEL

INDOOR UNIT A5WM 07G A5WM 09G

OUTDOOR UNIT A5LC 07C A5LC 10C

NOMINAL CAPACITY

Btu/h 7500 9000

W 2200 2640

NOMINAL TOTAL INPUT POWER W 620 860

NOMINAL RUNNING CURRENT A 2.90 3.90

POWER SOURCE V/Ph/Hz 220 - 240 / 1 / 50 220 - 240 / 1 / 50

EER W/W 3.55 3.07

REFRIGERANT TYPE R410A R410A

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 130 / 275 130 / 275

MEDIUM l/s / CFM 106 / 225 106 / 225

LOW l/s / CFM 83 / 175 83 / 175

SOUND PRESSURE LEVEL (H/M/L) dBA 40 / 35 / 29 40 / 35 / 29

UNIT DIMENSION

HEIGHT mm/in 260 / 10.2 260 / 10.2

WIDTH mm/in 799 / 31.5 799 / 31.5

DEPTH mm/in 198 / 7.8 198 / 7.8

PACKING DIMENSION

HEIGHT mm/in 337 / 13.3 337 / 13.3

WIDTH mm/in 857 / 33.7 857 / 33.7

DEPTH mm/in 270 / 10.6 270 / 10.6

UNIT WEIGHT kg/lb 10 / 22.0 10 / 22.0

CONDENSATE DRAIN SIZE mm/in 16 / 0.6 16 / 0.6

OUTDOOR UNIT

AIR FLOW l/s / CFM 307 / 650 396 / 840

SOUND PRESSURE LEVEL dBA 44 46

UNIT DIMENSION

HEIGHT mm/in 495 / 19.5 540 / 21.3

WIDTH mm/in 600 / 23.6 700 / 27.6

DEPTH mm/in 245 / 9.7 250 / 9.8

PACKING DIMENSION

HEIGHT mm/in 575 / 22.6 620 / 24.4

WIDTH mm/in 715 / 28.1 810 / 31.9

DEPTH mm/in 330 / 13.0 330 / 13.0

UNIT WEIGHT kg/lb 26 / 57.3 32 / 70.5

PIPE CONNECTION

TYPE FLARE VALVE FLARE VALVE

SIZE

LIQUID mm/in 6.35 / 1/4 6.35 / 1/4

GAS mm/in 9.52 / 3/8 9.52 / 3/8

REFRIGERANT CHARGE kg/lb 0.60 / 1.32 0.69 / 1.52

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 47

AWM-G-2009 Engineering & Physical Data

General Data - Cooling Only (R410A)

MODEL

INDOOR UNIT A5WM 10G A5WM 15G

OUTDOOR UNIT A5LC 10C A5LC 15C

NOMINAL CAPACITY

Btu/h 9500 12000

W 2780 3520

NOMINAL TOTAL INPUT POWER W 910 1230

NOMINAL RUNNING CURRENT A 3.90 5.40

POWER SOURCE V/Ph/Hz 220 - 240 / 1 / 50 220 - 240 / 1 / 50

EER W/W 3.05 2.86

REFRIGERANT TYPE R410A R410A

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 142 / 300 163 / 345

MEDIUM l/s / CFM 118 / 250 135 / 285

LOW l/s / CFM 94 / 200 104 / 220

SOUND PRESSURE LEVEL (H/M/L) dBA 39 / 34 / 28 42 / 36 / 29

UNIT DIMENSION

HEIGHT mm/in 260 / 10.2 260 / 10.2

WIDTH mm/in 899 / 35.4 899 / 35.4

DEPTH mm/in 198 / 7.8 198 / 7.8

PACKING DIMENSION

HEIGHT mm/in 337 / 13.3 337 / 13.3

WIDTH mm/in 957 / 37.7 957 / 37.7

DEPTH mm/in 270 / 10.6 270 / 10.6

UNIT WEIGHT kg/lb 12 / 26.5 12 / 26.5

CONDENSATE DRAIN SIZE mm/in 16 / 0.6 16 / 0.6

OUTDOOR UNIT

AIR FLOW l/s / CFM 396 / 840 453 / 960

SOUND PRESSURE LEVEL dBA 46 49

UNIT DIMENSION

HEIGHT mm/in 540 / 21.3 540 / 21.3

WIDTH mm/in 700 / 27.6 700 / 27.6

DEPTH mm/in 250 / 9.8 250 / 9.8

PACKING DIMENSION

HEIGHT mm/in 620 / 24.4 620 / 24.4

WIDTH mm/in 810 / 31.9 810 / 31.9

DEPTH mm/in 330 / 13.0 330 / 13.0

UNIT WEIGHT kg/lb 33 / 70.5 32 / 70.5

PIPE CONNECTION

TYPE FLARE VALVE FLARE VALVE

SIZE

LIQUID mm/in 6.35 / 1/4 6.35 / 1/4

GAS mm/in 9.52 / 3/8 12.70 / 1/2

REFRIGERANT CHARGE kg/lb 0.69 / 1.52 0.80 / 1.76

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 48

Engineering & Physical Data AWM-G-2009

General Data - Cooling Only (R410A)

MODEL

INDOOR UNIT A5WM 20G A5WM 25G

OUTDOOR UNIT A5LC 20C A5LC 25C

NOMINAL CAPACITY-1Ø/ <3Ø>

Btu/h 17850 / <18000> 20350 / <22500>

W 5230 / <5280> 5960 / <6590>

NOMINAL TOTAL INPUT POWER-1Ø/ <3Ø> W 1630 / <1663> 1860 / <2195>

NOMINAL RUNNING CURRENT-1Ø/ <3Ø> A 7.3 / <3.2> 8.4 / <4.2>

POWER SOURCE-1Ø/ <3Ø> V/Ph/Hz 220-240/ 1/ 50 / <380-415/ 3/ 50> 220-240/ 1/ 50 / <380-415/ 3/ 50>

EER-1Ø/ <3Ø> W/W 3.21 / <3.17> 3.21 / <3.00>

REFRIGERANT TYPE R410A R410A

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 231 / 490 297 / 630

MEDIUM l/s / CFM 193 / 410 231 / 490

LOW l/s / CFM 160 / 340 208 / 440

SOUND PRESSURE LEVEL (H/M/L) dBA 43 / 40 / 35 49 / 44 / 42

UNIT DIMENSION

HEIGHT mm/in 304 / 12.0 304 / 12.0

WIDTH mm/in 1062 / 41.8 1062 / 41.8

DEPTH mm/in 222 / 8.7 222 / 8.7

PACKING DIMENSION

HEIGHT mm/in 378 / 14.9 378 / 14.9

WIDTH mm/in 1130 / 44.5 1130 / 44.5

DEPTH mm/in 292 / 11.5 292 / 11.5

UNIT WEIGHT kg/lb 16 / 35.3 16 / 35.3

CONDENSATE DRAIN SIZE mm/in 20 / 0.8 20 / 0.8

OUTDOOR UNIT

AIR FLOW l/s / CFM 614 / 1300 689 / 1460

SOUND PRESSURE LEVEL dBA 52 52

UNIT DIMENSION

HEIGHT mm/in 654 / 25.7 756 / 29.8

WIDTH mm/in 855 / 33.7 855 / 33.7

DEPTH mm/in 328 / 12.9 328 / 12.9

PACKING DIMENSION

HEIGHT mm/in 710 / 28.0 810 / 31.9

WIDTH mm/in 990 / 39.0 990 / 39.0

DEPTH mm/in 415 / 16.3 415 / 16.3

UNIT WEIGHT kg/lb 59 / 130.1 62 / 136.7

PIPE CONNECTION

TYPE FLARE VALVE FLARE VALVE

SIZE

LIQUID mm/in 6.35 / 1/4 6.35 / 1/4

GAS mm/in 12.70 / 1/2 15.88 / 5/8

REFRIGERANT CHARGE kg/lb 1.38 / 3.03 1.54 / 3.40

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 49

AWM-G-2009 Engineering & Physical Data

General Data - Cooling Only (R410A)

MODEL

INDOOR UNIT A5WM 311

OUTDOOR UNIT A5LC - 28C

NOMINAL CAPACITY-1Ø/ <3Ø>

Btu/h 26000 / <26000>

W 7620 / <7620>

NOMINAL TOTAL INPUT POWER-1Ø/ <3Ø> W 2560 / <2631>

NOMINAL RUNNING CURRENT-1Ø/ <3Ø> A 12.2 / <4.6>

POWER SOURCE-1Ø/ <3Ø> V/Ph/Hz 220-240/ 1/ 50 / <380-415/ 3/ 50>

EER-1Ø/ <3Ø> W/W 2.98 / <2.90>

REFRIGERANT TYPE R410A

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

AUTO LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 316 / 670

MEDIUM l/s / CFM 297 / 630

LOW l/s / CFM 236 / 500

SOUND PRESSURE LEVEL (H/M/L) dBA 49 / 47 / 45

UNIT DIMENSION

HEIGHT mm/in 360 / 14.2

WIDTH mm/in 1200 / 47.2

DEPTH mm/in 200 / 7.9

PACKING DIMENSION

HEIGHT mm/in 420 / 16.5

WIDTH mm/in 1267 / 49.9

DEPTH mm/in 260 / 10.2

UNIT WEIGHT kg/lb 17 / 37.5

CONDENSATE DRAIN SIZE mm/in 20 / 0.8

OUTDOOR UNIT

AIR FLOW l/s / CFM 632 / 1340

SOUND PRESSURE LEVEL dBA 54

UNIT DIMENSION

HEIGHT mm/in 756 / 29.8

WIDTH mm/in 855 / 33.7

DEPTH mm/in 328 / 12.9

PACKING DIMENSION

HEIGHT mm/in 810 / 31.9

WIDTH mm/in 990 / 39.0

DEPTH mm/in 415 / 16.3

UNIT WEIGHT kg/lb 68 / 149.9

PIPE CONNECTION

TYPE FLARE VALVE

SIZE

LIQUID mm/in 9.52 / 3/8

GAS mm/in 15.88 / 5/8

REFRIGERANT CHARGE kg/lb 1.75 / 3.86

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 50

Engineering & Physical Data AWM-G-2009

General Data - Heat pump (R410A)

MODEL

INDOOR UNIT A5WM 07GR A5WM 09GR

OUTDOOR UNIT A5LC 07CR A5LC 10CR

NOMINAL COOLING CAPACITY

Btu/h 7500 9000

W 2200 2640

NOMINAL HEATING CAPACITY

Btu/h 7500 9000

W 2200 2640

NOMINAL TOTAL INPUT POWER (COOLING) W 680 860

NOMINAL TOTAL INPUT POWER (HEATING) W 550 745

NOMINAL RUNNING CURRENT (COOLING) A 3.10 3.90

NOMINAL RUNNING CURRENT (HEATING) A 2.60 3.40

POWER SOURCE V/Ph/Hz 220 - 240 / 1 / 50 220 - 240 / 1 / 50

EER W/W 3.24 3.07

COP W/W 4.00 3.54

REFRIGERANT TYPE R410A R410A

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 130 / 275 130 / 275

MEDIUM l/s / CFM 106 / 225 106 / 225

LOW l/s / CFM 83 / 175 83 / 175

SOUND PRESSURE LEVEL (H/M/L) dBA 40 / 35 / 29 40 / 35 / 29

UNIT DIMENSION

HEIGHT mm/in 260 / 10.2 260 / 10.2

WIDTH mm/in 799 / 31.5 799 / 31.5

DEPTH mm/in 198 / 7.8 198 / 7.8

PACKING DIMENSION

HEIGHT mm/in 337 / 13.3 337 / 13.3

WIDTH mm/in 857 / 33.7 857 / 33.7

DEPTH mm/in 270 / 10.6 270 / 10.6

UNIT WEIGHT kg/lb 10 / 22.0 10 / 22.0

CONDENSATE DRAIN SIZE mm/in 16 / 0.6 16 / 0.6

OUTDOOR UNIT

AIR FLOW l/s / CFM 307 / 650 396 / 840

SOUND PRESSURE LEVEL dBA 44 46

UNIT DIMENSION

HEIGHT mm/in 495 / 19.5 540 / 21.3

WIDTH mm/in 600 / 23.6 700 / 27.6

DEPTH mm/in 245 / 9.7 250 / 9.8

PACKING DIMENSION

HEIGHT mm/in 575 / 22.6 620 / 24.4

WIDTH mm/in 715 / 28.1 810 / 31.9

DEPTH mm/in 330 / 13.0 330 / 13.0

UNIT WEIGHT kg/lb 26 / 57.3 32 / 70.5

PIPE CONNECTION

TYPE FLARE VALVE FLARE VALVE

SIZE

LIQUID mm/in 6.35 / 1/4 6.35 / 1/4

GAS mm/in 9.52 / 3/8 9.52 / 3/8

REFRIGERANT CHARGE kg/lb 0.80/1.76 0.73 / 1.61

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 51

AWM-G-2009 Engineering & Physical Data

General Data - Heat pump (R410A)

MODEL

INDOOR UNIT A5WM 10GR A5WM 15GR

OUTDOOR UNIT A5LC 10CR A5LC 15CR

NOMINAL COOLING CAPACITY

Btu/h 9500 12000

W 2780 3520

NOMINAL HEATING CAPACITY

Btu/h 9500 12000

W 2780 3520

NOMINAL TOTAL INPUT POWER (COOLING) W 910 1230

NOMINAL TOTAL INPUT POWER (HEATING) W 770 1080

NOMINAL RUNNING CURRENT (COOLING) A 3.90 5.40

NOMINAL RUNNING CURRENT (HEATING) A 3.40 4.90

POWER SOURCE V/Ph/Hz 220 - 240 / 1 / 50 220 - 240 / 1 / 50

EER W/W 3.05 2.86

COP W/W 3.61 3.26

REFRIGERANT TYPE R410A R410A

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 142 / 300 163 / 345

MEDIUM l/s / CFM 118 / 250 135 / 285

LOW l/s / CFM 94 / 200 104 / 220

SOUND PRESSURE LEVEL (H/M/L) dBA 39 / 34 / 28 42 / 36 / 29

UNIT DIMENSION

HEIGHT mm/in 260 / 10.2 260 / 10.2

WIDTH mm/in 899 / 35.4 899 / 35.4

DEPTH mm/in 198 / 7.8 198 / 7.8

PACKING DIMENSION

HEIGHT mm/in 337 / 13.3 337 / 13.3

WIDTH mm/in 957 / 37.7 957 / 37.7

DEPTH mm/in 270 / 10.6 270 / 10.6

UNIT WEIGHT kg/lb 12 / 26.5 12 / 26.5

CONDENSATE DRAIN SIZE mm/in 16 / 0.6 16 / 0.6

OUTDOOR UNIT

AIR FLOW l/s / CFM 396 / 840 453 / 960

SOUND PRESSURE LEVEL dBA 46 49

UNIT DIMENSION

HEIGHT mm/in 540 / 21.3 540 / 21.3

WIDTH mm/in 700 / 27.6 700 / 27.6

DEPTH mm/in 250 / 9.8 250 / 9.8

PACKING DIMENSION

HEIGHT mm/in 620 / 24.4 620 / 24.4

WIDTH mm/in 810 / 31.9 810 / 31.9

DEPTH mm/in 330 / 13.0 330 / 13.0

UNIT WEIGHT kg/lb 32 / 70.5 32 / 70.5

PIPE CONNECTION

TYPE FLARE VALVE FLARE VALVE

SIZE

LIQUID mm/in 6.35 / 1/4 6.35 / 1/4

GAS mm/in 9.52 / 3/8 12.70 / 1/2

REFRIGERANT CHARGE kg/lb 0.73 / 1.61 0.83 / 1.82

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 52

Engineering & Physical Data AWM-G-2009

General Data - Heat pump (R410A)

MODEL

INDOOR UNIT A5WM 20GR A5WM 25GR

OUTDOOR UNIT A5LC 20CR A5LC 25CR

NOMINAL COOLING CAPACITY- 1Ø / <3Ø>

Btu/h 17850 / <18000> 20350 / <22500>

W 5230 / <5280> 5960 / <6590>

NOMINAL HEATING CAPACITY- 1Ø / <3Ø>

Btu/h 18000 / <18500> 22000 / <23000>

W 5280 / <5420> 6448 / <6740>

NOMINAL TOTAL INPUT POWER (COOLING)- 1Ø / <3Ø> W 1630 / <1663> 1860 / <2195>

NOMINAL TOTAL INPUT POWER (HEATING)- 1Ø / <3Ø> W 1546 / <1630> 1870 / <2106>

NOMINAL RUNNING CURRENT (COOLING)- 1Ø / <3Ø> A 7.2 / <3.2> 8.4 / <4.2>

NOMINAL RUNNING CURRENT (HEATING)- 1Ø / <3Ø> A 6.8 / <3.1> 8.4 / <4.2>

POWER SOURCE- 1Ø / <3Ø> V/Ph/Hz 220-240/ 1/ 50 / <380-415/ 3/ 50> 220-240/ 1/ 50 / <380-415/ 3/ 50>

EER- 1Ø / <3Ø> W/W 3.21 / <3.17> 3.21 / <3.00>

COP- 1Ø / <3Ø> W/W 3.42 / <3.33> 3.45 / <3.20>

REFRIGERANT TYPE R410A R410A

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

DOUBLE LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 231 / 490 297 / 630

MEDIUM l/s / CFM 193 / 410 231 / 490

LOW l/s / CFM 160 / 340 208 / 440

SOUND PRESSURE LEVEL (H/M/L) dBA 43 / 40 / 35 49 / 44 / 42

UNIT DIMENSION

HEIGHT mm/in 304 / 12.0 304 / 12.0

WIDTH mm/in 1062 / 41.8 1062 / 41.8

DEPTH mm/in 222 / 8.7 222 / 8.7

PACKING DIMENSION

HEIGHT mm/in 378 / 14.9 378 / 14.9

WIDTH mm/in 1130 / 44.5 1130 / 44.5

DEPTH mm/in 292 / 11.5 292 / 11.5

UNIT WEIGHT kg/lb 16 / 35.3 16 / 35.3

CONDENSATE DRAIN SIZE mm/in 20 / 0.8 20 / 0.8

OUTDOOR UNIT

AIR FLOW l/s / CFM 614 / 1300 689 / 1460

SOUND PRESSURE LEVEL dBA 52 52

UNIT DIMENSION

HEIGHT mm/in 654 / 25.7 756 / 29.8

WIDTH mm/in 855 / 33.7 855 / 33.7

DEPTH mm/in 328 / 12.9 328 / 12.9

PACKING DIMENSION

HEIGHT mm/in 710 / 28.0 810 / 31.9

WIDTH mm/in 990 / 39.0 990 / 39.0

DEPTH mm/in 415 / 16.3 415 / 16.3

UNIT WEIGHT kg/lb 59 / 130.1 62 / 136.7

PIPE CONNECTION

TYPE FLARE VALVE FLARE VALVE

SIZE

LIQUID mm/in 6.35 / 1/4 6.35 / 1/4

GAS mm/in 12.70 / 1/2 15.88 / 5/8

REFRIGERANT CHARGE kg/lb 1.38 / 3.03 1.54 / 3.40

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 53

AWM-G-2009 Engineering & Physical Data

General Data - Heat pump (R410A)

MODEL

INDOOR UNIT A5WM 301R

OUTDOOR UNIT A5LC 28CR

NOMINAL COOLING CAPACITY- 1Ø / <3Ø>

Btu/h 26000 / <26000>

W 7620 / <7620>

NOMINAL HEATING CAPACITY- 1Ø / <3Ø>

Btu/h 26000 / <26000>

W 7620 / <7620>

NOMINAL TOTAL INPUT POWER (COOLING)- 1Ø / <3Ø> W 2560 / <2631>

NOMINAL TOTAL INPUT POWER (HEATING)- 1Ø / <3Ø> W 2442 / <2294>

NOMINAL RUNNING CURRENT (COOLING)- 1Ø / <3Ø> A 12.2 / <4.6>

NOMINAL RUNNING CURRENT (HEATING)- 1Ø / <3Ø> A 11.6 / <4.2>

POWER SOURCE- 1Ø / <3Ø> V/Ph/Hz 220-240/ 1/ 50 / <380-415/ 3/ 50>

EER- 1Ø / <3Ø> W/W 2.98 / <2.90>

COP- 1Ø / <3Ø> W/W 3.12 / <3.32>

REFRIGERANT TYPE R410A

REFRIGERANT CONTROL (EXPANSION DEVICE) OUTDOOR CAP. TUBE

INDOOR UNIT

CONTROL

AIR DISCHARGE

AUTO LOUVER (UP & DOWN) &

GRILLE (LEFT & RIGHT)

OPERATION LCD REMOTE CONTROL

AIR FLOW

HIGH l/s / CFM 316 / 670

MEDIUM l/s / CFM 297 / 630

LOW l/s / CFM 236 / 500

SOUND PRESSURE LEVEL (H/M/L) dBA 49 / 47 / 45

UNIT DIMENSION

HEIGHT mm/in 360 / 14.2

WIDTH mm/in 1200 / 47.2

DEPTH mm/in 200 / 7.9

PACKING DIMENSION

HEIGHT mm/in 420 / 16.5

WIDTH mm/in 1267 / 49.9

DEPTH mm/in 260 / 10.2

UNIT WEIGHT kg/lb 17 / 37.5

CONDENSATE DRAIN SIZE mm/in 20 / 0.8

OUTDOOR UNIT

AIR FLOW l/s / CFM 632 / 1340

SOUND PRESSURE LEVEL dBA 54

UNIT DIMENSION

HEIGHT mm/in 756 / 29.8

WIDTH mm/in 855 / 33.7

DEPTH mm/in 328 / 12.9

PACKING DIMENSION

HEIGHT mm/in 810 / 31.9

WIDTH mm/in 990 / 39.0

DEPTH mm/in 415 / 16.3

UNIT WEIGHT kg/lb 68 / 149.9

PIPE CONNECTION

TYPE FLARE VALVE

SIZE

LIQUID mm/in 9.52 / 3/8

GAS mm/in 15.88 / 5/8

REFRIGERANT CHARGE kg/lb 1.75 / 3.86

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.

3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :

a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR

4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

Page 54

Engineering & Physical Data AWM-G-2009

Component Data - Cooling Only (R22)

MODEL

INDOOR UNIT AWM 07G AWM 09G

OUTDOOR UNIT ALC 07C ALC 09C

INDOOR FAN

TYPE CROSS FLOW FAN CROSS FLOW FAN

QUANTITY 11

MATERIAL ACRYLO NITRILE STYRENE ACRYLO NITRILE STYRENE

DRIVE DIRECT DIRECT

DIAMETER mm/in 97 / 3.8 97 / 3.8

LENGTH mm/in 617.5 / 24.3 617.5 / 24.3

INDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP24 IP24

OUTDOOR FAN

TYPE PROPELLER PROPELLER

QUANTITY 11

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT DIRECT

DIAMETER mm/in 356 / 14 356 / 14

OUTDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP54 IP54

COMPRESSOR

TYPE ROTARY HERMETIC ROTARY HERMETIC

OIL TYPE ATMOS M60 or SUNISO 4GDID ATMOS M60 or SUNISO 4GDID

OIL AMOUNT cm

/ ﬂ .oz. 320 / 11.3 320 / 11.3

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.201 / 2.161 0.201 / 2.161

ROW 22

FIN PER INCH 18 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL RASE LANCE RASE LANCE

THICKNESS mm/in 0.10 / 0.004 0.10 / 0.004

FACE AREA m2/ft

0.31 / 3.40 0.31 / 3.40

ROW 11

FIN PER INCH 18 18

AIR QUALITY

FILTER

TYPE NANO FILTER NANO FILTER

QUANTITY pc 22

SIZE

LENGTH mm/in 304 / 11.9 304 / 11.9

WIDTH mm/in 298 / 11.7 298 / 11.7

THICKNESS mm/in 1.5 / 0.06 1.5 / 0.06

NEGATIVE IONIZER YES YES

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE HIGH IMPACT POLYSTYRENE

COLOUR LIGHT GREY LIGHT GREY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL GALVANISED MILD STEEL

COLOUR LIGHT GREY LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 55

AWM-G-2009 Engineering & Physical Data

Component Data - Cooling Only (R22)

MODEL

INDOOR UNIT AWM 10G AWM 15G

OUTDOOR UNIT ALC 10C ALC 15C

INDOOR FAN

TYPE CROSS FLOW FAN CROSS FLOW FAN

QUANTITY 11

MATERIAL ACRYLO NITRILE STYRENE ACRYLO NITRILE STYRENE

DRIVE DIRECT DIRECT

DIAMETER mm/in 97 / 3.8 97 / 3.8

LENGTH mm/in 717.5 / 28.2 717.5 / 28.2

INDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP24 IP24

OUTDOOR FAN

TYPE PROPELLER PROPELLER

QUANTITY 11

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT DIRECT

DIAMETER mm/in 404 / 16 404 / 16

OUTDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP54 IP54

COMPRESSOR

TYPE ROTARY HERMETIC ROTARY HERMETIC

OIL TYPE ATMOS M60 or SUNISO 4GDID ATMOS M60 or SUNISO 4GDID

OIL AMOUNT cm

/ ﬂ .oz. 320 / 11.3 350 / 11.8

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.234 / 2.516 0.234 / 2.516

ROW 22

FIN PER INCH 18 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL CORRUGATED RASE LANCE

THICKNESS mm/in 0.11 / 0.004 0.11 / 0.004

FACE AREA m

/ft

0.36 / 3.94 0.36 / 3.94

ROW 11

FIN PER INCH 18 18

AIR QUALITY

FILTER

TYPE NANO FILTER NANO FILTER

QUANTITY pc 22

SIZE

LENGTH mm/in 304 / 11.9 304 / 11.9

WIDTH mm/in 348 / 13.7 348 / 13.7

THICKNESS mm/in 1.5 / 0.06 1.5 / 0.06

NEGATIVE IONIZER YES YES

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE HIGH IMPACT POLYSTYRENE

COLOUR LIGHT GREY LIGHT GREY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL GALVANISED MILD STEEL

COLOUR LIGHT GREY LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 56

Engineering & Physical Data AWM-G-2009

Component Data - Cooling Only (R22)

MODEL

INDOOR UNIT AWM 20G AWM 20G

OUTDOOR UNIT ALC 18C ALC 20C

INDOOR FAN

TYPE CROSS FLOW FAN CROSS FLOW FAN

QUANTITY 11

MATERIAL ACRYLO NITRILE STYRENE ACRYLO NITRILE STYRENE

DRIVE DIRECT DIRECT

DIAMETER mm/in 108 / 4.25 108 / 4.25

LENGTH mm/in 810 / 31.9 810 / 31.9

INDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP20 IP20

OUTDOOR FAN

TYPE PROPELLER PROPELLER

QUANTITY 11

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT DIRECT

DIAMETER mm/in 457.2 / 18 457.2 / 18

OUTDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP54 IP54

COMPRESSOR

TYPE ROTARY HERMETIC ROTARY HERMETIC

OIL TYPE ATMOS NM56M or SUNISO 4GDID ATMOS NM56M or SUNISO 4GDID

OIL AMOUNT cm

/ ﬂ .oz. 600 / 21.1 1000 / 35.2

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.269 / 2.900 0.269 / 2.900

ROW 22

FIN PER INCH 18 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL ALUMINIUM (RAISE LANCE FIN) ALUMINIUM (RAISE LANCE FIN)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.52 / 5.59 0.52 / 5.59

ROW 12

FIN PER INCH 20 18

AIR QUALITY

FILTER

TYPE NANO FILTER NANO FILTER

QUANTITY pc 22

SIZE

LENGTH mm/in 351/13.8 351/13.8

WIDTH mm/in 386 / 15.2 386 / 15.2

THICKNESS mm/in 1.5 / 0.06 1.5 / 0.06

NEGATIVE IONIZER YES YES

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE HIGH IMPACT POLYSTYRENE

COLOUR LIGHT GREY LIGHT GREY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL GALVANISED MILD STEEL

COLOUR LIGHT GREY LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 57

AWM-G-2009 Engineering & Physical Data

Component Data - Cooling Only (R22)

MODEL

INDOOR UNIT AWM 25G AWM 301

OUTDOOR UNIT ALC 25C ALC 28C

INDOOR FAN

TYPE CROSS FLOW FAN CROSS FLOW FAN

QUANTITY 11

MATERIAL ACRYLO NITRILE STYRENE ACRYLO NITRILE STYRENE

DRIVE DIRECT DIRECT

DIAMETER mm/in 108 / 4.25 106 / 4.17

LENGTH mm/in 810 / 31.9 950 / 37.4

INDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP20 IP24

OUTDOOR FAN

TYPE PROPELLER PROPELLER

QUANTITY 11

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT DIRECT

DIAMETER mm/in 457.2 / 18 457.2 / 18

OUTDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP54 IP54

COMPRESSOR

TYPE ROTARY HERMETIC ROTARY HERMETIC

OIL TYPE ATMOS NM56M or SUNISO 4GDID ATMOS NM56M or SUNISO 4GDID

OIL AMOUNT cm

/ ﬂ .oz. 700 / 24.6 1130 / 39.8

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 9.52 / 0.375

THICKNESS mm/in 0.28 / 0.011 0.35 / 0.013

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.269 / 2.900 0.291 / 3.130

ROW 22

FIN PER INCH 18 16

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 9.52 / 3/8

THICKNESS mm/in 0.28 / 0.011 0.33 / 0.013

FIN

MATERIAL RAISE LANCE ALUMINIUM (SLIT FIN)

THICKNESS mm/in 0.127 / 0.005 0.127 / 0.005

FACE AREA m

/ft

0.61 / 6.52 0.61 / 6.52

ROW 22

FIN PER INCH 18 18

AIR QUALITY

FILTER

TYPE NANO FILTER SARANET + IONIZER

QUANTITY pc 2 3 X 3

SIZE

LENGTH mm/in 351/13.8 330 / 13.0

WIDTH mm/in 386 / 15.2 317 / 12.4

THICKNESS mm/in 1.5 / 0.06 1.8 / 0.07

NEGATIVE IONIZER YES NO

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE ABS

COLOUR LIGHT GREY LIGHT GREY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL GALVANISED MILD STEEL

COLOUR LIGHT GREY LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 58

Engineering & Physical Data AWM-G-2009

Component Data - Heat Pump (R22)

MODEL

INDOOR UNIT AWM 09GR AWM 10GR

OUTDOOR UNIT ALC 09CR ALC 10CR

INDOOR FAN

TYPE ANTI FUNGUS SKEW FAN ANTI FUNGUS SKEW FAN

QUANTITY 11

MATERIAL ACRYLO NITRILE STYRENE ACRYLO NITRILE STYRENE

DRIVE DIRECT DIRECT

DIAMETER mm/in 97 / 3.8 97 / 3.8

LENGTH mm/in 617.5 / 24.3 717.5 / 28.2

INDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP24 IP24

OUTDOOR FAN

TYPE PROPELLER PROPELLER

QUANTITY 11

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT DIRECT

DIAMETER mm/in 356 / 14 404 / 16

OUTDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP54 IP54

COMPRESSOR

TYPE ROTARY HERMETIC ROTARY HERMETIC

OIL TYPE ATMOS M60 or SUNISO 4GDID ATMOS M60 or SUNISO 4GDID

OIL AMOUNT cm

/ ﬂ .oz. 320 / 11.3 320 / 11.3

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.201 / 2.161 0.234 / 2.516

ROW 22

FIN PER INCH 18 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 9.52 / 3/8 9.52 / 3/8

THICKNESS mm/in 0.33 / 0.013 0.33 / 0.013

FIN

MATERIAL ALUMINIUM (SLIT FIN) ALUMINIUM (SLIT FIN)

THICKNESS mm/in 0.11 / 0.004 0.11 / 0.004

FACE AREA m

/ft

0.31 / 3.40 0.36 / 3.94

ROW 11

FIN PER INCH 18 18

AIR QUALITY

FILTER

TYPE NANO FILTER NANO FILTER

QUANTITY pc 22

SIZE

LENGTH mm/in 304 / 11.9 304 / 11.9

WIDTH mm/in 298 / 11.7 348 / 13.7

THICKNESS mm/in 1.5 / 0.06 1.5 / 0.06

NEGATIVE IONIZER YES YES

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE HIGH IMPACT POLYSTYRENE

COLOUR LIGHT GREY LIGHT GREY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL GALVANISED MILD STEEL

COLOUR LIGHT GREY LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 59

AWM-G-2009 Engineering & Physical Data

Component Data - Heat Pump (R22)

MODEL

INDOOR UNIT AWM 15GR AWM 20GR

OUTDOOR UNIT ALC 15CR ALC 18CR

INDOOR FAN

TYPE ANTI FUNGUS SKEW FAN CROSS FLOW FAN

QUANTITY 11

MATERIAL ACRYLO NITRILE STYRENE ACRYLO NITRILE STYRENE

DRIVE DIRECT DIRECT

DIAMETER mm/in 97 / 3.8 108 / 4.25

LENGTH mm/in 717.5 / 28.2 810 / 31.9

INDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP24 IP20

OUTDOOR FAN

TYPE PROPELLER PROPELLER

QUANTITY 11

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT DIRECT

DIAMETER mm/in 404 / 16 457.2/18

OUTDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP54 IP54

COMPRESSOR

TYPE ROTARY HERMETIC ROTARY HERMETIC

OIL TYPE ATMOS M60 or SUNISO 4GDID ATMOS NM56M or SUNISO 4GDID

OIL AMOUNT cm

/ ﬂ .oz. 350 / 11.8 600 / 21.1

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.234 / 2.516 0.269 / 2.900

ROW 22

FIN PER INCH 18 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 9.52 / 3/8 7.0 / 0.276

THICKNESS mm/in 0.33 / 0.013 0.28 / 0.011

FIN

MATERIAL ALUMINIUM (SLIT FIN) ALUMINIUM (RAISE LANCE FIN)

THICKNESS mm/in 0.11 / 0.004 0.11 / 0.0043

FACE AREA m

/ft

0.36 / 3.94 0.52 / 5.59

ROW 11

FIN PER INCH 18 20

AIR QUALITY

FILTER

TYPE NANO FILTER NANO FILTER

QUANTITY pc 22

SIZE

LENGTH mm/in 304 / 11.9 351 / 13.8

WIDTH mm/in 348 / 13.7 386 / 15.2

THICKNESS mm/in 1.5 / 0.06 1.5 / 0.06

NEGATIVE IONIZER YES YES

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE HIGH IMPACT POLYSTYRENE

COLOUR LIGHT GREY LIGHT GREY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL GALVANISED MILD STEEL

COLOUR LIGHT GREY LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 60

Engineering & Physical Data AWM-G-2009

Component Data - Heat Pump (R22)

MODEL

INDOOR UNIT AWM 20GR AWM 25GR

OUTDOOR UNIT ALC 20CR ALC 25CR

INDOOR FAN

TYPE ANTI FUNGUS SKEW FAN ANTI FUNGUS SKEW FAN

QUANTITY 11

MATERIAL ACRYLO NITRILE STYRENE ACRYLO NITRILE STYRENE

DRIVE DIRECT DIRECT

DIAMETER mm/in 108 / 4.25 108 / 4.25

LENGTH mm/in 810 / 31.9 810 / 31.9

INDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP20 IP20

OUTDOOR FAN

TYPE PROPELLER PROPELLER

QUANTITY 11

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT DIRECT

DIAMETER mm/in 457.2 / 18 457.2 / 18

OUTDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP54 IP54

COMPRESSOR

TYPE ROTARY HERMETIC ROTARY HERMETIC

OIL TYPE RB68A ORFREOL ALPHA68M RB68A ORFREOL ALPHA68M

OIL AMOUNT cm

/ ﬂ .oz. 670 / 23.5 1130 / 39.7

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.269 / 2.900 0.269 / 2.900

ROW 22

FIN PER INCH 18 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL ALUMINIUM (CORR. FIN) ALUMINIUM (CORR. FIN)

THICKNESS mm/in 0.127 / 0.005 0.127 / 0.005

FACE AREA m

/ft

0.51 / 5.47 0.62 / 6.64

ROW 22

FIN PER INCH 18 18

AIR QUALITY

FILTER

TYPE NANO FILTER NANO FILTER

QUANTITY pc 22

SIZE

LENGTH mm/in 351/13.8 351/13.8

WIDTH mm/in 386 / 15.2 386 / 15.2

THICKNESS mm/in 1.5 / 0.06 1.5 / 0.06

NEGATIVE IONIZER YES YES

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE HIGH IMPACT POLYSTYRENE

COLOUR IVORY IVORY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL GALVANISED MILD STEEL

COLOUR LIGHT GREY LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 61

AWM-G-2009 Engineering & Physical Data

Component Data - Heat Pump (R22)

MODEL

INDOOR UNIT AWM 301R

OUTDOOR UNIT ALC 28CR

INDOOR FAN

TYPE ANTI FUNGUS CROSS FLOW FAN

QUANTITY 1

MATERIAL ACRYLO NITRILE STYRENE

DRIVE DIRECT

DIAMETER mm/in 106 / 4.17

LENGTH mm/in 950 / 37.4

INDOOR FAN MOTOR

TYPE INDUCTION

QUANTITY 1

INDEX OF PROTECTION (IP) IP24

OUTDOOR FAN

TYPE PROPELLER

QUANTITY 1

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT

DIAMETER mm/in 457.2/18

OUTDOOR FAN MOTOR

TYPE INDUCTION

QUANTITY 1

INDEX OF PROTECTION (IP) IP54

COMPRESSOR

TYPE ROTARY HERMETIC

OIL TYPE ATMOS M60 or SUNISO 4GDID

OIL AMOUNT cm

/ ﬂ .oz. 1130 / 39.8

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 9.52 / 0.375

THICKNESS mm/in 0.35 / 0.013

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043

FACE AREA m

/ft

0.291 / 3.130

ROW 2

FIN PER INCH 16

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 9.52 / 3/8

THICKNESS mm/in 0.33 / 0.013

FIN

MATERIAL ALUMINIUM (SLIT FIN)

THICKNESS mm/in 0.11 / 0.004

FACE AREA m

/ft

0.61 / 6.52

ROW 2

FIN PER INCH 18

AIR QUALITY

FILTER

TYPE SARANET + IONIZER

QUANTITY pc 3 X 3

SIZE

LENGTH mm/in 330 / 13.0

WIDTH mm/in 317 / 12.4

THICKNESS mm/in 1.8 / 0.07

NEGATIVE IONIZER NO

CASING

INDOOR UNIT

MATERIAL ABS

COLOUR LIGHT GREY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL

COLOUR LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 62

Engineering & Physical Data AWM-G-2009

Component Data - Cooling Only (R410A)

MODEL

INDOOR UNIT A5WM 07G A5WM 09G

OUTDOOR UNIT A5LC 07C A5LC 10C

INDOOR FAN

TYPE ANTI FUNGUS SKEW FAN ANTI FUNGUS SKEW FAN

QUANTITY 11

MATERIAL ACRYLO NITRILE STYRENE ACRYLO NITRILE STYRENE

DRIVE DIRECT DIRECT

DIAMETER mm/in 97 / 3.8 97 / 3.8

LENGTH mm/in 617.5 / 24.3 617.5 / 24.3

INDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP24 IP24

OUTDOOR FAN

TYPE PROPELLER PROPELLER

QUANTITY 11

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT DIRECT

DIAMETER mm/in 356 / 14 356 / 14

OUTDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP54 IP54

COMPRESSOR

TYPE ROTARY HERMETIC ROTARY HERMETIC

OIL TYPE RB68A OR FREOL ALPHA68M RB68A OR FREOL ALPHA68M

OIL AMOUNT cm

/ ﬂ .oz. 300 / 10.5 350 / 12.3

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.201 / 2.161 0.201 / 2.161

ROW 22

FIN PER INCH 18 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 9.52 / 3/8 9.52 / 3/8

THICKNESS mm/in 0.33 / 0.013 0.33 / 0.013

FIN

MATERIAL ALUMINIUM (SLIT FIN) ALUMINIUM (SLIT FIN)

THICKNESS mm/in 0.11/0.004 0.11/0.004

FACE AREA m

/ft

0.31 / 3.40 0.36 / 3.94

ROW 11

FIN PER INCH 18 18

AIR QUALITY

FILTER

TYPE NANO FILTER NANO FILTER

QUANTITY pc 22

SIZE

LENGTH mm/in 304 / 11.9 304 / 11.9

WIDTH mm/in 298 / 11.7 298 / 11.7

THICKNESS mm/in 1.5 / 0.06 1.5 / 0.06

NEGATIVE IONIZER YES YES

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE HIGH IMPACT POLYSTYRENE

COLOUR IVORY IVORY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL GALVANISED MILD STEEL

COLOUR LIGHT GREY LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 63

AWM-G-2009 Engineering & Physical Data

Component Data - Cooling Only (R410A)

MODEL

INDOOR UNIT A5WM 10G A5WM 15G

OUTDOOR UNIT A5LC 10C A5LC 15C

INDOOR FAN

TYPE ANTI FUNGUS SKEW FAN ANTI FUNGUS SKEW FAN

QUANTITY 11

MATERIAL ACRYLO NITRILE STYRENE ACRYLO NITRILE STYRENE

DRIVE DIRECT DIRECT

DIAMETER mm/in 97 / 3.8 97 / 3.8

LENGTH mm/in 717.5 / 28.2 717.5 / 28.2

INDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP24 IP24

OUTDOOR FAN

TYPE PROPELLER PROPELLER

QUANTITY 11

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT DIRECT

DIAMETER mm/in 404 / 16 404 / 16

OUTDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP24 IP24

COMPRESSOR

TYPE ROTARY HERMETIC ROTARY HERMETIC

OIL TYPE RB68A OR FREOL ALPHA68M RB68A OR FREOL ALPHA68M

OIL AMOUNT cm

/ ﬂ .oz. 350 / 12.3 430 / 15.1

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.234 / 2.516 0.234 / 2.516

ROW 22

FIN PER INCH 18 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 9.52 / 3/8 9.52 / 3/8

THICKNESS mm/in 0.33 / 0.013 0.33 / 0.013

FIN

MATERIAL ALUMINIUM (SLIT FIN) ALUMINIUM (SLIT FIN)

THICKNESS mm/in 0.11 / 0.004 0.11 / 0.004

FACE AREA m

/ft

0.36 / 3.94 0.36 / 3.94

ROW 11

FIN PER INCH 18 18

AIR QUALITY

FILTER

TYPE NANO FILTER NANO FILTER

QUANTITY pc 22

SIZE

LENGTH mm/in 304 / 11.9 304 / 11.9

WIDTH mm/in 348 / 13.7 348 / 13.7

THICKNESS mm/in 1.5 / 0.06 1.5 / 0.06

NEGATIVE IONIZER YES YES

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE HIGH IMPACT POLYSTYRENE

COLOUR IVORY IVORY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL GALVANISED MILD STEEL

COLOUR LIGHT GREY LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 64

Engineering & Physical Data AWM-G-2009

Component Data - Cooling Only (R410A)

MODEL

INDOOR UNIT A5WM 20G A5WM 25G

OUTDOOR UNIT A5LC 20C A5LC 25C

INDOOR FAN

TYPE ANTI FUNGUS SKEW FAN ANTI FUNGUS SKEW FAN

QUANTITY 11

MATERIAL ACRYLO NITRILE STYRENE ACRYLO NITRILE STYRENE

DRIVE DIRECT DIRECT

DIAMETER mm/in 108 / 4.25 108 / 4.25

LENGTH mm/in 810 / 31.9 810 / 31.9

INDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP20 IP20

OUTDOOR FAN

TYPE PROPELLER PROPELLER

QUANTITY 11

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT DIRECT

DIAMETER mm/in 457.2 / 18 457.2 / 18

OUTDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP54 IP54

COMPRESSOR

TYPE ROTARY HERMETIC ROTARY HERMETIC

OIL TYPE RB68A ORFREOL ALPHA68M RB68A ORFREOL ALPHA68M

OIL AMOUNT cm

/ ﬂ .oz. 670 / 23.5 1130 / 39.7

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.269 / 2.900 0.269 / 2.900

ROW 22

FIN PER INCH 18 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL ALUMINIUM (CORR. FIN) ALUMINIUM (CORR. FIN)

THICKNESS mm/in 0.127 / 0.005 0.127 / 0.005

FACE AREA m

/ft

0.51 / 5.47 0.62 / 6.64

ROW 22

FIN PER INCH 18 18

AIR QUALITY

FILTER

TYPE NANO FILTER NANO FILTER

QUANTITY pc 22

SIZE

LENGTH mm/in 351/13.8 351/13.8

WIDTH mm/in 386 / 15.2 386 / 15.2

THICKNESS mm/in 1.5 / 0.06 1.5 / 0.06

NEGATIVE IONIZER YES YES

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE HIGH IMPACT POLYSTYRENE

COLOUR IVORY IVORY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL GALVANISED MILD STEEL

COLOUR LIGHT GREY LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 65

AWM-G-2009 Engineering & Physical Data

Component Data - Cooling Only (R410A)

MODEL

INDOOR UNIT A5WM 311

OUTDOOR UNIT A5LC 28C

INDOOR FAN

TYPE ANTI FUNGUS CROSS FLOW FAN

QUANTITY 1

MATERIAL ACRYLO NITRILE STYRENE

DRIVE DIRECT

DIAMETER mm/in 106 / 4.17

LENGTH mm/in 950 / 37.4

INDOOR FAN MOTOR

TYPE INDUCTION

QUANTITY 1

INDEX OF PROTECTION (IP) IP24

OUTDOOR FAN

TYPE PROPELLER

QUANTITY 1

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT

DIAMETER mm/in 457.2 / 18

OUTDOOR FAN MOTOR

TYPE INDUCTION

QUANTITY 1

INDEX OF PROTECTION (IP) IP54

COMPRESSOR

TYPE ROTARY HERMETIC

OIL TYPE RB68A ORFREOL ALPHA68M

OIL AMOUNT cm

/ ﬂ .oz. 1130 / 39.7

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043

FACE AREA m

/ft

0.30 / 3.23

ROW 2

FIN PER INCH 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011

FIN

MATERIAL ALUMINIUM (CORR. FIN)

THICKNESS mm/in 0.11/0.004

FACE AREA m

/ft

0.62 / 6.63

ROW 2

FIN PER INCH 18

AIR QUALITY

FILTER

TYPE SARANET + IONIZER

QUANTITY pc 3 X 3

SIZE

LENGTH mm/in 330 / 13.0

WIDTH mm/in 317 / 12.4

THICKNESS mm/in 1.8 / 0.07

NEGATIVE IONIZER NO

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE

COLOUR IVORY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL

COLOUR LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 66

Engineering & Physical Data AWM-G-2009

Component Data - Heat Pump (R410A)

MODEL

INDOOR UNIT A5WM 07GR A5WM 09GR

OUTDOOR UNIT A5LC 07CR A5LC 10CR

INDOOR FAN

TYPE ANTI FUNGUS SKEW FAN CROSS FLOW FAN

QUANTITY 11

MATERIAL ACRYLO NITRILE STYRENE ACRYLO NITRILE STYRENE

DRIVE DIRECT DIRECT

DIAMETER mm/in 97 / 3.8 97 / 3.8

LENGTH mm/in 617.5 / 24.3 617.5 / 24.3

INDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP24 IP24

OUTDOOR FAN

TYPE PROPELLER PROPELLER

QUANTITY 11

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT DIRECT

DIAMETER mm/in 356 / 14 356 / 14

OUTDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP54 IP54

COMPRESSOR

TYPE ROTARY HERMETIC ROTARY HERMETIC

OIL TYPE RB68A OR FREOL ALPHA68M RB68A OR FREOL ALPHA68M

OIL AMOUNT cm

/ ﬂ .oz. 300 / 10.5 350 / 12.3

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.201 / 2.161 0.201 / 2.161

ROW 22

FIN PER INCH 18 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 9.52 / 3/8 7.0 / 0.276

THICKNESS mm/in 0.33 / 0.013 0.28 / 0.011

FIN

MATERIAL ALUMINIUM (SLIT FIN) RAISE LANCE

THICKNESS mm/in 0.11 / 0.004 0.1 / 0.004

FACE AREA m

/ft

0.31 / 3.40 0.193 / 2.112

ROW 11

FIN PER INCH 18 18

AIR QUALITY

FILTER

TYPE NANO FILTER NANO FILTER

QUANTITY pc 22

SIZE

LENGTH mm/in 304 / 11.9 304 / 11.9

WIDTH mm/in 298 / 11.7 298 / 11.7

THICKNESS mm/in 1.5 / 0.06 1.5 / 0.06

NEGATIVE IONIZER YES YES

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE HIGH IMPACT POLYSTYRENE

COLOUR IVORY IVORY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL GALVANISED MILD STEEL

COLOUR LIGHT GREY LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 67

AWM-G-2009 Engineering & Physical Data

Component Data - Heat Pump (R410A)

MODEL

INDOOR UNIT A5WM 10GR A5WM 15GR

OUTDOOR UNIT A5LC 10CR A5LC 15CR

INDOOR FAN

TYPE ANTI FUNGUS SKEW FAN CROSS FLOW FAN

QUANTITY 11

MATERIAL ACRYLO NITRILE STYRENE ACRYLO NITRILE STYRENE

DRIVE DIRECT DIRECT

DIAMETER mm/in 97 / 3.8 97 / 3.8

LENGTH mm/in 717.5 / 28.2 717.5 / 28.2

INDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP24 IP24

OUTDOOR FAN

TYPE PROPELLER PROPELLER

QUANTITY 11

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT DIRECT

DIAMETER mm/in 404 / 16 404 / 16

OUTDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP54 IP54

COMPRESSOR

TYPE ROTARY HERMETIC ROTARY HERMETIC

OIL TYPE RB68A OR FREOL ALPHA68M RB68A OR FREOL ALPHA68M

OIL AMOUNT cm

/ ﬂ .oz. 350 / 12.3 430 / 15.1

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.234 / 2.516 0.234 / 2.516

ROW 22

FIN PER INCH 18 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 9.52 / 3/8

THICKNESS mm/in 0.28 / 0.011 0.33 / 0.013

FIN

MATERIAL RAISE LANCE ALUMINIUM (SLIT FIN)

THICKNESS mm/in 0.1 / 0.004 0.11 / 0.004

FACE AREA m

/ft

0.36 / 3.94 0.36 / 3.94

ROW 11

FIN PER INCH 18 18

AIR QUALITY

FILTER

TYPE NANO FILTER NANO FILTER

QUANTITY pc 22

SIZE

LENGTH mm/in 304 / 11.9 304 / 11.9

WIDTH mm/in 348 / 13.7 348 / 13.7

THICKNESS mm/in 1.5 / 0.06 1.5 / 0.06

NEGATIVE IONIZER YES YES

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE HIGH IMPACT POLYSTYRENE

COLOUR IVORY IVORY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL GALVANISED MILD STEEL

COLOUR LIGHT GREY LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 68

Engineering & Physical Data AWM-G-2009

Component Data - Heat Pump (R410A)

MODEL

INDOOR UNIT A5WM 20GR A5WM 25GR

OUTDOOR UNIT A5LC 20CR A5LC 25CR

INDOOR FAN

TYPE CROSS FLOW FAN CROSS FLOW FAN

QUANTITY 11

MATERIAL ACRYLO NITRILE STYRENE ACRYLO NITRILE STYRENE

DRIVE DIRECT DIRECT

DIAMETER mm/in 108 / 4.25 108 / 4.25

LENGTH mm/in 810 / 31.9 810 / 31.9

INDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP20 IP20

OUTDOOR FAN

TYPE PROPELLER PROPELLER

QUANTITY 11

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT DIRECT

DIAMETER mm/in 457.2/18 457.2/18

OUTDOOR FAN MOTOR

TYPE INDUCTION INDUCTION

QUANTITY 11

INDEX OF PROTECTION (IP) IP54 IP54

COMPRESSOR

TYPE ROTARY HERMETIC ROTARY HERMETIC

OIL TYPE RB68A OR FREOL ALPHA68M RB68A OR FREOL ALPHA68M

OIL AMOUNT cm

/ ﬂ .oz. 670 / 23.5 1130 / 39.7

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043 0.11 / 0.0043

FACE AREA m

/ft

0.269 / 2.900 0.269 / 2.900

ROW 22

FIN PER INCH 18 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011 0.28 / 0.011

FIN

MATERIAL RAISE LANCE RAISE LANCE

THICKNESS mm/in 0.1 / 0.004 0.1 / 0.004

FACE AREA m

/ft

0.51 / 5.47 0.62 / 6.64

ROW 22

FIN PER INCH 18 18

AIR QUALITY

FILTER

TYPE NANO FILTER NANO FILTER

QUANTITY pc 22

SIZE

LENGTH mm/in 351 / 13.8 351 / 13.8

WIDTH mm/in 386 / 15.2 386 / 15.2

THICKNESS mm/in 1.5 / 0.06 1.5 / 0.06

NEGATIVE IONIZER YES YES

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE HIGH IMPACT POLYSTYRENE

COLOUR IVORY IVORY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL GALVANISED MILD STEEL

COLOUR LIGHT GREY LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 69

AWM-G-2009 Engineering & Physical Data

Component Data - Heat Pump (R410A)

MODEL

INDOOR UNIT A5WM 301R

OUTDOOR UNIT A5LC - 28CR

INDOOR FAN

TYPE ANTI FUNGUS CROSS FLOW FAN

QUANTITY 1

MATERIAL ACRYLO NITRILE STYRENE

DRIVE DIRECT

DIAMETER mm/in 106 / 4.17

LENGTH mm/in 950 / 37.4

INDOOR FAN MOTOR

TYPE INDUCTION

QUANTITY 1

INDEX OF PROTECTION (IP) IP24

OUTDOOR FAN

TYPE PROPELLER

QUANTITY 1

MATERIAL

GLASS REINFORCED ACRYL

STYRENE RESIN

DRIVE DIRECT

DIAMETER mm/in 457.2/18

OUTDOOR FAN MOTOR

TYPE INDUCTION

QUANTITY 1

INDEX OF PROTECTION (IP) IP54

COMPRESSOR

TYPE ROTARY HERMETIC

OIL TYPE RB68A OR FREOL ALPHA68M

OIL AMOUNT cm

/ ﬂ .oz. 1130 / 39.7

INDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011

FIN

MATERIAL

ALUMINIUM (HYDROPHILIC SLIT

FIN TYPE)

THICKNESS mm/in 0.11 / 0.0043

FACE AREA m

/ft

0.30 / 3.23

ROW 2

FIN PER INCH 18

OUTDOOR COIL

TUBE

MATERIAL

SEAMLESS INNER GROOVE

COPPER

DIAMETER mm/in 7.0 / 0.276

THICKNESS mm/in 0.28 / 0.011

FIN

MATERIAL ALUMINIUM (CORR. FIN)

THICKNESS mm/in 0.11 / 0.004

FACE AREA m

/ft

0.62 / 6.63

ROW 2

FIN PER INCH 18

AIR QUALITY

FILTER

TYPE SARANET + IONIZER

QUANTITY pc 3 X 3

SIZE

LENGTH mm/in 330 / 13.0

WIDTH mm/in 317 / 12.4

THICKNESS mm/in 1.8 / 0.07

NEGATIVE IONIZER NO

CASING

INDOOR UNIT

MATERIAL HIGH IMPACT POLYSTYRENE

COLOUR IVORY

OUTDOOR UNIT

MATERIAL GALVANISED MILD STEEL

COLOUR LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

Page 70

Performance Data AWM-G-2009

Performance Data

Interpolation and Extrapolation method can be used to get the total capacity, TC and sensible capacity, SC at those temperatures which are not stated out in the table.

Example:

Model: AWM 10G - ALC 10C Indoor Condition: 23°C DB, 15°C WB Outdoor Condition: 37°C DB

Solution:

Overall

Based on the Performance Table

1. Refer to the Indoor DB column,

23°C is located between 20°C and 24°C (Thus, Interpolation need to be applied)

2. Refer to the Indoor WB column,

15°C only available in the case of Indoor DB = 20°C. (Thus, Extrapolation between 16°C WB and 17°C WB during 24°C indoor DB is required)

3. Refer to the Outdoor DB column,

37°C is located between 35°C and 40°C. (Thus, Interpolation need to be applied)

Please follow the steps below in order to get the required capacity.

1st Step Extrapolation of Indoor WB

Find TC, SC for (a)

Indoor: 24°C DB, 15°C WB

Outdoor: 35°C DB

(b) Indoor: 24°C DB, 15°C WB

Outdoor: 40°C DB

2nd Step Interpolation of Indoor DB

Find TC, SC for (a)

Indoor: 23°C DB, 15°C WB

Outdoor:

35°C DB

(b) Indoor: 23°C DB, 15°C WB

Outdoor: 40°C DB

Step

Interpolation of Outdoor DB

Find TC, SC for (a) Indoor: 23°C DB, 15°C WB

Outdoor: 37°C DB

Page 71

AWM-G-2009 Performance Data

Calculation Steps

Details:

Step:

To obtain the Total capacity and Sensible capacity for

(a) Indoor Condition: 24°C DB, 15°C WB

Outdoor Condition: 35°C DB

Indoor DB˚C Indoor WB˚C

Outdoor DB, ˚C

TC (kW) SC (kW)

........

...........................................

16 2.623 1.892

17 2.687 1.794

Total capacity, TC

⇒ x

= 2.558kW (Same as Total capacity at 20°C Indoor DB / 15°C Indoor WB & 35°C Outdoor WB)*

Sensible capacity, SC

Extrapolation Method:

⇒

17º C – 15º C

1.794kW – y

17º C – 16º C 1.794kW – 1.892kW

⇒ y

= 1.990kW

(b) Indoor Condition: 24°C DB, 15°C WB

Outdoor Condition: 40°C DB

Indoor DB˚C Indoor WB˚C

Outdoor DB, ˚C

TC (kW) SC (kW)

........

...........................................

16 2.429 1.728

17 2.502 1.653

Total capacity, TC

⇒ x2 = 2.355kW (Same as Total capacity at 20°C Indoor DB / 15°C Indoor WB & 40°C Outdoor WB)*

Sensible capacity, SC

Extrapolation Method:

⇒

17º C – 15º C

1.653kW – y

17º C – 16º C 1.653kW – 1.728kW

⇒ y

= 1.802kW

* This is due to 2 different conditions with same WB temperature, will have the same level of enthalpy. For more

details, please refer to psychrometrics chart

Page 72

Performance Data AWM-G-2009

2nd Step:

To obtain the Total capacity and Sensible capacity for

(a) Indoor Condition: 23°C DB, 15°C WB

Outdoor Condition: 35°C DB

Indoor DB˚C Indoor WB˚C

Outdoor DB, ˚C

TC (kW) SC (kW)

........

20 15

...........................................

2.558 1.403

23 15

24 15 2.558 1.990

Total capacity, TC

⇒ x

= 2.558kW (Same as Total capacity at 20°C Indoor DB / 15°C Indoor WB & 35°C Outdoor WB)*

Sensible capacity, SC

Interpolation Method:

⇒

24º C – 20º C

1.990kW – 1.181kW

24º C – 23º C 1.990kW – y

⇒ y

= 1.844kW

(b) Indoor Condition: 23°C DB, 15°C WB

Outdoor Condition: 40°C DB

Indoor DB˚C Indoor WB˚C

Outdoor DB, ˚C

TC (kW) SC (kW)

........

20 15

...........................................

2.355 1.215

23 15

24 15 2.355 1.802

Total capacity, TC

⇒ x4 = 2.355kW (Same as Total capacity at 20°C Indoor DB / 15°C Indoor WB & 40°C Outdoor WB)*

Sensible capacity, SC

Interpolation Method:

⇒

24º C – 20º C

1.597kW – 0.963kW

24º C – 23º C 1.597kW – y

⇒ y2 = 1.655kW

* This is due to 2 different conditions with same WB temperature, will have the same level of enthalpy. For more

details, please refer to psychrometrics chart

Page 73

AWM-G-2009 Performance Data

3rd Step:

To obtain the Total capacity and Sensible capacity for

(a) Indoor Condition: 23°C DB, 15°C WB

Outdoor Condition: 37°C DB

Indoor DB˚C Indoor WB˚C

Outdoor DB, ˚C

35 37 40

TC (kW) SC (kW) TC (kW) SC (kW) TC (kW) SC (kW)

........

23 15

......................

2.558 1.844 x y 2.355 1.655

Total capacity, TC

Interpolation Method:

⇒

40º C – 35º C

2.355kW – 2.558kW

40º C – 37º C 2.355kW –

⇒ x = 2.477kW

Sensible capacity, SC

Interpolation Method:

⇒

40º C – 35º C

1.655kW – 1.844kW

40º C – 37º C 1.655kW – y

⇒ y = 1.768kW

Page 74

Performance Data AWM-G-2009

Cooling Only (R22)

Model: AWM 07G - ALC 07C Cooling Mode

DB°C

WB°C

Outdoor DB°C

20 25 30 35 40 46

TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW)

15 2.418 1.484 2.249 1.335 2.080 1.186 1.910 1.037 1.741 0.889 1.538 0.710

16 2.453 1.349 2.286 1.221 2.119 1.094 1.952 0.966 1.785 0.839 1.585 0.686

16 2.453 1.799 2.286 1.671 2.119 1.544 1.952 1.416 1.785 1.288 1.585 1.135

17 2.488 1.664 2.323 1.558 2.159 1.451 1.994 1.346 1.829 1.239 1.632 1.111

18 2.523 1.529 2.360 1.444 2.198 1.359 2.036 1.274 1.873 1.189 1.679 1.087

19 2.557 1.394 2.397 1.331 2.237 1.267 2.077 1.203 1.917 1.139 1.725 1.062

20 2.593 1.259 2.437 1.210 2.281 1.162 2.126 1.113 1.970 1.064 1.783 1.006

18 2.523 1.979 2.360 1.894 2.198 1.809 2.036 1.724 1.873 1.638 1.679 1.536

19 2.557 1.844 2.397 1.780 2.237 1.716 2.077 1.652 1.917 1.589 1.725 1.512

20 2.593 1.709 2.437 1.660 2.281 1.611 2.126 1.563 1.970 1.514 1.783 1.456

21 2.628 1.573 2.478 1.535 2.328 1.498 2.179 1.460 2.029 1.423 1.849 1.378

22 2.663 1.437 2.519 1.411 2.375 1.384 2.231 1.358 2.087 1.332 1.915 1.300

23 2.699 1.301 2.560 1.286 2.422 1.271 2.284 1.256 2.146 1.241 1.980 1.223

24 2.734 1.165 2.602 1.161 2.469 1.157 2.337 1.154 2.205 1.150 2.046 1.145

20 2.593 1.934 2.437 1.885 2.281 1.836 2.126 1.788 1.970 1.739 1.783 1.680

21 2.628 1.798 2.478 1.760 2.328 1.723 2.179 1.685 2.029 1.648 1.849 1.603

22 2.663 2.008 2.519 1.636 2.375 1.609 2.231 1.583 2.087 1.557 1.915 1.525

23 2.699 1.839 2.560 1.511 2.422 1.496 2.284 1.481 2.146 1.466 1.980 1.448

24 2.734 1.670 2.602 1.386 2.469 1.382 2.337 1.379 2.205 1.375 2.046 1.370

Model: AWM 09G - ALC 09C Cooling Mode

DB°C

WB°C

Outdoor DB°C

20 25 30 35 40 46

TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW)

15 3.034 1.916 2.829 1.742 2.623 1.568 2.418 1.393 2.213 1.219 1.966 1.010

16 3.114 1.748 2.903 1.597 2.692 1.445 2.480 1.294 2.269 1.142 2.016 0.961

16 3.114 2.257 2.903 2.105 2.692 1.954 2.480 1.802 2.269 1.651 2.016 1.469

17 3.194 2.088 2.977 1.960 2.760 1.831 2.543 1.703 2.326 1.574 2.065 1.420

18 3.274 1.920 3.051 1.815 2.828 1.709 2.605 1.603 2.382 1.497 2.115 1.371

19 3.354 1.752 3.125 1.669 2.896 1.586 2.668 1.504 2.439 1.421 2.164 1.321

20 3.435 1.583 3.205 1.519 2.976 1.454 2.747 1.389 2.517 1.324 2.242 1.246

18 3.274 2.429 3.051 2.323 2.828 2.217 2.605 2.112 2.382 2.006 2.115 1.879

19 3.354 2.261 3.125 2.178 2.896 2.095 2.686 2.012 2.439 1.929 2.164 1.830

20 3.435 2.092 3.205 2.027 2.976 1.962 2.747 1.897 2.517 1.833 2.242 1.755

21 3.516 1.923 3.289 1.873 3.063 1.823 2.837 1.773 2.611 1.723 2.339 1.663

22 3.597 1.754 3.374 1.719 3.150 1.683 2.927 1.648 2.704 1.613 2.436 1.571

23 3.678 1.585 3.458 1.564 3.238 1.544 3.018 1.524 2.798 1.503 2.533 1.479

24 3.759 1.416 3.542 1.410 3.325 1.404 3.108 1.399 2.891 1.393 2.631 1.387

20 3.435 2.346 3.205 2.281 2.976 2.216 2.747 2.152 2.517 2.087 2.242 2.009

21 3.516 2.177 3.289 2.127 3.063 2.077 2.837 2.027 2.611 1.977 2.339 1.917

22 3.597 2.008 3.374 1.973 3.150 1.938 2.927 1.902 2.704 1.867 2.436 1.825

23 3.678 1.839 3.458 1.819 3.238 1.798 3.018 1.778 2.798 1.757 2.533 1.733

24 3.759 1.670 3.542 1.664 3.325 1.659 3.108 1.653 2.891 1.648 2.631 1.641

Page 75

AWM-G-2009 Performance Data

Cooling Only (R22)

Model: AWM 10G - ALC 10C Cooling Mode

DB°C

WB°C

Outdoor DB°C

20 25 30 35 40 46

TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW)

15 3.169 1.968 2.966 1.780 2.762 1.592 2.558 1.403 2.355 1.215 2.111 0.989

16 3.206 1.800 3.012 1.635 2.817 1.470 2.623 1.306 2.429 1.141 2.195 0.943

16 3.206 2.386 3.012 2.222 2.817 2.057 2.623 1.892 2.429 1.728 2.195 1.530

17 3.243 2.218 3.058 2.077 2.872 1.936 2.687 1.794 2.502 1.653 2.280 1.484

18 3.280 2.049 3.104 1.932 2.928 1.814 2.752 1.697 2.576 1.579 2.364 1.438

19 3.317 1.881 3.150 1.787 2.983 1.693 2.816 1.599 2.649 1.505 2.449 1.392

20 3.353 1.711 3.193 1.635 3.033 1.559 2.873 1.483 2.713 1.407 2.521 1.315

18 3.280 2.636 3.104 2.518 2.928 2.401 2.752 2.283 2.576 2.166 2.364 2.025

19 3.317 2.467 3.150 2.373 2.983 2.279 2.816 2.186 2.649 2.092 2.449 1.979

20 3.353 2.298 3.193 2.222 3.033 2.146 2.873 2.070 2.713 1.993 2.521 1.902

21 3.389 2.128 3.235 2.066 3.080 2.004 2.925 1.942 2.771 1.879 2.585 1.805

22 3.426 1.959 3.276 1.910 3.127 1.862 2.978 1.814 2.828 1.765 2.649 1.707

23 3.462 1.789 3.318 1.754 3.174 1.720 3.030 1.686 2.886 1.651 2.713 1.610

24 3.499 1.619 3.360 1.599 3.221 1.578 3.082 1.558 2.943 1.537 2.776 1.513

20 3.353 2.591 3.193 2.515 3.033 2.439 2.873 2.363 2.713 2.287 2.521 2.195

21 3.389 2.422 3.235 2.359 3.080 2.297 2.925 2.235 2.771 2.173 2.585 2.098

22 3.426 2.252 3.276 2.204 3.127 2.155 2.978 2.107 2.828 2.059 2.649 2.001

23 3.462 2.082 3.318 2.048 3.174 2.013 3.030 1.979 2.886 1.945 2.713 1.903

24 3.499 1.912 3.360 1.892 3.221 1.872 3.082 1.851 2.943 1.831 2.776 1.806

Model: AWM 15G - ALC 15C Cooling Mode

DB°C

WB°C

Outdoor DB°C

20 25 30 35 40 46

TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW)

15 4.051 2.628 3.785 2.373 3.519 2.118 3.253 1.863 2.987 1.608 2.668 1.302

16 4.086 2.387 3.834 2.156 3.582 1.925 3.330 1.694 3.078 1.464 2.776 1.186

16 4.086 3.056 3.834 2.825 3.582 2.594 3.330 2.363 3.078 2.133 2.776 1.855

17 4.120 2.815 3.882 2.608 3.645 2.402 3.407 2.195 3.169 1.988 2.884 1.740

18 4.155 2.574 3.931 2.392 3.707 2.209 3.484 2.026 3.260 1.843 2.991 1.624

19 4.189 2.333 3.980 2.175 3.770 2.016 3.560 1.858 3.351 1.699 3.099 1.509

20 4.223 2.093 4.025 1.961 3.826 1.830 3.627 1.699 3.428 1.568 3.190 1.410

18 4.155 3.243 3.931 3.061 3.707 2.878 3.484 2.695 3.260 2.513 2.991 2.293

19 4.189 3.002 3.980 2.844 3.770 2.685 3.560 2.527 3.351 2.368 3.099 2.178

20 4.223 2.762 4.025 2.631 3.826 2.499 3.627 2.368 3.428 2.237 3.190 2.079

21 4.257 2.521 4.067 2.420 3.877 2.318 3.687 2.216 3.498 2.115 3.270 1.993

22 4.291 2.281 4.110 2.209 3.929 2.137 3.748 2.065 3.567 1.993 3.349 1.906

23 4.325 2.041 4.153 1.998 3.980 1.956 3.808 1.913 3.636 1.871 3.429 1.819

24 4.359 1.801 4.195 1.788 4.032 1.775 3.868 1.761 3.705 1.748 3.508 1.733

20 4.223 3.096 4.025 2.965 3.826 2.834 3.627 2.703 3.428 2.571 3.190 2.414

21 4.257 2.856 4.067 2.754 3.877 2.653 3.687 2.551 3.498 2.449 3.270 2.327

22 4.291 2.616 4.110 2.544 3.929 2.471 3.748 2.399 3.567 2.327 3.349 2.241

23 4.325 2.375 4.153 2.333 3.980 2.290 3.808 2.248 3.636 2.205 3.429 2.154

24 4.359 2.135 4.195 2.122 4.032 2.109 3.868 2.096 3.705 2.083 3.508 2.067

Page 76

Performance Data AWM-G-2009

Cooling Only (R22)

Model: AWM 20G - ALC 18C Cooling Mode

DB°C

WB°C

Outdoor DB°C

20 25 30 35 40 46

TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW)

15 5.954 3.645 5.566 3.311 5.179 2.977 4.791 2.642 4.404 2.308 3.939 1.907

16 6.132 3.309 5.730 3.009 5.329 2.709 4.927 2.409 4.525 2.109 4.043 1.749

16 6.132 4.352 5.730 4.052 5.329 3.752 4.927 3.451 4.525 3.151 4.043 2.791

17 6.310 4.016 5.894 3.750 5.478 3.484 5.062 3.218 4.646 2.952 4.147 2.633

18 6.488 3.680 6.058 3.448 5.628 3.216 5.198 2.985 4.767 2.753 4.251 2.475

19 6.667 3.344 6.222 3.147 5.778 2.949 5.333 2.751 4.888 2.554 4.355 2.317

20 6.846 3.008 6.397 2.846 5.947 2.684 5.498 2.521 5.049 2.359 4.510 2.164

18 6.488 4.723 6.058 4.491 5.628 4.259 5.198 4.027 4.767 3.795 4.251 3.517

19 6.667 4.387 6.222 4.189 5.778 3.991 5.333 3.794 4.888 3.596 4.355 3.359

20 6.846 4.051 6.397 3.889 5.947 3.726 5.498 3.564 5.049 3.401 4.510 3.206

21 7.026 3.715 6.578 3.589 6.131 3.462 5.683 3.336 5.235 3.209 4.698 3.058

22 7.206 3.380 6.760 3.289 6.314 3.199 5.868 3.108 5.422 3.017 4.886 2.909

23 7.386 3.044 6.942 2.989 6.497 2.935 6.053 2.880 5.608 2.826 5.075 2.60

24 7.567 2.708 7.124 2.689 6.681 2.671 6.238 2.652 5.795 2.634 5.263 2.611

20 6.846 4.572 6.397 4.410 5.947 4.247 5.498 4.085 5.049 3.923 4.510 3.728

21 7.026 4.236 6.578 4.110 6.131 3.984 5.683 3.857 5.235 3.731 4.698 3.579

22 7.206 3.901 6.760 3.810 6.314 3.720 5.868 3.629 5.422 3.539 4.886 3.430

23 7.386 3.565 6.942 3.511 6.497 3.456 6.053 3.401 5.608 3.347 5.075 3.281

24 7.567 3.229 7.124 3.211 6.681 3.192 6.238 3.174 5.795 3.155 5.263 3.133

Model: AWM 20G - ALC 20C Cooling Mode

DB°C

WB°C

Outdoor DB°C

20 25 30 35 40 46

TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW)

15 5.778 3.640 5.473 3.396 5.169 3.153 4.864 2.909 4.559 2.666 4.194 2.373

16 6.026 3.334 5.701 3.125 5.376 2.917 5.051 2.709 4.726 2.501 4.336 2.251

16 6.026 4.248 5.701 4.040 5.376 3.832 5.051 3.624 4.726 3.416 4.336 3.166

17 6.274 3.942 5.929 3.770 5.583 3.597 5.238 3.424 4.892 3.252 4.478 3.044

18 6.523 3.636 6.157 3.499 5.791 3.362 5.425 3.224 5.059 3.087 4.620 2.922

19 6.771 3.330 6.384 3.228 5.998 3.126 5.612 3.025 5.225 2.923 4.762 2.800

20 7.019 3.023 6.614 2.947 6.210 2.870 5.805 2.794 5.400 2.718 4.915 2.626

18 6.523 4.551 6.157 4.414 5.791 4.276 5.425 4.139 5.059 4.002 4.620 3.837

19 6.771 4.245 6.384 4.143 5.998 4.041 5.612 3.939 5.225 3.837 4.762 3.715

20 7.019 3.938 6.614 3.861 6.210 3.785 5.805 3.709 5.400 3.633 4.915 3.514

21 7.268 3.630 6.846 3.572 6.424 3.515 6.003 3.458 5.581 3.401 5.075 3.332

22 7.516 3.321 7.077 3.283 6.639 3.245 6.200 3.207 5.761 3.169 5.235 3.123

23 7.765 3.013 7.309 2.994 6.853 2.975 6.398 2.956 5.942 2.937 5.395 2.914

24 8.013 2.705 7.541 2.705 7.068 2.705 6.595 2.705 6.123 2.705 5.556 2.705

20 7.019 4.395 6.614 4.319 6.210 4.242 5.805 4.166 5.400 4.090 4.915 3.998

21 7.268 4.087 6.846 4.030 6.424 3.973 6.003 3.915 5.581 3.858 5.075 3.789

22 7.516 3.779 7.077 3.741 6.639 3.703 6.200 3.664 5.761 3.626 5.235 3.581

23 7.765 3.471 7.309 3.452 6.853 3.433 6.398 3.414 5.942 3.394 5.395 3.372

24 8.013 3.163 7.541 3.163 7.068 3.163 6.595 3.163 6.123 3.163 5.556 3.163

Page 77

AWM-G-2009 Performance Data

Cooling Only (R22)

Model: AWM 25G - ALC 25C Cooling Mode

DB°C

WB°C

Outdoor DB°C

20 25 30 35 40 46

TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW)

15 7.657 5.145 7.196 4.692 6.735 4.238 6.275 3.785 5.814 3.331 5.261 2.787

16 7.728 4.693 7.300 4.280 6.873 3.867 6.446 3.454 6.019 3.042 5.507 2.546

16 7.728 5.852 7.300 5.439 6.873 5.026 6.446 4.614 60.19 4.201 5.507 3.705

17 7.798 5.400 7.405 5.028 7.011 4.656 6.618 4.283 6.224 3.911 5.752 3.464

18 7.869 4.948 7.509 4.617 7.149 4.285 6.789 3.953 6.430 3.621 5.998 3.223

19 7.940 4.496 7.613 4.205 7.287 3.914 6.961 3.623 6.635 3.332 6.243 2.982

20 8.008 4.045 7.701 3.803 7.394 3.560 7.086 3.318 6.779 3.075 6.410 2.784

18 7.869 6.107 7.509 5.776 7.149 5.444 6.789 5.112 6.430 4.781 5.998 4.383

19 7.940 5.655 7.613 5.364 7.287 5.073 6.961 4.782 6.635 4.491 6.243 4.142

20 8.008 5.205 7.701 4.962 7.394 4.720 7.086 4.477 6.779 4.235 6.410 3.944

21 8.076 4.754 7.778 4.566 7.479 4.377 7.181 4.189 6.883 4.000 6.525 3.774

22 8.144 4.304 7.855 4.169 7.565 4.035 7.276 3.900 6.986 3.766 6.639 3.604

23 8.212 3.854 7.931 3.773 7.651 3.693 7.370 3.612 7.090 3.532 6.754 3.435

24 8.279 3.403 8.008 3.377 7.737 3.350 7.465 3.324 7.194 3.297 6.868 3.265

20 8.008 5.784 7.701 5.542 7.394 5.299 7.086 5.057 6.779 4.814 6.410 4.523

21 8.076 5.334 7.778 5.145 7.479 4.957 7.181 4.768 6.883 4.580 6.525 4.354

22 8.144 4.883 7.855 4.749 7.565 4.614 7.276 4.480 6.986 4.345 6.639 4.184

23 8.212 4.433 7.931 4.353 7.651 4.272 7.370 4.192 7.090 4.111 6.754 4.015

24 8.279 3.983 8.008 3.956 7.737 3.930 7.465 3.903 7.194 3.877 6.868 3.845

Model: AWM 301 - ALC 28C Cooling Mode

DB°C

WB°C

Outdoor DB°C

20 25 30 35 40 46

TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW) TC(kW) SC(kW)

15 7.657 5.145 7.196 4.692 6.735 4.238 6.275 3.785 5.814 3.331 5.261 2.787

16 7.728 4.693 7.300 4.280 6.873 3.867 6.446 3.454 6.019 3.042 5.507 2.546

16 7.728 5.852 7.300 5.439 6.873 5.026 6.446 4.614 6.019 4.201 5.507 3.705